Before I get started, I already know that AT&T and TMobile are using different UMTS bands and that's why the G1 won't work on AT&T's 3G network. I've read many threads on this topic.
But...
I saw this...
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
...in another thread and it really got me wondering. The two Avago chips seem to control the frequecy used. What if one were to replace the ACMP-7381 with an ACMP-7331-TR1 and also replace the ACMP-7391 with an ACMP-7311-TR1? I checked the datasheets (available on the Avago website) and they all seem to be pin compatible.
Would I be willing to try it? Ummm... I don't know! I'm just curious if anybody else has any thoughts or comments?
So you want to carefully unsolder the chip and solder another, then pray it doesn't cause some problems with the logic circuit and finally spend lots of time messing with the phones firmware. Just to get 3G speeds where you already can get edge speeds.
If you want to do it as a project to see if you can, then I say cool, but if you are doing this just for 3G speeds on the AT&T network, then I think it's pointless, especially with the massive 3G rollouts T-Mobile is now doing.
i will post photos of the Canadian htc dream circuit board in a few hours.
I am VERY interested! I had my G1 on at&t with EDGE but finally switched to T-mobile for 3G with unimpressive results. I would be hesitant to try since Ive never messed with these components but I was able to do the LED soldering mod to my Samsung and Nokia back in the day and made a few circuit boards in school. I definitely think I could physically complete the hardware swap its just what happens next that Im worried about. lol
What if the component your swapping has a different Ω rating? This could undervolt or even worse burn out other components. Now were talking about adding resistors or possibly removing other ones already exsisting on the board. Not to mention that this board is SMT (surface mount), meaning there aren't any solder points on the bottom and the components don't have pins unless they are heavy and then they are only little plastic stabilizers.
You're looking at much more cost and hassle than it's probably worth.
Also, would the stock antenna work with the different frequency?
crapy pics
THE ONE WITH THE BLUE DOT IS THE ROGERS DREAM (the other one is t-mobile G1)
sorry that i didn't have a good camera but i tried..
gallery:
http://img26.imageshack.us/gal.php?g=1000387n.jpg
direct links:
http://img26.imageshack.us/img26/2493/1000387n.jpg
http://img196.imageshack.us/img196/1443/1000391xhu.jpg
http://img266.imageshack.us/img266/5339/1000392.jpg
http://img198.imageshack.us/img198/6840/1000395k.jpg
http://img40.imageshack.us/img40/2313/1000403h.jpg
http://img197.imageshack.us/img197/1760/1000409k.jpg
http://img26.imageshack.us/img26/434/1000410o.jpg
http://img40.imageshack.us/img40/2037/1000411x.jpg
http://img23.imageshack.us/img23/2975/1000412jlh.jpg
http://img200.imageshack.us/img200/5475/1000413u.jpg
http://img19.imageshack.us/img19/2125/1000414w.jpg
http://img31.imageshack.us/img31/449/1000415.jpg
http://img37.imageshack.us/img37/3241/1000417i.jpg
http://img200.imageshack.us/img200/6424/1000420v.jpg
SiXiam said:
If you want to do it as a project to see if you can, then I say cool, but if you are doing this just for 3G speeds on the AT&T network, then I think it's pointless, especially with the massive 3G rollouts T-Mobile is now doing.
Click to expand...
Click to collapse
Yeah... I guess I'm just a tinkerer at heart! I'm really not that unhappy with edge speeds most of the time.
aggtrfrad said:
i will post photos of the Canadian htc dream circuit board in a few hours.
Click to expand...
Click to collapse
woot! Very interested to see those photos. Doh! Posted them at the same time I replied!!
SiXiam said:
What if the component your swapping has a different Ω rating? This could undervolt or even worse burn out other components. Now were talking about adding resistors or possibly removing other ones already exsisting on the board. Not to mention that this board is SMT (surface mount), meaning there aren't any solder points on the bottom and the components don't have pins unless they are heavy and then they are only little plastic stabilizers.
