Hello,
this is what the problem is, the power button doesnt bring it back to life. i do a soft reset, it says press zero to clear, i do that it doesnt work. then i do a hard re-set and it shows 'serial', i plug in the usb and it changes to USB (think that's what is called the boot loader'.
now i ran teh exec official firmware, it managed to update it onces but after that i did a soft reset and it didnt come to life. i repeated that process again but this time the firmware didnt even manage to communicate with the device as it said unknown usb device. and then i got an error 101, connection error
any ideas whati can do to make sure it gets restored, i am really going nuts now!!
Same Problem
I am having the same problem with my 02 exec. My phone keeps on being in bootloader, I have tried mtty and I don't have usb connection. Hmm I have tried uni_exitbootloader ,but it tells me that it can not open my usb port. Which sucks. Truely and I am stuck. I am running vista. So I am stumped because I don't know what else to do.
Me too
I am stuck on bootloader page the one that says USB at the top and V1.00 at the bottom. I have Vista so can not use mtty or the other one. I have turned off the USB on Windows Mobile thingy from Vista like activesync. I can get the white screen to show O and X for either factory reset or exit. And I have tried the bootloader screen as noted above. So can anyone help?
i got it working for 2days and then when i was on wifi, it crashed again and wont start again, i get to serial/usb mode of bootloader and also to hard reset when i press 0 to clear everything. but then it doesnt start again.
i thought it was something to do with the battery so i put in a new battery but that still doesnt help.
can someone send me a link to mtty and what to use it. i shall give that a try again.
thanks
mines just still stuck
same im still stuck in boot loader wont budge from he bootloader screen with serial v1.00 on cannot connect via usb as the connection broken i use a extrunal battery charger and got serveral batterys any help yet?
so I installed the nandroid rom and my calls where getting messed up. I cant do a hard reset. It will say its done in a second and dose nothing. tried a hard reset in the sd/phone settings and just rebots the phone. So I cleared all the data I could. My calls work now but my vpn password has been ereased and i dont know it. I do have the phone synced up to the pc, disk drives where installed. Now i tried to reinstall the rom and it says usb fail. Tried to use custom RUU and that says usb failed. I tried every thing I could think of and nothing will go through. Please help I have no idea what to do.
How are you exactly trying to reinstall it?
I tend to do all my flashing via bootloader (holding volume down upon start/restart) and have never had an issue.
Give us a step by step guide as to:
A. What are you trying to flash
B. How are you trying to flash it
well im trying to install any rom right now. I have the MDJ_FroYo_Revolution rom right now. I did the MAGLDR and tried it again and dose it in 1 second. In the MDJ file it has DFT android install and that says it cant find the usb, even on the boatloader screen. the boatloader screen dose see the usb. I tried the custom RUU (PDA Phone ROM Update Utility 3.27.4.3) that cant find the usb. Tried this in boatloader to.
Now I do have the phone synced with HTC sync. Windows mobile will not read the phone. But the computer dose find the phone and has it with its drivers. So what do you think i should do.
If you're trying to flash again using a NAND android build you need to hold the power button when turning on to enter the MAGLDR menu, then select usb flash. Connect your usb then run the daf.exe, that will reinstall for you if I understand this is what you're trying to achieve.
Yes that is what im trying to do. The android flasher mode reads the usb but the DFT dose not. It gives me,
Error USB init failed
INFO: \RSPL\RSPL.cpp (723)
Thats what it gives me in any mode I put the Phone in.
fastenhard said:
Yes that is what im trying to do. The android flasher mode reads the usb but the DFT dose not. It gives me,
Error USB init failed
INFO: \RSPL\RSPL.cpp (723)
Thats what it gives me in any mode I put the Phone in.
Click to expand...
