(elfin)bootloader - Touch GSM General

hello,i got a problem i tried to flash few roms and after when i tried them they were hanging up,so i downloaded another and i couldn't turn the phone several times but somehow it worked and turn on so,i was putting it on device by RUU and in 48% it stopped and show error message and after 4 steps i've done them and disconnected phone from pc,taken battery out that was in these steps and after when now i am trying to do a hard reset or soft reset it sometimes doesn't turn on and sometimes goes to bootloader that only what it's doing, i can't even do hard reset because it goes everytime to bootloader, i don't have idea what to do so please help me,is any way to flash rom without RUU?

Have you CID unlocked the phone already with USPL or HSPL? That would be the first step, and might be the problem.

i think i done,because in bootloader it says SPL 2.26.0000

yes, u can flash without RUU. rename ur rom file to ELF0IMG.nbh and put it in the root of ur sd card (formated in fat32).

so,that what i done i putted the sd card to nokia made usb connection between pc with xp and nokia transferred the rom on the sd card,unplugged nokia,token out card putted it to elfin and hold power button and it get me first to searching SD card communicate and after to bootloader and nothing happens, i leave it for couple of minutes on searching sd card communicate and nothing than happens i changed it to FAT32, the elfin is from orange uk.
PLEASE HELP ME!!!!!

NOW when i put the sd card in and keep camera and power buttons it get me to message "update sd image?" and "press power key to start download" but in this time it getting blinking and few seconds after screen go white,i am trying to press power but nothing happens appart turning screen into white PLEASE HELP ME UNBRICK MY PHONE.

Related

HTC hangs in bootloader after attempt to flash rom

Hi!
I have a HTC P3300.
I bought a 4Gb SDHC card, and it won't work. I read at the forum that I would need a different rom, so I downloaded "Artemis_Touch_4.02_Full_with_no_cube", which would have sdhc-support.
Then I executed "STEP 1 - activesync then uspl cid unlocking.bat", that finished ok, and then "STEP 2 - activesync then flash artemis touch rom.bat", which stopped with an error 302.
After a restart all that came up was the boot loader. I then tried to flash the original rom (HTC WM6 Dutch) from the computer, but that ended also in an error.
I tried the SD upgrade (rename .nbh file to ARTEIMG.nbh, put it on a formatted sd-card and load it in my phone), and it finished without errors, saying I should press any key.
After pressing a key, the bootloader popped up again.... :S
Can anyone help me? I have been searching the forum and trying to get my phone to work since 21:00 and I haven't got any progress at all!
well sorry for that
did you tried to make hard reset?
and once i had a completely dead artemis.. no sign of life..but it fixed by the following..(and maybe this may help you cuz the flasheng goes not like usual)
while your mobile is off.. press the record botton and the camera and it should starts with usual sd card flashing.
for me this what happens.
the setup was in three phases as i saw... and it took about 30 mins .
maybe it will works for you
I also tried a hard reset, wouldn't work.
I pressed and hold the camerabutton, but nothing happend...
Maybe the battery is empty, so I pressed and hold the camera button while plugging in the usb-cable.
It started the SD-upgrade, and is still busy.
The update ended with a "press any key to continue".
But when I pressed a key, the boot loader popped up :S
When I tried to flash another rom (NLD-FINAL), an error occurred (I believe it was error 270, not sure).
But then the normal startup screen appeared!
I don't know how, but the problem seems to be fixed!
sorry i mentioned the wronge button before..
try to start flashing by pressing the RECORED button and the power.. while your mobile is off.
and be sure that you copied the original shipped ROM to your device (NOT elese)
As you can see in my previous post, I managed to flash the original rom.
I'm gonna try to upload an other rom some other time...
And with a patch I got the SDHC working too!
Thnx for your help!
y_bother said:
sorry i mentioned the wronge button before..
try to start flashing by pressing the RECORED button and the power.. while your mobile is off.
and be sure that you copied the original shipped ROM to your device (NOT elese)
Click to expand...
Click to collapse
Hey, thanks a lot, I tought, my HTC-Cruise is ready for sending to repair, but with your info, it works again. I could install the WM 6.1 again, after System hangs up while booting every time. He found USB connection on a colored sreen. Thank you very much.
Jupeli

i reeallyyyy need somebody's help with unbricking my phone.. please hellpppp!!

