Related
8525, sync w/ USB 5% of the time, no changes seem to change anything.
did the notification edit here on xda
uninstalled/reinstalled activesync
upgraded to 4.5
deleted partnership
uninstalled firewall
checkdisk
ran the resync program
installed office, .net 2.0, activesync 4.5 on entirely different computer
[edit: added for clarification]
tried unchecking the advanced connection box in start>settings>connections>usb to pc
[/edit]
when connecting to either computer, i get the "usb device seen" chime, but not the "i can do something with this device" jingle
get the "active sync cannot connect with this device" popup, run the diags and everything is okay. ms site politely informs me that the cause of my problem is that the device cannot connect to the pc.
anything i missed? i gave up on it 6mo ago when i got the phone bc i got bluetooth sync to work but now i want to flash to wm6
Thanks
start>settings>connections>usb to pc.
Untick the box. See if that helps?
Try this procedure step-by-step
1. make sure your phone is not connected to the computer in any way
a. Bluetooth off
b. WIFI off
c. USB cable not connected
2. Run spybot S&D (I always do this when the computer misbehaves - and make no mistake your computer is misbehaving)
3. Terminate all other running programs
4. Hook your phone to the usb cable and the usb cable to the computer. (don't worry if it syncs or not)
5. Open Device Manager and select Network Adapters
6. Uninstall the Windows Mobile Device
7. Disconnect the Phone
8. Open the Control Panel "Add/Remove Programs" and uninstall Active Sync
9. Reboot the computer
10. Connect to the internet and get a fresh copy of Activesync 4.5 and install it.
At this point if you can back up your PIM to the storage card or something it would be great because I suggest you do a hard reset of the phone. go to the settings page and select System. Tap the clear storage icon and follows the instructions to reet the phone.
11. Reset phone as above
12. When phone reboots, connect it to the computer via the usb cable.
Phone should sync from now on.
Good Luck
PS.
MrVanx is right, that could help but it will limit your phones capability. However if my method fails that may be your only option short of reflashing the phone with some other ROM.
I've tried MrVanx' solution also, just forgot it in the original post. It seems to sync more often when the box is ticked anyhow.
I don't have a problem with hard reseting or flashing. I'm going through this hassle for the sole reason of flashing to schaps 4.31
Ill try that when i get home tonight
Say I do a sprite backup before hard resetting the phone. After I do the hard reset, I restore the sprite backup. Will my lack of syncing problem come back? I assume it will.
After the hard reset and the initial sync on the "fresh WM5 install," I should proceed from there with the WM6 install, correct?
I have a TyTn II and experiencing a similar problem as sook..
I did all the steps except for these:
5. Open Device Manager and select Network Adapters
6. Uninstall the Windows Mobile Device
The thing is i cant find my mobile device anywhere in the device manager or in the network adapters subcategory. Any ideas?
mrvanx said:
start>settings>connections>usb to pc.
Untick the box. See if that helps?
Click to expand...
Click to collapse
+++ worked for me
sook said:
Say I do a sprite backup before hard resetting the phone. After I do the hard reset, I restore the sprite backup. Will my lack of syncing problem come back? I assume it will.
After the hard reset and the initial sync on the "fresh WM5 install," I should proceed from there with the WM6 install, correct?
Click to expand...
Click to collapse
Yes proceed. And no I don't think the failure to sync problem is related to the backups so that should be safe
SeqHTCTyTnII said:
I have a TyTn II and experiencing a similar problem as sook..
I did all the steps except for these:
5. Open Device Manager and select Network Adapters
6. Uninstall the Windows Mobile Device
The thing is i cant find my mobile device anywhere in the device manager or in the network adapters subcategory. Any ideas?
Click to expand...
Click to collapse
Not sure how a TyTN II looks to the device manager. try this instead:
open the device manager and click on the USB devices subcat.
Then connect your phone to the computer via the usb cable. pay attention and uninstall the usb device that appears when you hook up.
