Related
Hi i have 2 part question my phone is an htc 8125 cingular sim card unlocked phone it has windows mobile 5 on it and i have the IPL 1.05, SPL.3.08 on it.
I did this but installing the IPL_SPL_3.08 rom. Anyways Im trying to get it back to IPL 1.05, and SPL 1.05 by installing the button rom and i seen the beer screen and it loads up to windows mobile 5 but keeps staying at IPL 1.05, and SPL 3.08 is there away to get it back to 1.05,1.05. I tried a few methods but aint working. Would keep reflashing a few times with the button roms get it back to 1.05,1.05. I tried with, newromupdateutility_wizard_noid. and didnt work i tried with rom update and didnt work. When a rom loads up and gets stuck at 99% and then i get a message with activesync saying lost communication error message whats does that mean and it saying try restore.
Also can windows mobile 6 with touch flo install on this phone or no. I was tring to do that with but all i got was it going back to windows mobile 5 and doesnt upgrade to wm6. Do i first need it to get it back to 1.05,1.05 using the button rom then use ,lokiwiz02b to do the unlocking(mind you my phone is all ready sim unlocked). and then flash a t-mobile or cingualr rom and then do the update with a windows mobile6 rom.
Whats a good windows mobile 6 with touch flo that works good on this phone can u maybe post a link
thanks for the help
deleted for inaccurate information
First,you shud have CID unlocked the phone prior to upgrading to 3.08 bootloaders,cuz it becomes very difficult and frustrating to downgrade from 3.08 to 1.xx.Now the only way is to first try to downgrade to 2.xx by flashing the official carrier's rom and when completed downgrade to 1.xx through Button's 1.05.You can only CID unlock the phone,if its 1.xx,which you already know.
Secondly,it'll only upgrade to wm6 if its cid unlocked.Try to flash ipl/spl 3.08 again and make both ipl/spl 3.08 first and then downgrade to 2.xx by flashing the official stock rom,it might work.
Cheers!
i have rogers htc touch, after trying unlocking using ELF USPL , when i power on only see HTC Logo and then it goes off, i try loading new rom but still same problem . Please help
What is your IPL and SPL?
IPL is 2.21.0002
and
SPL 1.11.0000
I had the same problem...took me 3 hours to figure it out..
1. on Bootloader, re-install a ROM that works (go back to WM6 or WM6.1)
2. when it working, install USLP 1.11
3. DO NOT RESET AFTER...
4. install USLP 3.14
5. then you can install any WM6.5 ROM
For some reasons, the Rogers Touch has some difficulties to upgrade directly, even if it's unlocked...
Good luck
Michel
michel-2000 said:
I had the same problem...took me 3 hours to figure it out..
1. on Bootloader, re-install a ROM that works (go back to WM6 or WM6.1)
2. when it working, install USLP 1.11
3. DO NOT RESET AFTER...
4. install USLP 3.14
5. then you can install any WM6.5 ROM
For some reasons, the Rogers Touch has some difficulties to upgrade directly, even if it's unlocked...
Good luck
Michel
Click to expand...
Click to collapse
Thats a great tip to the community, I will refer back to your guide if I met with anyone with troubles using Rogers.
...thanks...
But, after reading a lot yesterday, seems that the USLP 3.14 is a ''battery eater''...
I'm testing it now..I will see in a couple of days if it is the case!
So far, it looks like it's using approx 2% of the battery per hour...
Definitely, you should always use 3.10.
I had a bad experience with 3.14, it takes up half of my battery after 5 hours of almost no usage.
i'm confused. .... i also have a rogers htc touch as well and i want to flash a custom rom onto it.
(my IPL: 2.21.0002 and SPL: 2.21.0000)
First, i know it has to be CID unlocked... using >> Elf 1.11 USPL ?
Can i use HARDspl ?? What is the difference between USPL and Hard uspl ??
