I cannot connect to my home network today. When going through all the settings, I see that the IEEE 802.1x checkbox is ticked, but greyed out. How can I remove either the network, or remove the IEEE setting ? I don't know how this changed, as it was working yesterday. I have two notebooks connected to the same router without any problems and neither has this check box ticked. so am presuming this is the problem - the problem being that it will not get an IP address. It finds the network but will not connect. I can see an option to edit the network, and remove the settings, but there is no option that I can see to remove the IEEE setting, or delete the network so I can start again, but am not sure this will prevent the IEEE setting from being selected by some other means. Obviously something caused it to select this, but I don't know what. I have removed any programs I have installed over the past day or so in the hope that this might have resolved it.
ieee802.1x == wifi network
http://en.wikipedia.org/wiki/802.1x
Thanks for that. I realise now that when WEP is selected (which my network is) that IEEE is activated by default. This means that I have some other problem accessing the network. It detects the network, says "connecting" then reverts to available. Never had a problem with this before and at a loss to know how to resolve it. Will try to connect to another network that I know works tomorrow.
enseeess said:
Thanks for that. I realise now that when WEP is selected (which my network is) that IEEE is activated by default. This means that I have some other problem accessing the network. It detects the network, says "connecting" then reverts to available. Never had a problem with this before and at a loss to know how to resolve it. Will try to connect to another network that I know works tomorrow.
Click to expand...
Click to collapse
I also tend to experience similar problem,
there are networks I can never connect to even after configuration,
when other work great..
The problem is that it has never been a problem to connect to this, or any other network. The only change I have made to the PC, which connects to the same router as the X1a is that I have set up one of my browsers to access the internet via a proxy, but I don't think that would impact on the inability of the X1a to access it.
Related
Hi,
I've just got a T-Mobile Vario. It connects fine on GPRS and PIE navigates to web pages.
I then try to connect to a free WiFi hotspot (I have no home wifi network to test on).
It *connects* fine. However, when I try to navigate to a web page it hangs on the "Locate" message, then times out.
I have searched the forum and read similar problems but with home networks not public hotspots- for example:
http://forum.xda-developers.com/viewtopic.php?t=46118
I tried the solutions suggested there but with no luck. Has anyone had similar problems?
I *really* need to get WiFi working (by the end of the weekend hopefully) as thats what I got the device for in the first place.
I am a WiFi virgin so any pointers will help.
ipl 1.06
spl 1.06
gsm 1.12.10
os 1.6.2.4
protocol version 4.0.13.23
ExtROM 1.6.2.105
Cingular 8125 WiFi fails
I have the same results. My router assigns my device an IP address with WiFi on, but I get the message "...the connection was lost." whenever I try to surf internet. If anyone understands how to set it up, we'd appreciate instruction that works (I'd like a Cingular user if possible) but I would also like to learn what the settings mean. Anyone have a link to network setup information? I have a WiFi network in my home which works for my wife's laptop and my old PDA. This 8125 is bugging me.
working now...
OK, as soon as I posted and went back to the PDA the WiFi connection now works - gremlins again... I didn't change anything or even soft reset - it just connected. I wonder if it was because the GPRS connection ended... I'll try turning off my automatic e-mail checking and post again. BTW, I am using the suggestion of the first Network being "work - no proxy" and the second being "MediaNet - proxy"
Your problem doesn't seem the same as mine.
I have no home network.
My vario, on a public hotspot, always "connects" but always fails on "locate".
you need to make sure the connection is not using a proxy server.
go into settings
connections
then manage existing connections
untick the checkbox on the proxy settings tab that says this connection uses a proxy (or words to that effect)
now you should be able to connect to the network as long as their is no security in place to stop you.
good luck
R
Hi,
I have no "manage existing connections"
under settings->connections.
I go into connections which gives <tasks> and <Advanced> tabs
Under Advanced> I have <select networks>
This screen "Network Management" has two drop downs
1 states "Programs that automatically connect to the internet should connect using"
"T-Mobile Internet" is selected
If I edit and look at proxy settings it has:
"This network connects to the internet" ticked
the proxy server box is empty
If I edit the modem tab it has Cellular Line (GPRS) selected
Dropdown 2 has
Programs that automatically connect to a private network should connect using:
the dropdown is filled with "My Work Network"
By default the "connects to the internet" box is empty. I have filled this in previously with no luck.
Modem is empty as are all the other entries.
I have swapped the order of the dropdowns, I have made both "My Work network" and both "T-Mobile Internet" with no luck.