Then rescan. Reboot both the computer and the phone and see if that helps
sook said:
I've tried MrVanx' solution also, just forgot it in the original post. It seems to sync more often when the box is ticked anyhow.
I don't have a problem with hard reseting or flashing. I'm going through this hassle for the sole reason of flashing to schaps 4.31
Ill try that when i get home tonight
Click to expand...
Click to collapse
Before you try flashing make sure you have the Hard-SPL V7 bootloader installed.
You can flash without activesync tho.... activate the bootloader and connect your usb cable. If the tricolor screen indicates a usb connection then you can run the RUU wrapper, follow the usual steps and it should flash just fine.
You activate the bootloader by pressing and holding the "Power" and "OK" buttons and depressing the reset with your stylus (the OK button you use has to be the one next to the jog wheel)
I can't find my Hermes in device manager either. I'll try doing the flash through the bootloader i guess.
Did you try un-checking the "Enable Advanced Network Functionality" box as mentioned in Reply #1? That fixed it with mine. It would sync with my WinXP work PC, but not my WinXP Home pc, unchecking that box fixed it. Been fine ever since....
cyberscribe said:
You can flash without activesync tho.... activate the bootloader and connect your usb cable. If the tricolor screen indicates a usb connection then you can run the RUU wrapper, follow the usual steps and it should flash just fine.
Click to expand...
Click to collapse
do i have this correct?
1. enter bootloader
2. connect usb cable, check for confirmed connection
3. use ruuwrapper.exe to install hardspl http://www.mrvanx.org/cms/index.php...ask=view&id=52&Itemid=26&limit=1&limitstart=2
4. return to bootloader
5. connect usb cable, check for confirmed connection
6. use ROMupgrade.exe to install new radio http://www.mrvanx.org/cms/index.php...ask=view&id=52&Itemid=26&limit=1&limitstart=3
7. return to bootloader
8. connect usb cable, check for confirmed connection
9. use ROMupgrade.exe to install Schaps 4.31 http://www.mrvanx.org/cms/index.php...ask=view&id=52&Itemid=26&limit=1&limitstart=4
10. reboot ppc, delete partnership from pc activesync, cross fingers, sacrifice a goat, sync, install programs, bask?
JETninja said:
Did you try un-checking the "Enable Advanced Network Functionality" box as mentioned in Reply #1? That fixed it with mine. It would sync with my WinXP work PC, but not my WinXP Home pc, unchecking that box fixed it. Been fine ever since....
Click to expand...
Click to collapse
yup. tried it on the laptop that i use constantly with a legit copy of XP Pro. tried on BRAND NEW install of newest hacked version of XP Pro. neither were successful.
AT&T 8525 USN Syncing problem ...
I had the same problem too ... fortunately I had a simple fix.
I made sure that I only use the USB/mini-USB cable that came with my AT&T 8525. If I use a USB that came from a different device (like another phone or camera), it doesn't want to sync, except once in a blue moon.
The other USB cables may charge it, but won't sync it.
I've read elsewhere in this site that our 8525's can be picky with their pinouts on the USB, so this might be the issue. I hope it's something this simple for you!
Hope this helps!
it's a thought. ill dig through my drawer of cables and pull out all the usb/mini usb cables. no idea if I'm using the original or not.
however 6 mo ago when i gave up on the thing the first time i know it was the correct cable
sook said:
it's a thought. ill dig through my drawer of cables and pull out all the usb/mini usb cables. no idea if I'm using the original or not.
however 6 mo ago when i gave up on the thing the first time i know it was the correct cable
Click to expand...
Click to collapse
sometimes cables go flakey, but the cable we use is standard not proprietary so any A - miniusb cable should work.
Anyway the procedure you outlined above should have worked, am I to understand you still have the ATT ROM? If so talk to them about this problem.
If not access the bootloader again and hook up your usb cable. Does USB appear at the bottom of the screen?
Are you using the usb adapter that came with the phone? If not try to go back to that. The pinouts are the same as a miniusb but the form factor makes for a better fit and regular miniusb jacks can cause nonsyncs.