alright.. i made a similar post to this before and i came across the wiki...
well i can't view what my SPL or my IPL because as soon as i turn the device on, all that shows is the boot loader screen and displays serial on the top with 0.16-0.90 in red characters on the bottom (I'm not sure what those are)...
here are the only details that i know about my phone:
I DON'T have hard SPL
My Original ROM i was using before was an htc windows mobile 5 rom
The reason that my phone is bricked right now is because the usb cable disconnected in the middle of the flash
I'm using Windows Vista for flashing
Computer won't recognize the phone when on usb
My phone (qtek 9600) can't load the operating system
*EDIT*
THE PHONE IS STUCK ON BOOTLOADER WHEN I TURN IT ON, NOTHING ELSE, BUT THE BOOTLOADER SCRREN DOESN'T SHOW MY SPL AT ALL.
ALSO, MY COMPUTER DOESN'T RECOGNIZE THE PHONE....... MY PHONE HAS A TYPE 2A BRICK
Helping me will be greatly appreciated
come on.. I'm without a phone
Do you have a 2GB or smaller SD card? Copy a rom image to it and rename it HERMIMG.NBH
Turn it on and you might get lucky!
Just make sure its stock rom that was supplied, or the updated WM06 version as the CID should check out then...
vwkess forgot to mention, reset into bootloader, hold power, ok button and reset with stylus. Hold all buttons in until you get to the tri-colour screen. If it works, follow the prompts....
Cheers...
hi,
i think i can hlep.
i had recently bricked my phone with a custom wm6 image, it worked fine for two days and then i reboot, and all i see was the welcome image, nothing else.
so what i did is -
i pressed the hard reset buttons - power + OK + SOFT RESET (Stylus), kept it pressed for 3-4 seconds, the fone rebooted, the screen was full with some colored bricks i connected my fone in USB and on screen i saw USB.
I then again flashed my fone with the working update, it worked perfectly for me, try may be you can get some luck
ps - before doing all these, i turned my fone off by removing the battery, i removed sim card and mmc card as well.
regards
That may work too, but again, try to flash with a stock rom, untick "connect with USB" in activesync and then try.
Make sure you go to boootloader screen, instruction in rajivlodha's post, before you connect to the pc.
Goodluck...
I need some help as well.
I think I may have bricked my phone. It's a rooted htc hero cdma. I'm running cyogenmod on it and it was working fine, until using metamorph to apply some changes to the theme.
I went to reboot, and it now it won't load past the htc screen. Even when i try the key combination to put it into recover mode. I didn't install a nandroid backup, and i'd be fine with just completely wiping my phone. help is appreciated.

SD Card Flashing Question!

Hello to everyone,
i have a problem with flashing.
First i had a WM2003 OS on the T-Mobile MDA. Then i tried to flash the WM2003SE with a romkitchen rom.exe over active sync.
The whole upgrade process worked well, but now it don't boots.
The booting procedure hangs on the welcome screen.
Now i am trying to flash a PPC2002 OS with SD Solution. (Because i have no activesync connection)
I have downloaded a *.nb1 rom from romkitchen and make copied it to SD with OS Image Tool.
But i don't know what to do now. When i insert the SD in the PPC it says only "The Card is not readable do you want to format it".
PLZ help!
Best regards
Andy
never heard about the bootloader saying that only a device saying it when it's booted into wm???
one way you can verify that the rom is flashed to the sdcard using the tool
the pc is no longer able to read the card
so that way you can verify that you did it correctly
Well, i did it by the same way (yesterday) ok, we can say you already have your SD card with your ROM ready for the instalation, so your put your SD car inside, then press the power button on top and press the hard reset button (you know it's down the earphones hole) it will apears the bootloader screen and the it will says press action to start or recort to exit, press the action button and it will start to donwload, it will finish saing COOLD RESET and something like that, take out your SD CARD and make a soft reset (the little hole at the other side of the hard reset) and that's it !!! i hope so jejejej let me know
thanx a lot. This worked for me!!