Click to collapse
Check the following thread, should solve your problem and have you back on your way to more happy flashing.
http://forum.xda-developers.com/showthread.php?t=895655
I have HTC HD2,I was trying to upgrade to Android, I think I made a mistake I installed “MAGLDR113” before upgrading my Radio to version 2.15.50.14. After I installed MAGLDR113 I connected my phone to my computer and the telephone was stuck in boot mode and was never able to see USB connection. Now my computer does not recognize my phone anymore and I can’t flash a new Radio version since I have no connectivity to my computer. I tried several things but all was useless. Can anyone help me telling me how I can have a USB connection to my computer??
Thank you.
do you have tried to start and hold volume button... than connect to usb and simply install a stock rom (for example from your provider) - this must work... if not - you have bigger problem.
muhanad said:
I have HTC HD2,I was trying to upgrade to Android, I think I made a mistake I installed “MAGLDR113” before upgrading my Radio to version 2.15.50.14. After I installed MAGLDR113 I connected my phone to my computer and the telephone was stuck in boot mode and was never able to see USB connection. Now my computer does not recognize my phone anymore and I can’t flash a new Radio version since I have no connectivity to my computer. I tried several things but all was useless. Can anyone help me telling me how I can have a USB connection to my computer??
Thank you.
Click to expand...
Click to collapse
Answered so many times. turn your phone off then turn it on "while holding volume down.It will then take to bootloader(rainbow screen).It suppose to have a cotulla written above the rainbow screen.Now flash it with a stock rom came from HTC site..No need to sync your phone to your PC..Just flash it..Start all over again..Now you can search before doing somehing with your phone.If that didn't help you. You have a bigger problem..
Yes I tried this also but it doesn't work.
What didn't work? Can you boot into bootloader - ie switch off, press and hold vol down button and switch phone on.
You should then boot into a multi-coloured screen and should see "serial" at the bottom of the screen.Then connect device to usb port (preferably one at back of your pc and a different one that you haven't used before if possible) - let the drivers install if applicable - does "serial" change to "usb"?
Do wat d above posters have suggested then try different usb ports or even a different windows pc...For all we know, your usb cable might be faulty....Also did u perform HARDSPL before anything else?
I've started experiencing this very same thing. HD2 wont regognize usb connection while in bootloader screen. I get the usb connection sound but never says usb at bottom of screen like it used to. I've been trying android builds via sd but wanted to try my first flash but cant even instal MAGLDR cos it just fails at bootloader cos of no connection. Has been driving me wild for 3 days now.
try plugging the phone into a different USB port it should work then...
Tried that all day and it said couldn't install drivers, then just tried the same ports now and its worked. I think it was mobile device center had 2 set-ups for my phone, i deleted the older one and all seems fine now.
This is crazy, now i'm stuck on magldr and won't find usb.
I'm leaving nand now cos i'm close to smashing my phone to pieces, magldr usb flasher will not find the connection no matter what i try, so i'm staying with ****ty windows mobile. Not happy but i've been trying for days now.
Smoke74 said:
I've started experiencing this very same thing. HD2 wont regognize usb connection while in bootloader screen. I get the usb connection sound but never says usb at bottom of screen like it used to. I've been trying android builds via sd but wanted to try my first flash but cant even instal MAGLDR cos it just fails at bootloader cos of no connection. Has been driving me wild for 3 days now.
Click to expand...
Click to collapse
I am experiencing this exact same problem. Bootloader wont recognize the USB stays in SERIAL. Tried different ports, cord is fine. What is the problem.
Before this, my HTC HD2 would just hard reset on its own ONCE A DAY! Why was it doing this?
Now it gets stuck on the white HTC loading screen. Wont get passed it. I used to be able to hard reset by doing the volume keys down and reset but NOPE... still wont load past that white screen.
HELP!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Have you guys tried deleting the drivers using a utility like USBDeview? Try deleting anything that relates to HTC OR HD2, replug the phone in, re-install the drivers.
h.nocturna said:
Have you guys tried deleting the drivers using a utility like USBDeview? Try deleting anything that relates to HTC OR HD2, replug the phone in, re-install the drivers.
Click to expand...
Click to collapse
IDK what USBDeview is.
