Related
Guys,
I ve just downloaded this http://rapidshare.com/files/21256078..._DUT_11500.rar romversion in the understanding that it was for the HTC 9000 PDA. There was a file called MaUpgradeUt_noID.exe which I let 'upgrade' my 9000. However, I think something very VERY big went wrong! A reset by pushing the 2 buttons and reset button on the back gives me the option 0 to reset but all I can see after that is a black screen which says USB at the top and at the bottom v1.00
What happened and is this the end of my PDA? Sync won t work anymore now since my PDA can t be detected by windows because I can t get in the PDA!!!
Is there something I can do??!!!
PLEASE HELP ME OUT!!!!
Edit/Delete Message
sounds like you're just in bootloader mode
I think you are in what's called bootloader mode. Read the wiki to check - the screen you are describing sounds normal to me you plug you device into the comp via usb (with sync over usb disabled in active sync) then install a new rom.
You really shouldn't have tried to flash your rom without reading some instructions first but I think that your device should be fine.
If you have already upgraded your rom just do a hard reset and select the option to reset.
Will this thread help?
http://forum.xda-developers.com/showthread.php?t=310056
I'm sorry, this is the thread I ment to link:
http://forum.xda-developers.com/showthread.php?t=310054
strangely enough I found out that I DID use a good version picked from this http://forum.xda-developers.com/showthread.php?t=298020 post. In this thread mwang gives a link to here http://buzzdev.net/index.php?option=com_phorum&Itemid=125&phorum_query=read,40,30486,30486#msg-30486 where I picked the dutch version. I than double clicked the MaUpgradeUt_noID.exe file and the software for upgrading started. When he was at 100% he said the the ROM update was completed and that I had to do a reset. So, I than pushed the three buttons (2x the - button and the reset button at the back of the 9000) but all I than see is the bootloader menu with USB and V1.00...........
Sorry for putting it in three sub forum, my fault, but the device is from my work so I don t want it to be screwed up!!!
sanderh said:
Sorry for putting it in three sub forum, my fault, but the device is from my work so I don t want it to be screwed up!!!
Click to expand...
Click to collapse
Rather late now, but if it's owned by your company for work, should you really be di**ing with it?
Solution to probl: Stuck in Bootloader
The one way of fixing your problems....you're officialy stuck in bootloader,
Here's the way to fix it:
1. Stop Activesync USB connection on your machine under connection settings.
2. Uni : Reboot Bootloader then Connect USB ( If your phone isn't in bootloader already..)
3. PC : Run mtty1.42.exe ( Download from XDA's ftp site or search the forums, I'm sure you'll find it.)
4. Choose USB in "Port" (Reconnect if can't find/reconglize USB and try remove sim and sd card)
5.1 Press Enter
5.2 USB> (This will show up)
6. Type: Set 14 0
7. Press Enter
8. Run your rom update again and it should flash this time.
did it start??
did it start?? ?
Hi. first post.
Have an o2 exec. Different brand same deice and none of the other methods worked but finally got it working. Using mtty1.42.exe it would not see usb connection and therefore could not go down that route.
I booted into the bootloader mode that says serial at the top and v1.00 at the bottom.
Connected to the pc and cant remember if i stopped wcescomm.exe or not but you can try both ways.
Then started Midget_1990_v1_0_PU10_WWE.exe rom and followed the instructions and voila.
Hope this helps someone.
"Using mtty1.42.exe it would not see usb connection"
You need to disable the usb connection of active sync under connection settings and then only mtty will pick up a usb connection..
im getting a touch hd from taiwan. and i just read that it comes in chinese only
is there any rom to make it english? or change the os language to english
and what is the country code for it?
if there isnt. will i have to use hard spl?
and i read the instructions for it but im kinda lost
please help
Thanks in advance
Allmost all ROMS are in english. There are ways you can flash them without using hard spl.
EpiphanyNL said:
Allmost all ROMS are in english. There are ways you can flash them without using hard spl.
Click to expand...
Click to collapse
i checked "http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Ship_exe"
and im not sure which one to download
im not really sure which is the country code for taiwan. any ideas?
there are ways to flash without using hard spl?
can you please tell me how?
Read this for flashing without Hard spl: http://forum.xda-developers.com/showthread.php?t=462347
Why would you want the country code for taiwan? You dont need it when flashing another ROM.