Because i read something about ..... " HardSPL : This modified bootloader allows a much safer flashing process to take place since it reduces the chance of permenently bricking your device. It also removes the need to CID Unlock the device since it ALWAYS reports SuperCID when flashing. "
After a CID unlock and soft reset, the phone will reboot into the old ROM (Rogers, in my case) if i have not began flashing a new rom ??
Some advice please... thanks!
Use the guide written on 4th post.
Its located on this thread
Cheers.
Hello guys, I've got a p3300 which I can't update to a WM 6.1. It's the factory's 6.0. It's originally simfree so I dunno if I need to go through the USPL.
The thing is that it gives me 270 Corrupted image error.
As I thought that being simfree originally, didn't need to do CID unlock, I tried to flash a cooked ROM with no success whatsoever.
Any ideas?
Kind regards,
JamworkS.
DONT try to install any rom untill you flash ''uspl cmon''!
you might brick the O2xdaOrbit/p3300!!
* put the two cab files on your device and run them.
* get activesync connection
* run dos window
* soft reset after 100% to get activesync connection.
- only when the rom update utility window opened on pc..
* uspl cmon rom update utility.
***ONLY after doing uspl is it safe to flash a rom.
* if you have an SD card in the device, take it out..
when you have done uspl on your device startup you will see..
SPL: 1.11.cmon
* its done.
USPL 1.11.CMON
http://forum.xda-developers.com/attachment.php?attachmentid=41246&d=1181558635
message me if you get stuck..
Having problems with this.
For 2 days I try all the files and ways to set 1.11.cmon on my P3300 and always stuck at one place no matter what versions of the program I get.
IPL 3.07.0001
SPL 1.11.0000
GSM 02.98.90
OS 3.13.0.0
are the red numbers I see when I restart it.
The problems are that when connect phone and see connected on ActiveSync I start start_uspl program. After 100% connection with Active Sync dissapears and I see black screen on my PPC, then I run ROMUpdateUtility and It says some error that there is no phone connected.
If I start ROMUpdateUtility before start_uspl I go in to boot loader mode ( the 3 colors screen ) and then again that there is no phone connected.
I have done this 15 times or more with different versions of the program and it stucks on the same places ALL the time no matter what version I use.
My artemis had 1.11.cmon before, but I installed the LAST Artemis P3300 ROM from the WIKI. That removed the 1.11.cmon from the phone. After that I have Installed Vanilla 2.0 WWE version on the phone and started the process to set 1.11.cmon on the phone. No success. After some 6.5.5 ROM from the forum, then process to set 1.11.cmon and again nothing...
Please HELP!
i am also having the exact same problem with this , have tried everything to get this to work.
iant2008 mate I did solve the problem
All works as the brains here say. My problem was that I am using Windows 7 at home and Windows Vista at other place I did try to fix this problem. However with Windows XP this whole operation works properly as the people here say. Big thanks to them and I hope you success in this operation too
raving_nanza said:
DONT try to install any rom untill you flash ''uspl cmon''!
you might brick the O2xdaOrbit/p3300!!
* put the two cab files on your device and run them.
- Cert_SPCS
- EnableRapi
* get activesync connection
* run dos window
* soft reset after 100% to get activesync connection.
- only when the rom update utility window opened on pc..
* uspl cmon rom update utility.
***ONLY after doing uspl is it safe to flash a rom.
* if you have an SD card in the device, take it out..
when you have done uspl on your device startup you will see..
SPL: 1.11.cmon
* its done.
USPL 1.11.CMON
http://forum.xda-developers.com/attachment.php?attachmentid=41246&d=1181558635
message me if you get stuck..
Click to expand...
Click to collapse
* soft reset after 100% when the rom update utility window opened on pc..
''to get activesync connection''
it should work dude
Dear Friends,
After USPL the screen of Artemis becomes white and running RUU ends up with error 266. And even after a soft reset running RUU ends until 3% after that comes error 270.
Any solution will be highly appreciated.
