Related
I am sure you used to be able to do it on the universal but now it seems I cant !!! does anyone know how !!!
I doubt you can send them, but you can enable tones in the phone control panel (I think it's there, but somewhere near there).
That just makes the phone keypad beep lyrical.
V
my old nokias can do it and so can my GF's samsung D500 !! a very useful option when using 3rd party dialers, I dont understand why this phone cant do it !!!
I always use this feature to send over the calling card PIN number and the destination number so even though I make an international call using phone card I do not need to puch the PIN etc manually. Just record the number into the contacts and use some delays. It works.
lie_ui said:
I always use this feature to send over the calling card PIN number and the destination number so even though I make an international call using phone card I do not need to puch the PIN etc manually. Just record the number into the contacts and use some delays. It works.
Click to expand...
Click to collapse
I know what you mean but that means I need to change all the international numbers stored in my phone, it would be easier if I could just call the number and then choose the number out of my contacts and send tones !!!
i have the same issue. i use an international caller to dial out to america and on my nokia i would just send the tones of the numbers i wanted to dial. now i have to write them down so i can punch them back into the xda. shame
Assuming I understand your problem correctly, it sounds like the problem is with your calling card provider and not your phone. The Universal, like any other phone, ought to send DTMF tones through in-band audio -- pretty standard stuff. I've tested this with my calling card provider and I'm able to put in my PIN code through DTMF without any problem.
I think that what these guys are describing is the ability, whilst on a call, to say "Send DTMF" and then choose a number from your contacts. This way, you can store your calling card number in one phonebook entry and all your other contacts as normal, then you choose the calling card to dial and then "send" the number for the other contact. However, you usually need to append a "#" with these services and the number needs the international prefix (so USA becomes "001" instead of "+1"). I generally just store two numbers against each name - one normal and one with integrated calling card.
I don't think anyone is saying that they can't manually key in the number mid-call.
That's exactly right, Melty.
Has anyone found a utility or a way to automatically dial numbers using a calling card? This is a rather convenient feature in my previous (non-WM5) cell phone that allowed me to import my corporate phone numbers and then use automatic calling card to dial them without editing hundreds of entries in the phone book.
I have noticed the "Callingcard" code sample at MSDN, however, there does not seem to be a compiled binary available anywhere and I do not have the development environment available.
Any help or tips appreciated.
Ihave been using this one
It is one of the importat things for me
so I use Program called "Long Distance Dialer (Pocket PC Phone) 1.3"
it works on WM2003, WM2003SE and I am runing it right now on WM2005
http://www.pocketgear.com/software_detail.asp?id=12595
good luck
DNO
Thanks! I did not realize it even runs on WM5. However, it does not see to go past dialing the access number - goes to reorder / busy tone right after. Is there a trick / fix to it?
I am using it on HTC Wizard
I never had that kind of problem
I don't know how to help you
This is my settings
Name: My card name
Acces#: my number (only numeric )
Dial Seq : PIN/Destination
Wait: 1Sec Pin : My pin
Wait 1 Sec Destination
then I go to Contacts I right click on the name I want to dial , it gives me optioon >> Dial using : then Name of my calling card .
When I click on that it gives me list of the phone numbers unther that name .
Since I call from USA I do need to select option << Add 011 before number >> but I do not do it because I added 011 to all phone numbers that I call with the card , in the Contacts
I hope this will help.
Good luck
DNO
I installed Long Distance Dialer 1.5 on my PPC. I like it so much that I want to register ($4.99). However 1.5 cannot be purchased anywhere anymore. Did anyone manage to purchase a registration key for 1.5? Or alternatively are 1.3 registration keys inter-changeable with 1.5?
This seems like a great piece of software, but it won't seem to accept pins less than 4 numbers. I have all my number listed with the country code first, so I need to add 00 to call them. In the past, I've configured my calling card feature to use 00 as the pin, which works great, but I can't get this to do it and I don't want to manually add 00 to all my numbers!