Im in Safemode so no drivers load up... because it didnt work in Normal mode. Still nothing
taha23 said:
IDK what USBDeview is.
Im in Safemode so no drivers load up... because it didnt work in Normal mode. Still nothing
Click to expand...
Click to collapse
Of course it won't work without drivers. The computer needs drivers to communicate with the phone. In normal mode, unplug the phone, Google the application, download it, open it, click everything that has HTC or HD2 in it and click uninstall. Plug the phone in, let the drivers install themselves again. Try again.
h.nocturna said:
Of course it won't work without drivers. The computer needs drivers to communicate with the phone. In normal mode, unplug the phone, Google the application, download it, open it, click everything that has HTC or HD2 in it and click uninstall. Plug the phone in, let the drivers install themselves again. Try again.
Click to expand...
Click to collapse
Ok... i rebooted into Normal mode, downloaded the utility, did a search for "HTC" found nothing, did a search for "HD" found nothing. So i am now installing windows mobile center for windows 7 which should have the appropriate drivers.
Install Windows mobile device center 6.1, problem solved.
Sent from my HTC HD2 using XDA Premium App
I'm able to view through USBDeview that my HD2 is connected, however I'm unable to view/open it.. I screwed up by naming the 'temp' folder to 'copy_to_sd_root'..
The instructions confused me. I figured this was the folder that needed to be copied to the sd root... however when i rebooted the phone, I was unable to access it. Any recommendations?
SOLVED
I was overlooking the USB Flash option.
If you are still having problems, let your phone turn on(no multi-color screen), select: USB Flash, click the DAF.exe installation file, follow the prompts.
You're done.
I had this problem and I solved it disabling an option in activesync. I can't remember what was exactly the checkbox, but was in "options" and it said something like "allow usb connections" or something like this.
I just disabled it and rebooted the device holding volume down.
Good luck!
Make Sure Phone is not connected to PC
Goto cotrol panel in windows
Uninstall HTC BMP USB Driver
Uninstall HTC Driver Installer
Uninstall HTC Sync
Unisntall Windows Mobile Device Center
Restart the PC
start the phone holding power and vol dn and now connect the phone to PC. should detect and install the drivers and you should be able to see USB on phone screen.
if this does not work
Delete all the USB root HUB but keep as last option in device manager.
PS: This will cause ALL the USB devices to redetect.
Let me know if this works
Hello,
I recently successfully installed Windows Phone 7 rom onto my HTC HD2. The phone was working fine and would charge the battery when connected to a dedicated charger on the wall plug as well when it was plugged into another computer. I recently attempted to plug the phone into the computer via USB only to find it wouldn't recognize it ,no prompts on the computer or the orange light on the phone. I turned off the phone, removed the battery for several minutes, I started the phone up again and it would boot into Windows Phone 7 normally without any errors but still it would not be recognized by the computer or allow itself to be charged by an external battery power. I had read somewhere that if I where to select Mass Storage option off the bootloader that it would charge the battery and create a partition on the computer. Huzzah! the computer recognized the partition, but the battery still wasn't charging. Going through multiple threads I have read that it might Magldr others say it's the windows phone 7 rom not being fully stable yet and messing with the battery settings, I don't know where to go from here, i'm hoping someone can help. Here are the direct steps that I took since I got the phone:
Phone: HTC HD2 T Mobile
1. Unlock the phone (successfully)
2. installed HSLP3
3. Flashed Radio leo 2.15.50.14
4. Installed/Flashed MAGLDR113
5. Using USB Flasher installed the LEO70_ROM
That's all no settings afterwards were messed with, and Windows phone 7 came up normally and worked perfectly.
Side note: I have tried multiple micro USB cords and different Socket Wall Chargers.
Any assistance is greatly appreciated.