EpiphanyNL said:
Read this for flashing without Hard spl: http://forum.xda-developers.com/showthread.php?t=462347
Why would you want the country code for taiwan? You dont need it when flashing another ROM.
Click to expand...
Click to collapse
i read that i need to know so i know which rom to download?
i think. i read it here " http://wiki.xda-developers.com/index.php?pagename=HTC_Blackstone_Flash1"
so im going crazy looking for a rom that i could use.
do you know where i can download one so i can make my language WWE instead of chinese.?
I'm using this ROM atm: http://www.laurentius26.net/
You can find enough ROMS in this thread btw, read carefully and you will find them
EpiphanyNL said:
I'm using this ROM atm: http://www.laurentius26.net/
You can find enough ROMS in this thread btw, read carefully and you will find them
Click to expand...
Click to collapse
thanks but one question?
which is the easiest way to flash a rom?
using Hard SPL, Soft SPL, or USPL?
im really lost on that..
and which one should i use?
Cant really help you there, I use hard SPL, but I guess it's just what your preference is in that.
EpiphanyNL said:
Cant really help you there, I use hard SPL, but I guess it's just what your preference is in that.
Click to expand...
Click to collapse
oh really?
hardspl is only for blac100 right?
but i read that now they have like blac120?
and im not sure which one im gunna be getting in the box.
oh. when i change the os language. do i have to download one with the same country code?
i read in another place that if you dont have the same. then. it wont work?
or with hardspl and uspl i dont need to have the same country code
anyone? im kind of a newbie
i need help please
im going to be getting my touch hd soon in chinese
and i need to change it to english
help
thank you!
kevin6192 said:
anyone? im kind of a newbie
i need help please
im going to be getting my touch hd soon in chinese
and i need to change it to english
help
thank you!
Click to expand...
Click to collapse
Its not very hard to be honest
You must flash HardSPL first to be able to flash any rom and hardspl will work for blac100 and blac120
More info and instruction about HardSPL
Tips about flashing the rom
Use fully charged device
* Switch off your device by holding the Power button untill a menu pops up
* Go to bootloader by holding Volume down + Power button at the same time
* Connect your device to your PC
* Start BlackStoneCustomRUU.exe and follow the onscreen instruction's
There are countless ROM's out there and everyone has different tastes so there is no point asking any questions on which is better etc etc etc.
I am curretnly using Duttys 2.3 rom and would recommned it or Laurentius26 V9.0
Hope this helps!
Laurentius26
I got mine from hong Kong when I was there in Feb, it was in chinese too. then I went to the wiki page, downloaded the Hard SPL, once that was done I just picked any ROM on the wiki page, I chose Dutty 1.7 at the time. copied the NBH file to the root of the SD card, made sure the name of the NBH file was BLACIMG.nbh and then used restarted the device with the key presses mentioned in the wiki and flashed it to english. MAKE sure you have at least 50% charge before you start.
the WWE versions are the english roms. I believe its mentioned in the wiki too.
Since then I've maybe flashed like 10 or more times and tried different roms. it doesn't matter which rom you pick. its a matter of personal preference. just take the time to read the wiki in detail and you'll be fine.
if you are getting a retail touch HD it will come with an 8GB SDHC micro SD and the usual accessories.
as of now I'm on dutty's 2.3
alvinswim said:
I got mine from hong Kong when I was there in Feb, it was in chinese too. then I went to the wiki page, downloaded the Hard SPL, once that was done I just picked any ROM on the wiki page, I chose Dutty 1.7 at the time. copied the NBH file to the root of the SD card, made sure the name of the NBH file was BLACIMG.nbh and then used restarted the device with the key presses mentioned in the wiki and flashed it to english. MAKE sure you have at least 50% charge before you start.
the WWE versions are the english roms. I believe its mentioned in the wiki too.
Since then I've maybe flashed like 10 or more times and tried different roms. it doesn't matter which rom you pick. its a matter of personal preference. just take the time to read the wiki in detail and you'll be fine.
if you are getting a retail touch HD it will come with an 8GB SDHC micro SD and the usual accessories.
as of now I'm on dutty's 2.3
Click to expand...