Many thanks for any help,
Paul
The link is to version 1.3. What you need is version 1.5. A quick Google will give you two or three sources.
1.5 has no limitations, but has an annoying trial notice pop-up each time you use it. Where can I purchase a registration key?
Thanks for the reply. I've downloaded v1.5, but it still won't let me enter a pin of less than 4 digits. Any thoughts?
Many thanks,
Paul
Solved the problem. In v1.5 you can put spaces as well, so, even though it needs at least 4 characters, I can put two spaces and then the two zeros.
Best,
P
Interesting - I was trying to solve my problem with the software dialing only the calling card access number. I defined an address book entry with the whole number with pauses - and still only the access number gets dialed. The card I use follows the "Number followed by PIN" model with a second dial tone after you dial the access number and a third one after the called number. Any ideas what could be causing the issue? Could it be that the Wizard does not recognize that the call has been completed after it dials the access number?
free and the best calling card dialing software
this is reply to betstu2004 request i.e compiled binary from msdn betstu2004 mentioned about
its in cab format and is attached for downloading.
here is the procedure for installing and using it:
1)copy the cab file in ppc and install it
2)then using any registry editor we have to edit the values of number to be dialled and the pin number of the calling card,to do that
open registry editor
go to:
hkey_current_user
then software
then microsoft
then calling card
in this option you have to edit two entries
1st is Number which is your calling card number
2nd is Pin which is your pin number
save the changes
then to use the software
go to contacts
then
with stylus touch and hold the contact(international) you want to dial
you will see an option
call mobile using calling card
click it
and ppc will start dialling using calling card software with stored calling card number and pin
once the card is finished you can input the values of number if different from previous one and pin again
in some cases the new number and pin will only be saved in the registry after soft reseting the phone
you can even adjust the pause time which is 2 sec by default
this software is working perfectly on my xda exec and i hope you all will love it
cheers
My email to the author (VSOFTCODE) of LDD bounced. Looks like I will have to remove it after the trial expires.
Edit: I just managed to purchase a licence through Handango after all.
----->chaniana
Thanks works fine!!
chaniana - BIG thanks - it works flowlessly.
Now - if I could only get it to dial the number before the PIN!
reg key
Well I know this is not a warez site but
would it be wrong if I give out the reg code ??
I think not ,because the software no longer supported by the developer.
what you think ???
One more thing !!
I have Version 1.3 which I bought from www.pockeatgear.com
where did you find v1.5 ???
Let me know
DNO
this is cool....
chaniana , i have been looking for something like this for a while... i have 2003 not 2005 to be able to complie or change this...
I am just migrating form treo 650 and am missing a program TakePhone. what it did it let me create rule
e.g. any number starting with a string it will use a calling card so i could set +44 use a calling card x
that way when i disl a number it will intercept the call an see the first few digits, if +44 it will dialthe calling card and wait for me to hit a button to enter a pin then eait for another button to dial the number, all in a few strokes i was dialing international and never had to change my contacts. when i was there in UK all i do is disabke the rule and voila i am in business...
see if u can do this
i did something similar in VS2003 creating from scratch an app that would list the contacts and i enter a ph and pin in 2 seperate textboxes and hit dial, got it to make a call to the 1800# but could not figure out how to dial the rest automatically so i am stuck
Long Distance Dialer 1.5 at handango.com.
Just pay the 5 bucks, it may inspire others to create affordable useful software!
This software doesn't work with PocketInformant. Any solution ?
I installed Long Distance Dialer 1.5 (Trial), entered Calling card (access#, PIN)
I can see new menu item when I right click "contact", but when I select "Dial CCard" NOTHING happe! No call started.
I'm using Wizard.