Thanks,
Mr_Pickles
I've yet to find out why it does this, or a step by step guide to fix it, however it is fixable, it will charge battery if you boot to magldr mode, no light will come on but it does charge, mine done this before and came out of it seemingly by its self, or more likely by a combo of things I did, anyhow, charge it up in magldr first, also try using usbdview to list all your USB devices, delete them all, windows can get confused some times
well fancy that, just happened to me again there, ok, so was at work, and my phone wouldnt take a charge via the socket or USB port on a working PC, like i said before it does charge via magldr
anyhow, just got home and plugged it in to my PC that i know it syncs with and all was fine.
So for you i'd definitely suggest deleteing your USB devices to make sure there is no conflicts, charge up your phone via a wall charger in magldr, then get it working with your PC, perhaps then you will get it working,
Thanks, it still isn't charging when it's on MAGLDR, i'm starting to think the battery might be dead. Either way I've ordered an external battery charger and an extra battery, hopefully that solves my issue. Although it still perplexes me why when attempted to connect to a computer it doesn't recognize it.
Unfortunately at this point the battery is completely drain so I can't do anything until the charger and the extra battery comes, but until then i'll keep digging for the answer.
Cheers,
Mr_Pickles
Mr_Pickles said:
Thanks, it still isn't charging when it's on MAGLDR, i'm starting to think the battery might be dead. Either way I've ordered an external battery charger and an extra battery, hopefully that solves my issue. Although it still perplexes me why when attempted to connect to a computer it doesn't recognize it.
Unfortunately at this point the battery is completely drain so I can't do anything until the charger and the extra battery comes, but until then i'll keep digging for the answer.
Cheers,
Mr_Pickles
Click to expand...
Click to collapse
ah yes that is a problem, youve got the charger coming so its a bit late now but that happened to me once, if its just a bit too dead to get you to magldr to charge then i found if you pop it out, wrap it in a cloth and warm it up, do not place it directly on a heat source, by warming it up a bit it helps give it a wee nudge with its chemical reactions inside, potentially enough to get in to magldr.
there is no way of knowing if its charging via magldr other than it not turning off. but with an external on the way you will be fine.
as for it having issues
im guessing its because the battery controller on the HD2 isnt the same as the controller from where the ROM was pulled, meaning whilst its compatible, its not ideal, the not connecting thing could be a symptom of this, im just guessing here but if lets say the battery controler forgets what its doing could that knock out the who USB connection, the USB ports on the computer will have com ports connected whilst the charger will only have the power ports connected, perhaps a combo of all of these things is the reason
but what id do is get it charged first, use the program USBDVIEW (google it) and remove all USB devices associated with a connection to a HUB reboot and connect the HD2 (fully charged) to a different port than usual. it should install drivers and away you go!
Ok! So i got the charger and did all the steps below but still nothing, the computer won't recognize the phone through USB unless I go to Mass Storage option off of MAGLDR. Any thoughts?
The Windows 7 OS runs just fine. It's the connection to the computer/charger through USB that is the problem. Even when loading the boot loader (multi color screen) and then connecting the USB it won't recognize it, the bottom stays on "Serial".
Any help would be much appreciated.
Thank you,
Mr_Pickles
righty, this could be a challenge,
so usb storage mode IS detected when you plug it in with magldr
therefore we can rule out hardware issues
So physically it will connect, that leaves several different possible issues
first things first, you didnt mess about with USB tethering did you? i really hope you didnt and if you did you better start praying your phone is still unlocked and will allow unsigned apps, and that you still have the USB tethering app installed!
next, WP7 software issue, something is buggered stopping it for connecting,
unlikely if you cant connect via the SPL
Desktop Driver issue.
if there is any USB conflict on your PC it can create many problems for you did you try uninstalling all USB devices using USBDVIEW in admin mode, then try plugging it in again?
ok some other questions, does MAGLDR allow you to go to and use USB flasher mode, as if you where updating you WP7 ROM? does your PC connect and install a device driver when you plug it in? (make sure you deleted all USB devices before hand)
lastly, do you have access to another computer that has NOT had this phone plugged in to?, purely to see if it will get detected in SLP mode or ideally in WP7 itsself? this would obviously rule out your whole PC and would help pinpoint the issue!