I have tried the suggestions on the thread I referenced above - again with no luck.
To repeat I can get the "connection" up. When I select the network it states connection is "good" yet when I try to surf to a page it craps out on the "Locate" message.
Is it failing to find a DNS server on the wifi link?
I'm just guessing as I know v little about WiFi as I have never used it before
TIA for any further contributions
I just wanted to say I have this same problem and have not been able to solve it yet. I can't tell whether to use GPRS while using Internet, or whether I should have the connection set to "Work" or "Internet" or what.
I have tried with 3 unprotected wireless networks already and have gotten the same results with each. I suspect it may be due to DNS. Hopefully it is not the phone itself.
Hi mat,
Well it can't be that you *must* use GPRS whilst surfing - thats what WIFI is for!
I suspect (no real evidence)T-Mobile have somehow crippled the OS to make it difficult to work out how to get free hotspot access working properly. Looking at their site they say CS do not "support" WIFI access problems - how convenient!!!!!
Although I am a WIFI virgin/idiot, I am not a *total* idiot and would have been able to get it working if it was completely straightforward.
To add ammunition to this opinion, I do not have a T-Zone account (I should have but it hasn't been set up correctly). Anyway I tried to connect though a t-zone and it worked straightaway presenting me with the login page. I could also download data - the terms and conditions.
However, obviously I couldn't surf to totally check it out as I couldn't login.
I wish someone would provide a definitive solution as it is really irritating me now!!!!!
Why would it be hanging on "locate"? I imagine it must be because it cannot look up the IP address through the free WIFI link. I made the same suggestion as you did earlier something to do with the DNS setup.
Thats as far as I can get!!!!!
I was finally able to go online using the wifi. Where it asks what the network connects to, I had to change it to 'Work' instead of 'The Internet.' The problem is now I can't connect to any internal ip's such as my router or other networked computers. A bubble pops up over the wifi icon on the taskbar telling me I need to change my connection settings. Any ideas how to fix this?
Hi bendog2784!
The internet profile is used together with vpn connection settings and the work is for direct internet connection. The difference is in encryption but access should be the same so perhaps your problem is because of incorrect ip settings.
I have since got it to work. I think a lot of it had to do with the tmobile proxy. Not entirely sure though.
I have a SPV M3100 (TyTn, I think) but I cant get it to connect using WiFi to my wireless router. I can go into 'Configure Wireless Networks' and tell it to connect to my router, all the settings are correct, but all it does is try to connect and fail, and no error message comes up.
Does anyone know how I could fix this problem?
Thanks,
Sebastian
it might help if you state what rom your are using and what protection the router is using? I know there are many threads discussing this issue with WM6 using WPA. Have you tried connecting with no encryption? If so can you connect.
Sorry, the ROM version is: 1.23.61.4, date: 7/13/06
It is running WM5 PocketPC. Encryption is WEP. No I havent tried no encryption. I will after when I get home.
Sebastian
OK, I've tried without encryption, and I've fiddled about with the settings but it still doesn't work.
Each time I tell it to connect it says 'Connecting' for about a second then says 'Unavailable' for a few seconds, then back to 'Available', untill I next tell it to connect.
Any suggestions?
thanks,
sebastian
if it use mac filtering the mac of the tytn need to be added to the lists of mac's the router wanna talk to
that's not the problem either, sorry
Couple of things (I'm running WM6 on my M3100, so WM5 is a bit of distant memory ) you could look at.....
First, does your router use DHCP to issue IP addresses? if not, you'll need to set the phone with a static IP. To do that, go to Start / Settings / Connections tab / Wi-Fi / Network adapters tab, make sure it says "connect to the internet" then tap the "802.11" network adapter, tap "use specific ip address", fill one in and "ok" your way back out.
Second, in Start / Settings / Connections tab / Wi-Fi / Wireless tab, tap and hold your "unavailable" wireless connection then choose Edit. Make sure the "connects to" box says Internet. Also, if your router doesn't broadcast its' SSID, (on WM6 at least) tick the box that says "this is a hidden network", then go next, next finish (making sure the authentication and encryption types match your router config!!).
Hope this helps,
Mark.
I have now been through every intricate detail within settings, and still to no avail. One (possibly) good thing did come out of it though - an error message.
I got it when going to create a new WiFi connection and clicking on the 802.1x tab, it says:
"Cannot log on to the wireless network. This network requires a personal certificate to positively identify you."
I made sure I inputted the network key correctly and all the encryption settings were right.
