Related
Hi all. I looked at several wi-fi posts on here, but couldn't find anything related to my problem.
I'm beginning to suspect that it's because of something stupid I'm doing, cos it really should be working...
Anyhoo ...I have a wireless router at home, and it's serving 3 PCs with DHCP IP addresses, and an internet connection. I have no issues with it.
What I'm trying to do now is get my shiny new XDAIIi to connect, so that I can have the damn thing on the internet. So far, no luck.
Now, I have got the XDA to detect my SSID. It detects all the settings, and tells me it's connected. I even have a signal strength bar on it which reads about 50%.
However, when I set it to pick up a DHCP address it stubbornly refuses, remaining with a "I can't see a DHCP server" 169.x.x.x address.
I've tried reserving an address on the router and allocating it to the MAC address of the XDA, and manually setting the XDA to have that IP address, entering my router as the gateway, and even entering 2 valid DNS server IPs from my ISP into the name server entries. Still nothing. It says it's connected with the IP address I allocated, but I have no net connection, and I can't ping that address from any of my PCs.
All the while the status screen on the router tells me that the device, with it's MAC address, is connected to the router fine.
Surely this has to be something simple. I have set up all the clients and router for my network, and the settings on the XDA are pertty much the same, and really SHOULD be working.
I'm kinda at my wits end.
So basically any suggestions or advice, or anyone with similar experiences please get in touch, cos I'm struggling to see what I've done wrong, and it's giving me an ulcer.
Many thanks in advance.
Jess
3COM WAP (3CRWE454G72) - XDA IIi WIFI Problems
Hi Jess,
I very much share your frustration.
I have a 3COM WAP (3CRWE454G72) which has served me well. I have a few machines at home working from it. At work we have 20+ machines working from the same model (older firmware).
My specs are as follow:
3C number 3CRWE454G72
Software version 1.03.07A
Boot loader version 1.00.00
Wireless version V1.0.2.1
Hardware version R01A
Don't have the office one's specs here at the moment ...
At work I can get an IP address (there's a windows DHCP server) .. AND I can ping google and traceroute to google. BUT, XDA IIi doesn't seem "know" that it's connected (e.g. network settings shows the WAP as available, but not connected). SKYPE even works!! But nothing else, no IE, no Terminal Services Client, no Avant Go, no network ActiveSync. They all say that the is no network card configured (but with vxUTIL, vxIPCONFIG, etc). I can see ALL the IP details from the DHCP server.
At home it's worse. I can't even get it to connect to the WAP (either with WEP 128, WEP 64 or encryption turned off). As I'm not even getting an IP address at home from the WAP's DHCP server, I've built a new DHCP server on my one linux box and it works for all my machines ... now I can actually trace requests from devices for IP's ... and the XDA IIi never requests an IP address. Which tells me that it's not even getting through the first stages of connecting with the WAP (again tried WEP, NO WEP).
To make things worse. I have been able to connect to some open WAP's in the neighbourhood ... everything functioning normal.
I'm losing the will to live here also ... ;-)
Wolfie
the plot thickens...
Hi Wolfie.
Well, at this end I seem to have more news.
By removing all WEP encryption and removing the MAC address access restriction I had enabled, I got the XDAIIi online, and all was working.
I then enabled the security a step at a time, and at each step updated the configuration on the handheld, and it still all worked. I was so pleased.
)
However this morning I have come to put the thing online again, and once again it refuses to pick up a DHCP address.
I tried my process again, and this time it wont work.
It definitely seems that it's the encryption that's stopping it, but I can't get it working this morning.
When I disabled everything I managed to get it online, but then re-enabling the security killed it and I can't get it to come online again.
SIGH
Oh well, I will try again later. Fussy thing. Anyone ever manage to solve this ??
Jess
have u tried soft reseting the device and retrying, sometimes that cures these hiccups
rgds
jim
WIFI WOES
Jess, thanks for the reply. There's hope. ;-)
I have tried your approach yesterday. However, to no avail. At home I completely opened my WAP, e.g. any MAC, no WEP/WPA, etc. But still nothing. When I look at my log files on the WAP. I can see plenty of entries coming from my XDA IIi ...
04 min(s) 41 sec(s) after system power on : Wireless MAC address 00:09:2D:14:C9:F2 has connected with the device
04 min(s) 43 sec(s) after system power on : Wireless MAC address 00:09:2D:14:C9:F2 has connected with the device
04 min(s) 45 sec(s) after system power on : Wireless MAC address 00:09:2D:14:C9:F2 has connected with the device
04 min(s) 46 sec(s) after system power on : Wireless MAC address 00:09:2D:14:C9:F2 has connected with the device
04 min(s) 48 sec(s) after system power on : Wireless MAC address 00:09:2D:14:C9:F2 has connected with the device
04 min(s) 50 sec(s) after system power on : Wireless MAC address 00:09:2D:14:C9:F2 has connected with the device
... and it just goes on and on and on .... while trying to connect.