If you aren't getting "USB" at the bottom of the screen it is either a bad cable, a bad usb port (either at the comp or your phone), bad usb drivers, or just bad hardware in the phone. If any of these is the problem, all you can do is talk to AT&T hopefully before the warranty expires.
Sorry I wasn't more help mate.
The cable I've been using is the one that came with the phone. I tried the cable that came with my mp3 player and got the same results.
I do still have the out-of-the-box ATT Rom, however, the steps you outlined did not fix my problem. I did notice that my device appears as "HTC USB Sync" which I found strange. Is this normal?
USB does appear when I connect the phone in bootloader to the computer. I've tried two USB ports on two separate computers. Both computers are completely up to date with MS and drivers.
I suppose I'll go bother the people at ATT.
If I'm done with the ATT Rom, can I do all the flashing through the USB connection to the bootloader?
hey guys im having the same problem (TyTN II) it'll charge, but wont sync or show in device manager (i am using the original cable though)
i've tried to go into bootloader, but it doesnt say 'usb' at the bottom like it should, instead it says 'serial' i've tried diff usb ports, i've also unticked the advanced network box, softreseted, and hardreseted still no go...any ideas?? (im using alex's wm6.1 rom, could wm6.1 possibly have something to do with it?)
ActiveSync BOOSTER
Is there a way to boost up speed of Sync
Is there a any software or Cab file for it ?
Also want to know after we sync Phone
It keeps repeating to sync, is there a way to stop it ?
With removing the phone
Please Help
Sorry if I'm missing something really obvious but I've looked through the forums and the wiki for possible solutions to this.
I tried to upgrade the ROM to tomal - V8.0 (6.1 Pro). After syncing and going through the initial screens, Windows came up with a message that the attached USB device had malfunctioned on going into the bootloader. I've tried using the mtty utility in a few different computers but each time there is no USB option listed in the port. As it is, I'm stuck in the bootloader screen (showing "Serial" rather than "USB", v1.00) and softresetting just brings me back to the same bootloader screen again.
Does anyone have any ideas?
Hello bro,
Faced this problem few times...and got it to work .
What i did was removed SIM Card / MMC Card and disable Usb connection in active Sync and try not to use any HUB for usb and try all the Usb ports available on your computer. keep trying thats all i can say and i did.
Hope it works out for you good luck .
~ZODI.
Thanks for the reply. There's no SIM card or SD card inserted and I've tried all the USB ports on three different computers - one running XP, one running Vista Home and one running Vista x64. I've also tried running lsusb on a linux boot and nothing comes up on that (though in all honesty I don't know what it should be detected as).
progress?
Hi Steven,
any progress, I am having the same problem on my (new) universal. serial doens't change to usb whatever I do (tried mtty and everything)
Oh one other thing, When I retract my usb-cable halfway form my phone "usb" DOES appear, you think we could do sth with that?
Thanks and thanks to all on these great forums at xda!
Curehead
nope, sorry. i've never got any further forward.
Hi, i have a problem, my diamond doesn't connect to my pc anymore, not with active sync, not as a driver and not as a internet modem, i need to connect it so i can flash to a new rom to fixe a issue i have (my diamond freezes and does hard resets after that, all the time) to fix it i need to flash tock rom>hard reset>my rom>hard reset, but this won't work if i can't see a way to flash my phone ...
I'm not sure because I don't use XP, but do you not need WM Device Center or something?
And what format (wipe) memory to default from mobile, i mean main (not internal storage). i know that mobil will go to "preinstall" stadium...... if u dont undertand u lose everything on program memory (contacts, sms but u can backup it). If u do it u have clean rom because every rom have a shadow install copy.
there is no problem i thing
donald-c said:
I'm not sure because I don't use XP, but do you not need WM Device Center or something?
Click to expand...
Click to collapse
Thank you for your reaction! But no that's only necessary if your system is running Windows Vista.
