I am running WM6 on my 8525 but had the problem with WM5 too
32 bit Vista workstation running latest WMDC.
everytime I lift my 8525 out of the charging/sync cradle, I get the following error: "Windows Mobile Device Center Sync Host has stopped working."
Any ideas how to fix issue?
Problem signature:
Description:
Stopped working
Problem signature:
Problem Event Name: APPCRASH
Application Name: WmdHost.exe
Application Version: 6.1.6965.0
Application Timestamp: 465eef4e
Fault Module Name: unknown
Fault Module Version: 0.0.0.0
Fault Module Timestamp: 00000000
Exception Code: c0000005
Exception Offset: 53502105
OS Version: 6.0.6000.2.0.0.256.6
Locale ID: 1033
Hi everyone
Here's the problem : My Wiza cannot connect via usb, it charges and everything else seems fine but no data connect. I tried with my laptop with other usb cables, usb ports, usbkiller. The same situation. Plz Help.
Some information :
> XP SP2
> ActiveSync 4.5
Code:
Wizard Service Tool v4.2.2
20/01/09 16:40:30
CPU: Texas Instruments - OMAP850
MODEL: Wizard
=> Bootloaders:
IPL: 1.01 (G3 device)
SPL: 1.06 (G3 device)
Built on Nov 1 2005 at 16:44:44
Copyright (c) 2003 High Tech Computer Corporation
=> Firmware:
OS: 5.1.xxx (Build 14402.1.1.0)
ROM: 5.1
Registry AKU: .1.1.0
Radio: 01.01.10
Protocol: 4.0.13.16
=>Extended_ROM:
Version: 1.1.7.105
Name: Extended_ROM
Status: hidden
=> Drives and partitions:
|--Handle--|---Size---|
cfb7d5fe - 953.94M (0x3b9efe00)
6e9ef342 - 10.00M (0xa00000)
4eae8ede - 48.23M (0x303c000)
efb2bf42 - 51.06M (0x3310000)
2fb2bd82 - 2.88M (0x2e0000)
6fb2bd5e - 3.06M (0x30fc00)
All Done.
If your getting wiz service tool readings then im pretty certain its connected to a degree, did you enable rapi (that first thingy first)?
all solve here :
1st
need: MTTY
steps
1: Bootloader
2: mtty
3: task 28 55aa (fully format device)
4: rtask 0 (reset radio)
5: Reflash device
Above from wiki XDA dev's
Important, do not try to start device after above, after radio reset, put device back to bootloader directly
If above does not help you need to reflow or reball radio chip (tested and working if above does not work)
And my result from MTTY:
task 32
USB>password BOOTLOADER
HTCSPass.< YHTCEUSB>info 8
DOCInfoTableinitHW+
Binary0 Size: 0x100000
FAT0 Size: 0x4000000
FAT1 Size: 0x3340000
All Size: 0x7440000
FAT0_ADDR=0x100000,FAT1_ADDR=0x4100000
USB>info 7
HTC Integrated Re-Flash Utility for bootloader Version:1.50a SABLE EVT version:G.39
MainBoardID = C
Built at: Jun 12 2006 13:46:04
Copyright (c) 1998-2005 High Tech Computer Corporation
Turbo Mode Frequency = 312 MHz
Run Mode Frequency = 208 MHz
Memory Frequency = 208 MHz
SDRAM Frequency = 104 MHz
USB>info 4
HTCS Lњ3ЖHTCE
USB>task 28
DOCInfoTableinitHW+
Binary0 Size: 0x100000
FAT0 Size: 0x4000000
FAT1 Size: 0x3340000
All Size: 0x7440000
FAT0_ADDR=0x100000,FAT1_ADDR=0x4100000
USB>task 28 55aa
Wait..
DOCInfoTableinitHW+
Binary0 Size: 0x100000
FAT0 Size: 0x4000000
FAT1 Size: 0x33C0000
All Size: 0x74C0000
FAT0_ADDR=0x100000,FAT1_ADDR=0x4100000
USB>set 14 0
HTCST ЪИТHTCEUSB>set 14 10
HTCSF kEШ(HTCEUSB>set 14 9
HTCSF kEШ(HTCEUSB>
DONT PANYC after NO BOOT-> REFLASH CEOS.nbf (HW6915 ROM FOR G4-121UK) FROM HP Utility.
Info for Pass1:
HTCSPass1.CM€ЛHTCEUSB>password 0000000000000000
source:
http://forum.xda-developers.com/showthread.php?t=471942
final steps
If your Flash chip type is G4, you can use ENG V1.21UK rom to update, I have uploaded the rom to Yahoo.com mail box.
I have changed my 6965 CHT ver to ENG ver successfully.
You can login yahoo mail box by using [email protected] as id and 69656965 as password.
Pls note not to delete the rom as others might need it too.