Hi
I am not able to see any context menu once I tried using by stylus
I am on WM6.1
Is it still usable
cheers
chaniana said:
this is reply to betstu2004 request i.e compiled binary from msdn betstu2004 mentioned about
its in cab format and is attached for downloading.
here is the procedure for installing and using it:
1)copy the cab file in ppc and install it
2)then using any registry editor we have to edit the values of number to be dialled and the pin number of the calling card,to do that
open registry editor
go to:
hkey_current_user
then software
then microsoft
then calling card
in this option you have to edit two entries
1st is Number which is your calling card number
2nd is Pin which is your pin number
save the changes
then to use the software
go to contacts
then
with stylus touch and hold the contact(international) you want to dial
you will see an option
call mobile using calling card
click it
and ppc will start dialling using calling card software with stored calling card number and pin
once the card is finished you can input the values of number if different from previous one and pin again
in some cases the new number and pin will only be saved in the registry after soft reseting the phone
you can even adjust the pause time which is 2 sec by default
this software is working perfectly on my xda exec and i hope you all will love it
cheers
Click to expand...
Click to collapse
I don't seem to be able to find a way to more easily make calling card calls. In other cell phones, you can set it up such that both calling card entries and phone numbers are within the phone to dial. I don't see how to do it on the Wizard.
Can someone shed some light?
Thanksk,
Setup calling cards
Hi,
You can program your calling card no, pin as follows:
phonenumber#,calling card#,pin#
Put the comma "," between the numbers which makes the phone pause for about 2-3 seconds before dialing the next sequence of numbers.
HTH
--
NB
Re: Setup calling cards
nextbond said:
Hi,
You can program your calling card no, pin as follows:
phonenumber#,calling card#,pin#
Put the comma "," between the numbers which makes the phone pause for about 2-3 seconds before dialing the next sequence of numbers.
HTH
--
NB
Click to expand...
Click to collapse
I travel between places. When I am in different countries, I use different calling cards that is local to that country so I prefer not to embed calling cards in all the contacts' phone numbers.
I've used Sony Ericsson and Motorola cell phones. Both of them allow me to program a separate calling card number and use some special mechanism to string the contact's number with the calling card number. This is the biggest missing part on Wizard, I think.
Thanks,
CJ
I use Long Distance Dialer
http://www.pocketgear.com/software_detail.asp?id=12595
dmitryfink said:
I use Long Distance Dialer
http://www.pocketgear.com/software_detail.asp?id=12595
Click to expand...
Click to collapse
There is a newer version 1.5 at http://www.pdatopsoft.com/download/?pid=3001&
Hi @ all,
I have a question or request. First let me explaine the situation.
I use justVoip.com for calling German Cells cheaper and the USA for free. I call justVoips Landline for free (because I have a landline-flat) and they forward the call to the desired number. I used to just save their number before the contacts number seperatet by a "P" (pause): 08912345P0172123456
When receiving calls my Motorola would still recognize the Call-id, also with the voip number in front of it. But my X1 now doesnt recognize calls with their number inserted...
So my question is... either is there a way to have two seperate phone books running parallel or is there maybe a software that always asks if the preselection should be added when making a call??
Or a nother solution I didnt think of yet..
Hope this wasn't to complicated and you kinda now what i mean...
thanks..
Danny
anyone know if there is any way to assign a contact to use a particular Sim with out switching using the Sim manager, when yo dial a number you get the option to select the Sim to use but the contact seem to only use the selected Sim ATM i hang up and you can the redial and select the Sim ( i have my home Sim and works Sim in the phone )
I have tried Samsung but the are unhelpful as i am using the phone in the UK and its not supported in this region,
If anyone in a region where the dual Sim version is supported has 5 mins to chat to samsung via there web chat can ask the question if there is any way to set a contact to dial using sim1 and another contact to use sim2 the ask them to request the feature be added via there dev team it may get added or i may just have to go back to LG as they have better call control..
thanks in advance
copex said:
anyone know if there is any way to assign a contact to use a particular Sim with out switching using the Sim manager, when yo dial a number you get the option to select the Sim to use but the contact seem to only use the selected Sim ATM i hang up and you can the redial and select the Sim ( i have my home Sim and works Sim in the phone )
I have tried Samsung but the are unhelpful as i am using the phone in the UK and its not supported in this region,
If anyone in a region where the dual Sim version is supported has 5 mins to chat to samsung via there web chat can ask the question if there is any way to set a contact to dial using sim1 and another contact to use sim2 the ask them to request the feature be added via there dev team it may get added or i may just have to go back to LG as they have better call control..
thanks in advance
Click to expand...