Click to collapse
Fallen Spartan said:
Its not very hard to be honest
You must flash HardSPL first to be able to flash any rom and hardspl will work for blac100 and blac120
More info and instruction about HardSPL
Tips about flashing the rom
Use fully charged device
* Switch off your device by holding the Power button untill a menu pops up
* Go to bootloader by holding Volume down + Power button at the same time
* Connect your device to your PC
* Start BlackStoneCustomRUU.exe and follow the onscreen instruction's
There are countless ROM's out there and everyone has different tastes so there is no point asking any questions on which is better etc etc etc.
I am curretnly using Duttys 2.3 rom and would recommned it or Laurentius26 V9.0
Hope this helps!
Laurentius26
Click to expand...
Click to collapse
im sorta confused on how to install Hardspl
i read the instructions..but im lost
do you think you guys can help me out?
like explain in an easier way?
sorry for the inconvenience
can i also use USPL?
kevin6192 said:
im sorta confused on how to install Hardspl
i read the instructions..but im lost
do you think you guys can help me out?
like explain in an easier way?
sorry for the inconvenience
can i also use USPL?
Click to expand...
Click to collapse
Instructions
Download Hard-SPL package from attachment, extract to an empty folder.
Unsigned_HardSPL_for_Blackstone_OliNex.zip
You must Have Phone Sync'd with PC in Windows Mobile!!!
Run HardSPLWrapper_Blackstone.exe on PC,
make sure it's launched from a local drive (not through network drive, etc.).
if you are on vista, launching as Administrator is recommended,
Follow steps in the RUU
check device for prompts after PC shows loading bar
press Yes on phone if asked.
Some notes: When RUU says it will hard reset, do not worry, it is not going to do that. also when it says the flash will take 10 minutes, ignore that, it will only take a minute or so.
Device should go to a tricolour screen now that says 1.07.OliNex, the SSPL version, which is temporary.
In a bit unusual way, it will take a few seconds for the RUU to detect the device, but do not worry, as soon as the "USB" text on the tricolour screen shows up, RUU will see device.
SPL flashes, device automatically reboots, job done.
To confirm you got it installed,
go into bootloader mode (tricolour screen!) (Switch off your device by holding the Power button untill a menu pops up > Go to bootloader by holding Volume down + Power button at the same time)
verify the screen shows 1.14.OliNex, which is the Hard-SPL version.
I just got my Touch HD over the weekend and I used USPL so that I don't void the warranty:
http://forum.xda-developers.com/showthread.php?t=462347
However, you need to have XP. Tried it on Vista but not successful. Luckily I had an old XP laptop stuffed away somewhere
ionrage said:
I just got my Touch HD over the weekend and I used USPL so that I don't void the warranty:
http://forum.xda-developers.com/showthread.php?t=462347
However, you need to have XP. Tried it on Vista but not successful. Luckily I had an old XP laptop stuffed away somewhere
Click to expand...
Click to collapse
oh really?
when it says
"Execute blac_uspl.exe;" do i just find the file ont he computer and double click it? or do i have to like install it using the phone?
and " If everything goes well, your device will restart and SPL version label should read "1.14.USPL" indicating that USPL was loaded successfully."
once that is done then... am i done?
this next part is when i want to flash a rom right?
("You can then start RUU update to flash RUU_signed.nbh. Once RUU update is completed, device will restart using regular flashed SPL.
If you want to flash from SD card instead, make sure your SD card is not inserted when you enter the bootloader originally.
SPL will try to install it and would fail if blacimg.nbh is not signed by HTC. Insert the card after "USB" label comes up in SPL but before running USPL.
You can run "blac_uspl.exe ?" to get command line parameter help. Only 1 parameter is accepted and that is the name of an SPL file you want to load. You can load an MFG SPL or HSPL. USPL automatically takes care of allowing unsigned/cooked ROM flashing with any SPL you use.")
man. i dont have XP
thers no way on vista?
thanks for the inconvenience.
Fallen Spartan said:
Instructions
Download Hard-SPL package from attachment, extract to an empty folder.
Unsigned_HardSPL_for_Blackstone_OliNex.zip
You must Have Phone Sync'd with PC in Windows Mobile!!!
Run HardSPLWrapper_Blackstone.exe on PC,
make sure it's launched from a local drive (not through network drive, etc.).
if you are on vista, launching as Administrator is recommended,
Follow steps in the RUU
check device for prompts after PC shows loading bar
press Yes on phone if asked.