Hi Dazza,
Here are the answers to your questions:
Q: first things first, you didnt mess about with USB tethering did you? i really hope you didnt and if you did you better start praying your phone is still unlocked and will allow unsigned apps, and that you still have the USB tethering app installed!
A: I did not mess with the USB tethering, my phone is still unlocked.
Q: Desktop Driver issue.
if there is any USB conflict on your PC it can create many problems for you did you try uninstalling all USB devices using USBDVIEW in admin mode, then try plugging it in again?
A: Yes I did, it still did not connect to the device, not allowing to view it as a storage device or charge the phone. The phone also does not recognize that it has been plugged in to the computer.
Q: ok some other questions, does MAGLDR allow you to go to and use USB flasher mode, as if you where updating you WP7 ROM? does your PC connect and install a device driver when you plug it in? (make sure you deleted all USB devices before hand)
A: Yes it does, it installs the drives and the phone shows the connection has been made through USB.
Q: lastly, do you have access to another computer that has NOT had this phone plugged in to?, purely to see if it will get detected in SLP mode or ideally in WP7 itsself? this would obviously rule out your whole PC and would help pinpoint the issue!
A: Yes I have. I tried 3 different computers and none of them recognize the phone.
Side notes:
- I have flashed an Android ROM to see if that would fix the error so I can switch back to WIN 7, but even with the android ROM the computer still does not recognize the phone being plugged in, nor does the phone recognize it has been plugged into the computer.
- When I have gone to the bootloader (multi color screen) in my attempts to bring back the phone to it's orginal state, it still does recognize the phone and won't let me install the base OS and radios for the phone.
I hope this info helps, man i'm really starting to regret getting this phone.
Thanks,
Mr_Pickles
ok, think we need to start again, its sounding all a bit dodgy, MAGLDR is working but the bootloader and WP7 itsself isnt....
you tried reflashing android to no effect
the only common denominator is the SPL/HSPL and the Radio
However because bootloader isnt working in USB mode you cant flash....
SO, next attempt is.....
Format a small SD card, format it as FAT32 or if that fails try FAT16 (512MB card) this is the tricky bit because some cards will not work.
Downloaded the original ROM for your device, usually a .exe file
Open the exe with a zip/rar program,
Extracted RUU_signed.nhb,
Move ruu-signed.nbh to your sd card,
Rename ruu_signed.nbh to leoimg.nbh
Then power phone off,
pop your small SD card with leoimg on in your HD2
Press and hold volume down, tap power but contiue to hold vol down.
The phone should boot into bootloader mode, and it "should" automatically discover there is a leoimg.nbh file on your sd card and ask you to flash.
If it is the wrong image, you should get a failed install message, but if you phone does nothing at all then either the sd card is faulty or the sd card reader is faulty (unlikely if WP7 was using it), or the nbh file is corrupt.
Faulty SD cards could be format issues, ideally you would format the card in the device itsself but you dont have that option unless android will let you do it, which is always an option!
Righty, hopefully that will reset your device SPL radio and all to the original state, if it works and you can get 6.5 working again see how you get it, its a hunch but i reckeon the SPL got buggered up, i cant see any other logical reason for it not to work, think of the SPL as a BIOS on your PC, if you turn USB off in your BIOS you dont have usb working in the OS.
Just to add to the topic here. If you can still transfer data but not charge or receive power via USB does not mean it is not a hardware issue. It just means the pins for data transfer in the USB port are working. A standard USB port has 5 pins in it (this includes micro and mini USB ports) only 2 of the pins are for power transfer the other 3 are for data transfer.
Also if you do not have ActiveSync or WMDC installed on the computer you connect to via USB while in bootloader you will not get the HTC USB sync (USB in white bar of bootloader) connection because these programs have the USB drivers for the HTC USB sync connection, they are not preloaded on the HD2. Therefore the do not auto install when you plug your USB cable in and are in bootloader. I learned this thechard way.
