Hi,
Recently was dropped.
(1) Headphone socket is broken. Where to get it?
(2) Whenever try to use camera device reboots stating buffer device etc.
Please advise.
Appreciate assistance.
Regards
Zaksupra
Double post.
Closed
Related
hi,
this is my first thread here, sorry for my bad english - but i'll try my best.
i want to connect my xda2 with the 22 pin-connector for mp3 in my car.
in your conectors-page is a note:
Audio needs to be capacitively coupled in, any DC bias seems to inhibit audio
i want to ask, what c is needed here? (how many farrad, what kind of C)?
please can you give me some tipps?
is there anyone who has built such a connection? is this a good way to connect the xda2 through the car-radio, or is it better to connect via audio-jack?
my opinion: i found it very uncomfortable to connect first the audio-connector (specially in the dark), and i would be very happy if it works through the 22-pin connector.
please please...gimme a tipp.
or did anyone connect the xda2 and car-stereo without couple-c?
c'mon please, a little answer and i'll be happy.
anyone must have finished a 22pol-connector by himself, or am i wrong?
ty
frustrated...(bad first experience)...
you may be asking too much of a technical question for the cuurent people who watch this board.. i get the impression that the xda-developers site started out with a lot of smart people reverse engineering and dismantling the devices, but its now become more of a software tech support site than a hardcore HTC guru site..
Hi there sorry to hear you have had a bad experience.
as stated xda-dev no longer is as good as it used to be.
i had a quick look at the diagram and from what i can see you should not need capacitors at all.
from what i can see if you connect up pins 3 and 4 to the necessary inputs on your stereo the sound is fine.
a problem i can see however is that to get output on these pins you need to attach pin 19 to ground with a 10k resistor...but this will also redirect the microphone so you wont be able to use it as a phone whilst you have it plugged in unless you also build in a microphone (mind you this should be pretty easy if you wish to do it).
hope that helps
Tim
Hello all,
My Qtek 2020 (Himalaya PH10B) fell on the floor with the headphones on, and the mini-jack for connector for the headphones broke inside it.
I successfully opened it, and I was able to see the damages. I can see only 6 pins that connected the mini-jack plug to the main board, and it seems that there could be a seventh that got broken...
Would anyone of you know of a closeup picture of this headset plug/connector ? Do you know if it is possible to find a new one ? If not, mine looks reparable still, but I would feel reassured if I knew the exact connection here
Thank you in advance for your help.
Cheers
Thomas
http://forum.xda-developers.com/showthread.php?t=225372&highlight=connector
Thank you for your answer Rudegar,
I re-soldered the connector, and I realized that a pin was indeed missing. I actually found it freely moving inside the PDA, but I could not solder it back to the connector. The results ? Well, it still does not work, unfortunately... With the headset on, it is mainly okay (there is still a little contact problem) but *withou* the headset, it still has no sound...
So :
1) Can I find this connector somewhere ?
2) Is there a way to tell the PDA not to check for the headset, and use the main speaker all the time ?
3) Would it change anything if I bought a blutooth headset ?
Thank you in advance !
Cheers
Thomas
1.) i doubt it would be a cheap option if htc had a special connector made just for their phones so i'd asume they use some sort of std component
and maybe there even is a partNr og serial on the connector
which could be used to find a replacement in R&S catalog
http://www.rs-components.com/index.html
2.) no pretty sure the switch between headset and internal speaker is don in hardware and software cant control it
3.) no with bluetooth headset you just dont use the audio connector which mean it would be empty and you'd have no sound on the pda
but it would prob solve poor contact issue of your current headset
Thank you Rudegar !
I am going to re-open it and check if I can find any serial # on the component. It looks like it is my best option. Obviously, if I find something, I will post it on that forum, so that other people can know...
Thanks again !
Cheers
Thomas
Hi all,
I need the frequency response specifications(Magnitude Vs frequency) of the microphone and speaker used in the HTC dopod phone?
I opened the device and found the chip name details as
MIC: S799 369
SPEAKER: SBD 201538P CC03 643
I could not find who the manufacturer of htese chips?
Please help me,
Thanks
Ravikiran N
Hi,
Dopod 900.
Recently was dropped.
(1) Head socket broken. Where to get it?