At the same time in all connections attemps, I don't get a single entry in my DHCP servers log saying that my XDA II attempted to connect.
Jim: I've tried hard resets, soft resets, O2 Active installed, Corporate mode, pretty much everything my single brain-cell can come up with. ;-)
The thing is definitely a little fiddly indeed ...
The search goes on ...
... anybody out there got their XDA IIi working with WIFI using DHCP and WEP or WPA?
Did you ever get this working?
I have a shiny new XDAIIi and have been trying to get connected via my Cisco Aironet 1200 WAP. The device happily detects my network, accepts the WEP key fine (complains if I enter the wrong key so I know it's communicating) but refuses to pick up an IP address. The Wireless LAN Manager just sits there "Scanning network..."
I firmly belive I'm just missing something but...........
Any help gratefully received :?
bump
I got my QTek 2020i today and for the life of me I can't get it to connect to the internet using my wifi connection @ home
I also have a 3COM router 3CRWE754G72-A and I have my home pc connected to this and also occassionally my work PC - both with no probs.
I can get the qtek to connect and I get a 50% signal strength and I can view an IP address and everything looks good but I can't seem to setup a "Connection" as required by IE?
This is what I get:
"Cannot connect with current connection settings. To change your connection settings, tap Settins"
I tap settings and I get this:
My ISP
Add a new modem connection
My ISP
Add a new modem connection
Add a new VPN server connection
Set up my proxy server
I've gone into each of these and had a "play" but I still can't get the bloody thing to work :evil:
Can someone PLEASE help as this is starting to drive me mad! - I'm not giving up easily...I've been trying to get this to work for a good 4 hours now and I can't find anything in the manual or on the web that helps...this post was the closest I could fine >>> hence the bump!
Cheers
Wayne
have you try to configure the network cards in the connection setting and set the internet using the tiacxwln Compatible Wireless Ethernet?
guoper said:
have you try to configure the network cards in the connection setting and set the internet using the tiacxwln Compatible Wireless Ethernet?
Click to expand...
Click to collapse
Okay, I can get the connection to read "connected" via the Wireless Lan Manager and I can get an IP address - which is totally different to all the other PC's that use my wifi connection - they're all 192.168.1.x whereas this is very different? - the address that I get isn't even the same as the IP Address of my router - I have a static IP address so I know this isn't changing???
Also, when I view the network card page I see the following:
Configure Wireless Networks
Add New...
3Com Available
I can click on this and view the settings for it or I can hold-click and get the option of connecting. If I do this, it just says "connecting"; it never actually says "connected"?
Anyone know where I can get a walkthrough for this?
Cheers
Wayne
3 Com Routers
Hi, DotN
I put a 3Com router in my local pub.
I have no problem connecting to it and solving the usual pub talk problems with it.
If you are getting a connection but your IP address starts with 169.254 then I would say you have a WEP problem. The software only appears to check for incorrectly formatted WEP keys, so either turn it off or make sure you enter the correct key. When selecting connect to a router the message sticks on connecting, come out of the screen and go back in after about 30 secs. Check you ip address. I have had some issues with GRPS trying to connect, but they seem to go away after a couple of hides.
I have to say that I am not over the moon with my XDA2i, but the wifi part has worked pretty well for me.
Laters
Paddy
Re: 3 Com Routers
MacPad said:
Hi, DotN
I put a 3Com router in my local pub.
I have no problem connecting to it and solving the usual pub talk problems with it.
If you are getting a connection but your IP address starts with 169.254 then I would say you have a WEP problem. The software only appears to check for incorrectly formatted WEP keys, so either turn it off or make sure you enter the correct key. When selecting connect to a router the message sticks on connecting, come out of the screen and go back in after about 30 secs. Check you ip address. I have had some issues with GRPS trying to connect, but they seem to go away after a couple of hides.
I have to say that I am not over the moon with my XDA2i, but the wifi part has worked pretty well for me.
Laters
Paddy
Click to expand...
Click to collapse
Hi Paddy
Thanks for the info. You're bang on with the IP Address!...169.254.x.x
So what encryption can I use?
I've deffinately got the correct password but it's obviously not working
Cheers
Wayne
Hi again
Okay, I've just checked the encryption and I'm using WPA-PSK authentication with TKIP encryption.