Click to expand...
Click to collapse
I come from a computer engineering background. I know all about surface mount components and how difficult soldering can be. I could pour over the datasheets a bit more if I decide to pursue this any further and even speak to a rep from Avago. I'm more concerned about the software at this point. I'm wondering if I would need to make firmware changes?
breaultm said:
You're looking at much more cost and hassle than it's probably worth.
Also, would the stock antenna work with the different frequency?
Click to expand...
Click to collapse
Don't know about the antenna, but I doubt the cost of those two ICs is gonna break the bank. Ya know?
Thanks for the replies... Anybody have any thoughts on the firmware?
aggtrfrad said:
THE ONE WITH THE BLUE DOT IS THE ROGERS DREAM (the other one is t-mobile G1)
sorry that i didn't have a good camera but i tried..
gallery:
http://img26.imageshack.us/gal.php?g=1000387n.jpg
Click to expand...
Click to collapse
BOOYAH!! See, it's right there! Those two small ICs in the upper left-hand corner: Avago 7311 and Avago 7331!
Ok, so I compared the two boards a little closer. The board itself appears to be the same. The two Avago chips are the same as I originally suggested. However, several of the smaller resistors and/or capacitors appear to be different. I bet this mod is theoretically possible, but it's probably more trouble than it's worth.
wow hmmm tell me if it works if you solder it right
i too have been thinking about this, but i am not gonna take apart the G1 again, it was enough of a hassle keeping that damn void sticker from breaking. i have a few phones that are compatible on ATT 3G and t-mobile 3G and thought about switching the cips, but i don't think i am up for the challenge. my 8525 has been apart for almost a year and a half now and i lost most of the screws so it's in a box waiting for me to come up with some project for the parts
Related
hello, i have had an 8525 since december and it has been great. except the other day i was going to charge my phone but i saw that the connector was messed up, and i have no idea how it got that way cuz my phone has zero scratches and hasn't been dropped. i tried using a 2mm flathead to fix it but it didn't work and i was scared to use a lot of force because i don't want to cause anymore damage. any help would be appreciated, thanks.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Will examine internally later today but meatime you do not say if it still works.
Mike
my did the same !
I have the same problem my one completely broke after messing around trying to fix any help would be appreciated
Ouch. :/ .......
mikechannon said:
Will examine internally later today but meatime you do not say if it still works.
Mike
Click to expand...
Click to collapse
thanks for the reply, and yes the phone still functions perfectly. i turned it off though so i can save it for an emergency, as i do not have a backup phone.
Above we can see:
1
The rear view of the USB connector
2
That re-soldering will not be possible. This is a multi-layer board and these components are not part of or soldered to the USB Connector.
Above we can see:
1
The top of the USB housing and it's anchoring (possibly earthing also) soldering.
2
Soldering would be possible here to re-do the anchoring solder joints. This would be worthwhile if the connections are still in tact and the purpose is merely to re-anchor the housing.
Another view above of one of the anchor joints. Caution should be used not to dissipate excessive heat through the board - given its multi-layer nature and components on the reverse side.
Mike
EDIT:
In baller4ever85's picture it looks like one side only has come adrift and it may just require the anchoring joint to be re-soldered - but that assumes the contacts are still fine otherwise.
^thanks for the detailed pics. i don't have any experience with soldering. will htc repair it? my phone is also still under warranty w/at&t so i will see what they can do(probably not much).
I had this problem to the point I could not Sych or power the phone. I called at&t and it was replaced under warranty repair. It was replaced with an at&t branded 8525.
In the FWIW department... I did call HTC prior to calling at&t. Since this is a mother board repair item, minimum charge to look at the phone was quoted as $245!!! Thus the call to at&t.
If you can't get it fixed, I'll buy it.
dbltap said:
I had this problem to the point I could not Sych or power the phone. I called at&t and it was replaced under warranty repair. It was replaced with an at&t branded 8525.