Please tell me that helps solve the problem! lol
btw, the router is a D-Link DSL-604+, just incase that helps anybody solve the problem.
sebastian
If you're getting certificate errors, it sounds as though you've ticked the setting in the phone's wireless config that says something like "IEEE 802.1x network access" and selected "smart card or certificate".
Go back in to the wireless config, tap and hold the "unavailable" network, then select Edit. Go through - next, next and the authentication is on the last page IIRC.....just untick the box, tap finish and you should be away!!
Cheers,
Mark.
It WORKS!!
I forgot to untick 'The network key is automatically provided' and tried to connect, and it now works
I'll just kiss goodbye to my battery life now
Thanks for everyone who has helped me.
Sebastian
My ATT Tilt wont connect to my D-Link Wireless N Router.. does the Tilt not work on N routers?
Hi Guys & Gals,
I have a brand new HTC Touch Diamond 2, on O2 network - this is an untouched device, all i have done is booted it up and sync'd it with my PC,
I have tried to connect the device to to wireless networks now with no luck.
1. My home connection - security enabled WPA-PSK password protected, The phone can see the network, i type in my network key - i also checked the password on my router setup. The little spinning circle comes up and try's to connect with no luck. It will then keep trying for as long as the wireless is on
2. Home connection again with no encription - again the same thing
3. Work connection WEP secured, type in the key, same thing again.
Has anyone encountered these sorts of problems before in the past - if so how do i fix it so i can connect wirelessly.
Cheers Guys
JdeRonde
Doubt if this is an issue with the phone more likely to be a setup of the wireless.
What router do you use?
Do you have MAC Filtering enabled?
Do you use your router as a DHCP server?
Are there any error messages displayed on the phone?
When it doesnt connect and you tap the notification area (top bar to the right of START) do you have any messages there?
jderonde said:
Hi Guys & Gals,
I have a brand new HTC Touch Diamond 2, on O2 network - this is an untouched device, all i have done is booted it up and sync'd it with my PC,
I have tried to connect the device to to wireless networks now with no luck.
1. My home connection - security enabled WPA-PSK password protected, The phone can see the network, i type in my network key - i also checked the password on my router setup. The little spinning circle comes up and try's to connect with no luck. It will then keep trying for as long as the wireless is on
2. Home connection again with no encription - again the same thing
3. Work connection WEP secured, type in the key, same thing again.
Has anyone encountered these sorts of problems before in the past - if so how do i fix it so i can connect wirelessly.
Cheers Guys
JdeRonde
Click to expand...
Click to collapse
I too had problems with WIFI. My home work network was visible but it would immediately drop or not be able to connect. A few days later it started working flawlessly and I have no idea what changed.
I am sure you have tried a soft reset but just in case...
Tony
I have a NetGear DG(Some Number) v4 ADSL wireless router, which i have set up and works for all of my other devices (ie. Laptops, PS3). With a simple encription key.
I get no messages etc, all it sais is that its 'not connected' and there are no new notificatons
It then persists in trying to connect again and again, when it cant connect for a while, it then comes up with 'new network connections found' in the notificatins area.
I have switched the power mode to best performance with no luck.
I have tried on 2 different networks now. including with all encription off. WEP and WPA-PSK - This is driving me nutz cuz i love the phone, i just want to use it to browse the web without paying out the nose for it.
DHCP server is dynamic from my ISP.
I have contacted HTC now about the issue, but im going to feel so stupid if it turns out to be somthing simple like a setting on the phone somewhere.
But thanks for the reply
Have you checked you arn't using MAC filtering?
Log-in to your router and check under Wireless settings > Wireless Station Access List.
While you are on your wireless setting page check what Encryption your using for WPA-PSK? TKIP? (The wrong encryption chosen will cause you not to be able to connect)
Ok maybe telling you how to suck eggs but on your phone:
Settings > Communication > Wifi
Select Advanced at the bottom right.
Select Change Network
Click Add new...
Type in the name of your network (The SSID also found under wireless settings, Case sensitive)
Select Connects to: The Internet
Leave the other two boxes unticked.
Click next.
Select the correct Authentication - WPA-PSK is different to WPA2-PSK. You will probably be using WPA-PSK.
Select the correct Encryption (Propably TKIP)
And type in your Network Key
Click Next and Finish.
How does this fair and what are the results of checking info on wireless setting page?
Im at work at the moment trying to connect to the WEP connection,
This connection most deffinatly does not have mac filtering on it, just asked the network tech.