Flsah method:
1. Sync your mobil with PC by ActiveSync4.5 or up
2. Double click the downloaded update rom programme.
3. Click upgrade button and wait for 8-10 minutes
4. Done.
source
http://forum.xda-developers.com/showthread.php?t=420041
please, don't chage anything. keep data safe for other people
has anyone tried the above instructions and succeeded ? I have a perfectly working 6915, but it's in Spanish and I would like to change the language to English. I'm afraid of bricking the phone or end up with the "No GSM" problem.
DO NOT USE that way.Surely, your phone will become a brick. That will change Product ID with invalid code and you will never restore SW for radio ROM .
It seems that there is about 100 MB Missing... I just guess is EXTROM
It could very easy to test that - different EXTROM but same Flash.bin.
The total free ROM space unchanged, even your EXTROM just used a few MB
If the EXTROM could be used, then it could be great help for cooking
The files may relate to FLASH.Header and partition.mbn. could anyone have a good try?
But...
pdocread.exe -l
411.25M (0x19b40000) DSK1:
| 1.87M (0x1df000) Part00 BOOT SECTION image
| 5.00M (0x500000) Part01 XIP RAM Image
| 84.25M (0x5440000) Part02 IMGFS file system
| 320.13M (0x14020000) Part03 legit DOS partition
handle#1 ef638fc6 320.13M (0x14020000)
handle#2 ef6adea6 84.25M (0x5440000)
handle#3 2f6ade82 5.00M (0x500000)
handle#4 4f6ade3a 1.87M (0x1df000)
Total is just 411.25, about 100MB (0x064C0000) seems missing....
For Part02, I could know is imgfs, and Part00 seems EXTROM, but where is disappear 100M?
partition table:
Code:
Partition-Info :
------------------
MIBIB
---------------------------------------------------------
Page: 0x6
Size: 0x4
Address: 0x000C0000 - 0x00140000
Block: 0x00000180 - 0x00000280
Flash: 0xFEFFFFFF
SIM_SECURE
---------------------------------------------------------
Page: 0x4
Size: 0x2
Address: 0x00080000 - 0x000C0000
Block: 0x00000100 - 0x00000180
Flash: 0xFEFFFFFF
FSBL
---------------------------------------------------------
Page: 0x180
Size: 0x1E
Address: 0x03000000 - 0x033C0000
Block: 0x00006000 - 0x00006780
Flash: 0xFFFFFFFF
OSBL
---------------------------------------------------------
Page: 0x180
Size: 0x1E
Address: 0x03000000 - 0x033C0000
Block: 0x00006000 - 0x00006780
Flash: 0xFFFFFFFF
AMSS
---------------------------------------------------------
Page: 0x4650
Size: 0x708
Address: 0x8CA00000 - 0x9AB00000
Block: 0x00119400 - 0x00135600
Flash: 0xFFFFFFFF
EFS2
---------------------------------------------------------
Page: 0x1F40
Size: 0xC8
Address: 0x3E800000 - 0x40100000
Block: 0x0007D000 - 0x00080200
Flash: 0xFFFFFF01
DSP1
---------------------------------------------------------
Page: 0x3E80
Size: 0x258
Address: 0x7D000000 - 0x81B00000
Block: 0x000FA000 - 0x00103600
Flash: 0xFFFFFFFF
FOTA
---------------------------------------------------------
Page: 0x80
Size: 0x64
Address: 0x01000000 - 0x01C80000
Block: 0x00002000 - 0x00003900
Flash: 0xFFFFFFFF
EXTROM
---------------------------------------------------------
Page: 0xC350
Size: 0x7D0
Address: 0x86A00000 - 0x96400000
Block: 0x0010D400 - 0x0012C800
Flash: 0xFFFFFFFF
APPSBL
---------------------------------------------------------
Page: 0x300
Size: 0x32
Address: 0x06000000 - 0x06640000
Block: 0x0000C000 - 0x0000CC80
Flash: 0xFFFFFFFF
APPS
---------------------------------------------------------
Page: 0x80
Size: 0xC
Address: 0x01000000 - 0x01180000
Block: 0x00002000 - 0x00002300
Flash: 0xFFFFFFFF
EFS2APPS
---------------------------------------------------------
Page: 0xFFFFFFFF
Size: 0xFFFF
Address: 0xFFFE0000 - 0xFFFC0000
Block: 0x001FFFC0 - 0x001FFF80
Flash: 0xFFFF02FF
good investigation ! I hope you can find a Way to reduce the allocated space, sadly I can't help you with this...keep the research !
Arto said:
good investigation ! I hope you can find a Way to reduce the allocated space, sadly I can't help you with this...keep the research !
Click to expand...
Click to collapse
Thank you also
The difficult problem is that, I'm not much understanding NAND Flash...
But, it seems that, after flashing ROM with new partition.mbn, the size of ExtRom could be changed.
At this moment, I'm not sure that the Hex files should be also changed or not ...
Code:
EXTROM
---------------------------------------------------------
[COLOR="Red"] Page: 0xC350
Size: 0x7D0[/COLOR]
Address: 0x86A00000 - 0x96400000
Block: 0x0010D400 - 0x0012C800
[COLOR="Red"] Flash: 0xFFFFFFFF[/COLOR]
Form Page (seems like format pagepool), the maximum ExtROM could be 50MB, that's the limit for a cook to modify ExtROM.