Thanks and regards,
Sameeha
...
sameeha said:
Dear Friends,
After USPL the screen of Artemis becomes white and running RUU ends up with error 266. And even after a soft reset running RUU ends until 3% after that comes error 270.
Any solution will be highly appreciated.
Thanks and regards,
Sameeha
Click to expand...
Click to collapse
put the 2cabs on your device and run them..
rapi & cert
run_startuspl - on pc
when this is 100% - soft reset device
-now continue to do rom update utility (uspl ruu)
this should work..?
Hi, raving-nanza,
Thank you very much for your advise. I did that too but nothing happened, error 270 again. errrr? very irritating dude? Any other solution?
Cheers,
Sameeha
...
sameeha said:
Hi, raving-nanza,
Thank you very much for your advise. I did that too but nothing happened, error 270 again. errrr? very irritating dude? Any other solution?
Cheers,
Sameeha
Click to expand...
Click to collapse
i have to admit, i had same trouble to do uspl1.11cmon but eventually it worked.. frustrating.. i know.. but keep trying.. if i was you i would flash back to the official rom.. which should get rid of 1.11.0000 and set back to original spl..
i put rapi and cert on my device, ran them, connected to pc, ran ''run_startuspl'' that made penguin on screen on device.. went to 100% then white screen.. Ruu automaticly opened on pc but i didnt continue with Ruu.. i soft reset device, got activesync connection again and then i continued with the open Ruu..
(Ruu - rom update utility)
Thanks RN, you know, I was trying all this time and my Artemis frozen now (freezes on startup screen IPL 1.25.0001 / SPL 1.27.0000 / GSM 02.69.90 / OS 3.4.0.0. and dopod logo) not moving further. Whats going on? Can you help me?!
Cheers,
Sameeha
...
add me to messenger..
will be much easier than posting
i'm an idiot.....
see this thread
http://forum.xda-developers.com/showthread.php?t=578406
if you run a 3.13 rom; get the 3.13 cmon
if you run a 3.15 rom; get a 3.15.com.
pof's original (kickass great work!!) didn't work with my 3.13 (original htc rom); i ended up with 1.11.000spl. i then ran the 3.13 uspl (see thread); now i am on cmon version
Hi All,
I need your help in urgent!!!
My ELF GSM infor:
- DeviceID: ELF011000
- CID : DOPOD701
My ELF worked fine before I tried to upgrade its IPL from 1.11.0002 to 2.26.0002, then this problem occur. Because a WM 6.1 ROM requires to have IPL 2.27.0002 and SPL 2.28.0000 so I kept continue upgrade the IPL/SPL to 2.27.0002 and 2.28.0000.
I tried to flash my ELF, from bootloader mode, with these ROMs:
- RUU_Elf_DOPOD_chs_1.11.706.1B, this ROM I got from a China forum, it is my device original ROM
- RUU_Elf_DOPODASIA_WWE_1.11.707.1B_4.1.13.42_02.93.90_Ship.exe
- RUU_Elf_DOPODASIA_WWE_1.17.707.2B_4.1.13.46_02.97.90_BLUE_Ship.exe
- RUU_Elf_HTC_Asia_HK_WWE_1.15.721.3B_4.1.13.46_02.97.90_BLUE_Ship.exe
- ESSential_4_5
- Onyx_jr_4_4_2_Light
They are all 100% successfull but the IPL/SPL unchanged (2.27.0002 and 2.28.0000) and the device still loop at smart mobility, can not jump into OS.
I did try to use unbricker ROM and goldcard (with original ROM or unbricker ROM inside) but the ELF still stuck at smart mobility...
Please give me your advices, what should I do (except buying a new phone)?
Thanks for your time!
Flash your Official ROM
rockerboom said:
Hi All,
I need your help in urgent!!!
My ELF GSM infor:
- DeviceID: ELF011000
- CID : DOPOD701
My ELF worked fine before I tried to upgrade its IPL from 1.11.0002 to 2.26.0002, then this problem occur. Because a WM 6.1 ROM requires to have IPL 2.27.0002 and SPL 2.28.0000 so I kept continue upgrade the IPL/SPL to 2.27.0002 and 2.28.0000.