The OP had posted in the HD2 General forum too and I had advised them to try to use a multi meter to test the battery pins while the charger is plugged into the HD2 to comfirm voltage is getting to the battery. I also advised them to try and flash back to a Windows Mobile ROM to see if charging was possible. Both of these things would rule out a hardware issue.
MAGLDR still has this charging bug, it will let you charge while in USB Mass Sty bit it is not charging the battery correctly and this why, quoted straight from the first post inthe MAGLDR thread.
Battery controller inside LEO needs runtime control during charge, it implemented in OS.,
Click to expand...
Click to collapse
The runtime control means that MAGLDR can not control the rate at which the battery is charged which is not good for 2 reasons. One too little (too slow) of a charge rate or too much (too fast) of a charge rate is detramental to your battery life and battery chargeablity. The secound is to much voltage going to the battery can cause the Li-Ion battery in the HD2 to explode. Now reason number 2 is a very unlikely senerio as all common USB type wall chargers only put out 5.0v to 5.1v and that is safe for Li-Ion batteries, but there is still the risk. But as the quote says the "run time control" is implamented by the OS so when you charge with your HD2 booted into the OS it is safe and not harmful to your battery.
I hope the OP gets their charging issue worked out and I hope it is not a hardware issue.
indeed, the power pins as you pointed out could be the issue, im trying not to complicate things at the moment because even if it was, it should still commence coms to the computer, it does connect via magldr so we can assume that firstly the cable is ok on the data lines, secondly the PC is able to detect the device meaning the device itsself is working
We can also assume that if all USB devices have been removed and no ActiveSync or WMDC is installed then Windows would still detect new hardware but will fail to install it, if the drivers were present and it connected we'd have fixed half the problem!
physically it can connect (magldr proven) but something is prohibiting it in bootloader and the OS, the PC isnt detecting it at all. I dont understand why magldr works and bootloader doesnt unless magldr is able to run its own form of bios, i dont know how it works so i couldnt be sure, so im running with a hunch that the HSPL/SPL is buggered as it wont connect to the pc in bootloader.... if we can flash via SD it will help rule that out.
aye the charger thing on magldr is concerning, but it will be ok to give it a short amount of juice to get to windows, overcharging is the issue, could potentially blow up but its unlikely, the plug charger should have a built in IC to knock it down to a trickle charge when it detects its reversing the polarity....should! lol
Thanks everyone, i'm planning on trying this out tonight when I get home and using the SD to bring it back to stock. Hopefully this solves the problem otherwise I'm thinking that T-Macgnolia is correct and one of the Pins in the USB is broken and would need to be fixed.
I really do appreciate all the effort you guys have given in your response.
Mr_Pickles
Mr_Pickles said:
Thanks everyone, i'm planning on trying this out tonight when I get home and using the SD to bring it back to stock. Hopefully this solves the problem otherwise I'm thinking that T-Macgnolia is correct and one of the Pins in the USB is broken and would need to be fixed.
I really do appreciate all the effort you guys have given in your response.
Mr_Pickles
Click to expand...
Click to collapse
its possible that the bootloader or the OS needs the power to be connected in order to function, you did say that you have tried different USB ports and a number of cables, the only other posibility would be that the pin on the phone its self is broken, thats going to be difficult to test.
do the SD thing first, if that doesnt work boot to android, note the battery level, get it to around 50%, then turn off the phone and boot to MAGLDR, you do not need to have it in USB storage mode or anyother mode, just leave it plugged in at the MAGLDR menu.
now the USB port on a PC will provide no more than 500mAh, so if you had 50% charge that would be about 600mAh in the battery, leave the phone plugged in to your PC in MAGLDR menu for an hour, that should give it no more than 1100mAh of juice, (it will actually be less than that as your screen will still be sucking juice)
if you use the 1A wall charger then only charge it for 30min, just to be on the safe side. (if you can i would recomend this one as it rules out any issues with data pins) and if its not working it wont completely drain your battery sitting there with the screen on
anyhow, boot back in to android and see what the battery level is indicating, if its gone up you know its charging, if its gone down you know it isnt, which may indicate a broken phone.
