Related
hello all,
i'm a newscommer on this forum,i've trust in upgrade my phone with aku3
i correctly followed the topic , install step 1 (forG3) and step 2
my device worked fine after the first install (qteck 2.15 fr ->2.2 from step1)
i've synchronize my phone, and run the second part, installing without problems, reboot > freeze on the boot screen htc
no way to synchronize again. my phone is reconized by mtty (1.51 and 1.50) but i don't know how to use it
ipl 2.09
spl 2.20.0000
gsm 02.47.21
os 3.0.0.0
i've tried all the night to find a solution on all forum i knew, i drive me to this one, i think it could help me best ( you'r pro dudes )
but i'm allways stick. i've call htc division hotline (i'm from france) , they said i have to send back my phone ( but he's now out of waranty, cause it's not a legal rom i've installed, so i have to paid, and i've allready too much invest on my device)
plz said me there is still a hope!
did try upload another rom from bootloader ?
did try upload another rom from bootloader ?
but first try a hard-reset
i don't know how to load a rom from bootloader (i allready have made soft and hard reset
no one could help me ?
1. dowenload this latest Qtek official rom from here: ftp://xda:[email protected]_220734_2207114_024721_QtekWWE_Ship.exe
2. enter your S200 into bootloader mode by pressing power +camera + reset, let go of the reset, but keep holding power + camera until the three colur screen will show up (that is bootloader mode).
3. connect the S200 to your pc (make sure your battery is fully charged)
4. run the Qtek official rom.
5. good luck!
i've tried those kind of upgrade several time, but without possibility of establishing an active sync connexion, it's impossible to launch the rom install...
does samebody knew if it's possible to make a rom dump with an emulator and copy it on a sd card for autoinstall backup in bootloader mode ?
while in bootloader you don't need to establish any activesync connection. just plug the usb cable, then if appears "usb" on phone you are good to go.
install the original DOPOD rom from the ftp.
this rom don't work, it give me the message
error 294 invalid vendor id
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
pti_nourson said:
it's now working ! great !
i've juste install again the step one of jester's aku3.3 (so, i'm on a 2.20 os, i think i'll keep it for a while )
thank you verry much
Click to expand...
Click to collapse
So you can now change your signature again, right
HI all,
I'm desperate...
I recently bought an 02 Orbit that was supposed to be unlocked.
So I downloaded PDAMobiz_Dopod_P800W_AKU301_v1.1.0_Lite.exe, unpacked it and double clicked on UpgradeRom_P800W.bat
A dos installation routine started, then I performed a hard reset by pressing the softkeys + stylus reset.
and now I"m stuck on the O2 logo, with some red informations written :
IPL 1.25.0001
SPL 1.25.0000
GSM 02.67.90
OS 1.28.0.0
but nothing else, the device doesn't boot :-(
I'm completely desperate... I had my Orbit working 1h only and now I still have my eyes to cry.
I've tried to install another ROM like ART_HTCWWE_11240501_026790_WWE_Ship, but when I launch ROMUpdateUtility.exe it says that no device is connected....
I tried to enter the bootloader but I don't understand how I could do that (by the way what do you guys mean by the record button? where is it?)
Could someone explain me how I can recover my crashed device please ?
Thanks in advance
ok I've found the record button and managed to enter the bootloader (red-green-blue screen right?). But it doesn't help. My device is not recognise by my PC anymore, no connection.
The problem is that I didn't make the procedure on IMEICHECK because the vendor said my Orbit was already unlocked. I know, I'm stupid, I should have....
Anyway, now I've my 30€ UNL file,
I've edited a ROM with the hex program, I've change "BsaD5SeoA" with "IMEICHECK save exe file" (I told you I'm stupid, or I didn't exactly understood what you mean, because I don't have any IMEICHECK.exe file)
I tried to launch a ROM upgrade but my device still not be recognised by my computer, even in bootloader mode.
Same **** when I try to launch the C3v1Unlock, it says no device connected.
Please, if you have anything to help me......
After i read this THREAD who explain how to repair my problem ...But it dosent work for me
When i want to flash it, it tell me :
INVALID MODEL ID ,with : RUU_Artemis_DOPODASIA_WWE_LOVE_1.28.717.1_INFINEon gsm4.1.13.30_02.69.90_Cmp_Ship_R.exe
INVALID UPDATE TOLL ,with : _ARTE_DOPODAU_12570702_026990_WWE_SHIP.exe
And after have made the TUTO !
