Database Users

flashing new radio, now lost 2g/3g data?!

I had cm7.0.3 running ok with radio:
October 2010: Radio_12.28b.60.140e_26.03.02.26_M - HTC WWE 1.32.405.6
I followed the instructions here:
http://forum.xda-developers.com/showthread.php?t=896597
to flash recommended radio:
4th January 2011: Radio_12.28e.60.140f_26.04.02.17_M2_SF - HTC WWE 1.72.405.3 R2
I'm not sure if it was because I didn't wipe but everything since was very jerky and the device was unresponsive, therefore I reverted to an older ROM I had backed up. Now I have found that I no longer have a 2g/3g data connection, the phone just states "unknown" within my quicker app settings.
Does anyone know why I've had this problem, or better still any ideas how I can resolve?

Punch in *#*#4636#*#* into your keypad and head into Phone Information.
What info is displayed? You may need to type it all out.

Cool, thanks for this info.
Right I have followed your instructions and before I write everything out I have notice that at the bottom of the first menu (which is: Phone info) the "set preferred network type was set to "WCDMA preferred", am I right in saying I should change to "GSM only" or "GSM auto (PRL)?

Mine is set to WCDMA preferred and I get 2G/3G/H. Try it, you have nowt to lose at this point.

Ok, changing that doesn't seem to have worked. I lost regular phone signal.
Phone info for you:
IMEI: xxxx
phone number: unknown
current network: orange
signal strength: -99dBm 7 asu
location: LAC = c32 CID = c32adb2
neighbouring CID: no neighbouring cells
roaming: not roaming
GSM service: in service
GPRS service: Discountinued
network type: UMTS
message waiting: false
call redirect: false
call status: idle
radio resets: 0
data attempts: 0
data success: 0
GSM disconnects: =========DATA==========
State: DcInactiveState
disconnected with last try
at 12:59 AM
fail because No Error
PPP sent: 0 pkts, 0 bytes
PPP received: 0 pkts, 0 bytes
Number of PPP reset since boot: 0
Set preferred network type:
WCDMA preferred
Does this help you at all? Thanks, appreciating your support.

It does a bit. GPRS service reads "Discontinued". If you had disabled data on your phone it would read "Disconnected".
What I would do is try the same SIM card in another phone. If you cannot try that you can check your APN settings.
Settings > WiFi & networks > Mobile Networks > Access Point Names > check you have the correct settings.

I can't try the SIM card part until tomorrow.
Prior to leaving work today I did check my phones APN settings against a work mates (since he has an unrooted DHD) and they appeared correct. Both phones has two Orange UK (-orangeinternet) and Orange UK MMS (orangemms).
I removed the SIM and battery and then re-assembled.
I have been changing things and then checking, now it states the following (with regards to the list I provided you earlier):
Phone Number now appears
GPRS service now states disconnected
and the GSM disconnects still states:
=========DATA==========
State: DcInactiveState
disconnected with last try
at 12:59 AM
fail because No Error
PPP sent: 0 pkts, 0 bytes
PPP received: 0 pkts, 0 bytes
this is all with "WCDMA preferred"
I have also re-flashed with the radio that was previously in the phone (26.03.02.26), but still no data connection...

The only sure fire way to find out if its your setup is to run the 1.32 RUU and flash back to stock. If you get data then its your system / radio / RIL setup.
If you flash back to 1.32 you can be fully rooted / S-OFF / etc again in about 1 hour.

Ok, thanks for that.
Just to provide a little more detail:
I had to downgrade before rooting to CM7-RC4, then I moved to CM7-final, CM7.0.2 and then CM7.0.3 before I decided to upgrade my radio from 26.03.02.26 to 26.04.02.17.
This is when I hit my data problem.
Since then reverted to an older ROM backup and I have re-flashed different radio's to see if it would come back to life.
I have now applied the CM7.1 update (since I guessed I have nothing to lose).
Tomorrow I will try and make time to drop to 1.32 RUU.
Am I right in saying the RIL is the tie-in between the software and the radio? It sounds like this might be my problem now?
I'll need to research the procedures to do what you suggest since I'm still pretty new to all this...
Thanks again, I'll let you know how I get on.

Yes you are correct the RIL sits between the Radio and software.
An incorrect RIL could be the cause. Have you tried flashing the recommended RIL?

Ok, thanks.
I have some time now to play with this, would you happen to know if it matters which order I do this in?
radio, RIL, then ROM?

Sorry for that, I found the answer to my own post, RIL last!