In the FWIW department... I did call HTC prior to calling at&t. Since this is a mother board repair item, minimum charge to look at the phone was quoted as $245!!! Thus the call to at&t.
Click to expand...
Click to collapse
thanks a ton for that advice. im gonna give them a call today, because its so frustrating not having a phone.
dbltap said:
I had this problem to the point I could not Sych or power the phone. I called at&t and it was replaced under warranty repair. It was replaced with an at&t branded 8525.
In the FWIW department... I did call HTC prior to calling at&t. Since this is a mother board repair item, minimum charge to look at the phone was quoted as $245!!! Thus the call to at&t.
Click to expand...
Click to collapse
well i called at&t and they said i could do a warrnaty exchange but the rep told me i would most likely be charged $500
so i guess im not sure what to do.
baller4ever85 said:
well i called at&t and they said i could do a warrnaty exchange but the rep told me i would most likely be charged $500
so i guess im not sure what to do.
Click to expand...
Click to collapse
That must be because they replace the entire board. A bit different from here:
http://www.pocketpctechs.com/main.a...9&area=repairs-full+service&item=75H00465-10M
Mike
This is a question for those familiar with the innards of the HTC phones.
Do you think it would be possible to put a Hero's radio inside of an Evo, thus making a 3G-only "Hevo" that has the horsepower of an Evo but the 3G-only radio of a Hero?
Obviously, this would take some expertise -- perhaps some work with a reflow machine or something of that nature to actually move the tiny chip -- but is there one single chip that could be physically swapped which would essentially change the ESN on a phone?
If the chip was physically swapped, would this have any chance of working from a technical standpoint? Could an Evo function if it had the radio of a Hero? If not with a stock ROM, perhaps with a third-party ROM?
Thoughts?
To what end? How is that different than just turning off 4g?
Sent from my blah blah blah blah
I have no idea but I just wanted to ask.... why? I don't think this one deserves an answer of "because we can" either.
imekul said:
This is a question for those familiar with the innards of the HTC phones.
Do you think it would be possible to put a Hero's radio inside of an Evo, thus making a 3G-only "Hevo" that has the horsepower of an Evo but the 3G-only radio of a Hero?
Obviously, this would take some expertise -- perhaps some work with a reflow machine or something of that nature to actually move the tiny chip -- but is there one single chip that could be physically swapped which would essentially change the ESN on a phone?
If the chip was physically swapped, would this have any chance of working from a technical standpoint? Could an Evo function if it had the radio of a Hero? If not with a stock ROM, perhaps with a third-party ROM?
Thoughts?
Click to expand...
Click to collapse
With enough money I'm sure anything is possible but you have programming that might correlate with or to that radio. Just like the issue with HTC putting a different camera in the Evo is causing some problems. Imaging swapping a radio what kind of problems you would encounter. Sounds like a major pain the the a$$ with a huge probability that it would not work. Not to mention that is one reason the Evo is the $h1t because it has 4G.
i think the answer is NO. sounds to me that someone doesn't want to to pay for 4g service. i agree the extra $10 sucks because where i live i don't have 4g. but im not going to frakenstein my evo either.
Different chips with different pinouts... Never happen.
sent from my Evo 4G using Taptalk
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
xHausx said:
Click to expand...
Click to collapse
hahahaha. thats too funny.
xHausx said:
Click to expand...
Click to collapse
my favorite quote
To me it sounds like the OP wants to move the radio chip from his Hero so that he can sort of clone his Hero's ESN. I'm no expert on the subject, but I think a standard cloning procedure would be a lot easier.
FWIW, the chip on the Evo's motherboard that handles 4G/WIMAX is separate from the 3G radio chip. It's the Sequans SQN1210. I suppose if you're really that desperate to get away from the $10/month "4G fee" (that's not really just for 4G) then you could desolder it from the motherboard and then take it up to a Sprint store and see if you can get them to remove your premium data fee from your monthly bill. While you're at the store, ask for the 10% S.T.U.P.I.D. discount.