Some notes: When RUU says it will hard reset, do not worry, it is not going to do that. also when it says the flash will take 10 minutes, ignore that, it will only take a minute or so.
Device should go to a tricolour screen now that says 1.07.OliNex, the SSPL version, which is temporary.
In a bit unusual way, it will take a few seconds for the RUU to detect the device, but do not worry, as soon as the "USB" text on the tricolour screen shows up, RUU will see device.
SPL flashes, device automatically reboots, job done.
To confirm you got it installed,
go into bootloader mode (tricolour screen!) (Switch off your device by holding the Power button untill a menu pops up > Go to bootloader by holding Volume down + Power button at the same time)
verify the screen shows 1.14.OliNex, which is the Hard-SPL version.
Click to expand...
Click to collapse
do i have to have the phone connected to the computer before i run HardSPLWrapper_Blackstone.exe?
what does it mean when it says make sure it is launched from a local drive?
or a network drive?
where are the steps for the RUU?
sorry for all the questions!
kevin6192 said:
do i have to have the phone connected to the computer before i run HardSPLWrapper_Blackstone.exe?
what does it mean when it says make sure it is launched from a local drive?
or a network drive?
where are the steps for the RUU?
sorry for all the questions!
Click to expand...
Click to collapse
Yes, you need phone sync'd to pc using your usb cable before running HardSPLWrapper_Blackstone.exe?
What I mean by local drive is your C:/ drive or local disk and not by using other drives you may have i.e. G:/, H:/, J:/ etc
When you run HardSPLWrapper_Blackstone.exe a screen will appear on your pc and it will have these steps on it for you to follow. i.e. just follow these steps
Fallen Spartan said:
Yes, you need phone sync'd to pc using your usb cable before running HardSPLWrapper_Blackstone.exe?
What I mean by local drive is your C:/ drive or local disk and not by using other drives you may have i.e. G:/, H:/, J:/ etc
When you run HardSPLWrapper_Blackstone.exe a screen will appear on your pc and it will have these steps on it for you to follow. i.e. just follow these steps
Click to expand...
Click to collapse
okay so i have downloaded HardSPLWrapper_Blackstone.exe.
it says extract it so that means i cannot open it from the zip?
is it okay if it is in a folder in the C:/ drive when i launch it?
so first off. i connect the phone to the pc.
( do i put it in bootloader mode?)
what will show on the phone when i connect it?
and when i connect it. i just plug the usb in the phone and the computer and thats it?
then i launch HardSPLWrapper_Blackstone.exe
follow the steps..
then im done?
kevin6192 said:
okay so i have downloaded HardSPLWrapper_Blackstone.exe.
it says extract it so that means i cannot open it from the zip?
is it okay if it is in a folder in the C:/ drive when i launch it?
so first off. i connect the phone to the pc.
( do i put it in bootloader mode?)
what will show on the phone when i connect it?
and when i connect it. i just plug the usb in the phone and the computer and thats it?
then i launch HardSPLWrapper_Blackstone.exe
follow the steps..
then im done?
Click to expand...
Click to collapse
Yes you need to extract it from zip as it will not run from within zip folder
Personally I ran it just from the desktop, i.e. I put HardSPLWrapper_Blackstone.exe on my desktop
when you have your phone connected and in bootloader mode at the bottom on the screen it should say 'usb'.
then launch HardSPLWrapper_Blackstone.exe, follow steps, then your done.
As I said put phone back into bootloader mode afterwards and verify the screen shows 1.14.OliNex, which is the Hard-SPL version.
Long story short my phone worked fine for months. Went to a 1.56 Rom active sync stopped working. I have already tried everything associated with AS problem, everything. Went to get it repaired at HTC America in Houston, TX there gay and dont support T8285. I have tried flashing via memory card but I seem to be retarded doing it that way. Engineer said mini usb slot works fine, cooked rom may have corrupted AS. Customer service would not let him fix my phone because it was an "aussie version". I just want the phone to sync is that too much to ask? Anyway $100 bucks to anyone that can make it work paid via paypal immediately.
moved out of development
Personally I think your mad offering $100. I'm sure most people would have hepled you for free, including myself. I'm not after your money but offer my assistance.