Of cause, if we could modify ExtROM size, then we could include more module in to Image
Moreover, including ExtROM, the boot system could used up to 93.674MB
my extrom take 7mb...so if the extrom allocated space can be changed it would be reallocated to application space? Qazer found a way to change page pool size, maybe it can help you on this !
edit, what is NAND flash?
Arto said:
my extrom take 7mb...so if the extrom allocated space can be changed it would be reallocated to application space? Qazer found a way to change page pool size, maybe it can help you on this !
edit, what is NAND flash?
Click to expand...
Click to collapse
After rearranged the partition table, it could be like this:
Code:
offset size
SIM_SECURE 0x4 0x2
MIBIB 0x6 0x4
FOTA 0x80 0x64
APPS 0x80 0xC
FSBL 0x180 0x1E
OSBL 0x180 0x1E
APPSBL 0x300 0x32
EFS2 0x1F40 0xC8
DSP1 0x3E80 0x258
AMSS 0x4650 0x708
EXTROM 0xC350 0x7D0
EFS2APPS 0xFFFFFFFF 0xFFFF
It could be much strange that some 'partitions' are overlapping!
Emmm, I forgot the order flashing these programs (.mbn), however, the ExtROM could be the last one to flash in the phone...
If somebody could tell me the order, then it could be much clear the process
Seems changed size could be OK, but I just wonder that what about ImageFS...
BTW, for term 'NAND flash', just wikipedia it
the best thing we can do is to reallocate this space in a virtual ram driver, and dont use the extrom space anymore. I noticed that the extrom files (cabs,tsk..) are in the windows folder of the device when you explore the windows folder.
So Is there a virtual ram driver or is there a way to do that, we don't need space, we need ram alternative.
anyway, don't know if it is possible to do such a thing on winmo devices...
( a kind of swap space....)
ocman said:
the best thing we can do is to reallocate this space in a virtual ram driver, and dont use the extrom space anymore. I noticed that the extrom files (cabs,tsk..) are in the windows folder of the device when you explore the windows folder.
So Is there a virtual ram driver or is there a way to do that, we don't need space, we need ram alternative.
anyway, don't know if it is possible to do such a thing on winmo devices...
( a kind of swap space....)
Click to expand...
Click to collapse
I think we should hardmod to add more RAM instead of using NAND flash, to avoid damaging it faster
Emmm, at this time I could not be sooooooo brave to flash my only phone
I just only change 0x7D0 (D0 07 00 00) to 0x3E8 (E8 03 00 00)....
If I try to flash with new partition.mbn,the phone turn into FTM Mode
But I just put partition.mbn, extrom.bin and two hex files only to the flash tool...
It sounds like I should put all files in that...
Then, finally these two hex files ENPRG8650.hex and NPRG8650.hex should be also modified.
Hi All,
I have been following the guide: http://forum.xda-developers.com/wiki/HTC_Vision#Restoring_the_backup_of_partition_7
To restore S-On on a Desire Z. I have tried both restoring the original image and using the S-On command as follows:
# ./gfree -s on
./gfree -s on
--secu_flag on set
Section header entry size: 40
Number of section headers: 44
Total section header table size: 1760
Section header file offset: 0x000138b4 (80052)
Section index for section name string table: 41
String table offset: 0x000136fb (79611)
Searching for .modinfo section...
- Section[16]: .modinfo
-- offset: 0x00000a14 (2580)
-- size: 0x000000cc (204)
Kernel release: 2.6.32.21-g6e170e7
New .modinfo section size: 204
Attempting to power cycle eMMC... OK.
Write protect was successfully disabled.
Searching for mmc_blk_issue_rq symbol...
- Address: c02adc1c, type: t, name: mmc_blk_issue_rq, module: N/A
Kernel map base: 0xc02ad000
Kernel memory mapped to 0x40002000
Searching for brq filter...
- Address: 0xc02adc1c + 0x34c
- 0x2a000012 -> 0xea000012
Backing up current partition 7 and patching it...
Backing up partition /dev/block/mmcblk0p7 to /sdcard/part7backup-315968429.bin .
..
patching secu_flag: 1
Done.
# sync
sync
# reboot
reboot
Despite this the status is still S-OFF
Please can someone help!
What is your rom version/build number?
what is your baseband version?
-Nipqer
Nipqer said:
What is your rom version/build number?
what is your baseband version?
-Nipqer
Click to expand...
Click to collapse
It was on cyanogenmod but it was giving me errors trying to restore it, so I flashed an official RUU:
ROM/ Build Number:1.82.405.1 CL317545 release-keys
Baseband: 12.28e.60.140fU_26.04.02.17_M2
Thanks
You need to run misc_version and downgrade to a 1.32 firmware, with radio 26.03.xx.xx to change back to S-ON
-Nipqer