P.S. the 3G radio in the Evo is actually included in the QSD8650 chip. Yes, this chip includes the main CPU, GPU, CDMA radio, and even a GSM radio. To do this swap, you'll need to use a lot of extra solder.
Am i the only one thats thinking there is something amiss with this question? i can't imagine any LEGAL reason someone would want to swap chips out with an old phone.
SilverStone641 said:
Am i the only one thats thinking there is something amiss with this question? i can't imagine any LEGAL reason someone would want to swap chips out with an old phone.
Click to expand...
Click to collapse
Yup, he either found, stole, or bought a flagged EVO and is trying to use it.
Sent from my PC36100 using Tapatalk
There are much easier ways to clone an ESN than swapping chips.
Just got my hand on a Korean Samsung Galaxy S II. Found a NFC option under Setting menu. Then i removed the back cover, and found the NFC logo on the battery??!!? Could it be the battery is where the NFC tag is at?
Pics:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Phone manufactured date: 2011-04-26
Image took with my old Nexus One.
What do you guys think?
Interesting
This is super interesting! From your pics I see that the phone has 4 connector pins, how many does the battery have? How many does the Indian battery have? I am inclined to believe this is the mystery behind "Optional NFC".
It would be interesting to see some side on shots compared to a standard SGS II - I hear the NFC version is somewhat thicker?
AFAIK, the KOREAN SGS2 had NFC since launch. lol
sd card slots not in the same place either
An NFC-chip inside the battery would actually make sense. It has a large surface area inside the phone, which would make the NFC handling easier.
However, the design is completly different. On the non-NFC GS2, the microSD cardslot is on the left side and the battery connectors are on the right side. Some small differences with the SIMcardslot and the external antenna connector too. So it seems its more than just the battery.
What are the specs on this version? Do they use the AT&T US frequencies?
Just a quick question: Have you checked 3G bands on the phone?
I heard that the Korean version is NOT quad-band, and am just wondering if you could check that.
Thanks.
I mentioned this a while ago.
http://forum.xda-developers.com/showthread.php?p=13760704#post13760704
It's my understanding that the phone extends the NFC antenna onto the battery so signals don't get blocked by the battery.
It's tri-band only. Don't know why they'd do that though.
bmstrong said:
What are the specs on this version? Do they use the AT&T US frequencies?
Click to expand...
Click to collapse
I think this version is quad-band GSM and quad-band UMTS. Not sure, I dont have the box with me. Will test this with AT&T in the states when i get back there next month.
kohiiou said:
Just a quick question: Have you checked 3G bands on the phone?
I heard that the Korean version is NOT quad-band, and am just wondering if you could check that.
Thanks.
Click to expand...
Click to collapse
I'm unable to use the 3G since i dont have phone service on this SGS2, im just using it on wifi at the moment.
Sticks02 said:
I mentioned this a while ago.
http://forum.xda-developers.com/showthread.php?p=13760704#post13760704
It's my understanding that the phone extends the NFC antenna onto the battery so signals don't get blocked by the battery.
It's tri-band only. Don't know why they'd do that though.
Click to expand...
Click to collapse
How do you check to see if it's tri-band or quad-band GSM/UMTS?
can you pls dump the stock ROM u have in that SGS2 ? it might be useful... i dont know in what way, but may be yes or may be no...
just curious.... from that pic its quite clear that the battery has the NFC chip built in to the SGS2..... thats amazing...
thats why samsung has maded such a thin plastic backcover... i guess so.... nice thinking & it is an indirect clue i am almost sure....
what do u guys think ???
Was on one of the Korean Samsung Spec pages. Lost the link. Although I don't see why they'd make the international version quad band and the domestic version tri band, makes no sense. There's a number code you can enter to check the phone's settings/hardware. It didn't seem to work for me though.
BTW how did you manage to get the phone? It's my understanding you can't buy it outright here unless you're on a visa. Unless you're on a visa...
