Database Users

My Qtek doens't pass the red, green, blue screen

Hello,
Well to explain my problem. I had the RUU_Prophet_2151327_21513121_021921_DOP_ASIA_WWE_Ship-NoVendorID flashed onto my O2 XDA Neo. No problems, but sometimes I couldn't go back to desktop because "programms" didn't want to close. So I went to look for a dutch firmware. I found one and tried it. It didn't work, but my XDA Neo was already at 1% and didn't go further. So I pulled the cable out of the telephone. Now it doens't pass the red, green, blue screen when starting the phone. Hard reset doens't help eather. Wenn I connect it to the computer, activesync says "not connected".
On the screen it says:
RUU
IPL 2.15.0001
SPL 2.15.0001
Please help me out, because I really don't know what to do anymore

Encountered your case before while trying to downgrade with no success.
I suggest you try to turn back to dopod wwe rom and install it again before further attempts to brick your device.
Active sync tells it's not connected, that's normal because you connect a device which has no rom now.
You should see "USB" at the bottom of the screen once connecting to PC. Then start the rom update.
It will try to discover what's in your pda and will report you "nothing", which is logic. Click update and go. It should proceed...
Good luck.

g3k said:
Encountered your case before while trying to downgrade with no success.
I suggest you try to turn back to dopod wwe rom and install it again before further attempts to brick your device.
Active sync tells it's not connected, that's normal because you connect a device which has no rom now.
You should see "USB" at the bottom of the screen once connecting to PC. Then start the rom update.
It will try to discover what's in your pda and will report you "nothing", which is logic. Click update and go. It should proceed...
Good luck.
Click to expand...
Click to collapse
Thank you so much! I reflashed my old rom, and the device works fine again. But is it not possible to run an older rom? I would like to have the dutch version.

If your device is Sim unlocked, you may try the famous specific rom availIable at:
http://en.pdamobiz.com/en/forum/forum_posts.asp?TID=437&PN=1&TPN=1
This rom is for downgrading in a first step and cid unlocking in the second step exclusively and not for continous use . Once these two task are done, you can install any ROM you want.
Reminder: You can not install other language without CID unlocking.

g3k said:
Reminder: You can not install other language without CID unlocking.
Click to expand...
Click to collapse
It is not true. You can install any language ROM using NoVendorID patched reflashing utility.

Yes and no!
If the ROM to write is never "patched rom update utility" will bypass the CID check step and continue to install.
But it the new rom is older (ie 2.09 to write over 2.13) problems start there and you get an error in most cases. In that case we need to downgrade.
I've faced and practiced both cases.

Thanks for details...

help me!!!!! please i can`t start my P3300

anymore. :--(
Yesterday i^ve make a setup for the ext_rom but with a wrong update. It was been not for the Artemis..my fault.
Now i see only th et-mobile start screen and no more.
What can i do? Thanks in advance..

hmm, please flash your p3300 whith the original software with hope that it will be alive again. otherwise you can take an hardreset on your phone but i'm sure that there will not happened.
is your PDA an original fom HTC or from any other Provider?

it`s from t-mobile
and a hardreset doesn`t work and it`s not successful.
How can i flash it again...how i get usb connection to do it?

dr.moppi said:
and a hardreset doesn`t work and it`s not successful.
How can i flash it again...how i get usb connection to do it?
Click to expand...
Click to collapse
hello there!. i have the same problem, did you manage to get a usb connection? i can't flash it...

Try to get it into bootloader ( Read the Artemis wiki as to how to get into bootloader) and if you are successful then try flashing it with the t-mobile stock rom.

arvind09 said:
Try to get it into bootloader ( Read the Artemis wiki as to how to get into bootloader) and if you are successful then try flashing it with the t-mobile stock rom.
Click to expand...
Click to collapse
Please tell me how can i get the t-mobile stock rom or can you give me the link, thanks

Shipped ROM's in English - http://wiki.xda-developers.com/index.php?pagename=Artemis_Upgrades
To get into bootloader - hold down the record/voice command button (top left along the side of the phone) and use the stylus to press the recessed reset button on the lower left side of the phone (same side as the other boutton you hold down) Keep holding the record button as you hit and release the reset button, you will eventually see a screen with color bars on it. At this point you will be able to get a USB connection, but not an active sync. Try to start the ROM file when the phone is in this state and connected to your computer.
What is the original language/carrier for your phone?

MDA Compact III stops in T-mobile logo screen
I manage to enter bootloader and start flashing a ROM but I allways get a error: image file corrupted.
I think I need the original Dutch T-mobile ROM.
Anyone know where to find it?