Good luck and keep us posted!
Success! Loading the stock ROM through the SD and finally my computer recognizes the phone! Thank you so much everyone for your help, I can't tell you how much I appreciate it.
Mr_Pickles said:
Success! Loading the stock ROM through the SD and finally my computer recognizes the phone! Thank you so much everyone for your help, I can't tell you how much I appreciate it.
Click to expand...
Click to collapse
no probs mate, thats why XDA dev is here!
i think its almost certain its a SPL issue, possibly got corrupted somehow, least you know its not hardware, i know this sounds a bit much after all you just went through but dont give up on WP7
Hi Guys,
I had exactly the same problem as Mr_Pickles.
I had tried reflashing the stock rom using the SD card method.
Everything installed normally, but after the flashing the HTC logo appears followed by the Radio version and other info shown in the bottom of the screen in red text.
Then the mobile reboots and keeps doing the same thing again and again.
Could someone help me on this please?
nvenon said:
Hi Guys,
I had exactly the same problem as Mr_Pickles.
I had tried reflashing the stock rom using the SD card method.
Everything installed normally, but after the flashing the HTC logo appears followed by the Radio version and other info shown in the bottom of the screen in red text.
Then the mobile reboots and keeps doing the same thing again and again.
Could someone help me on this please?
Click to expand...
Click to collapse
did you install HSPL? before doing anything or is it doing this restart after you reflashed your Stock ROM via the SD card
nvenon said:
Hi Guys,
I had exactly the same problem as Mr_Pickles.
I had tried reflashing the stock rom using the SD card method.
Everything installed normally, but after the flashing the HTC logo appears followed by the Radio version and other info shown in the bottom of the screen in red text.
Then the mobile reboots and keeps doing the same thing again and again.
Could someone help me on this please?
Click to expand...
Click to collapse
Hey Guys,
I experienced the same problem with the installation of wm6.5 stock rom (with having hspl 2.0 installed) as nvenon and couldn't find a solution.
dazza9075 said:
did you install HSPL? before doing anything or is it doing this restart after you reflashed your Stock ROM via the SD card
Click to expand...
Click to collapse
HSPL 2.0 installed, Stock rom installed via sd card method, still the same problem.
The point is that I read somewhere to just keep on flashing wp7, which works fine until operating XBmod-Yuki Rom Build 7004:
- While the wp7 works fine, the phone can't be recognized by any PC via USB, so i can't update the build via update cab sender
- But: The phone is detectable and chargable in bootloader mode, so now hardware issue?
I would appreciate any help.
Thanks in advance!
Hello,
I have had this problem in the past and it stumped me for a bit of time until I looked very carefully at how I was resetting the device. If you are not careful and with flashing etc you will be ripping the battery out all the time.
Look at the device with the battery out and you will see those 3 little pins. They need to be in a line for the battery to make decent contact with it. Over time if you are constantly taking out your battery it will bend them... you can just use your finger to straighten them.
That should do it. It got to a point I always take out my battery carefully now and make sure these pins are aligned before putting it back in.
okay, this is my time to post here.
using h2owner's wp7.8 rom I got a problems with sudden stop charging till once my battery dead completely.
after that I have (quoting my post from h2o thread):
"
it's not to abuse as we know all the risks we take testing roms, just asking for your advice:
1. I did install your latest rom
2. after some time it stopped charging at all
3. the problem is the phone got unable to charge under sd android as well.
4. at the end of story battery got dead - can't load magldr.
5. managed to direct power on it via red/black cables of usb to +/-
6.but the problem still the same - I can't charge battery via phone
7. and even more - can't enable usb via bootloader (tricolor) - serial only:
- usb flasher works only with wp7 rom install;
- magldr, hspl, task29 flash via usb flasher fails with critical error 0000001;
- naturally, can't flash winmo;
- usb storage works well."