@manuvaidya:
They've been dumped already. They were dumped a few days after the phone was released. Seems like it's just not that interesting to devs here.
http://forum.xda-developers.com/showthread.php?t=1068307
manuvaidya said:
can you pls dump the stock ROM u have in that SGS2 ? it might be useful... i dont know in what way, but may be yes or may be no...
just curious.... from that pic its quite clear that the battery has the NFC chip built in to the SGS2..... thats amazing...
thats why samsung has maded such a thin plastic backcover... i guess so.... nice thinking & it is an indirect clue i am almost sure....
what do u guys think ???
Click to expand...
Click to collapse
I hope so, we can just purchase the battery and/or sim if both are needed and we get NFC.
I guess NFC in the future release might mean it comes with a NFC enabled battery.
I found a basic side-by-side comparison of the Korean and Internation models:
hxxp://u23dom.blogspot.com/2011/04/galaxy-s2_29.html
Hit up Google Translate for a .. er .. translation.
Ad-sales said:
This is super interesting! From your pics I see that the phone has 4 connector pins, how many does the battery have? How many does the Indian battery have? I am inclined to believe this is the mystery behind "Optional NFC".
Click to expand...
Click to collapse
The UK release phone also has 4 connectors pins and the UK battery also has 4 connectors.
chalid said:
An NFC-chip inside the battery would actually make sense. It has a large surface area inside the phone, which would make the NFC handling easier.
However, the design is completly different. On the non-NFC GS2, the microSD cardslot is on the left side and the battery connectors are on the right side. Some small differences with the SIMcardslot and the external antenna connector too. So it seems its more than just the battery.
Click to expand...
Click to collapse
I have the same battery that is labeled "Near Field Communication" and no, unfortunately it does not enable NFC on a stock UK phone running KE7.
Also, did anyone notice that the connector pins on the Korean SGSII are on the left side vs ours which is on the right?
Sleepycat3 said:
The UK release phone also has 4 connectors pins and the UK battery also has 4 connectors.
I have the same battery that is labeled "Near Field Communication" and no, unfortunately it does not enable NFC on a stock UK phone running KE7.
Also, did anyone notice that the connector pins on the Korean SGSII are on the left side vs ours which is on the right?
Click to expand...
Click to collapse
I think it's like that because the Korean SGS2 has an antenna on the right side to watch TV-over-the-air.
llBlackenedll said:
It would be interesting to see some side on shots compared to a standard SGS II - I hear the NFC version is somewhat thicker?
Click to expand...
Click to collapse
Extra thickness is probably from the DMB tuner
All korean phones come with DMB tuners.
jealous+++++++++
what is the software version of this device?
Dang, I was thinking of getting a spare battery from Korea.
Do both batteries work with uk version of the phone?
Sent from my GT-I9100 using XDA App
Hey guys, I am not totally sure what I did but may I can get some opinions.
I am on a n900v, rooted, on build 4 (4.3) of JellyBeans. Ive also verified that I am on LTE/CDMA
I was having some issues with the proximity sensor so I followed a detailed tutorial on youtube on unscrewing the back and airdusting the sensor. Im pretty handy with electronics so I was pretty cautious and careful.
After reassembling it I am not having issues with 4G dropping out to 3G and or high ping/lag. The phone on idle will be show LTE 3-4 bars. At times when I try to use it for data purposes, browse the internet, download something, the connection will drop out down to 3G.
Downloads and uploads seem really slow, often at times they dont even complete (dropbox progress bar freezes). Speed test often has high ping, and while testing, I tend to get network communication issues. My speeds are pretty rough as well.
Ive opened it back up, nothing is loose, nothing damaged, antenna pins all seem fine to be making fine connects from the board to the backplate.
It almost feels like I am being throttled, but the dropping down to the 3G and the connectivity issues makes me want to rule out that.
Im just curious if you guys have any ideas on how to handle it.