Have you tried doing a hard reset? uninstalling activesync & reinstalling it?
Flashing different rom. If you can't flash through SD Card, have you tried flashing again via usb. You don't need phone sync'd
Put your phone into bootloader and then connect to pc via usb. At bottom of screen the text should change from 'serial' to 'usb'. Now flash phone by running rom (cooked or stock etc) you downloaded. Put .nbh and ruu file into same folder and then open ruu file and follow instructions.
I severely doubt cooked rom affected activesync.
EDIT
As bonesy said below, you'll need either USPL or HSPL to flash 1.56+ based rom.
Full tutorial or dummies guide to flashing 1.56+ based roms can be found in cRaCKwHoRe's guide. See my signature
Turn off your phone, Take out your memory card, Plug the miniUSB in then power on (Hold volume down press power holding volume down still) This will bring up a coloured screen. Run the ROM Wrapper package exe (BlackstoneRUUWrapper) This SHOULD now install the right ROM.
Please make sure you are using a 1.56 rom with the HSPL or i think it has problems with GFX.
When windows loads go to start>settings>connections>USBtoPC
this is on 6.5 rom not sure about 6.1 :/
Untick Enable faster data synchronizaion, I had to do all this on works computer to update a ROM god knows why but this was my fix.
ROM Should load as should activesync now.
Please let me know if this helps
Tried to post in ure original threads but mods were moving to trash each time BAH!
Thanks to both of you guys for your suggestions. I thought I was not a noob when it came to flashing roms but once I could not do it via usb I was a whole different story. Yeah I am offering the $100 just to get people to help. I know you get slammed if you ask a question so I figured I would make it worth someone's time. I am going right now to pick it up from the repair center so I will try during my lunch in about an hour.
Fallen Spartan said:
Personally I think your mad offering $100. I'm sure most people would have hepled you for free, including myself. I'm not after your money but offer my assistance.
Have you tried doing a hard reset? uninstalling activesync & reinstalling it?
Flashing different rom. If you can't flash through SD Card, have you tried flashing again via usb. You don't need phone sync'd
Put your phone into bootloader and then connect to pc via usb. At bottom of screen the text should change from 'serial' to 'usb'. Now flash phone by running rom (cooked or stock etc) you downloaded. Put .nbh and ruu file into same folder and then open ruu file and follow instructions.
I severely doubt cooked rom affected activesync.
Click to expand...
Click to collapse
I tried uninstalling and reinstalling active sync. Different cables, different computers, xp and vista, everything, checked usb enhanced, etc ,etc.
bonesy said:
Turn off your phone, Take out your memory card, Plug the miniUSB in then power on (Hold volume down press power holding volume down still) This will bring up a coloured screen. Run the ROM Wrapper package exe (BlackstoneRUUWrapper) This SHOULD now install the right ROM.
Please make sure you are using a 1.56 rom with the HSPL or i think it has problems with GFX.
When windows loads go to start>settings>connections>USBtoPC
this is on 6.5 rom not sure about 6.1 :/
Untick Enable faster data synchronizaion, I had to do all this on works computer to update a ROM god knows why but this was my fix.
ROM Should load as should activesync now.
Please let me know if this helps
Tried to post in ure original threads but mods were moving to trash each time BAH!
Click to expand...
Click to collapse
Thanks for breaking it down barney style for me. I will try this very soon. If it works my friend you got $100 smackers.
no worries, Glad to help (if it does lol)
bonesy said:
Turn off your phone, Take out your memory card, Plug the miniUSB in then power on (Hold volume down press power holding volume down still) This will bring up a coloured screen. Run the ROM Wrapper package exe (BlackstoneRUUWrapper) This SHOULD now install the right ROM.
Please make sure you are using a 1.56 rom with the HSPL or i think it has problems with GFX.
When windows loads go to start>settings>connections>USBtoPC
this is on 6.5 rom not sure about 6.1 :/
Untick Enable faster data synchronizaion, I had to do all this on works computer to update a ROM god knows why but this was my fix.
ROM Should load as should activesync now.
Please let me know if this helps
Tried to post in ure original threads but mods were moving to trash each time BAH!
Click to expand...
Click to collapse
So I got my phone and this is what it says.