Hysterian said:
And what format (wipe) memory to default from mobile, i mean main (not internal storage). i know that mobil will go to "preinstall" stadium...... if u dont undertand u lose everything on program memory (contacts, sms but u can backup it). If u do it u have clean rom because every rom have a shadow install copy.
there is no problem i thing
Click to expand...
Click to collapse
Thank you for your reaction too! No, you mean a hard reset, i allready did this a couple of times, the strange thing is that it doesnt work after a hard reset too, i allready backed my settings(contacts,sms,etc.) up since the problem started but it has no sence restoring it if it keeps auto hard-resetting itself...
Strange thing i noticed too is that when i connect my phone to the net adapter it thinks i'm connecting to a PC and it will ask me to chose an option(a.sync/file disk/ internet modem)
I dont know but my permanent problem is that every rom have checked faster data sync on usb sync and my vista doesnt recognize this... i dont know why is permanently enabled but for me this is not working.
but for u. it can be registry problem..... any registry cleaner or backup from other rom? just an idea
Hi, i have a problem, my diamond doesn't connect to my pc anymore, not with active sync, not as a driver and not as a internet modem, i need to connect it so i can flash to a new rom to fixe a issue i have (my diamond freezes and does hard resets after that, all the time) to fix it i need to flash tock rom>hard reset>my rom>hard reset, but this won't work if i can't see a way to flash my phone ...
Click to expand...
Click to collapse
Hi,
If you are using USB, you can try to change the USB port, here worked.
z10n said:
Hi,
If you are using USB, you can try to change the USB port, here worked.
Click to expand...
Click to collapse
Fysical port, COM port or Computer(allready done)
bump, this just became a major issue i downloaded diamimg.nbh to internal storage and flashed to default rom but my USB still is not working.. please someone help me out ?
maybe your USB Port is broken or dirty? you ever tried to clean it? (turn your phone off, remove the battery, take a needle and take all the dust and fluff/lint out)
can you charge your phone via usb?
I had the same problem with XP. Glad I have also a mac ;-)
I "solved" the problem by leaving the phone connected to USB and restarted the PC. Then it worked but only if leave it in USB. When you pull it of you have to do it again :-(
Hope that helps temporarly
lordcoffee
tomoffel said:
maybe your USB Port is broken or dirty? you ever tried to clean it? (turn your phone off, remove the battery, take a needle and take all the dust and fluff/lint out)
can you charge your phone via usb?
Click to expand...
Click to collapse
Yes i can, and if i connect my adapter to the net and put the mini usb in the phone a window will pop on my phone & tells me to choose disk drive/async/internet modem..
im now going to clean the usb port ands see if it helps, thank you for your reaction!
lordcoffee said:
I had the same problem with XP. Glad I have also a mac ;-)
I "solved" the problem by leaving the phone connected to USB and restarted the PC. Then it worked but only if leave it in USB. When you pull it of you have to do it again :-(, thank you for your reaction!
Hope that helps temporarly
lordcoffee
Click to expand...
Click to collapse
Seriously? i tried it on another XP and it didnt work either, ill try it and get back at you thanks!
willyy1991 said:
Yes i can, and if i connect my adapter to the net and put the mini usb in the phone a window will pop on my phone & tells me to choose disk drive/async/internet modem..
im now going to clean the usb port ands see if it helps, thank you for your reaction!
Click to expand...
Click to collapse
I have two charger, one ist the original from HTC, and the other is a normal plug with the miniusb on the other side, sometimes when I plugin the non-original I get the same message (USBtoPCPoppUp).
The reason is that not all pins have good contact, maybe you have to clean your usb connector with some "hard" cleaningstuff (alcohol(not the sweet stuff.. take it from a pharmacy!) or you can try rubbing alcohol (my favorite! ).
you could also try another USB cabel if you have one
I just purchased a Telstra Touch HD T8285 on eBay. Unfortunately, the seller did not disclose that he had flashed a new ROM (Dutty ROM) to it and that USB syncing and wifi do not work. I'd like to try and get this fixed on my own...otherwise I will have to try and get the seller to take the phone back and refund my money. I really like the phone so I just want it to work properly.