A couple of things I have considered. 1. Calling in for a replacement SIM card (its still the card I had from GNex launch day, maybe taking it out somehow has it acting up? 2. It is out of warranty, though I do have asurion, though I had considered canceling it. I could report it damaged and file a claim (though I could get stuck with a 4.4.4 device in return).
Any other options I haven't considered would be appreciated it. I thought about reflashing the rom but this seems more likely hardware based than software.
Thanks guys!
No ideas guys?
I swapped SIM cards, its still happening. Not sure what my options are other than swapping out the motherboard, but a warranty replacement is probably cheaper.
jsk23 said:
No ideas guys?
I swapped SIM cards, its still happening. Not sure what my options are other than swapping out the motherboard, but a warranty replacement is probably cheaper.
Click to expand...
Click to collapse
You already covered the thing I thought it was also I fixed my sensor by editing the calibration for it.
What radio are you using?
mirrin said:
You already covered the thing I thought it was also I fixed my sensor by editing the calibration for it.
What radio are you using?
Click to expand...
Click to collapse
Im still on MJ7, which had been fine all this time. I'm going to try moving to a new one, but I still think that maybe this is a hardware thing.
jsk23 said:
Im still on MJ7, which had been fine all this time. I'm going to try moving to a new one, but I still think that maybe this is a hardware thing.
Click to expand...
Click to collapse
Yes it does sound like the 4G antenna is broken or unplugged. But you said you checked that and wires were fine. So NK1 radio only.
jsk23 said:
No ideas guys?
I swapped SIM cards, its still happening. Not sure what my options are other than swapping out the motherboard, but a warranty replacement is probably cheaper.
Click to expand...
Click to collapse
Here's a guide from another thread...
There are several antennas
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Sent from my Note 3 via Tapatalk
donc113 said:
Here's a guide from another thread...
There are several antennas
View attachment 3152797
Sent from my Note 3 via Tapatalk
Click to expand...
Click to collapse
Appreciate it, Ill take a look later on when I have some time. Thing is, I never even took off the motherboard or anything but the backplate. Most of the antennas are just contact points to the backplate if I am not mistaken?
Also, even when on 3G I seem to be getting a 4G signal. See the screenshot. But its like the handshake between 3 and 4G is messed up.
Though that LTE CQI value being n/a could be an issue.
jsk23 said:
Appreciate it, Ill take a look later on when I have some time. Thing is, I never even took off the motherboard or anything but the backplate. Most of the antennas are just contact points to the backplate if I am not mistaken?
Also, even when on 3G I seem to be getting a 4G signal. See the screenshot. But its like the handshake between 3 and 4G is messed up.
Though that LTE CQI value being n/a could be an issue.
Click to expand...
Click to collapse
No...that's normal (cqi being n/a)
The screws around the backplate are what "attach" the antennas. There have been several reported instances of signifigantly better reception after making sure those screws are "snug."
Sent from my Note 3 via Tapatalk
My charge port is busted and I want to replace it but cannot find G900W8 (Canadian model) anywhere.
I read somewhere that I could use the G900T model daughter board.
Can anyone confirm this? Thanks!
you can buy any charge port of any model, it is default from manufacture. ------- Galaxy S5 SM-G900F works aswell like i said.
you can't buy the charger port of Galaxy S5 New Edition because i believe it has different mAh and it has some pieces that does not have on S5 Old edition.
My model is the Canadian version Galaxy S5 - so you're saying I'd be fine no matter what version of the daughter board I buy?
A second question - I've noticed online you can buy just the silver micro-usb port... Would this be an easy fix? Does the port itself pop on and off the motherboard? Or is it hardwired / requiring lots of intricate soldering? If it pops on and off just like the flex cables do onto existing pins, then that seems like a much better solution - but I can't tell without taking the whole thing apart and no one discusses this as an option online - they all talk about replacing the daughter board.
No.....it won't be fine.....this is something I know about....having had experience of this issue on a number of Samsung devices.....
You *do* need to match the board physically.....but not only that, you need to match the REV (revision) number from your existing board to the one you buy....