BLAC120 32M
SPL-1.56.01Olinex
MicroP-Blackstone (LED) v6
and it's just red green blue and white no word on the bottom. Ran BlackstoneRUUWrapper with the nbh file that I wanted and it gave me a connection error. Now it says Seiral in the white.
Fallen Spartan said:
Personally I think your mad offering $100. I'm sure most people would have hepled you for free, including myself. I'm not after your money but offer my assistance.
Have you tried doing a hard reset? uninstalling activesync & reinstalling it?
Flashing different rom. If you can't flash through SD Card, have you tried flashing again via usb. You don't need phone sync'd
Put your phone into bootloader and then connect to pc via usb. At bottom of screen the text should change from 'serial' to 'usb'. Now flash phone by running rom (cooked or stock etc) you downloaded. Put .nbh and ruu file into same folder and then open ruu file and follow instructions.
I severely doubt cooked rom affected activesync.
EDIT
As bonesy said below, you'll need either USPL or HSPL to flash 1.56+ based rom.
Full tutorial or dummies guide to flashing 1.56+ based roms can be found in cRaCKwHoRe's guide. See my signature
Click to expand...
Click to collapse
Well I get it into bootloader no problem but then plug in the usb cable and nada, it says serial. So then I tried starting bootloader mode with the cabe and still nada, it does not even say serial. If I unplug it then it says serial. I have tried both ways to run the RUU Wrapper and I keep getting the usb conncetion error
serial?
Hi, please can you post a screen shot of where it says serial at boot screen?
stoolzo said:
Hi, please can you post a screen shot of where it says serial at boot screen?
Click to expand...
Click to collapse
I cant because I cant use my software that would do that since it wont sync to my computer.
snap shot
just take a snap shot with a webcam or digital camera if you have one.
stoolzo said:
just take a snap shot with a webcam or digital camera if you have one.
Click to expand...
Click to collapse
let me see if this comes thru ok.
turcomora said:
let me see if this comes thru ok.
Click to expand...
Click to collapse
Here yo go. This picture is with me having the device plugged in it charging fine. Then entering bootloader mode. If I unplug then it will say serial. If I dont plug in before then enter bootloader it will say serial still.
thanks
ok, that looks pretty normal,so to recap you fully powerdown the phone by taking the battery out, put the cable into both the phone and pc and the turn on holding volume down and it just sits there?, what happens when you press volume up at this point?
stoolzo said:
ok, that looks pretty normal,so to recap you fully powerdown the phone by taking the battery out, put the cable into both the phone and pc and the turn on holding volume down and it just sits there?, what happens when you press volume up at this point?
Click to expand...
Click to collapse
Only thing I was not doing was taking out the battery. Just tried that and still same screen. Nothing happens when I press the volume up button just stays there.
pc
do you have another pc to try this on to rule out an actual active sync problem?
stoolzo said:
do you have another pc to try this on to rule out an actual active sync problem?
Click to expand...
Click to collapse
Yeah I have been trying on my latop, home pc, and work pc and nothing same result. I have tried different usb cables, os, reinstalling, everything. Only thing I have not tried is flashing via sd card yet.
brick
its sounds like you have a corrupt spl, it is definately worth trying the sd card as it may allow you to activesync but it may then fallover when it reboots and goes into boot mode. This i where user viperbjk (see android dev thread) may be able to help as he has successfully managed to unbrick a phone.
I had this same problem but powering down and simply triggering the and spl reflash resolved it. your problem sounds different though.
Hello. This is my first time when I'm upgrading my Blackstone ROM and I get some problems so I cannot upgrade it
I think the problem is with active sync, but just I think like that maybe I'm wrong. First of all my active sync cannot connect the phone if the box is ticked for "Enable Faster Data Sync" I tried to reinstall active sync, version still not working. When the box is not ticked the active sync connect the phone but when I go into Rom upgrade setup and try to upgrade the ROM the phone restarts ant freezes in 0% of upgrade, then I get a windows with Connection Error. I take the battery out ant turn on my phone normally again.
Do you know how to solve this error? Or can you tell me other ways which I can upgrade my ROM? I know that its possible to upgrade via memory card but I don't know how. Thank you!
dnlaod any ROM, extract the file then u'll see a file named "ruu_signed.nbh"
change its name to "BLACIMG.nbh" then put it into ur storage card.
Go to bootloader mode then press power button n wait.. after ROM upgrade jus Hard reset it..