After much searching on here I discovered that I could flash directly from the flash card, thus bypassing the problem of USB syncing not working. I have tried a few ROMs (EnergyRom, Miri, Telstra updated direct from HTC) and neither wifi nor USB syncing works with any of them.
I have tried all the hints/suggestions about changing USB settings in activesync on both the phone and computer and nothing works. I cannot even get my computer to recognize the phone as a USB storage device (the phone just starts charging but activesync acts as though it's not even connected). When I go into bootloader mode on the phone it displays "serial" but never changes to USB.
Bootloader screen displays the following:
BLAC120 32M
SPL-1.56.Olinex
MicroP-Blackstone (LED) v6
From what I've read on here, I think I need to get a new version of SPL on my phone but I don't know how to do so without being able to use USB syncing. Is there any way to reflash SPL on my phone using the card flash method?
Someone please help!
gmischenko said:
I just purchased a Telstra Touch HD T8285 on eBay. Unfortunately, the seller did not disclose that he had flashed a new ROM (Dutty ROM) to it and that USB syncing and wifi do not work. I'd like to try and get this fixed on my own...otherwise I will have to try and get the seller to take the phone back and refund my money. I really like the phone so I just want it to work properly.
After much searching on here I discovered that I could flash directly from the flash card, thus bypassing the problem of USB syncing not working. I have tried a few ROMs (EnergyRom, Miri, Telstra updated direct from HTC) and neither wifi nor USB syncing works with any of them.
I have tried all the hints/suggestions about changing USB settings in activesync on both the phone and computer and nothing works. I cannot even get my computer to recognize the phone as a USB storage device (the phone just starts charging but activesync acts as though it's not even connected). When I go into bootloader mode on the phone it displays "serial" but never changes to USB.
Bootloader screen displays the following:
BLAC120 32M
SPL-1.56.Olinex
MicroP-Blackstone (LED) v6
From what I've read on here, I think I need to get a new version of SPL on my phone but I don't know how to do so without being able to use USB syncing. Is there any way to reflash SPL on my phone using the card flash method?
Someone please help!
Click to expand...
Click to collapse
It sounds more like you need to update your usb drivers by following this guide. Also ensure that you have enabled 'allow usb connections' in activesync connection settings.
Unfortunately you cannot change SPL without using your usb, so let me know if this works
unfortunately that guide to updating USB drivers does not work. When my phone is in bootloader mode the bottom only says "Serial". It never changes to "USB" so the computer does not even recognize that a device is connected.
gmischenko said:
unfortunately that guide to updating USB drivers does not work. When my phone is in bootloader mode the bottom only says "Serial". It never changes to "USB" so the computer does not even recognize that a device is connected.
Click to expand...
Click to collapse
Did you check that 'allow usb connections' was turn on in activesync connections settings?
Also when you update usb drivers you need to turn your pc off then on again.
Yes I made sure of that setting in ActiveSync.
Since my computer does not recognize my phone being connected, the "Windows CE USB Devices" is not listed in the Windows Device Manger. I have tried connecting my phone to 3 different computers (Windows XP and Windows 7) using different USB cables and still get nothing.
The closest I got was one time yesterday when I plugged my phone into the a/c adapter to charge, the USB window popped up on my phone asking whether I wanted to connect to ActiveSync, Storage Card, or Internet Sharing. That is the only time the window has ever opened and it wasn't even plugged into a computer.
gmischenko said:
Yes I made sure of that setting in ActiveSync.
Since my computer does not recognize my phone being connected, the "Windows CE USB Devices" is not listed in the Windows Device Manger. I have tried connecting my phone to 3 different computers (Windows XP and Windows 7) using different USB cables and still get nothing.
The closest I got was one time yesterday when I plugged my phone into the a/c adapter to charge, the USB window popped up on my phone asking whether I wanted to connect to ActiveSync, Storage Card, or Internet Sharing. That is the only time the window has ever opened and it wasn't even plugged into a computer.