Click to expand...
Click to collapse
I saw this post on an other thread... I am having the same problem... I bought artemis from ebay and the seller told me that it was unlocked... But i can't flash it with these ROMs... Did you find a solution? Is it really unlocked?
By the way when the window that tells me "INVALID MODEL ID" shows up at the bottom and to the right of the window there is i big number... Do you know what this is?
Same problem here
I have THE SAME problemhere. The same message on the boot screen. It seems that we are not able to use our XDA ORBIT ;( any more
At least we can download oreginal XDA Orbit english or German ROM OR if someone write RUU for Xda Orbit. Than would be easy - you just go to boot loader and you start your RUU, or easily put .NBH file to your micro SD and flash it from micro SD.Too bad I can just cry over my Xda Orbit. PLEEEASSEEE HELPPP
I also heard that FTP ROM site is going down ---- XDA GENOCIDE!!! What ARE you doing people!
Try the orbit ROM on ftp if it is still there
When a seller says a device is unlocked, all they mean is that you can use any sim card of your choice. To be able to flash another rom you need to CID unlock it. For the Orbit/Artemis family we only have imeicheck selling the program for unlocking cid.
My advice would be to look for the orbit rom on ftp. If it does not work, check with imeicheck if their program works when device is in bootloader mode, and pay them and download the specific application for your device. Good luck
I had a problem with my Orbit when I tried to change the Rom to the PDAMobiz one. I ended up recovering it by...
1 - Hard Reseting it.
2 - Connecting it up to the PC then running C3v2Unlock note v2 from the the IMEICheck site. This made the screen on the Orbit go bright white.
3 - Downloading the the Rom listed in this thread and following the instructions with in the same
It means that my Orbit is seen as a HTC P3300 but it feels quicker. You do need the UNL file from IMEICheck to keep it unlocked. But it worked for me.
Yes I tried everything in bootloader mode,
the C3V2 Unlock program launched but after detecting the device, it says my device is corrupted with a kind message "[probably by your fault]" ;-)
So guys, everyone who's trying to upgrade : CID UNLOCK YOUR PHONE BEFORE DOING ANYTHING, and carefully read the (excellent) tuto.
FYI, here's the discussion I had with Imeichek guys :
------------------------------------------------------------
Hi,
I'm a little desperate and I hope you'll be able to help me...
I recently bought an 02 Orbit that was supposed to be unlocked (I didn't know the difference between SIM lock and CID lock)
I understood, too late, that I should have ask for my UNL file prior to do this stupid "direct upgrade" I did...
Here are the facts :
1- I didn't follow the instructions found on http://forum.xda-developers.com that explained how to order the UNL file and Unlock the device unlocked
2- I downloaded a new ROM (PDAMobiz_Dopod_P800W_AKU301_v1.1.0_Lite.exe)
3- I unpacked it and double-clicked on UpgradeRom_P800W.bat
4- A dos installation routine the started, then when asked, I performed a hard reset by pressing the softkeys + stylus reset.
now I"m stuck on the O2 logo, with some red informations written :
IPL 1.25.0001
SPL 1.25.0000
GSM 02.67.90
OS 1.28.0.0
but nothing else, the device don't go further
I've tried to install another ROM like ART_HTCWWE_11240501_026790_WWE_Ship, but when I launch ROMUpdateUtility.exe it says that no device connected.
I managed to enter the bootloader but my device is still not be recognised by my computer (not connected message). I tried your C3v2Unlock tool but it says the same : NOT CONNECTED
So please, if you have any information or procedure I could try to fix my device, I would really, really, appreciate, especially after my 30€ contribution ;-)
Best regards
---------------------------------------
2007/2/17, [email protected] <[email protected]>:
Hello,
NO PANIC. You can fix the device. You have to find the CORRECT / a matching ROM for your device. For this you have to know what ORIGINAL phone it is (O2 Xda Orbit UK?)
Tell us what device it is and we try to assist you in fixing it.
Regards,
IMEI-CHECK Team
-----------------------------------------------
Thanks for your fast answer!
Yes it's an original phone, a brand new O2 Xda ORBIT, in box
Regards
Thomas
----------------------------------------------
Hello,
the language is important. Is it UK version?