Hi I have the same problem. I have the B&B3.7 and get stuck in the splash screen. I could enter to the bootloader mode and use some commands of the mtty.
I have my old rom, how may i load it to the pda? I have a SD and a tytn to load something in it.
Thanks!
Hernan

ftsv said:
I manage to enter bootloader and start flashing a ROM but I allways get a error: image file corrupted.
I think I need the original Dutch T-mobile ROM.
Anyone know where to find it?
Click to expand...
Click to collapse
run uspl first!!! you can then run installation from any provider of your choice.
http://forum.xda-developers.com/showthread.php?t=311403

USPL cannot be run if your phone is stuck into bootloader?
It starts counting, askts to copy the same information again several times, and get stuck at 50... how is this possible, anyone has the original HTC Dutch rom ? May be the WM5 also! Thanks!

same problem but with no display
i have done the same mistake
have tried to upgrade my T-MOBILE MDA COMPACT III(aka htc p3300) with the HTC TOUCH ROM
it started to upgrade and an error occured
then i have lost the display and all
when i connect it to my laptop using USB i hear a beep in my computer but active syn didnt find any device
i dont know what to do now..please help me it has to be recovered
there must be some way pls pls anyone help me to get my working phone back
will appreciate your concern
thanks
Regards
Faraz Feroz

well you have to get the original ROM for your device.. see their website.. it should be there for free. or try to get it from anyplace.. (the original rom)
and then flash it using SD Card flashing
info for flashing it by that are here:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
hope it will work

y_bother said:
well you have to get the original ROM for your device.. see their website.. it should be there for free. or try to get it from anyplace.. (the original rom)
and then flash it using SD Card flashing
info for flashing it by that are here:
http://wiki.xda-developers.com/index.php?pagename=Artemis_SD_Card_Flashing
hope it will work
Click to expand...
Click to collapse
thanks Y_Brother
i have downloaded the new rom but it doesnt seem to work too

probleme flash

Hello,
can some one help me please.
I try to flash my touch cruise and at 99% his stop.
after i just have 3 color screen and can't flash.
I try hard reset but it still color screen.
in the screen i got :
POLA100
SPL-1.25.0000
CPLD-2

Which rom did you try to flash on your device? I would suggest to check out the threads that relate to that rom. If you have used Olipro's hard-spl and followed all the steps for flashing the rom, maybe you could ensure your device is fully charged,that the file you have downloaded (rom) is not corrupted and try flashing it again.

shinshazz said:
Hello,
SPL-1.25.0000
CPLD-2
Click to expand...
Click to collapse
You had to hard-spl your device first!!

I have use Hard-SPL-V2 and when it get at 99%, it stop and then i get the 3 colors screen.
the rom I want to flash is the bepe 0.56.
Is my phone is over or I can get it work again.
I alreasy try to flash with the original HTC rom also, but don't work.

shinshazz said:
I have use Hard-SPL-V2 and when it get at 99%, it stop and then i get the 3 colors screen.
the rom I want to flash is the bepe 0.56.
Is my phone is over or I can get it work again.
I alreasy try to flash with the original HTC rom also, but don't work.
Click to expand...
Click to collapse
Sorry, just to be clear. It only gets to 99% of the Hard SPL V2? So the problem is not the rom you tried to flash but the Hard Spl?

The Hard-SPL-V2 that i have try is by Olipro, and I follow all the instruction.
I don't know why he stop at 99%.
I ask SFR, and they can't do anythink.
I think it's over for my phone .
I will try to ask HTC if they can do something and how it will cost.
hope give you good news .

Flash Problem
Hello,
I have the same problem...do you already have solution for your case ?!?!
Thank you in advance !

Ignore this post - I had IE troubles and double posted - See next post

Just to be very very clear since you are talking of HardSPL and of bepes ROM and mix all up:
You did not apply HardSPL to your device!
A device which has HardSPL applied would read "Pola100 MFG, SPL-2.20.Olinex, CPLD-2" at the 3-color-screen. Your device is still with the original bootloader. I suggest you try applying the HardSPL V2 again until it works or you get bored. Exactly follow instructions given in this thread: http://forum.xda-developers.com/showthread.php?t=370434

Hello, i had the same problem, i just soft reset my device and flash it back, it went up to 100% without any problem

Not working
Hello,
On device when I just connect the usb cable I get the three colour display with info:
POLA100
SPL-1.25.0000
CPLD-2.
Then I follow the instrutions, but when I get the step 7 the device appears always on 0% and get always the error 262.
Do you know how to fix this?!?!?

mrtgds said:
Hello,
On device when I just connect the usb cable I get the three colour display with info:
POLA100
SPL-1.25.0000
CPLD-2.
Then I follow the instrutions, but when I get the step 7 the device appears always on 0% and get always the error 262.
Do you know how to fix this?!?!?
Click to expand...
Click to collapse
You did something wrong. You have still original spl!
The correct steps:
Download hard-spl.
Plug your pda to pc.
On Pc run RomUpdateUtiliy (from Hard-spl folder)
Now you will see on PDA a tricolor screen and will be asked replug your usb cable. DO IT.
After Few minutes pda will reboot, hard-spl is installed.
Download the rom.
Now, STEP MANUALLY to bootlader. (press and hold camera, and press reset)
You will see a tricolor screen with OLINEX on your pda.
On the pc run the RomUpdateUtiliy (from the downloaded rom folder)
After Few minutes pda will reboot, new rom is installed.