Click to expand...
Click to collapse
ok, try going to to Start > Settings > Connections > USB to PC and ensure that 'ActiveSync' is selcted along with 'Enable faster data synchronization' and try again
Fallen Spartan said:
ok, try going to to Start > Settings > Connections > USB to PC and ensure that 'ActiveSync' is selcted along with 'Enable faster data synchronization' and try again
Click to expand...
Click to collapse
I've tried that as well.
Basically, if it's been written here on the forum I've tried it. Each thread I've found where someone has had the same problem seemed to fade off and no one reported back (even those that fixed it).
Possibly a hardware problem with your usb port then which would require a warranty return unless anyone else has any suggestions
EDIT
Try flashing original stock rom, i.e. the one which was on the device originally when bought. This rom will still flash even if bootloader says 'serial'. This is the only rom that this works for. Unfortunately in your case you do not know what this rom was so a bit of guess work will be required going by date and location. Stock roms are available in wiki here and it'll just be trial and error
Hi
Hello,
Unfortunately,I have the same problem With my HTC HD phone, I've tried every thing but i couldn't found a solution to my problem, in SPL stage the screen show me only Serial and hang on it ,and when i connect my phone to my PC not change to USB,
So please any one have a clue for this,
Thanks in advance.
Dear gmischenko,
Did you solve your problem??
I have tried changing the fast sync option
I have removed everything from the computer and re-installed.
I have hard reset my HD2.
I have restored my computer to before i bought the HD2 and let windows figure out that it needs to install WMDC - then let it download itself and install it.
I have tried every USB port on my computer and also bought a powered USB hub and tried that.
After all installs it just simply wont let me make a partnership or anything.
I don't know what to do anymore. I WANT ME SOME NEW ROMS!!!! please help me out. Other than things to get Windows 7 to work - is there a way to flash hardSPL2 / roms without USB?
I appreciate any help given and i have searched the forums here and all over the net. If i missed that one special trick that my computer needs i do apologize.
slowestcivic said:
I have tried changing the fast sync option
I have removed everything from the computer and re-installed.
I have hard reset my HD2.
I have restored my computer to before i bought the HD2 and let windows figure out that it needs to install WMDC - then let it download itself and install it.
I have tried every USB port on my computer and also bought a powered USB hub and tried that.
After all installs it just simply wont let me make a partnership or anything.
I don't know what to do anymore. I WANT ME SOME NEW ROMS!!!! please help me out. Other than things to get Windows 7 to work - is there a way to flash hardSPL2 / roms without USB?
I appreciate any help given and i have searched the forums here and all over the net. If i missed that one special trick that my computer needs i do apologize.
Click to expand...
Click to collapse
i dont know if its related but i have read that sometimes its the anti virus at fault (notably KASPERSKY)
slowestcivic said:
I have tried changing the fast sync option
I have removed everything from the computer and re-installed.
I have hard reset my HD2.
I have restored my computer to before i bought the HD2 and let windows figure out that it needs to install WMDC - then let it download itself and install it.
I have tried every USB port on my computer and also bought a powered USB hub and tried that.
After all installs it just simply wont let me make a partnership or anything.
I don't know what to do anymore. I WANT ME SOME NEW ROMS!!!! please help me out. Other than things to get Windows 7 to work - is there a way to flash hardSPL2 / roms without USB?
I appreciate any help given and i have searched the forums here and all over the net. If i missed that one special trick that my computer needs i do apologize.
Click to expand...
Click to collapse
I had the same problem with Win 7, however when I unchecked the faster connection option on HD2 it connected, although in Win7 it had a red x in mobile connection, but on the HD2 a connection had been established.
is formatting your PC an option?
Firewall?
I have three Windows 7 machines (32 & 64) and all connect without any problem. Disconnect from your internet connection. Turn off your anti-virus and firewall and give it a shot. Do you get the window that asks how you want to connect when you plug in your cable? Do you have a functioning cable? Just because it charges does not mean it will connect for data. Will it connect to an XP machine?
slowestcivic said:
I have tried changing the fast sync option
I have removed everything from the computer and re-installed.