Click to collapse
Hi,
I also have a G935FD and indeed, you're right I haven't found anything to be able to choose from which sim card you want to call when calling via contacts. It works only when you dial from the touchpad...
Complaining at Samsung might help to implement that process in the upcoming updates.
copex said:
anyone know if there is any way to assign a contact to use a particular Sim with out switching using the Sim manager, when yo dial a number you get the option to select the Sim to use but the contact seem to only use the selected Sim ATM i hang up and you can the redial and select the Sim ( i have my home Sim and works Sim in the phone )
I have tried Samsung but the are unhelpful as i am using the phone in the UK and its not supported in this region,
If anyone in a region where the dual Sim version is supported has 5 mins to chat to samsung via there web chat can ask the question if there is any way to set a contact to dial using sim1 and another contact to use sim2 the ask them to request the feature be added via there dev team it may get added or i may just have to go back to LG as they have better call control..
thanks in advance
Click to expand...
Click to collapse
Settings>SIM card manager>Prefered SIM Card and set your default sim for various services
victoradjei said:
Settings>SIM card manager>Prefered SIM Card and set your default sim for various services
Click to expand...
Click to collapse
thanks but i would still have to change the default every time i called a contact
Just found a new option that will allow you to select "Always Ask" its not perfect but it helps
copex said:
I have tried Samsung but the are unhelpful as i am using the phone in the UK and its not supported in this region,
If anyone in a region where the dual Sim version is supported has 5 mins to chat to samsung via there web chat can ask the question if there is any way to set a contact to dial using sim1 and another contact to use sim2 the ask them to request the feature be added via there dev team it may get added or i may just have to go back to LG as they have better call control..
thanks in advance
Click to expand...
Click to collapse
This is exactly what I found bit annoying, you couldn't set preference per number as which SIM to use out of the box (by not using any app.. just plain OS based solution), I couldn't find any. Tried asking on this & other forums. http://forum.xda-developers.com/s7-edge/help/sgs7-changes-marshmallow-t3353208
On the play store, found couple of paid apps that were doing the job, but one of them was not working on v6.0.1 (app creator was still in process of upgrading app to work on MM v6.0.1), another app gives you 7 days of free usage but costed £5 after that. I also tried to create a solution using Tasker, but it required a plugin which was first app that I mentioned was still under upgrade.
Frustrated with these problems, I decided to take control myself & now I'm in the process of developing an app that will exactly address the number-SIM preference. I found that Android has exposed a multi SIM API in version 5.1, but it's so poorly documented that I got really really angry about lack of information. Somehow I managed to build a workable copy of app. In this app you can specify rules based on Regular Expression number matching as which SIM to use if the dialed number matches regular expression specified. There is also an auto learning feature, where it will remember SIM for a number to dial.
As I said, I'm still in the process of developing this app, it's not professionally perfect but definitely does the job for now.. (It takes lot of time as I'm not an app developer & devoting time is a problem ), there are many features I want to implement in this app, but let's see when I find time. It's working perfectly on my S7E dual sim (I can't guarantee that it will work on any other device - although it should as app is built using androind 5.1 API -- I haven't tested on any other device).
If you need a copy of APK, do PM me & I'll send you one.. I've also posted same message here.
i will be interested to see the final version, ask always is working as a temporary fix.
preferred sim not working
for me if i click on a contact to call someone then it asks call from sim1 or sim 2 but i already chooses sim2 as preference. if i use swipe it is going from sim 2.
victoradjei said:
Settings>SIM card manager>Prefered SIM Card and set your default sim for various services
Click to expand...
Click to collapse