Regards,
IMEI-CHECK Team
-----------------------------------------------
yes it's a UK version
-----------------------------------------------
Hello,
hmm, sorry to tell you but for the UK version there is no official ROM update available right now.
All you can to do fix it NOW is to send it to repair (service center).
For our customers we offer to fix the device for free (you only have to pay for shipping costs in both directions). We are located next to Glasgow UK. In case you are interested let us know.
Regards,
IMEI-CHECK Team
-------------------------------------------------
Ok,
I guess I don't have any other choice.
Wich ROM will you install if there's no official O2 Rom ?
What is the procedure, what's your adress, and how much will cost the return ?
Thanks a lot
Thomas
-----------------------------------------------------
Hello,
- we can install any ROM of your choice (it only needs to exist)
- we also will unlock the device and you can install ANY ROM you life afterwards
- the device needs to be opnened to use some special hardware to access the flash chip directly
- shipping back to (UK/EU) with INSURED Royal Mail is apx. (7 GBP/15GBP) depends where you are located.
Regards,
IMEI-CHECK Team
---------------------------------------------------------
ok thank you,
but will you be able to flash an O2 Xda Orbit with the french ROM that comes with the (Artemis) HTC P3300 sold in France ? this is exactly the same machine.
Regards
---------------------------------------------------------
Hello,
yes we can flash ANY available ROM to it.
Regards,
IMEI-CHECK Team
----------------------------------------------------------
here I am,
I guess there is nothing else to do.
First I want to thank you all for trying to help, then thanks to IMeicheck, they replied very fast and found a solution, even if I won't hae my Orbit for several weeks.
2- I downloaded a new ROM (PDAMobiz_Dopod_P800W_AKU301_v1.1.0_Lite.exe)
3- I unpacked it and double-clicked on UpgradeRom_P800W.bat
Click to expand...
Click to collapse
Maybe you should not have unpacked the file Just clicking on the file icon starts the procedure, which does some checks before actual upgrade starts.
I have switched so many times between the pdamobiz roms and the HTC one so many times I've even lost count
It's been easy for you... because your phone was CID unlocked ;-)
Well i had HTC ROM and now i have pdamobiz... That means that my artemis is cid unlocked???
my orbit is stuck on boot screen exactly as manples'. i tried to flash pdamobiz custom ROM. i can enter bootloader. can u tell me plz to what change "BsaD5SeoA" with "IMEICHECK save exe file" from imeicheck i've got c3v2unlock.exe & unl file. i tried flash it tru sd card-nothing. I've got o2orebit (ARTE200) please hlp
Psrejic, does your Orbit work again? I have the same problem. Can't get passed the splash screen because I flashed it with the PDAmobiz rom.
Only way to go is thrue bootloader. Did the SD flash work for you?
Same problem here Waiting for any solution ...
Only solution so far is imei-check service, witch will cost you: Price of sending to them: (UK) Then 20£+15£(aprox) to pay them for unlocking and repairing + sending back.
That's what I've done,
I received an email where they confirmed the reception of my device and that they flashed it with a new Rom. My device is supposed to work, it's great ! can't wait to try it.
Hi manples ...
You send it to imei-chek?
My Orbit works again! ... but not with a software solution.
I returned the phone to the O2 shop and they gave me a new one immediately. I didn't mention my PDAmobiz Rom upgrade offcourse.
It isn't the nicest way to deal with the problem, but when o2 flashes the rom on the phone they can sell it again.
Then I did the Imei-check solution. Worked and flashed the dopod rom on it.
hi to all yesterday I was your siimilar problem (I've try to install teh powermap rom...) so my Orbit O2 (original german rom) still only in boot screen, today I've try to install this magic rom:
art_tmouk_11311001_024990_wwe_ship.rar
I've press the comm manager button + power button + soft reset and my orbit it's enter in bootmanager mode so, i've install the TMobile UK rom (I was the O2 german rom...)
only in this mode my orbit work again.
bye
xda orbit stuck
i flashed my xda o2 orbir german rom with PDAMobiz_Dopod_P800W_AKU301_v1.1.2 and now it wont start at all i tryed to enter bootloader but i cant ( voice key and reset ) its stuck at o2 logo and :
IPL 3.04.0001
SPL 3.04.0000
GSM 02.00.90
OS 1.20.0.0
DOSE ANYBODY have a solution ? please help me !
keep up the good work ! thanks
Hi,
Does anyone knows a method for repairing my old P3300.