I have hard reset my HD2.
I have restored my computer to before i bought the HD2 and let windows figure out that it needs to install WMDC - then let it download itself and install it.
I have tried every USB port on my computer and also bought a powered USB hub and tried that.
After all installs it just simply wont let me make a partnership or anything.
I don't know what to do anymore. I WANT ME SOME NEW ROMS!!!! please help me out. Other than things to get Windows 7 to work - is there a way to flash hardSPL2 / roms without USB?
I appreciate any help given and i have searched the forums here and all over the net. If i missed that one special trick that my computer needs i do apologize.
Click to expand...
Click to collapse
Have you tried a different usb cable? That's the only other thing I can think of that might be the problem.
HD2 on Windows 7 Ultimate
Hi
Had the same problem, and it turned out that the USB-cable i used, was the problem.
I used the cable that followed the 12v Car Charger, and that did no good, so I went and got the cable that came in the package (chargercable) and then it was Christmas and halloween alltogether.
Works like a charm!
@djchubbs yes i have turned that off as well - along with windows firewall
@ozkaya - no formatting my pc is not an option
@johnboatcat - When i plug it in the phone instantly asks me what kind of connection i want (file transfer or active sync with the checkbox option for faster sync as well). It transfers files just fine in file transfer mode as well.
@zarathustrax i have not tried a different USB cable as i dont have access to one. I doubt something is wrong with mine however i will have to see if i can get one somewhere.
@kongsvada Only cable i have is the one that came in the box factory from HTC
Again thank you for all the replies! I really really am trying to get this to work. I have my home computer which i do everything on but i tried my friends laptop today - it has the same exact build of windows 7 on it as my home computer (if that matters) and it will not sync or let me make a partnership or anything. I plugged it in, it downloaded WMDC and installed etc, restarted the computer and plugged it in, went to active sync mode and WMDC or the sync center do not recognize it at all. Since i cant find it in sync center i cant create a partnership.
slowestcivic said:
I have tried changing the fast sync option
I have removed everything from the computer and re-installed.
I have hard reset my HD2.
I have restored my computer to before i bought the HD2 and let windows figure out that it needs to install WMDC - then let it download itself and install it.
I have tried every USB port on my computer and also bought a powered USB hub and tried that.
After all installs it just simply wont let me make a partnership or anything.
I don't know what to do anymore. I WANT ME SOME NEW ROMS!!!! please help me out. Other than things to get Windows 7 to work - is there a way to flash hardSPL2 / roms without USB?
I appreciate any help given and i have searched the forums here and all over the net. If i missed that one special trick that my computer needs i do apologize.
Click to expand...
Click to collapse
OK, let me help you on this if flashing a new ROM will be your immediate task.
1) Just download the ROM that you like and rename it to LEOIMG.nbh
2) Make sure you've HSPL your LEO first.
3) Copy the renamed file into the root of your memory card.
4) Press the VOL down button simultaneously while turning ON your LEO.
5) Just follow the onscreen instructions on your LEO.
6) That's it.
the only problem that I can sense for you now is to HSPL your device because it does require connection with your PC. To bypass this connection with PC thing, do this;
a) Turn OFF your LEO.
b) Turn ON while pressing the VOL Down button together and it will enter the bootloader mode (TRICOLOR Screen).
c) At the bottom of your LEO, it will says "serial"
d) Now, connect the cable to your LEO and and your PC, the words will change to "Usb"
e) Let your PC do its work by installing the necessary driver automatically.
f) When it is done, run the HSPL program your PC. You can download it from this wonderful forum (Please search for it in the ROM development section)
g) Let the program finish and you can see something on your LEO screen in the process. Just look at it and let it finish. DO NOT TURN OFF YOUR LEO (I don't want you to brick your device).
h) When everything is done, reset your LEO and this time press the VOL Down button. This is to go back to the bootloader mode and to check whether the HSPL has been install correctly.
i) then go back to the steps (1 to 6) above to flash your new ROM.