There will likely be a number of older/newer versions of the board, and in my experience they are NOT interchangeable.....
And as for replacing just the socket, this is something I have considered attempting in the past....but the simple truth is that the connectors are just too small to accurately hand solder....You'd need a very low power soldering iron with a needle point tip and a rock steady hand.
You'd also need a lighted magnifying glass to enable you to actually see what you were doing.
http://i.imgur.com/rVnFwJM.jpg
keithross39 said:
No.....it won't be fine.....this is something I know about....having had experience of this issue on a number of Samsung devices.....
You *do* need to match the board physically.....but not only that, you need to match the REV (revision) number from your existing board to the one you buy....
There will likely be a number of older/newer versions of the board, and in my experience they are NOT interchangeable.....
And as for replacing just the socket, this is something I have considered attempting in the past....but the simple truth is that the connectors are just too small to accurately hand solder....You'd need a very low power soldering iron with a needle point tip and a rock steady hand.
You'd also need a lighted magnifying glass to enable you to actually see what you were doing.
http://i.imgur.com/rVnFwJM.jpg
Click to expand...
Click to collapse
in fact i believe they are default.
only matching the revision number. if you find an recent revision, that's fine. only not buying an old revision.
only what changes is the modem country code.
scott487 said:
My model is the Canadian version Galaxy S5 - so you're saying I'd be fine no matter what version of the daughter board I buy?
A second question - I've noticed online you can buy just the silver micro-usb port... Would this be an easy fix? Does the port itself pop on and off the motherboard? Or is it hardwired / requiring lots of intricate soldering? If it pops on and off just like the flex cables do onto existing pins, then that seems like a much better solution - but I can't tell without taking the whole thing apart and no one discusses this as an option online - they all talk about replacing the daughter board.
Click to expand...
Click to collapse
to change the usb port, you will need an soldering iron; 30w will be enough to do the work.
and experience how to solder.
keithross39 said:
No.....it won't be fine.....this is something I know about....having had experience of this issue on a number of Samsung devices.....
You *do* need to match the board physically.....but not only that, you need to match the REV (revision) number from your existing board to the one you buy....
There will likely be a number of older/newer versions of the board, and in my experience they are NOT interchangeable.....
And as for replacing just the socket, this is something I have considered attempting in the past....but the simple truth is that the connectors are just too small to accurately hand solder....You'd need a very low power soldering iron with a needle point tip and a rock steady hand.
You'd also need a lighted magnifying glass to enable you to actually see what you were doing.
http://i.imgur.com/rVnFwJM.jpg
Click to expand...
Click to collapse
Thanks - But I'm wondering what you think of this posting: http://forums.androidcentral.com/sa...0w8-charging-port-flex-cable-replacement.html
It's saying that Canadians (G900W8) should use the T version. That's what I'm hoping to confirm. Because I cannot find the G900W8 version online anywhere.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
@DBlackFireD There is simply no way of accurately soldering these contacts.....
I have all the practical hand soldering experience you can think of.....it can't be done.....There is a reason that these boards are assembled on automated production lines, and that is that computer controlled robots do not have shaky hands. If you try to hand solder the socket, you WILL end up causing other damage.
@scott487 I understand that the W8 board may be hard to find.....it might well be the case that the board for the T variant is compatible....I had a look at the thread you linked to, and I noticed the lack of feedback as to whether it worked or not...
If it were me, I'd still try to source the W8 board, and keep the T board in mind as a last resort.
With regards to what has been said about the REV versions of replacement boards.....
There may be some truth about newer replacements being reverse compatible with older originals....but doing things the other way around *definitely will not* work.....
And getting the wrong REV version has been known to break functionality on other Samsung phones.......things like data transfer, signal strength etc; so these boards are NOT generic/default....
I still maintain that replacing your existing board with one that has an identical REV number should be considered as a first resort......
http://i.imgur.com/rVnFwJM.jpg