The problem is i've tried to upgrade to wm6 and something went wrong,
ATM i only have a screen with the Tmobile logo,
I can open the bootloader, but if i load the bootloader and try to run the official rom update i get the error 122 cannot connect to device.
If i'm in the bootloader and try to start mtty, it all goes as it is supposed to go
I can see the phone in mtty and can get it into flash mode when i enter the bootloader password.
Even when the phone is in this mode the official upgrade won't see the device.
So my question: is there a way to flash/upgrade the rom from mtty?
If yes what are the commands for it in mtty.
If not does anybody know an other solution?
Btw it's a sim unlocked and Cid unlocked P3300 From the Netherlands Tmobile.
IPL 1.13.0001
SPL 1.13.0000
GSM 02.49.90
OS 3.4.0.0
Thanks
Janus
Same here, I think we need the original T-Mobile rom.
RaZoR X said:
Same here, I think we need the original T-Mobile rom.
Click to expand...
Click to collapse
sounds like you did't run the USPL before you burned your Rom, try and do a search on this in the forum, there are plenty of fixes to get your phones up and running again.
another tip, look at the wiki and download Tmobile UK/Ger version, that should do the trick at least to get your phone running, then make sure you do the USPL before you brick it again.
neilhhardy said:
sounds like you did't run the USPL before you burned your Rom, try and do a search on this in the forum, there are plenty of fixes to get your phones up and running again.
another tip, look at the wiki and download Tmobile UK/Ger version, that should do the trick at least to get your phone running, then make sure you do the USPL before you brick it again.
Click to expand...
Click to collapse
I did ran the USPL.
I took a look @ the wiki, but I think those files (all of them are less then 100k) are theme files.
"T-Mobile_NL_MDA_Compact_III_1.13.114.1_NLD_ExtROM"
IPL: 3.13.0001
SPL: 3.13.0000
The USB is working
With the "PDA Phone ROM Update Utility 3.6.3.1." from HTC I tried to get the MDA functional again.
In the Verify the ROM you want to update window it says this:
From:
Image version: -blank-
To
Image version 3.13.405.1
But after 2% sometimes 7%, it says this: "Error [244]:Invaild model ID".
So maybe the USPL didn't went well.
At the Artemis_Upgrades section of the wiki there isn't a T-Mobile file to download. The language doesn't matter to me.
Which device are you guys trying to flash with a new ROM, if its a UK T-Mobile device its not got the WiFi hardware so don't go putting a ROM on the device that expects WiFi support, T-Mobile Artemis units from Holland did have WiFi built in as does the true HTC P3300 unit, the UK T-Mobile device does not - Mike
RaZoR X said:
I did ran the USPL.
I took a look @ the wiki, but I think those files (all of them are less then 100k) are theme files.
"T-Mobile_NL_MDA_Compact_III_1.13.114.1_NLD_ExtROM"
IPL: 3.13.0001
SPL: 3.13.0000
The USB is working
With the "PDA Phone ROM Update Utility 3.6.3.1." from HTC I tried to get the MDA functional again.
In the Verify the ROM you want to update window it says this:
From:
Image version: -blank-
To
Image version 3.13.405.1
But after 2% sometimes 7%, it says this: "Error [244]:Invaild model ID".
So maybe the USPL didn't went well.
At the Artemis_Upgrades section of the wiki there isn't a T-Mobile file to download. The language doesn't matter to me.
Click to expand...
Click to collapse
ok hear'd this one many times before, your running vista >?
try and search the forum, there is a fix for this then your phone.
@Mike it's the "Dutch" version with indeed WiFi
@Neilhhardy
No, I'm not running Windows Vista at the moment.
Me too have the same problem - flash allways stop at 2% , also can`t flash radio - stop at 73-75% - any idea?
the phone is original HTC (have Wi-Fi and not branded) - never CID locked go to bootloader without any problems but can`t flasing - I think case problem is standart HTC flasher exe - for early models have different flasher software - I have Jaf WM but Jaf WM do not support Artemis - did have released other soft that alow flashing Artemis?