Enjoy,
please post your result and help others too.
regards,
morisa
I had the same problem with my new computer which happend to be running windows 7 (everything was fine on my old xp machine). After much searching and trouble shooting the problem eventually came down to a setting on the motherboard (something to do with the p55 chipset). After I'd turned the c-state option on in the bios I've had no further issues.
It's a long shot but perhaps it will help you too
ok this sounds promising - i will try it this weekend when i have the time - i greatly appreciate the help and i will post results to let everyone know!
thank you all and like i said - will be trying your way soon mmorisa!
I had to change a registry setting on Windows 7 to get it to connect to my HD2... Of course I cant remember the setting, it may be this one
forum.xda-developers.com/showpost.php?p=3942556&postcount=7
mmorisa said:
OK, let me help you on this if flashing a new ROM will be your immediate task.
1) Just download the ROM that you like and rename it to LEOIMG.nbh
2) Make sure you've HSPL your LEO first.
3) Copy the renamed file into the root of your memory card.
4) Press the VOL down button simultaneously while turning ON your LEO.
5) Just follow the onscreen instructions on your LEO.
6) That's it.
the only problem that I can sense for you now is to HSPL your device because it does require connection with your PC. To bypass this connection with PC thing, do this;
a) Turn OFF your LEO.
b) Turn ON while pressing the VOL Down button together and it will enter the bootloader mode (TRICOLOR Screen).
c) At the bottom of your LEO, it will says "serial"
d) Now, connect the cable to your LEO and and your PC, the words will change to "Usb"
e) Let your PC do its work by installing the necessary driver automatically.
f) When it is done, run the HSPL program your PC. You can download it from this wonderful forum (Please search for it in the ROM development section)
g) Let the program finish and you can see something on your LEO screen in the process. Just look at it and let it finish. DO NOT TURN OFF YOUR LEO (I don't want you to brick your device).
h) When everything is done, reset your LEO and this time press the VOL Down button. This is to go back to the bootloader mode and to check whether the HSPL has been install correctly.
i) then go back to the steps (1 to 6) above to flash your new ROM.
Enjoy,
please post your result and help others too.
regards,
morisa
Click to expand...
Click to collapse
This worked great! I knew about bootloader screen, i knew i could flash from the SD card but i didn't know how to put them together. Thank you very very much for the help, now off to flashing roms!
One simple - probably stupid question:
I have seen TMOUS compatible on a few roms, however i will then read for that same rom that it is 576 ONLY - And then in another rom thread i see the creator of the rom say TMOUS compatible and then "TMOUS=1024". So what one is it!? just trying to be safe
Again - thank you all so much for the help - i really appreciate everyone that tried to help!
Edit: Just flashed the Evo rom to the phone, plugged it in and BAMN im able to sync with WMDC immediately - so thank you all so so much - super happy now with my 1024 leo!
slowestcivic,
I feel happy that you managed to do it and flash your favorite ROM with the guides I wrote.
at least i can see another smile from another happy LEO user.
best regards and don't forget to help others too.
mmorisa
slowestcivic said:
@djchubbs yes i have turned that off as well - along with windows firewall
Again thank you for all the replies! I really really am trying to get this to work. I have my home computer which i do everything on but i tried my friends laptop today - it has the same exact build of windows 7 on it as my home computer (if that matters) and it will not sync or let me make a partnership or anything. I plugged it in, it downloaded WMDC and installed etc, restarted the computer and plugged it in, went to active sync mode and WMDC or the sync center do not recognize it at all. Since i cant find it in sync center i cant create a partnership.
Click to expand...
Click to collapse
Also running Office 2010 beta can cause active sync issues
yeah i have 2007 outlook so that wasnt thr problem. Still not sure what was wrong with it but after flashing a new rom all is well
I had the same trouble with win7. What i did after i tryed evrything i could think of was dowloading the latest active sync from Microsoft. Restarted and plugged the phone in and it worked