I have now re-flashed radio:
Radio_12.28g.60.140f_26.05.05.27_M3
and then applied RIL (using ROM Manager):
HTC-RIL_2.2.0099HM
Still had no joy.
Ran the 1.32.exe application to return to stock (it informed me that it was changing 2.36.405.8 to 1.32.405.6) and my data has returned! My voicemail icon has returned too!
Would be ace to have these with CM7!
Any suggestions on the quickest and more reliable way to get to CM7?
1. flash newer radio
2. test vm & data connection
3. flash cm7

Just to let you know that after flashing radio vm and data still worked and then going onto cm7.0.3 my data still works - fixed! Although, I have lost my voicemail Still happy though, thanks for your suggestions.

got 7740 mango update by debranding

hi,
Today morning, i tried changing the following registry key .
Once i restarted the mobile, i got the updates notification for 7740 instantly.
MobileOperator: VOD-DE
MOName: Vodafone
OEMDeviceName: Atlantic_VDF_DE
anyhow, there is no Wifi tethering in this update.

What's new in this update?

Notice battery life improvements or anything?

It was said to fix the exchange server problem and some improvements in voicemail.
Not even 24 hrs since i installed the update.
Will keep posted if i see any battery improvements.

7740 supposed to have some improvement for battery according to this:
http://www.winrumors.com/nokia-promises-second-windows-phone-update-for-battery-issues/
Just did the changes as the OP suggested and I triggered the 7740 update. Interestingly, it says there is also "LG Update for Windows Phone", OP did you see this too?
Hoping it is for tethering .... updating now, will report when done.
Just in case anyone needed debranding instructions:
1. Enable the MFG application by going to the dialer and dialing ##634# then pressing call.
2. Launch the MFG application and enter 277634#*# when prompted for a password.
3. Select the Engineer Menu item.
4. Select the Other Setting menu item.
5. Select the Edit registry menu item.
6. Set the input boxes on this menu as follows:
Select ROOT_PATH: HKEY_LOCAL_MACHINE
Input SUB_PATH: \System\Platform\DeviceTargetingInfo\
Input KEY: MobileOperator
Data Type: STRING
7. Select Query and write down the result in case you need to re-brand for some reason.
EDIT:
Installation failed after rebooting phone, error code 8018001e, did not update to 7740.....did not do LG update...
EDIT 2:
Tried to update it a couple more times, but always getting the error... OP what kind of Quantum do you have and what carrier ROM? C-900? c-900B? c-900k?

can you tell me the registry changes you did ?
What mobile operator did you put in ?

I finally managed to update.
I think battery might be slightly better but that could be placebo lol
Anyway keeping current is always good anyway

I tried vod de and also vod it. Both showed there was 2 updates, but always failed. Op and scoobysnacks, what model of quantums are you using?

dont do ir his way, use the update cab sender here
http://forum.xda-developers.com/showthread.php?t=1306415
Much easier

Thanks, the cab sending method worked. I'm still interested in what carrier your phone was originally with

bobzero said:
Thanks, the cab sending method worked. I'm still interested in what carrier your phone was originally with
Click to expand...
Click to collapse
mine is a bell phone I'm using with telus

yakaaithiri said:
hi,
Today morning, i tried changing the following registry key .
Once i restarted the mobile, i got the updates notification for 7740 instantly.
MobileOperator: VOD-DE
MOName: Vodafone
OEMDeviceName: Atlantic_VDF_DE
anyhow, there is no Wifi tethering in this update.
Click to expand...
Click to collapse
Just a note -- if you truly 'debrand' by changing the MobileOperator to " " (blank), then you don't get the upgrade right away. It seems to be region specific.

Official 7740.16 update notices have been getting sent out over the last week to Bell phones.
No firmware update accompanied this OS update.
Just for reference in case anyone wanted to brand their phone to Bell or ATT:
AT&T
[HKLM\System\Platform\DeviceTargetingInfo\]
MobileOperator = ATT-US
MOName = AT&T Wireless
OEMDeviceName = PACIFIC_ATT_US
BELL
[HKLM\System\Platform\DeviceTargetingInfo\]
MobileOperator = BEL-CA
MOName = BELL
OEMDeviceName = PACIFIC_BEL_CA
Other keys that can be adjusted and have an impact:
FirmwareRevision
RadioSoftwareRevision
MODeviceName

[Q] AuroraICS dataconnection problem!

So I have AuroraICS (version 1.11) and everything else is working nice, but no data connection. My service provider is Saunalahti which works in Elisa's network. I have data in roaming on, but nothing. I also tried to add manually Apn-settings but when I press "save" nothing happens, there's only a blank screen. So can someone please help me with this issue?

I have same problem
I have the same problem.
http://forum.xda-developers.com/showthread.php?t=1492957
I read from there, that i should:
Users in Finland on the Saunalahti network need to change a couple of settings for the sim card to load correctly.
download a terminal program such as connectbot and open a local session, then type:
su
setprop persist.opl.enabled 0
setprop persist.pnn.enabled 0
But it didn't help anything. Anyone could help? And i have six years old 'Kolumbus' Sim card, and with 2.2 it worked perfectly.
And also, i didn't flash 2.3 to my Huawei. I flashed straightly from 2.2.1 to 4.03

working now
Thanks a lot! I put these:
setprop persist.opl.enabled 0
setprop persist.pnn.enabled 0
and now it's working, saunalahti internet showed up in apn-settings.