Okies.....
Changed the network key to.... Shared key and it works
so i am guessing that it must be somthing to do with my setup at home..
Cheers guys
Cool.
Just match up the Authentication / Encryption / SSID and Network Key from the router to your phone setup and you should be fine.
HTC TD2 Wifi issues
Hi
There's some discussion around the web about this problem of encrypted wifi connectivity: a few things to note
1] the TD2 is _very_ sensitive to the power settings applied to the wifi chipset.
The default power saving settings are only likely to work if all other on-board devices - bluetooth, HSDPA, GPS [and maybe even the screen] are either off or in low power mode: the general recommendation seems to be that one adjusts the wifi device power to be "best performance" if one wants to guarantee connections.
2] several people have reported that both the wifi device [card] and the settings for the particular wifi lan [SSID] to which you are attempting to connect should both be configured for "Work" rather than "The Internet".
3] these secured/encrypted connection failures are not about the WiFi access point or router: I've personally tested with several different makes and models of Router and Access Point [3com, Cisco, Enterasys, Netgear, DLink, Belkin etc] - both on my own and on client networks where I have complete control of security, and have also methodically tested every single combination of TD2 setting for WEP and all variants of WPA. In each case my TD2 has failed to make a valid encrypted connection.
The same device will happily connect to "open" unencrypted access points and routers.
Other models of HTC device, such as the Tytyn II and Touch Pro work fine on the same access points and routers: so we can be pretty sure that this is specifically a TD2 issue.
Conversations with HTC's European Tech Support on this issue have not been helpful to date, but they HAVE pushed the issue further up the line, so there's a chance that we'll see a resolution.
Robert
Hi,
I have an HTC Elfin that has no problem connecting to a home network with WEP encryption. But at work, I cannot connect to the network with WPA-TKIP encryption. My phone just tries to connect for a few seconds and then the status of the access point goes back to "available". I've verified the network pass phrase, as it does work with my co-worker's netbook. What is the problem here?
BTW, I've been reading up on this problem and somebody mentioned the fix of turning on/off the wifi (turn on wifi, connect, turn off wifi and then on again), but it doesn't work for me:
http://forum.xda-developers.com/showthread.php?t=327928
dtran707 said:
Hi,
I have an HTC Elfin that has no problem connecting to a home network with WEP encryption. But at work, I cannot connect to the network with WPA-TKIP encryption. My phone just tries to connect for a few seconds and then the status of the access point goes back to "available". I've verified the network pass phrase, as it does work with my co-worker's netbook. What is the problem here?
BTW, I've been reading up on this problem and somebody mentioned the fix of turning on/off the wifi (turn on wifi, connect, turn off wifi and then on again), but it doesn't work for me:
http://forum.xda-developers.com/showthread.php?t=327928
Click to expand...
Click to collapse
Try to set wifi to best performance instead of best battery first.
Often the problem is also caused by a combination of the router (brand/type) and a Windows based device/computer.
Some things you can try to get a working connection with WPA-PSK enabled:
1. Modify the registry:
\HKLM\Comm\EAP\Extension\25\ValidateServerCert=dword:00000000
2. Modify the network settings:
Settings > Connections (tab) > Wi-Fi > Network Adapters (Tab)
and select "NE2000 Compatible Ethernet Driver" (maybe you have to config a static ip-address).
Thanks for the suggestions. I did all those, except for the static IP since our network admin doesn't provide one. It still doesn't work. One thing I'd like to understand is that in my case, why does the WPA-PSK connection work for the standard Windows environment (laptop/netbook, desktop) but not Windows Mobile? What could be the difference?
I donĀ“t know what ROM are you using, but if it is some of 23XXX Builds, disconnect first the Bluetooth and then connect the Wireless... Should work now...
My ROM is MK_872_05 WWE, from chota_shivaji. It uses WM6.5 CE OS 5.2.21872. Thanks for your suggestion. I will try it out on Monday when I get back to work.
I disconnected the Bluetooth connection and tried again to the WPA-PSK encrypted access point at work and it still doesn't work. Just yesterday at a relative's place, I was able to connect to his router with WPA security. I think there's something different with the one at work which does not work with Winmo devices.
at work do u just have a password or a user/password? are u using certificates?
At work I have a guest username and password that I can use to log in for the WIFI access point. The password changes every week, but I confirmed that I used the latest one. But I don't think there's a certificate needed since my co-worker is able to use his home netbook to log in without anything else except the same username and password.