Bricked 6815 please help! - Sable

Hi, I'm new to this forum. I have bricked my 6815 during wm 6.5 rom update. It want turn on. I have tried procedure with removing battery and presing two "-" keys, but without success. I left it for night without battery and card and tried again, but nothing. Battery indicator is working, when I put charger or PC USB port on it. Battery is fully charged. What can I do? Should I throw it like a brick, or you have some genius smart solution, as always?

try here
http://forum.xda-developers.com/forumdisplay.php?f=296
the 6815 is essentially a rebadged Atom

Related

what can i do for my xda 2? please help me.please guys.helpp

i was installing new rom on my device.when it was 12%, the computer got locked and i had to reset.Now,my baby did not reflash again.i tried again but himaupragadeutility gave : communication problem. what can i do now? can anyone help me? so a few people know this device, the others even do not know what pda is. what i can do?????????????????????????????
Try putting your device into bootloader mode and making sure your XDA is plugged into the mains as well. There's also an upgrade program which bypasses country id checks.
Good luck.
I got the same problem with my Qtek 2020i today!!!!!
The device is dead and i can't put it into bootloader mode!
I need your help please
Try taking the battery out for about 1 hour. This will run the backup battery down therefore wiping the ram. Put the battery back in, connect it to the mains and put it into bootloader by pressing power, action and reset for about 3-5 seconds until serial appears on screen. No backlight so look carefully.
I tried to remove the battrey for 1 hour but it's still the same!
any way thanks for trying to help pug.

qtek 9000 doesn't turn on

first i'm sorry for my english i try to explain my problem in best language
i have a qtek 9000 and one hour ago i flashed my phone with Ranju_v76_WM61_19209_19209_1_0_2.exe (sticky topic) and this operation finish correctly.I used wm6 for abouy 5 minutes. suddendly my ppc turn off and doesn't power up but if i press keys for hard reset it power up with press 0 to restore factory or X...
If i press 0 my ppc turn down and doesn't power up.
If i try to connect in my pc windows xp write "Periferica non riconosciuta".
how can i do?
Hi Alex, well, have you tried to enter in bootloader mode and re-flash with your prior rom?
Also, you might want to try a full hard reset to your device first.
Let me know if you need italian directions for this.
battery
Also check if your battery is old or try getting a new one and charge it and boot it up.
Mine was some what of the same problem, until i got a new battery and now it's working.
My XDA with the ranju rom did this over the weekend. Was working fine for weeks then turn it on after 2 days non use and its dead. Could the rom have an issue?
All sorted now via bootloader.

my Qtek 9000 just went dead and wont turn on!!

I upgraded my uni with ranju rom 2months ago and worked perfect.Yesterday after a call the uni froze when i restarted, the uni black out. have tried both hard and soft reset. Nothing happens in soft reset, but hard gives U " Press 0 to restore to factory default and X to exit". but if i press 0, the uni goes off again.,
Battery? Can you enter a bootloader and re-flash the ROM?
I can't get pass "Press 0 to restore to factory default -Press X to exit" screen
i also have same problem with you. and i have connect my device to PC usb cable, then PC detect my universal but cant recognize it as pocket pc.
please anyone help us.....
hello
hi all, and thanks in advance for reading this thread.
my cousin gave me his qtek 9000 saying that it was dead. being a dumbass, me decided to try and give it back life. as mentioned before, me a dumbass. After seaching the web for hours, i would normally be now saying, i give up. but no.
so , please. help.
the only thing i can tell u is that when i plug it in the pc, a red light starts bleeping. Won't turn on, soft and hard reset do not seem to make any effect, nor the power+light button.
again, please, help.
Had exactly the same...my qtek 9000 was just lying in the closet for a long time and would not boot anymore...
When I used it last time al was fine. I figured a dead battery so bought a new one...
It would give me the red LED while charging, would not be recognised on the computer etc.
Did a hard reset and then got it into the bootloader...
Had to run my laptop on XP as under Win7 it would fail to flash or do anything, but under XP it flashed properly.
After flash installed my back-up and all seems to be running fine now!
May be it helps anybody...

Fully Dead Elf after flashing ONYX

I flashed my htc elf (t-mobile touch) with onyx ultimate, just over halway it froze, then my whole pc froze and crashed, the phone turned off and i havent been able to get it on since, no lights, no screen, nothing
PLEASE HELP
I have tried:
power button
soft reset
hard reset
bootloader mode
plugging it into my pc and my mac to charge it but still no power
tried plugging it into my pc without the battery to see if the orange light comes on
Any Ideas??
I'm not exactly an expert but I'd have thought attempting to flashing a ROM shouldn't break its power supply. It doesn't add up. You mention the orange light, but does it actually come on or not?
I'll assume you flashed a USPL or you probably wouldn't be getting past 3% in the first place lol.
strange one
yea, it was all ready to be flashed, it was previously on a geniric htc rom that i put on it.
there is no orange light at all, no nothing, i cant seam to work it out, i mate has the same phone and im gonna try his charger and battery when i see him tomorrow but i still cant see how flashing it would affect the power, unless the device is blank now and it doesnt even know what the buttons do e.g the power button is not assigned to do anything.
try with another fully charged battery... and ELF/ELFin Golcard method, with a suitable flash file (like a Original one)
Just my 2 cents...
Try put the battery with the camera button pressed..
i have had the same problem
pres start button and fotos together
will appear 4 colors and ipl ..... and spl ........
if its appear: ipl 2....... and spl 1.11.000 you must upgrade your spl
read : http://forum.xda-developers.com/showthread.php?p=3038443&posted=1#post3038443

elfin completely dead

Hi i think my elfin is completely dead.
it was currently running the latest onyx.(although it doesn't appear to be the problem) at the moment it is plugged into the charger and doesn't show any sign of charging. any ideas would be awesome.
edit: i think i need a new battery cause its working now
could you enter in bootloader?
Hello!
I have the same problem with a friends elf. I can't get into bootloader mode, do a hard or soft reset and the little orange light (charging light) doesn't show up when i connect a power supply.
Is there any way of getting it to work again? I think that even for the Goldcard method at least the bootloader mode is required, right?
Thanks, Vi

Categories

Resources