So i tried to update my 8125 to WM6 using one of SNN's roms. And when i tried it, it said that it updated but then when the phone restarted it was still WM5. Oh and when i start up the phone it says its WM6 but when i checked in the settings it says its still WM5. Does anyone know what the problem is?
Related
Well this is the first time I've been unlucky for once. I've just finished cooking up some Rom for my ATT Siemens SX56. I was using the WM2003SE upgrading from PPC2002. I have a feeling that I did something wrong here and I'm guessing that I can't upgrade from PPC2002 and only WM2003? Well I'm not quite sure since I'm new to this. I successfully always upgraded the rom until now. After powering up, it started hanging at the startup logo with the version of the radio stack I think.
G1.3.3
UA.33
3.04
I've tried using ActiveSync and of course it didn't work. The cradle or A.S. did not recognize the device. Tried using XDATool, none. Is there anyway I could go around the ActiveSync?
Use sd card method for flashing.
tried that and it didn't work. I tried almost any methods out there. I tired upgrading from the original ATT Rom PPC2002 to the Special Edition 1.2 Rom and it still didnt work. What's odd is... I can't get my WM2003 to work anymore! When I first started upgrading the rom, I upgraded using SE 1.2, then downgrade to the original ATT rom back to the WM2003 which actually worked fine until I got piss at the radio stack and downgrade back to the PPC2002 but once I tried upgrading to WM2003SE, it didnt work at all which brought me to downgrade back to PPC2002 again and tried upgrading to WM2003 (ATT Version) which still didn't worked. I've tried upgrading the radio stack 6.24 and 6.25 and radio stack that would be compatible for the SX56 still didnt work. Even downgrading my bootloader from 5.22 to 5.15, it still didn't work. It's really odd... Can ANYONE help me?
I have similar problem, I have Qtek 1010 and I can put original rom on only (2002). I have had 2003 on there before and it worked fine but I have tried everything and nothing seems to work, all the 2003 and 2003se rom will not go past the boot screen.
Is your phone working at all.
My phone is perfectly fine, I'm just trying anyway to resolve that booting problem and so far, I'm getting no good results out of it... This is totally driving me nuts!
I tried neally every rom and I can't get any to work on my Qtek except the original 2002 Carrier device Rom...... I don't understand why we could both upgrade before with no worries and now it just will not work....
PLEASE HELP SOMEONE.....
THANKS
Well, so far I tried another rom, an older one and I still didn't get it to work... SD Flashing... The normal method with ActiveSys, it still didn't work. There has to be a reason to why this isn't working. Does ANYONE out there know whats going on here?!
I have been an idiot. In my haste to update my K-JAM to AKU2 with the new Qtek ROM I did not check which device was connected - I accidentally installed it onto my JAMin.
Now I am in a pickle, as I cannot put the iMate ROM back on. Hangs at 95% of install.
What can I do (apart from pray)?
Okay now
I retried the iMate ROM a few times (including ending half way through) and all seems to be fine now. Phew!
For the record, the Qtek Wizard ROM does not work on the Prophet!!!
This sounds like something I would do. 8)
I recently bought an SD-502 receiver for my XDAII and have no end of trouble since. I was hesitant to buy it given the compatibility problems but latest compatibility lists say that it has been tested and works. Long story short, COM 7: which is supposed to be assigned to GPSUART as per GPS PPC websites is absent and I cannot find any way to add it. I have upgrade from WM2003 1.60 to 1.72 and there was no change.
Further to this, I have downloaded the WM2005 upgrade in the hope that It would recognize the device but now I can't load any version of WM withouth the Himaupgrad.exe saying that there was 'a problem during upgrade'.
Thanks to anyone who chooses to help.
Can you be more specific about this 'problem during upgrade'?
That's what Himaupgrad.exe calls it... verifies the ID of the pda and then you click yes to upgrade and it goes to the screen where it clears the current rom and loads the 3 new ones and instead of doing that, after about 30 secs it just says there was a problem during upgrade and says to soft start the pda, which I have tried with no success. I have tried many combinations of Radio, Ex Rom and Rom without luck. I have even tried the original upgrade package that is already on there which I downloaded from the UK o2 site and that gives the same error. So I figure it is something to do with the PDA not the upgrades.
Again, any help is much appreciated!
Thanks jamil
Anyone got it?
Cingular SMT5600 = FUBARed
Hate to resurrect an old thread, but does anyone have or know where to get the full original Cingular SMT5600 ROM? I had loaded WM 6.1 a while back and all was well until I went to hard reset it to give to one of my brothers; it went to the bootloader screen and stayed there. I thought it was completely bricked until I found a full T-Mobile (German) ROM...loaded that up, got it unbricked, and was able to reload the WWE WM 6.1 again, but without a Cingular radio, the phone is still useless (though unbricked).
I've Googled my butt off, but keep running into dead ends..can anyone help?
Hello All,
I upgraded my EXEC to WM6 with the ROM of lucathebig. I did not upgrade the radio rom.
I don't know how it happened but, every time I switch it on, even without the sim card in, I can't access the phone settings! Or even the dialpad for that matter.
When I click on the signal icon, the balloon comes on but says "The phone is off"
When I tap settings nothing happens.
Please note that it was working a couple of days ago. I reset it to factory defaults but nothing happened.
Has anyone else got any suggestions? I will try to avoid flashing the ROM again and I'll keep it as the last option.
Update:
I noticed that there's no Radio version or IMEI on the system information on my phone so I figured that the radio got corrupted or something like that.
I tried to flash the Radio but i get the 114 error from the upgrade tool.
I tried all sorts of different upgrade tools with different radio version but none of it worked...
I am now downloading the official O2 update Xda_Exec_Upgrade_v113188.exe and try to install this instead to see if it fixes the Radio.
Has anyone found a solution for the 114 error? I have read tens of posts but can't seem to fins anything that helps. The people who solve it, use different versions of the update tools or they remove the USB hubs or try the upgrade 3 times.
Help ..?
I tried O2 update but the upgrade executable gave me a country ID error.
So I took the WM ROM and the Radio Rom from the zip file and tried to upgrade both but on the the WM ROM was updated. The Radio rom still gives me an error when I try to Flash...
Ohhhh this is so dissapointing.....