P.S - I thing cause right solution is to flash your device with original version - the OEM version that was instaled by factory will fix the problem
this worked for me on a unlocked mda compact 3
format your memory card first with your pc then copy the rom file (nbh)to your memorycard and rename it to ARTEIMG.nbh
start bootloader and follow the instructions.
http://wiki.xda-developers.com/index..._Card_Flashing
rom i used http://makus.folijka.pl/OrbitO2UK.rar
I found the right solution and fix my phone stop at 2% is hapenind when the phone was flashed before cid unlock (bricked) and can be restored ONLY with ORIGINAL version for that phone
1. go to www.htc.com then go to support area and register your headset by they own htc serial number!!! this is most important step!
2. download update soft - the supportsite know what exactly is rirgt version and language for your pda
3. Flash your phone and will be alive
4. USPL and make after that what you want with your headset
TESTED and WORKED for dead phones(but phone must go to the bootloader)
I did a reset with the rec, pwrbutton and resetbutton. And now he's up and running agian with WM6 Haha
I tried to unlock the device with the AthenaUnlocker, but I got this error:
0x0, 0x100000, SPL-verify.nb
I think I killed him lol
ppl said:
I found the right solution and fix my phone stop at 2% is hapenind when the phone was flashed before cid unlock (bricked) and can be restored ONLY with ORIGINAL version for that phone
1. go to www.htc.com then go to support area and register your headset by they own htc serial number!!! this is most important step!
2. download update soft - the supportsite know what exactly is rirgt version and language for your pda
3. Flash your phone and will be alive
4. USPL and make after that what you want with your headset
TESTED and WORKED for dead phones(but phone must go to the bootloader)
Click to expand...
Click to collapse
this may had worked for you but at the HTC website I get the error that my phone is not branded. true it's a tmobile phone...
can you give me the serial number you entered? if you dont trust it you may make the last 3 digits a X
thanks
Janus
Hello Buds,
I've upgrade my p 3300 a few weeks ago with Artemis_touch_1.0_WWE_rapid
IPL 1.14.0001
SPL 1.14.000
GSM 02.67.90
OS 3.7.0.0
After some days a freeze and soft reset, I made a hard reset, and re-use the upgrade soft ware.
Now its completly block on the boot page with HTC.
I use RUU(in( Artemis_touch_1.0_WWE_rapid) in the Bootloader but it run but after 3% : error 270
If a use a newer RUU ( Release_Aje_fr_1.90Full_YuanYuan) : error 260
please help me I completly lost !
Trux 13
HTC P3300IPL 1.14.0001
SPL 1.14.000
GSM 02.67.90
OS 3.7.0.0
I had almost the same problem. I intented to change my ROM with an WM6 but it faild and the PDA is some kind dead it freezes in the boot screen. is there some tool to change the rom to an original HTC rom or thre is no help. I hope somebady can help me. the version of the ROM that apears on the screen is:
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 4.0.0.0
I've tried to :
Hello...
In bootloader run USPL
It run, to 0% >> to 100% but right after : error 270
Still block...
Trux 13
hmm i don`t know how i can get the device to boot loader mode can u tell me how
Bootloader
Go in ths Thread :
http://forum.xda-developers.com/showthread.php?t=306880
Trux13
hi i solved my problem i used one spanish version of the WM6 for P3300 and it works if u want hire is the link http://www.megaupload.com/es/?d=YZOQEF4H
u can install it and then change to one on english its what i will do today and i saw how to enter in 3 color bootloader mode ON/OFF boton + VOCAL + RESTART then holding the ON/OFF + VOCAL
Stillnot working
I tried your *.exe file but not working
Trux
me too . always the error
ipl 1,14,0001
spl 1,14,0000
g 02 67 90
os 1,14,00
i ll be crzy! jesus! someone help me!
how to run the uspl on this tm phone ?
Has anybody solved the problem? I have exactly same errors and can't do anything
Try This:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
i tried this already. Invalid certificate any other ideas ?
woojtekr said:
i tried this already. Invalid certificate any other ideas ?
Click to expand...
Click to collapse
Hi
if you need still help GG9735272
the only solution !!!!
woojtekr said:
Has anybody solved the problem? I have exactly same errors and can't do anything
Click to expand...
Click to collapse
to everybody who is stuck at HTC screen. The only,and i mean the ONLY way to fix this is to find the original rom for your provider !!! belive me,i`ve tried every possible other way.
SD Card Flashing wont work coz your devices are probably CID Locked,so it goes only to 3% flashing and restarts.Finally I found original o2 ROM (German) and it worked like a charm Even the original o2 (English) ROM did NOT work,it had to be the German one,coz probably the device came with German ROM originally !!!.