I tried to flash my ELF, from bootloader mode, with these ROMs:
- RUU_Elf_DOPOD_chs_1.11.706.1B, this ROM I got from a China forum, it is my device original ROM
- RUU_Elf_DOPODASIA_WWE_1.11.707.1B_4.1.13.42_02.93.90_Ship.exe
- RUU_Elf_DOPODASIA_WWE_1.17.707.2B_4.1.13.46_02.97.90_BLUE_Ship.exe
- RUU_Elf_HTC_Asia_HK_WWE_1.15.721.3B_4.1.13.46_02.97.90_BLUE_Ship.exe
- ESSential_4_5
- Onyx_jr_4_4_2_Light
They are all 100% successfull but the IPL/SPL unchanged (2.27.0002 and 2.28.0000) and the device still loop at smart mobility, can not jump into OS.
I did try to use unbricker ROM and goldcard (with original ROM or unbricker ROM inside) but the ELF still stuck at smart mobility...
Please give me your advices, what should I do (except buying a new phone)?
Thanks for your time!
Click to expand...
Click to collapse
First try to flash your official ROM and then try to flash ipl/spl again follow step by step. After that try to flash customize ROM again. Hope you will success.
Dear ELF341,
Thanks for your advice!
When I flash the original ROM, 100% successful, then my ELF loop at the China Mobile screen then reset... I don't have the IPL1.11.0002 and SPL 1.11.0000, the lowest I have is IPL1.17.0002 and SPL1.17.0000. I tried to flash back the 1.17 version, after 100% successful, enter bootloader, the IPL 2.27.0002 and SPL 2.28.0000 still remain!?
Please tell me how to do!
Thanks for your time!
rockerboom said:
Dear ELF341,
Thanks for your advice!
When I flash the original ROM, 100% successful, then my ELF loop at the China Mobile screen then reset... I don't have the IPL1.11.0002 and SPL 1.11.0000, the lowest I have is IPL1.17.0002 and SPL1.17.0000. I tried to flash back the 1.17 version, after 100% successful, enter bootloader, the IPL 2.27.0002 and SPL 2.28.0000 still remain!?
Please tell me how to do!
Thanks for your time!
Click to expand...
Click to collapse
After flash back to official ROM , enter bootloader and check ipl/spl first.
Normally, if you flash ipl/spl (not hard spl) when you flash back to the official ROM the ipl/spl will back to original. S/R - wait for boot to WM if OK then do H/R again. And flash ipl/spl again - enter bootloader and check ipl/spl again (changed or not) if OK after that I recommended you flash Onyx ROM. I used it for long time and no trouble.
Hope, it's can help you.
Dear ELF341,
Thanks for your reply!
After 100% successful loading the original ROM, my ELF restart and loop at the China Mobile screen... When I enter bootloader, the IPL/SPL still remain as IPL 2.27.0002 SPL 2.28.0000
I understand that when we flash the original ROM, the IPL/SPL will roll back to its original version, but mine is so strange?! Does this mean that:
- My ELF's flash ROM is fail or locked at the region for IPL/SPL so that whatever ROM I flash (these ROM contain ILP,SPL,OS,radio..) the IPL/SPL unchaged?
- The original ROM is actually not match to my ELF?? But I already flashed the other ship WWE ROM and also the unbricker ROM, they all loop at smart mobility...
Please help me!
rockerboom said:
Dear ELF341,
Thanks for your reply!
After 100% successful loading the original ROM, my ELF restart and loop at the China Mobile screen... When I enter bootloader, the IPL/SPL still remain as IPL 2.27.0002 SPL 2.28.0000
I understand that when we flash the original ROM, the IPL/SPL will roll back to its original version, but mine is so strange?! Does this mean that:
- My ELF's flash ROM is fail or locked at the region for IPL/SPL so that whatever ROM I flash (these ROM contain ILP,SPL,OS,radio..) the IPL/SPL unchaged?