1. nbh of the default os flashed fine
2. pins are aligned
3. issue is still here
please, help if you can
dimdimdim said:
okay, this is my time to post here.
using h2owner's wp7.8 rom I got a problems with sudden stop charging till once my battery dead completely.
after that I have (quoting my post from h2o thread):
"
it's not to abuse as we know all the risks we take testing roms, just asking for your advice:
1. I did install your latest rom
2. after some time it stopped charging at all
3. the problem is the phone got unable to charge under sd android as well.
4. at the end of story battery got dead - can't load magldr.
5. managed to direct power on it via red/black cables of usb to +/-
6.but the problem still the same - I can't charge battery via phone
7. and even more - can't enable usb via bootloader (tricolor) - serial only:
- usb flasher works only with wp7 rom install;
- magldr, hspl, task29 flash via usb flasher fails with critical error 0000001;
- naturally, can't flash winmo;
- usb storage works well."
1. nbh of the default os flashed fine
2. pins are aligned
3. issue is still here
please, help if you can
Click to expand...
Click to collapse
okay, now I got "00028002 not allow" error trying flash stock original rom from sd...
still no sd in bootloader, which changed to 1.42...
completely lost.
Hi guys ,my problem is that when I connect my phone via USB cable at first there is no problem, data transfer , windows mobile device center, everything is OK. But when I want to flash the phone pressing vol-down + switch on/off keys the phone is not connected to the PC. And I can't flash it. Also the phone wouldn't like charge trough the charger ,only with the data cable. Is it possible to have any liaison between the problem with charging with charger and no-connection when try to flash.
Also my phone was to the service for touch-screen change ,is it possible the technician make any mistake ? Cause I think that if he make a mistake with the connector nothing gonna work ,but it works at different situations.
Regards!
check to be sure USB SYNC driver installed correctly and also try a different usb cable.
I'll try but there is no logic ,the cable works when charge the phone, works when is connected to device manager but doesn't works when flashing ?
exactly. the device requires different drivers.
1. there is internet sharing and disk mode (which works with all computers, because those drivers are in the operating system)
2. then there is one driver for syncing
3. and another one for flashing
it is not the same kind of data transfer, which is why you need a different driver. but the thread "[tut] updating htc sync drivers" should cover all your windows vista/7 driver needs and a tutorial on how to install them, which in case of a x64 system can be fairly complicated.
if you already have hspl installed (which you can determine by entering bootloader mode and looking whether it says 1.56Olinex), you can also flash using the sd car method. put a rom of your choice on the sd card, name in BLACIMG.nbh and enter bootloader mode, you will be presented with options to flash the rom.
Ok, but in instructions at the thread you give me is written that I have to start making the steps after I see "USB" on the flashing screen. But I don't see it, it's only "Serial". And now what ? I know that if on the screen i written "USB" the phone and the computer are connected and there is no problem to flash ,but now what ?
well, before you start, put your device into bootloader mode. it will show "serial", then connect it to the pc. test your connection using mtty 1.42 (you'll find several download options here in the forum).
the connection settings for mtty are USB 115200-8-1-No-NONE-None
if it works, connect and press enter, the command shell should show USB> then.
if usb is not present in the connection settings, your connection is not established yet. proceed with the tutorial then. during the entire procedure, the device should remain connected to the pc in bootloader mode, so you install the driver for the right device state.
Hello,
I've problem something like this. Few months ago when i was conecting my phone to computer was everything OK, activesync, disk drive, but now nothing, just charging the phone. I've tryed everything in USB to pc zone, but nothing. When i'm going to bootloader it's writen serial. What can be here?
since you already tried all the different connection methods and even bootloader mode does not connect, there are hardly any options left, where the trouble could be:
- the usb port on the blackstone
- the usb port on the pc
- the cable
you can try another port on the pc (or even better, another pc altogether) and/or another cable, like from a digital camera, an external hdd... (many devices have mini usb cables, you should be able to use either one of those)