So my suggestion is,stop trying to flash it with different ROM`s and spend some time finding original ROM from your provider and it has to be the same language as your provider. even if it`s WM6 and your device was originally was WM5,as long as its from your provider and same language it should flash with no problem.I spent 2 weeks to find this out ))
Good Luck to everybody ))
savich said:
to everybody who is stuck at HTC screen. The only,and i mean the ONLY way to fix this is to find the original rom for your provider !!! belive me,i`ve tried every possible other way.
SD Card Flashing wont work coz your devices are probably CID Locked,so it goes only to 3% flashing and restarts.Finally I found original o2 ROM (German) and it worked like a charm Even the original o2 (English) ROM did NOT work,it had to be the German one,coz probably the device came with German ROM originally !!!.
So my suggestion is,stop trying to flash it with different ROM`s and spend some time finding original ROM from your provider and it has to be the same language as your provider. even if it`s WM6 and your device was originally was WM5,as long as its from your provider and same language it should flash with no problem.I spent 2 weeks to find this out ))
Good Luck to everybody ))
Click to expand...
Click to collapse
I have the same problem and I've come to believe that this is the only solution. Just one thing: I didn't back up ROM before I tried to flash (talk about a noob mistake).
So, I ask, I plead, I beg... can anyone tell me where to get an original Orange France ROM for the Artemis (SPV M650)?
To my knowlegde you cant backup the rom from your device. whenever you change your rom, use the USPL tool. It is a golden rule until something better is made.
Here are some tips:
First make sure you have a original factory rom from your provider/brand/etc.
Check with a soft reset if code: SPL 1.11000 appears on the the boot screen. (then it is CID unlocked) Any other number and it is locked so you have to USPL first before you change to any custom rom.
If you flash a factory rom then the SPL resets to a non SPL 1.1100 number again. Use USPL to CID unlock again.
Also avoid Vista (especially 64bit) to use the USPL tool. Do it on a windows XP machine. Also there reports of glitches in the usb connection and active sync when doing upgrades or USPL. So keep you system as clean as possible. Dont use a USB hub and disconnect any other usb devices just to make sure.
Also remove your SD / SDHC card before doing a upgrade.
Sometimes the new rom misses some stuff when flashing. When this happens just flash the rom again. But first make sure if its still CID unlocked by soft reseting and check if SPL 1.1100 else use USPL first.
Even if you did all that, there still can be things that can go wrong. So if you absolutely confident to do a custom rom then do it. Otherwise use original upgrades from your provider
brim
help i breaked my htc p3300
jai lereur 270 jai essaiyer tous les rom rien ne marche ::
p3300 work again
p3300 movistar work again
I downloaded the tyler wing kit and copied the cabs over to the phone.. i installed the cabs and reset the phone and now it is loocked on the boot menu as follows :
(htc background)
IPL 5.04.0002
SPL 5.04.0000
GSM 02.79.90
OS 5.4.0.0
AND DOES NOTHING...
perform hard rest and fat format comes up and returns to same screen
removed battery and still the same .
I tried applyinf wm6 ruu since this happens, but will not apply as unable to sync to apply....
is it a brick now ? or is there anything else i can do to recover ?
hold fire on that for now... i managed to figure out the bootloader mode and am currently uploding a rom ...
looking to upgrade to wm6 with the touchflo interface... any hints would help ! .. ps the wm6 rom wouldnt load becasue of a vendor id mismatch ??
ok,,, managed it get it bac up and running with :
RUU_Herald_HTC_WWE_5.4.405.1_4.1.13.34_02.79.90_Ship.exe
tried the tyler wing kit again and locks on boot after first 3 apps installed any ideas or links to getting wm6 with touch flo installed ? ( htc p4350)
montythegod said:
ok,,, managed it get it bac up and running with :
RUU_Herald_HTC_WWE_5.4.405.1_4.1.13.34_02.79.90_Ship.exe
tried the tyler wing kit again and locks on boot after first 3 apps installed any ideas or links to getting wm6 with touch flo installed ? ( htc p4350)
Click to expand...
Click to collapse
What is the Tyler wing kit? Never heard of it...
found it here http://forum.xda-developers.com/showthread.php?t=327046
(sticky on main page
I managed to get wm6.1 rom on the phone now tho