Is this what you had?
Cheers
Wayne
3 Com Routers
Are you using a password or 13 Hex pairs, I use the pairs. Try either turning wep of completely or entering 26 1s. Remove your setting for your ap in Configure Wireless Networks screen then reconnect.
Let me know what happens
Paddy
Re: 3 Com Routers
MacPad said:
Are you using a password or 13 Hex pairs, I use the pairs. Try either turning wep of completely or entering 26 1s. Remove your setting for your ap in Configure Wireless Networks screen then reconnect.
Let me know what happens
Paddy
Click to expand...
Click to collapse
Okay, I've basically removed all security from my wifi setup. I live in the middle of nowhere so it's not a problem - although once I get the wifi working I'll try and get the security going again.
I still can't get a connection
...stop the press!
Okay, I had a thought...maybe I can't connect because of the speed?
the router is a 11g but supports 11b (which is what the QTek 2020i/XDA IIuses) - sure enough, I had the 11g only option selected - DOH!
removed that and I've managed to connect without security.
I assume this was my problem all along...will now stick the security back on and try again
Thanks again Paddy
Cheers
Wayne
Update: I've now managed to get the wifi working with WPA-SPK authentication using TKIP encryption
all along it was simply a case of me having the speed on the router set above what the PDA was capable of! I'd set this ages ago when I first setup my wlan and had forgotten about it cause everything I use is 11g
Cheers again
Wayne
DotN said:
Update: I've now managed to get the wifi working with WPA-SPK authentication using TKIP encryption
all along it was simply a case of me having the speed on the router set above what the PDA was capable of! I'd set this ages ago when I first setup my wlan and had forgotten about it cause everything I use is 11g
Cheers again
Wayne
Click to expand...
Click to collapse
Doh!...nope, not working again...back to the 169.254.x.x problem.
It's obviously to do with the encryption this time. I'll try some other variations - at least I know that it can work :roll:
Cheers
Wayne
Ouch......
No hard feeling, glad you found the problem
Paddy
bump!
pretty much same prob!
i can get an ip, have to check what it is, it tells me its connected on the scanning network page but on the other bit it tells me its available or connecting but never connects!
i've turned wep off and still no joy!
its really starting to drive me mad!
please please someone help
Take a read back through the last lot of posts between myself and MacPad - I think you'll find the answer there.
For me, I had to totally disable my security and everything else - I could then connect. Once I'd done that, I managed to use WEP with a 26 digit key - start by using something like "0" 26 times...make sure u count as u type them zero's in though as if u get it wrong it won't work!
apart from that, not sure what to say. If you're getting the 164.x.x.x ip address though then as MacPad said, it's to do with the security.
I would mention that the XDAIIi/Qtek 2020ii use 11mbps wifi (b) and not 54mbps (g) so make sure u've got ya router configured to allow both types of connection...this eventually turned out to be my main problem - doh!
Cheers
Wayne
ok now im home ive re-read and done the things mentioned. with a completely unsecure connection i can get a connecation, but the moment i use any kind of encryption (im using wep 64bit, but tried 128bit as well) no matter what key i use i get a split second of connection then its gone!
firewall is not on either.
any ideas??
thank for the suggestions guys im finally progressing
I've been experiencing a strange Wi-Fi problem with my Cingular 8125 (using QTEK ROM 2.8.7.1 WWE). The device is programmed to support Wireless "G", and my access point is locked to "G only". I use PSK for security and TKIP for encryption. When I am around the access point, everything works great - I am able to surf at about 1 Mbps effective bit rate.
However, if I move to an area where the signal is less than 50% and then turn wi-fi on, I can't get a DHCP address. The device gets associated with the network (exchanges keys successfully), but no DHCP. If I program a static address, I still can't ping anything. The funny thing is, if I move even to the very edge of the coverage area with a DHCP address already acquired, the device communicates just fine. This happens both at home (Linksys WRT54G 2 running the latest OpenWRT firmware) and at work (unknown access point).
Any ideas?
Thanks,
Mike.
I have similar problems aquiring a DHCP address.
Particulary bad the situation is at home with my Netgear WGR614v1, even with full signal strength.
But also in other areas like my office building (unknown WLAN AP) I tend to have problems.
Sometimes it helps to turn off/on WLAN a few times or soft-reset the device.
But I never have problems to use WLAN when I enter a fixed IP address, but as I change locations often that is tedious...
I have an imate K-JAM with current original imate WWE rom.
Jammer said:
I have similar problems aquiring a DHCP address.
Particulary bad the situation is at home with my Netgear WGR614v1, even with full signal strength.