Latest builds are better
As of version 1.10 it seems to work. Version 1.11 has yet another fix for us saunlahti users.

reply
So what is that another fix? or do i need to downgrade to 1.10?

on and off
Sorry, didn't realize you've had 1.11 already. I started with 1.9 and 3g basically wasn't working there. I've upgraded to 1.10 and it started working, pretty much. For much of this week it was running just fine and i was convinced that it was fixed, but today it was off again.
I sure miss all the network data icons 'g' 'e' '3g' 'h' from older roms. And for the record didn't need to set the APN, it got picked up automatically.

[Q] How to update/flash/dump touchscreen firmware

Hi all,
I got problem with touch screen on my china phone - it happens when i flashed newer official ROM - after flash everything works nicely ... but as i am working with phone it freezes, vibrates and reboots and after that the touch is completely screwed up. From my perspective it looks like something suddenly changed Calibration or firmware of touch screen (the flash of backup/another ROMs didn't help)
only thing i found on this topic is here but it is for specific tablets:
modaco.com/topic/355021-most-touchscreen-issue%E2%80%99s-explained-and-the-reason-some-touchscreens-are-dying-on-p10an01%E2%80%99s-advent-vega-viewsonic-10s-point-of-view-mobii-ect/
From android i floked up for files but they didn't contain any calibration for screen so i am assuming these data are saved in touch firmware.
source.android.com/devices/input/touch-devices.html
in *.idc i got
qwerty.idc
touch.deviceType = touchScreen
touch.orientationAware = 1
keyboard.layout = qwerty
keyboard.characterMap = qwerty
keyboard.orientationAware = 1
keyboard.builtIn = 1
cursor.mode = navigation
cursor.orientationAware = 1
needrom.com/download/star-n9002-mt6582 -This is my phone and ROMs i FLashed
Did anybody encounter touch issues ?
Any ideas or suggestions ?
Is there any possibility to calibrate it in android ?
Thanks, any idea or suggestion will be deeply appreciated

[ Solved ]Bluetooth share stop on CATS60 rooted

Hi guys,
My device is cat s60 ,Its on Android 6.0, last week I trying to root this device with magisk very easy and fast , everything is good ,as always Im going to installed root apps and play with aps, I install automate and download some scrips , finally I want to wrote my own script and it's about location and airplane mode , after some on and off airplane mode my Bluetooth share stop working and story was began ,my Bluetooth doesn't work yet and it's stop working , here list of works I do for fixing but no chance:
* Clear data and cache of Bluetooth
*Going to data/misc/bluedroid/ no file is here !!!! Like bt_config.xlm and ...
*Installed some apps that fix Bluetooth but no chance ,
any one have the same issue that can help me ,
I can't clear cache and wipe data ,Im trying to find some ways to fix this.
Thanks ,sry for my bad English
so after some searches i figure out my bt_config.conf , witch located in data/misc/bluedroid/ is gone , so i start to install from beginning my stock rom and then go to root files and see my config , thats the config of bt_config.conf i think when somebody have this problem can find his btMAC address on adb
adb shell settings get secure bluetooth_address
Click to expand...
Click to collapse
and then edit this file and Bluetooth error should gone .
[Adapter]
Address = your mac address
LE_LOCAL_KEY_IRK = 08a24df17b24b171021247948e3e2980
LE_LOCAL_KEY_IR = df2ca4f10c634bfa312ace86ec588864
LE_LOCAL_KEY_DHK = d234027d21a40e96302b60a1114be78a
LE_LOCAL_KEY_ER = 05502a73411b9d652e16fa6d189b1b9d
ScanMode = 1
DiscoveryTimeout = 120
[AutoPairBlacklist]
AddressBlacklist = 00:02:C7,00:16:FE,00:19:C1,00:1B:FB,00:1E:3D,00:21:4F,00:23:06,00:24:33,00:A0:79,00:0E:6D,00:13:E0,00:21:E8,00:60:57,00:0E:9F,00:12:1C,00:18:91,00:18:96,00:13:04,00:16:FD,00:22:A0,00:0B:4C,00:60:6F,00:23:3D,00:C0:59,00:0A:30,00:1E:AE,00:1C7,00:80:F0,00:12:8A,00:09:93,00:80:37,00:26:7E,00:26:e8
ExactNameBlacklist = Motorola IHF1000,i.TechBlueBAND,X5 Stereo v1.3,KML_CAN
FixedPinZerosKeyboardBlacklist = 00:0F:F6
PartialNameBlacklist = BMW,Audi,Parrot,Car
Click to expand...
Click to collapse