See the images attached please.
I never get the "Replug information".
It's strange that Image version doesn't appear...
Thank in advance !

Now you will see on PDA a tricolor screen and will be asked replug your usb cable. DO IT.
On your PDA screen !
Not on your computer screen.

For information for my Polaris.
I found a phone shop in Paris, the boss of the shop say he can do something and I wait if he could or not.
Hope he will get me good news.

See this thread..
http://forum.xda-developers.com/showthread.php?t=373725

ActivSync - Flashing problem

Hi guys! It's again me
I have problem with flashing my X1.
Downloaded R2AA Generic English ROM. Installed 3.5 .NET framework on my Vista 64bit(all updates, including .NET 3.5 SP1), everythings suppa - when phone is ON - active sync detects, sync works.
Problem appears in that 4 color mode, where I want to upgrade ROM.
4 colored stripes and text appears, but when i plug the USB cable in.... on X1 it shows "USB" text but active sync doesnt detect the device. I just can't sync my X1 with PC while in that "ROM 4-colored mode" - and in progression - cant update my ROM.
Pls help
I want to install R2AA original, generic UK ROM by that method:
1:enter boot mode on X1
2:connect cable to PC and activesync the device (WinMobDevCentre)
3:run RUU and instal ROM's .image file
Because of temporary leak of mem.card

Have you tried running the program when connected with USB in boot mode?
Program should detect your phone

Active Sync is passive process.
How can I manually sync it?
Im in boot mode - entering USB and - no sync - so no ROM update

1. Enter boot mode
2. Connect with USB (when first time windows has to install drivers, wait for completion)
3. Run RUU (the program should recognize your phone)

1:entered boot mode
2:connected USB - windows installed device named "Microsoft USB Sync"
3:RUU doesnt recongnize connected device (no activesync connection)- cannot be continued

Hmm, let's try something else
1. Leave phone on
2. Connect to pc and WinMobDevCen
3. Run RUU

RUU gives me message: The update ultility could not open requested file.

Abuk007 said:
RUU gives me message: The update ultility could not open requested file.
Click to expand...
Click to collapse
Rename the image file to ruu_signed.nbh and place it in the same folder as the RUU utility

It runs! Thanks a lot
I hope it won't damage phone
...................
It crashed damn!
stopped at 10%.... i haven't HARD-SPL, thought generic ROMS don't require it...
What now ?

Abuk007 said:
It runs! Thanks a lot
I hope it won't damage phone
Click to expand...
Click to collapse
If you wait for the RUU utility to say the flash has been succesfull it won't be damaged....
Just don't do anything with your phone/pc during flash
Glad to be helpful...

Look my upper post :/

Abuk007 said:
It runs! Thanks a lot
I hope it won't damage phone
...................
It crashed damn!
stopped at 10%.... i haven't HARD-SPL, thought generic ROMS don't require it...
What now ?
Click to expand...
Click to collapse
You're correct, generic roms have radio and spl included.
Did ruu gave an error code?
ps you do need hard-spl if you're phone was originally in another language!

It had error. But I don't remember number.
On phone it writes: upgrade ROM code error
I had Vodafone R1AA UK ROM
Just want Generic R2AA UK.
Trying to fix...
using x1 Hard SPL to install R2AA UK generic.... will post result

Im getting 262 error.. even in Hard SPL...
HELP!
............................................
FIXED!
Don't know how
tried to run Hard SPL RUU - no effect - error 262
then runned normal, Kovsky RUU with same ROM - it worked!

Abuk007 said:
Im getting 262 error.. even in Hard SPL...
HELP!
............................................
FIXED!
Don't know how
tried to run Hard SPL RUU - no effect - error 262
then runned normal, Kovsky RUU with same ROM - it worked!
Click to expand...
Click to collapse
Probably hard-spl is installed even after the error, so you're abl to flash other rom than vodafone UK.
You can check this by going into boot mode and check what it says in the upper color bar.

it writes:
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707
so what SPL is it? hard or soft?

