does anyone know how to fix my phone the pins that connect to the battery fell off hopefully i dont need a new motherboard thanks for everyone with there thoughts about my problem
jbaker65401 said:
does anyone know how to fix my phone the pins that connect to the battery fell off hopefully i dont need a new motherboard thanks for everyone with there thoughts about my problem
Click to expand...
Click to collapse
It could be good news or bad news. If the contacts have broken on the surface then they can be re-soldered. If they have broken below the surface then that's probably the end of the motherboard. The Tyn has a multi-layered boardand breaks between layers are impossible to fix. We do not have a detailed circuit diagram otherwise it might be possible to solder on jumper leads instead.
Let's hope it's jus snapped at the surface. Either you or a skilled repair shop could do it.
Here is the board with the battery connector removed:
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
You can see the six solder points.
Mike
sweet i was thinking about that but didnt know if it would work or not now its just the six points on the bottom i got to do that to? what about the one on each sides?
jbaker65401 said:
sweet i was thinking about that but didnt know if it would work or not now its just the six points on the bottom i got to do that to? what about the one on each sides?
Click to expand...
Click to collapse
Can't remember to be honest - maybe they are just anchor points.
Mike
ill try it ope it works!! and thanks alot. i really like this phone
Related
Hi guys. Need help here. My ipaq won't charge even with te original usb cable.
It seems that the usb port is damaged - it charges only when i put a piece of paper in the mini usb connector so the pins of the connector are pressed against the ones on the usb port on the device. I guess they use too soft pins and they got deformed. Can anyone help me fix that. My device has no warranty.
I don't know if it is easy to change but this is what you have to buy :
http://www.repairhppda.com/product_info.php?pName=connector-for-synccharging-problems-for-610-612-614&cName=select-your-ipaq-model-ipaq-600-series
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Yep. That's the part. I found it later after I wrote the post. I guess I'll have to make a paypal account after all. Thank you thouugh. In the local service center they said they will fix it fo 15USD but I have to provide the spare part.
Any idea why this part has broken down? Is it possible to fix it without repacing it?
it sounds like either the small clip inside the USB port has snaped, or bent.
If its snapped, then theres very little holding it on so best to get it replaced
If its bent, then it may be possible for you to bend it the other way so it makes a stronger contact tot he USB plug. It will still be weaker than originally.
I have the exact same problem. The weird thing is that it still syncs and I can use WM5torage. I got around it by buying a cheap extra battery + external battery charger combo.
I tried boot my device and I scared cause In the screen is weird lines.
I attach picture of this and hope somebody can help me.
I also check all the adapters in the screen and opened the phone totally (all the screws) .
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
Niquel97 said:
I tried boot my device and I scared cause In the screen is weird lines.
I attach picture of this and hope somebody can help me.
I also check all the adapters in the screen and opened the phone totally (all the screws) .
View attachment 1606276
Click to expand...
Click to collapse
what were you doing with the phone ?
smileydr0id said:
what were you doing with the phone ?
Click to expand...
Click to collapse
I'ts dropped on the ground for about half metres.
It shouldn't be broken on this.
I will check the adapters off the screen again if some of these are loose.
Niquel97 said:
I'ts dropped on the ground for about half metres.
It shouldn't be broken on this.
I will check the adapters off the screen again if some of these are loose.
Click to expand...
Click to collapse
if adapters werent working you wouldnt have a back light on screen.im sorry but its broken..i had same thing when i droped it on stairs.
Niquel97 said:
I tried boot my device and I scared cause In the screen is weird lines.
I attach picture of this and hope somebody can help me.
I also check all the adapters in the screen and opened the phone totally (all the screws) .
View attachment 1606276
Click to expand...
Click to collapse
It's totally broken, just the screen, happened to me and cost me around $20.
search
u can easly find new screen on internet and how repair it
its cost around 20$
display is not the original the difference between the original?
i got a ls980 this month. it's beautiful and powerful. i do really like it.
but the GPS is too bad.
hard to search GPS signal and can not navigate.
i have tried to replace the GPS.conf file shared from other guys. but still,the GPS works not very good.
so i tried to fix it by modify the GPS antenna. like this:
step 1:
tape the 2 metal contacts. shield it.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
step 2:
find a copper wire,tie this metal contact；
close your back over；
tape the other end of the wire along the phone, just like the yellow line in my picture：
step3：
launch GPS test.APK, is it works?
this is my ls980's GPS signal after my DIY:
sorry for my poor English.
hope that it can help you guys.
way568 said:
<!-- Omitted for Brevity --!>
Click to expand...