But also in other areas like my office building (unknown WLAN AP) I tend to have problems.
Sometimes it helps to turn off/on WLAN a few times or soft-reset the device.
But I never have problems to use WLAN when I enter a fixed IP address, but as I change locations often that is tedious...
I have an imate K-JAM with current original imate WWE rom.
Click to expand...
Click to collapse
This is a me-too post. I just got my MDA on T-mobile US.
I woud look at the router and saw that it did assign an address for the MDA, but I still did not receive an IP (showing connected, with 0.0.0.0 as IP.
Me Too!
Same problem here for US T-Mobile MDA.
If I manually assign the IP address info, it will connect to my WiFi router, but if left to DHCP, then it will try Connecting.... and fail.
What's the solution?
jonatj
i have the same (i think) issue with MN740 AP. I had DHCP lease to 2 weeks but chaning it to 30 min seems to fix the problem.
Well, I changed the type of lease from "get the first available address from the pool" to "static DHCP". This means that the AP recognizes Wizard's MAC address and always gives it the same IP.
It seems to fix the problem - now I'm getting an IP address instantly, anywhere in the coverage area. Of course, I can do this at home only - elsewhere I'm still out of luck.
It seems that this is a bug in the Wi-Fi stack of WM5, we can only hope that it get fixed soon.
Mike.
MDA Vario Wireless-G disabled by T-Mobile
I saw this posting at http://hardware.mcse.ms/archive34-2005-12-253197.html that says that T-Mobile has disabled Wireless-G on MDA Vario. I think this explains why K-Jam owners can connect to Wireless G access points and MDA's can't. At the same forum, one of the guys flashed his MDA with a K-JAM rom, and that fixed the problem. I hope someone can figure out the problem soon and create an update(I wish I knew how to).
I have an MDA, and I can't connect to G-only networks. I can see them (I think this is because the device is capable of connecting to G networks), but I can't connect to them.
Hello to all
I have problems trying to connect through wifi on my new 8125.
After reading a lot of threads, i downloaded a program called hitchiker, who solves the wifi connection a lot easier and faster, but i keep getting the same error, the wifi connection appears, it connects but can not solve the ip address with the dhcp server and fails...
Can anyone told me if this is a hardware problem or a firmware issue?
my router is a netgear WG602 v2 with the last firmware available.
Thanks and happy new year to all!!
ddo you have mac filtering on? if so try turning it off
No, i used to have a wep security password, but i reset all settings on the router to factory, to try to connect.
i also have a laptop and a psp and both connect great!!
dont know what the problem is here, but its frustating...
I make it to work
first i did a hard reset, then i check on the log of the access point, and it was going through and forwarding the connection to the adsl router, but the problem apparently was on the dhcp server on the router.
i add a fixed ip, and now it works
still not working on dhcp but at least its working...
tanquef said:
I make it to work
first i did a hard reset, then i check on the log of the access point, and it was going through and forwarding the connection to the adsl router, but the problem apparently was on the dhcp server on the router.
i add a fixed ip, and now it works
still not working on dhcp but at least its working...
Click to expand...
Click to collapse
I'm having almost the same problem.
First I've tried to connect on my open lan in my house. I could connect, but couldn't get an IP automaticaly.
Today I went to the mall to try some open wifi lan. A friend of mine, with a Nokia n80 succsessfully connected with one of the hotspots. I've tried and couldn't get an IP. Suddenly, don't know why, I got connected, but couldn't surf at the web.
Then I realized that the fixed Ip that I've set before was still on. Changing it for dinamic didn't work.
So, I still can't get an IP.
Any Ideas?
Hey Guys....I'm new to this forum, and it's already been a great help to keep my wizard going!
I have a new problem, that I'm not sure how to approach...I'm using IPL/SPL 3.08 + 2.71 Radio on the T-Mobile version of 5. (I'm at&T tho...)
Whenever I try to wi-fi into my home network, it finds my network, and tries to connect, but never gets an IP address assigned to it. I know it's not a hardware issue, because I've connected to other networks in the past.
I'm pretty sure there's a configuration problem some where (I'm using WPA security, but I couldn't connect even when the wireless was wide open) but I don't know if the configuration problem is on my router or on my phone. Any ideas??
Thanks for the awesome forum!!
Can you get hold of a laptop or another wireless device and see if this connects to your kit at home?
If it does then you know you have a problem with the phone, if not then it's the wireless router.
Yeah, I have a couple other wireless devices that connect wirelessly to the network already + I connected my phone to my parent's wireless a few hours ago...so it's gotta be the router, but I don't know what I have to change. Any ideas?