Abuk007 said:
it writes:
KOVS110
SPL-0.72.0000
MicroP1-787
MicroP2-707
so what SPL is it? hard or soft?
Click to expand...
Click to collapse
soft
hard says SPL-0.72.OliNex

THX a lot Lokatho for your great help! If there were any kind of credits on forum - you would get min. 100

Cannot upgrade ROM

Hello. This is my first time when I'm upgrading my Blackstone ROM and I get some problems so I cannot upgrade it
I think the problem is with active sync, but just I think like that maybe I'm wrong. First of all my active sync cannot connect the phone if the box is ticked for "Enable Faster Data Sync" I tried to reinstall active sync, version still not working. When the box is not ticked the active sync connect the phone but when I go into Rom upgrade setup and try to upgrade the ROM the phone restarts ant freezes in 0% of upgrade, then I get a windows with Connection Error. I take the battery out ant turn on my phone normally again.
Do you know how to solve this error? Or can you tell me other ways which I can upgrade my ROM? I know that its possible to upgrade via memory card but I don't know how. Thank you!

dnlaod any ROM, extract the file then u'll see a file named "ruu_signed.nbh"
change its name to "BLACIMG.nbh" then put it into ur storage card.
Go to bootloader mode then press power button n wait.. after ROM upgrade jus Hard reset it..
PS : read the WIKI

Sw1pe said:
Hello. This is my first time when I'm upgrading my Blackstone ROM and I get some problems so I cannot upgrade it
I think the problem is with active sync, but just I think like that maybe I'm wrong. First of all my active sync cannot connect the phone if the box is ticked for "Enable Faster Data Sync" I tried to reinstall active sync, version still not working. When the box is not ticked the active sync connect the phone but when I go into Rom upgrade setup and try to upgrade the ROM the phone restarts ant freezes in 0% of upgrade, then I get a windows with Connection Error. I take the battery out ant turn on my phone normally again.
Do you know how to solve this error? Or can you tell me other ways which I can upgrade my ROM? I know that its possible to upgrade via memory card but I don't know how. Thank you!
Click to expand...
Click to collapse
have u updated ur SPL... or r u using USPL..
IF u have then just boot into the boot loader and connect to USB and flash..
ignore the RUU saying that u need to be connected in active sync...

Moved out of development

cvchetan said:
have u updated ur SPL... or r u using USPL..
IF u have then just boot into the boot loader and connect to USB and flash..
ignore the RUU saying that u need to be connected in active sync...
Click to expand...
Click to collapse
I don't even know what SPL or USPL is. I told you this is my first time so i don't know those sort words. Can you explain properly what is those spl or uspl? thanks

bjy8138 said:
dnlaod any ROM, extract the file then u'll see a file named "ruu_signed.nbh"
change its name to "BLACIMG.nbh" then put it into ur storage card.
Go to bootloader mode then press power button n wait.. after ROM upgrade jus Hard reset it..
PS : read the WIKI
Click to expand...
Click to collapse
Thanks! I'm going to try your way today when I'm gonna come back to my home.

Sw1pe said:
I don't even know what SPL or USPL is. I told you this is my first time so i don't know those sort words. Can you explain properly what is those spl or uspl? thanks
Click to expand...
Click to collapse
This is all explained in the wiki. Before you do anything, best advice I can give you is to read up on SPL, USPL first!!!
Also, if you follow cRaCKwHoRe's guide (see my signature) you cannot go wrong.

Fallen Spartan said:
This is all explained in the wiki. Before you do anything, best advice I can give you is to read up on SPL, USPL first!!!
Also, if you follow cRaCKwHoRe's guide (see my signature) you cannot go wrong.
Click to expand...
Click to collapse
Ok. I will read it later. Thanks!

I'm still having a problem I have have read a wiki and I follow Dummies guide steps but I'm still having a same problem ( Stuck at 0% )
HSPL1 - Downloads
* (HSPL1a) HSPLWrapper_Blackstone_156OliNex.zip
* (HSPL1b) A 1.56+ based rom- Dutty's XT 3.7 linked here
* (HSPL1c) BlackstoneRUUWrapper.zip
* (HSPL1d) Extract each item to its own folder
HSPL2 - Flash new SPL (1.56.OliNex)
* (HSPL2a) Place your phone into its bootloader.
* (HSPL2b) Run HSPLWrapper_Blackstone_156OliNex.exe from the download in step (HSPL1a) and follow it as normal.
I follow these steps but at the last one my phones just freezes at 0% of update, so I can update to 1.56.OliNex SPL
Is me here doing something wrong or is it something wrong with my phone?

Does any one know whats wrong?

never mind. fixed by my self

Sw1pe said:
never mind. fixed by my self
Click to expand...
Click to collapse
how?? i have same problems..