(2) Whenever trying to use camera, device reboots stating buffer etc...
Please advise.
Appreciate assistance.
Regards
Zaksupra
Welcome to forums
For number 2 perhaps doing a hard reset could help
Also try to remove some apps, if its too heavy loaded of apps will not work well
Read the Wiki
Good luck,
Hi this is my first post here after it being recommended from another forum
I’ve recently purchased a android unit for a 2012 Range Rover evoque and the USB port is not working. It’s the only one and there is power, it’s able to charge devices but I cannot use a memory stick or my CarPlay adapter
I’ve attached some photos of the system information from factory settings and a photo of usb device test
If anybody has any ideas on how I can fix this is would be hugely appreciated!
If you need anymore information about the unit just ask
Anybody have any ideas at all?
wizzi08 said:
Anybody have any ideas at all?
Click to expand...
Click to collapse
Seems to be a hardware issue. You should get in contact with the seller to get this fixed.
I’ve tried contacting the seller and unfortunately they are not interested/don’t want to help
Then open a dispute and send the unit back.
rigattoni said:
Then open a dispute and send the unit back.
Click to expand...
Click to collapse
The last option is to connect a small USB hub but I would be sending it back because who knows down the track what other issues may arise.
I put a small hub in the middle of my center console so that all the USB's can be inserted at anytime.
Sending it back/disputes/refunds etc are not a option. I’m stuck with the unit and I’d really like to find a way to fix it
wizzi08 said:
Sending it back/disputes/refunds etc are not a option. I’m stuck with the unit and I’d really like to find a way to fix it
Click to expand...
Click to collapse
So how to find a way to fix it if the data connection is broken in a forum?
This is no software issue. It´s a real hardware issue.
Sending this crap back is the only option, if you don´t want pay for a repair at a local specialist.
@sandpita
Sorry, but a USB hub does not make any sense if the USB does not work at all, just spending 5V, but no data. Didn´t you read his posting good enough?
I know from past experience with Linux/android boxes/libreelec/coreelec that 9 times out of ten a USB port that has 5v but no data is normally a software, firmware or kernel issue. I was told this and another forum would be the best place to get advice for these types of devices. Of course if sending it back was a option I wouldn’t even be here
rigattoni said:
So how to find a way to fix it if the data connection is broken in a forum?
This is no software issue. It´s a real hardware issue.
Sending this crap back is the only option, if you don´t want pay for a repair at a local specialist.
@sandpita
Sorry, but a USB hub does not make any sense if the USB does not work at all, just spending 5V, but no data. Didn´t you read his posting good enough?
Click to expand...
Click to collapse
My apologies, I didn't read it correctly and relax it was a simple error on my side.
Hey , i think i have a very similar version of this unit .
Mine is a new version for a 2012 RRS
I also had this issue ! , i resolved it by looking at the cable that goes into rear of the unit and one of the pins came unclipped. it happened after removing it so many times. Pushing it in fixed the issue.
Also, If this dont fix it. Enable developer mode . Looks for USB settings in there, theres an option in there that can change it from USB charging mode to data
Issues so far with mine
OEM interface didnt work - Update from seller
Overheating - Update from seller
Mic not working - Added a USB microphone
GPS signal weak - New GPS antenna
I am onto the last problem which is stopping me putting it in the car.
When ever i use Bluetooth Phone, I get a relay clicking sound from inside the unit . I then cant hear anything from the person on the other side. When i end the call it then clicks again and the stereo starts playing.
I also get the same clicking sound from Google Voice
Could you show me a pic of your phone app on your unit ? also.. Do you get what i mentioned above ?
Hi thanks for the reply ! I have very similar issues to yours!
- original car menus show a black screen with the digital version of the physical buttons it replaced Down the sides
-Reverse camera is also a black screen
-Usb not working as mentioned- I’ll try your cable fix though I’ve already enabled developer settings
-I haven’t had any overheating issues but I haven’t been on any journeys longer than a hour or so yet
Microphone is working ok and the Bluetooth audio and phone all work ok
I will add some photos tomorrow when I’m back with the car
My seller is useless and won’t help at all they simply ignore me, what update did they send you? My vehicle is a 2012 evoque dynamic lux