- The original ROM is actually not match to my ELF?? But I already flashed the other ship WWE ROM and also the unbricker ROM, they all loop at smart mobility...
Please help me!
Click to expand...
Click to collapse
How you flashed ROM ? By RUU (PC) or used microSD card. I recommened you to use RUU (PC) follow step by step. Sometime when I used microSD card to flashed ROM , it's successful but cannot boot, after that I flashed Official ROM by RUU and unlocked the phone again it's back to normal. And your official ROM, you must check with your operator or distributor because in different zone it's use diferent ROM.
Dear ELF341,
I only can flash via PC RUU, I don't succeed in SD card way:
- When I copy the *.nbh file into SD card, then enter bootloader, I just can see the checking SD card content string displayed very fast, then the tri color screen.
- When I create a goldcard and copy *nbh file into it, enter bootloader, the brick ask for 'upgrading SD image', I press power button for it to start download but it hang at 'downloading from SD' with a blank download status bar.
Actually I bought this ELF from a man on my local site, so I don't know where is the distributor...I used the mtty and usb monitor to check for my device infor, then search internet for my original ROM, I only can find in a China forum that match my deviceID/CID....
For my case, I really don't know why I can not change its IPL/SPL version? Please help me!!!
Thanks for your time!
well u hav to rename the nbh file to ELF0IMG for SD card flashing to work.
hello people,
i have a problem with my htc touc hd, i had install de spl unlocker with a energy rom but now is my mobile crasht. when I boot I get a few seconders image and then falls off again. I've tried to come in that color screen, which I managed only one I want to install another rom or hspl he remains at 0% hang. maybe someone knows something I can do? I like to hear it
thanks in advance
mark teeuwen said:
hello people,
i have a problem with my htc touc hd, i had install de spl unlocker with a energy rom but now is my mobile crasht. when I boot I get a few seconders image and then falls off again. I've tried to come in that color screen, which I managed only one I want to install another rom or hspl he remains at 0% hang. maybe someone knows something I can do? I like to hear it
thanks in advance
Click to expand...
Click to collapse
Ok, run me through exactly what you did. You installed an SPL unlocker? Which one and how? Did you install this and then flash NRG rom?
Put your device into bootloader (tri-colour screen) and tell me your current SPL?
I need more info to help ya
I have a uspl unlocker installed instead of a hspl unlocker, and then I put out a Engergy ROM, I have a few days worked alone when he fell off. now he does nothing more he goes on and Mentens again and when I put him in that color screen hspl then I try to put on them or any other rom but then he gets stuck at 0%! and if I would just boot splash screen you get started with mobility and then he falls off: S I've put out this uspl: http://forum.xda-developers.com/showthread.php?t=505377
mark teeuwen said:
I have a uspl unlocker installed instead of a hspl unlocker, and then I put out a Engergy ROM, I have a few days worked alone when he fell off. now he does nothing more he goes on and Mentens again and when I put him in that color screen hspl then I try to put on them or any other rom but then he gets stuck at 0%! and if I would just boot splash screen you get started with mobility and then he falls off: S I've put out this uspl: http://forum.xda-developers.com/showthread.php?t=505377
Click to expand...
Click to collapse
Ok, well the Dummies Guide thread you linked to is the correct guide to use
You say you have USPL installed. This needs to be re-installed before every flash to a rom as its not permanent. You SPL should state SPL 1.54.000 before you use USPL
HSPL is permanent so once you put it on you do not need to re-use it again before each flash
You use either USPL or HSPL......not both together. If you have SPL 1.54.000 you choose which to use
You then said you tried to put HSPL on or another rom. Don't forget if you didn't get HSPL on you could try USPL again before trying to flash a rom.
Alternatively try the trouble shooting section and use SSPL to put HSPL on device
Hope this helps
Rick