PS : read the WIKI
Sw1pe said:
Hello. This is my first time when I'm upgrading my Blackstone ROM and I get some problems so I cannot upgrade it
I think the problem is with active sync, but just I think like that maybe I'm wrong. First of all my active sync cannot connect the phone if the box is ticked for "Enable Faster Data Sync" I tried to reinstall active sync, version still not working. When the box is not ticked the active sync connect the phone but when I go into Rom upgrade setup and try to upgrade the ROM the phone restarts ant freezes in 0% of upgrade, then I get a windows with Connection Error. I take the battery out ant turn on my phone normally again.
Do you know how to solve this error? Or can you tell me other ways which I can upgrade my ROM? I know that its possible to upgrade via memory card but I don't know how. Thank you!
Click to expand...
Click to collapse
have u updated ur SPL... or r u using USPL..
IF u have then just boot into the boot loader and connect to USB and flash..
ignore the RUU saying that u need to be connected in active sync...
Moved out of development
cvchetan said:
have u updated ur SPL... or r u using USPL..
IF u have then just boot into the boot loader and connect to USB and flash..
ignore the RUU saying that u need to be connected in active sync...
Click to expand...
Click to collapse
I don't even know what SPL or USPL is. I told you this is my first time so i don't know those sort words. Can you explain properly what is those spl or uspl? thanks
bjy8138 said:
dnlaod any ROM, extract the file then u'll see a file named "ruu_signed.nbh"
change its name to "BLACIMG.nbh" then put it into ur storage card.
Go to bootloader mode then press power button n wait.. after ROM upgrade jus Hard reset it..
PS : read the WIKI
Click to expand...
Click to collapse
Thanks! I'm going to try your way today when I'm gonna come back to my home.
Sw1pe said:
I don't even know what SPL or USPL is. I told you this is my first time so i don't know those sort words. Can you explain properly what is those spl or uspl? thanks
Click to expand...
Click to collapse
This is all explained in the wiki. Before you do anything, best advice I can give you is to read up on SPL, USPL first!!!
Also, if you follow cRaCKwHoRe's guide (see my signature) you cannot go wrong.
Fallen Spartan said:
This is all explained in the wiki. Before you do anything, best advice I can give you is to read up on SPL, USPL first!!!
Also, if you follow cRaCKwHoRe's guide (see my signature) you cannot go wrong.
Click to expand...
Click to collapse
Ok. I will read it later. Thanks!
I'm still having a problem I have have read a wiki and I follow Dummies guide steps but I'm still having a same problem ( Stuck at 0% )
HSPL1 - Downloads
* (HSPL1a) HSPLWrapper_Blackstone_156OliNex.zip
* (HSPL1b) A 1.56+ based rom- Dutty's XT 3.7 linked here
* (HSPL1c) BlackstoneRUUWrapper.zip
* (HSPL1d) Extract each item to its own folder
HSPL2 - Flash new SPL (1.56.OliNex)
* (HSPL2a) Place your phone into its bootloader.
* (HSPL2b) Run HSPLWrapper_Blackstone_156OliNex.exe from the download in step (HSPL1a) and follow it as normal.
I follow these steps but at the last one my phones just freezes at 0% of update, so I can update to 1.56.OliNex SPL
Is me here doing something wrong or is it something wrong with my phone?
Does any one know whats wrong?
never mind. fixed by my self
Sw1pe said:
never mind. fixed by my self
Click to expand...
Click to collapse
how?? i have same problems..
hello am kinda new to all this, i'm trying to install HSPL 3 so i can flash my hd2 with a rom.
I have it Synced with My Computer. I have t-mobile usaHTC HD2. I open up HSPL3 thing. Press next. And its says its trying to connect via USB. stays stuck on that, then gives me an error message?
what am i doing wrong?
I HAVE 2.10.000 on my phone i just bought it. CAN I STILL flash my phone to get a custom rom????
anybody please, 2.10 i hear there is nothing out yet for 2.10 ?
for hspl... (yes it supports 2.10.0000, , dont forget that much of what you are reading was written before hspl3 was released)
1 - dont use a front mounted usb port, use one around back of the pc, directly connected to teh motherboard, not through a hub or case mounted ports.