Click to collapse
Cool :good:.
Next time don't spam to get 10 posts just to create a thread. Contribute to the community first.
My personal favourite reply of yours,
way568 said:
To prevent spam to the forums, new users must wait four minutes between posts. Sorry for the inconvenience!
too bad！！
Click to expand...
Click to collapse
Thanks, works like a charm. I wan't able to get a lock even outside, but "replacement" antenna works like a charm. I even get a lock on the floor inside the house.
Might try it as i still have issues
Hello Everyone,
So, I've bought a new logic board for my XT1563.
But, I think I forgot to attach some component, I see the screen lightning, the computer recognizes the phone, but I can't see anything.
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
The only missing part is the one that I've a red rectangle marked on the picture. I can't figure out how to remove this component from the old board and how put it on the new board. Someone knows how? Is this the cause for the display do not shows anything?
Thanks in advance and sorry for the bad english
Speaker? If similar to the Pure/Style, I think it just lifts out and is held in with some adhesive?
All ribbon cables properly seated to the display?
s
quakeaz said:
Speaker? If similar to the Pure/Style, I think it just lifts out and is held in with some adhesive?
All ribbon cables properly seated to the display?
Click to expand...
Click to collapse
Yes! It's the speaker sticked with glue. I heated a little bit and sucesefull removed it from the board.
So, that's not the cause from the display not working properly. The board is damaged and I asked for refund.
Thanks!
I need to buy it!
fiendaju said:
s
Yes! It's the speaker sticked with glue. I heated a little bit and sucesefull removed it from the board.
So, that's not the cause from the display not working properly. The board is damaged and I asked for refund.
Thanks!
Click to expand...
Click to collapse
Fiendaju, can you help me with one issue? Where did you bought this Logic Board (site)?
where you bought your board I need one too, and it's 32GB?
for thoose who have drain battery issues this can be the problem
{
"lightbox_close": "Close",
"lightbox_next": "Next",
"lightbox_previous": "Previous",
"lightbox_error": "The requested content cannot be loaded. Please try again later.",
"lightbox_start_slideshow": "Start slideshow",
"lightbox_stop_slideshow": "Stop slideshow",
"lightbox_full_screen": "Full screen",
"lightbox_thumbnails": "Thumbnails",
"lightbox_download": "Download",
"lightbox_share": "Share",
"lightbox_zoom": "Zoom",
"lightbox_new_window": "New window",
"lightbox_toggle_sidebar": "Toggle sidebar"
}
btw i cant find this on internet...something compatible?
Bruno41 said:
for thoose who have drain battery issues this can be the problem
View attachment 5522933
Click to expand...
Click to collapse
whats the problem here?
xtcislove said:
whats the problem here?
Click to expand...
Click to collapse
phone was draining current when totally off...like 460ma i toke appart and test the capacitors and components next to the ic were all shorted apply freeze spray to make sure and immediately that ic warm up, i remove that ic and shorts gone so im guessing that was the problem gonna replace see if works properlly
Bruno41 said:
phone was draining current when totally off...like 460ma i toke appart and test the capacitors and components next to the ic were all shorted apply freeze spray to make sure and immediately that ic warm up, i remove that ic and shorts gone so im guessing that was the problem gonna replace see if works properlly
Click to expand...
Click to collapse
btw toke me a while to find the manufactor( https://www.awinic.com/Public/Uploads/uploadfile2/files/20200515/20200515145039_5ebe3bbf4b71e.pdf) of this ic but i want to know if there is something better(compatible) like texas instruments?
I know this is a little off topic... But seeing a post for the OP8Pro with a 2022 date on it is refreshing! Been searching for days for information on how to flash a ROM/TWRP and/or ROOT and most posts are from 2020. I was beginning to think the device/projects were abandoned!
While on the subject, if anyone has recently and successfully accomplished any of the things I mentioned, would you please share? I have over a 100 tabs open right now from all the bricking I've had to come out of over the last 5 days!
Thanks!