I myself have the same problem, I can connect, and MAYBE look at one or two pages, my phone then loses the IP and never re-leases it from the router....I aswell have other wireless devices that connect fine(such as this laptop that im typing this on lol)
Phone specs:
Cingular 8125
TNT 6.1 Pro/with TouchFREE
IPL/SPL 2.26.olip
SIM Unlocked
I have the same problem. phone connects and gets an IP but as soon as i try to go on the Internet, it stops working and then eventually tries to dial a connection.
I wonder if a static IP address would work for these issues?
Could you update the phone's Wifi profile for your router to a static address instead of a DHCP address then configure the router not to lease the phone's IP address to any other device.
any idea where to set static IP/DHCP on the wizard running 5.1?
Since I bought the HD2 before 2 month and after 2 Rom upgrade I still have the same Wifi problem. I can connect to my home network and the Router can see the HD2 but I can not connect to the Internet through the Wifi. All other computers and PS3 connect just fine. Ip adress seems also ok.
Please help ?
I did have the same problem a while back, and it occured after I used the wifi router. Have you ever used that, even just to try it?
No I never tried the Wifi Router even once and changed rom twice.
quincy67 said:
No I never tried the Wifi Router even once and changed rom twice.
Click to expand...
Click to collapse
Probably not the same issue then. For some reason I had it trying to give me a static IP address that my router wouldn't allow (I've got MAC forwarding on my router to make sure that nothing other than the 4 things I have can connect to it).
When you connect to the wifi, can you open the router admin on your HD2?
Thanks for your help. No I cannot access the router from the HD2, could it be a proxy issue. I am not using a proxy for the internet
quincy67 said:
Thanks for your help. No I cannot access the router from the HD2, could it be a proxy issue. I am not using a proxy for the internet
Click to expand...
Click to collapse
No worries mate - I hope I can help!
It's not a proxy issue, if you're not using a proxy server. Could you try this and let me know how you get on?
Start your wifi connection
Go to all settings, connection, wifi, wireless networks, network adapters tab
Select the Broadcom DHD adapter
It should be set to use a server assigned IP address, not a static one. It probably is, but it's worth checking.
When I open Wifi settings I can only open advanced no wireless networks or network adapter tab. How do I get there ?
quincy67 said:
When I open Wifi settings I can only open advanced no wireless networks or network adapter tab. How do I get there ?
Click to expand...
Click to collapse
After you've started wifi, go to the settings tab, menu and all settings. Then carry on the instructions in the last post.
Found the all settings, the DHD adapter is set to server assigned. Any other ideas ?
...
Well i think we have the same problem.. If you try to connect your wireless, do you get the failure after pressing get IP: Cannot obtain serverassigned IP....
http://forum.xda-developers.com/showthread.php?t=627654 my thread was this..
I found out that if i you go under WIFI>ADVANCED>press on the NETWORKCARD under the field "SSID"> then go to the networkcard>Broadcom 802.11 DHD network adapter>remove the pin in use serverassigned, and write a static ip: example: IP: 192.168.1.23
UNDERMASK: 255.255.255.0
STANDARDgateway: 192.168.1.1
That helped for me, though i cannot use that fix because my college wont accept the static IP. so it works for like 2 mins and then it disconnect. hehe.
Heh - that would be pretty much my next suggestion.
Try a static IP address and see if that works. It's not a long-term solution, but it would determine whether it's your phone or the router that's having the problem.
Last time I set a static IP address, I liked it and left it like that, but I found (after a couple of days with no internet access) that it tries to assign the same IP address when you use your data connection for internet access. Your service provider is very unlikely to allow you to use the same IP address, so you probably can't connect.
Like I said, it's a test to see if you can connect - not a solution.
Do you know what IP addresses your router will allow you to use? Do you have a specified range of addresses, for example?
I have this exact same problem. I can connect to wifi networks at home, office, etc... But no network access. It connects to the AP's, gives me an IP Address, but I can't ping anything!
This thing gets more and more frustrating daily.
skwizod said:
I have this exact same problem. I can connect to wifi networks at home, office, etc... But no network access. It connects to the AP's, gives me an IP Address, but I can't ping anything!
This thing gets more and more frustrating daily.
Click to expand...
Click to collapse
It also happened to me. Turns out it was the router I was using. I bought a new one earlier today and problem solved!
Hi!
I got a d-link dgl-4300 router, and had problem getting a IP adr. from it. When I gave my HD2 a static IP it worked, but very slow. After I changed from DHD network adapter to NE 2000 compatible ethernet driver it get IP from router and I can browse internet through wifi fast. Maybe it can help u 2.
regards Xes.