2 - be sure and right click hspl.exe and choose 'run as administrator
3 - boot into bootloader yourself (start with phone off, press and hold and keep holding vol down, tap and release power, , when get to coloured screen, release vol down, , thats bootloader, ,) connect to usb, when the word 'serial' becomes 'usb' run hspl (as administrator)
keep trying usb ports.
if you are trying to use a virtual box, for example on a mac, , , dont.
oh, and be sure to extract hspl.exe, dont run it from within the .zip file.
thanks sam i got it, i love you.. now just gotta flash to get the rom
samsamuel said:
for hspl... (yes it supports 2.10.0000, , dont forget that much of what you are reading was written before hspl3 was released)
1 - dont use a front mounted usb port, use one around back of the pc, directly connected to teh motherboard, not through a hub or case mounted ports.
2 - be sure and right click hspl.exe and choose 'run as administrator
3 - boot into bootloader yourself (start with phone off, press and hold and keep holding vol down, tap and release power, , when get to coloured screen, release vol down, , thats bootloader, ,) connect to usb, when the word 'serial' becomes 'usb' run hspl (as administrator)
keep trying usb ports.
if you are trying to use a virtual box, for example on a mac, , , dont.
oh, and be sure to extract hspl.exe, dont run it from within the .zip file.
Click to expand...
Click to collapse
sam hows it going? how do i install cookie tab? you can't flash it?
Cookies tab is a cab file which can be found in my sticky. And directions on how to install the cab can also be found in my sticky.
Sent from my HTC Desire using XDA App
ddgarcia05 said:
Cookies tab is a cab file which can be found in my sticky. And directions on how to install the cab can also be found in my sticky.
Sent from my HTC Desire using XDA App
Click to expand...
Click to collapse
i still don't understand? help please
i dont know what to do with the cab? i'm so confused? mm? sam? anyone?
cookies is a program, not a rom, so no, you don't flash it.
copy cookies.cab to your phone, browse to it in your phones file manager, click it to run it.
samsamuel said:
cookies is a program, not a rom, so no, you don't flash it.
copy cookies.cab to your phone, browse to it in your phones file manager, click it to run it.
Click to expand...
Click to collapse
i added it but i cant seem to see it on file manager? mm is their a specific place?
samsamuel said:
cookies is a program, not a rom, so no, you don't flash it.
copy cookies.cab to your phone, browse to it in your phones file manager, click it to run it.
Click to expand...
Click to collapse
got it thanks.
flashing HTC HD2 from TMOUS
Hey,
I'm new to this flashing as well...
I have a Tmobile US HTC HD2...
I installed the HSPL3 after getting the Windows Mobile Device Center...
It was installed successfully, but after that whenever I connect my HTC to my PC, I can hear the ding but my PC is not recognizing my device and there is no connected icon on the HTC as well.
Any help please...
sureshkgopalan said:
Hey,
I'm new to this flashing as well...
I have a Tmobile US HTC HD2...
I installed the HSPL3 after getting the Windows Mobile Device Center...
It was installed successfully, but after that whenever I connect my HTC to my PC, I can hear the ding but my PC is not recognizing my device and there is no connected icon on the HTC as well.
Any help please...
Click to expand...
Click to collapse
it may be connecting in disk mode.
settings menu all settings connection usb to pc.
make sure active sync is selected, and that faster data is NOT selected,.
I am having the same problem, i have tried the steps you gave but to no avail. i have tried every USB slot and tried a different cable. if i try and do it thru bootloader it does not change from serial to usb at all. any ideas? i have flashed roms before but lost my phone and my replacemnt is still running stock rom. ps i cannot even install the official HTC rom update to my phone. any help would be massivly aoppreciated as i am trying to get android on there for experimentation. Regards
thanks for the help!
Same problem..
leezx6r said:
I am having the same problem, i have tried the steps you gave but to no avail. i have tried every USB slot and tried a different cable. if i try and do it thru bootloader it does not change from serial to usb at all. any ideas? i have flashed roms before but lost my phone and my replacemnt is still running stock rom. ps i cannot even install the official HTC rom update to my phone. any help would be massivly aoppreciated as i am trying to get android on there for experimentation. Regards
Click to expand...
Click to collapse
Same here. I'm stuck i just want to update it to froyo 2.2. But i'm missin' this crucial step. Anyone fixed this issue yet?