Help me (lost my ROM) :(

I was trying to upgrade my ROM to windows 6.1, and something wrong happened.
the update software hangs up on 0% also in my phone, form more than hour.
then I unplug the USB cable, and connect it again, the wizard told me that process will be resumed, but the same for more than hour and nothing happened when i reconnect it again it gives me error connecting
now my device is no longer working, it just give me a colored screen and nothing happened.
is there is anyway to fix my phone.
Is there anybody ? any idea ??
This might help.
http://wiki.xda-developers.com/index.php?pagename=Elf_SD_Card_Flashing
thank you jeremy,
I tried this method but it didn't work.
first i get the SD card and format it using windows (i tried both FAT, FAT32)
then extract the .nbh file from this package RUU_Elf_DOPOD_AU_1.14.710.2_4.1.13.46_02.97.90_BLUE_Ship.exe,
then i renamed it to ELF0IMG.nbh copied it to the root of SD card, then put the SD card in my device,
push and hold camera button and push the power button then the colored screen appeared but nothing happened. i tried also press and hold camera button then soft reset using stylus but it didn't work.
am i doing something wrong
Sorry i tired you
It should work.
It should say like ' do you want to flash your phone ' , press the power key to continue..
mmm, have you CID unlocked your phone?
have you tried flashing your phone?
how can i do that "CID unlock" ?
Go to the elf-upgrading forums and flash your ipl and spl to 3.10.
Cheers.
Can you start your phone in the first place?
no I cannot start my phone. it just freeze on the colored screen

[Q] Help!

Hey guys,
Sorry to be a burden but I'm having a few issues with my hd2, and being a noob I didn't really know where to turn except this forum.
Basically my dad bought the hd2 from the UAE early this year and it all worked fine on stock settings for about 6 months. In the last few months, however, the phone started to lock up, and it got to the point where it wouldn't even boot properly.
In an effort to fix the problem I went with a hard factory restore, however, this seems to have caused more problems as now the phone is stuck in the bootloader.
I've been searching for hours, and have come to the conclusion that I need to update the flash? and then possibly install a new rom on the phone?
My major issue in doing this though, is that I can't seem to connect to activesync while the phone is in the bootloader.
Please help me sort this out.
First of all lets make sure that your trying perform the hard reset correctly.......
You need to hold down both volume buttons whilst the phone is turned off..... Then tap the power button and keep the buttons held down.......
Release them when you see the confirmation screen.........
Powering on while holding only the vol down button will take you to bootloader....
If you need to reflash the device then have a read of this thread here....
If its a "Tmous" HD2 (green and red call/hangup buttons) then you need to read this one
When connecting to the pc in bootloader you should see the word "serial" at the bottom of the screen change to "USB".......
Might be worth checking the text on you bootloader screen for any irregular looking characters, there have a few cases of people with corrupt bootloaders, usually these will display odd looking characters at the top. This is quite rare though.
If you want to flash another stock rom then you wont need to worry about HSPL just download the appropriate ROM and follow the instructions on screen.
Start off at the HTC site and input your serial number to see which ROM is suitable for your device.....
If none of that helps then hold out for some advice here from someone with better knowledge of these things.....
Ok well I've just tried to do the hard reset in the way you've described and had no response from the phone. I had to remove the battery from the back to actually power down the thing as nothing else seemed to work. I can't actually seem to start it up again now =S
Thanks for all the info, I'll keep trying to get it started. I'm downloading the stock rom from the htc site. Hopefully I will find a way to install that.
Also, when the bootloader was up, there weren't any odd characters that I could see. It all seemed pretty standard. It had the current rom driver which was 1.42 or something and a few other lines of info.
Thanks for the post.
edit: perhaps the battery is dead?
No problem.
Is it charging when plugged in and turned off?
If so let it charge while turned off for a while and then try to boot........
If you cant get to bootloader and establish a USB connection then you could try flashing the ROM from the SD card.
rename the rom to "LEOIMG.nbh" place it on the root of a freshly formatted (fat32) sd card and turn on the phone holding vol down..
conantroutman said:
No problem.
Is it charging when plugged in and turned off?
If so let it charge while turned off for a while and then try to boot........
If you cant get to bootloader and establish a USB connection then you could try flashing the ROM from the SD card.
rename the rom to "LEOIMG.nbh" place it on the root of a freshly formatted (fat32) sd card and turn on the phone holding vol down..
Click to expand...
Click to collapse
To be honest I have no idea if it is charging whilst turned off =S All I get is the bootloader when it decided to turn on and that gives no indication of power level so I really have no idea. It makes updating a rom pretty scary haha.
So I just attempted to install the default rom from teh htc site, but failed due to the lack of activesync. It was strange though because the updater managed to change the screen on the phone and get to 1%. It then crashed and I had to go through this recovery process.
I will have to try this SD card process I guess. Could you perhaps link me to a more in depth guide to how to do this?
Thanks a lot for your help I really appreciate it.
you should get a red light up near the earpiece to indicate that its charging........
try this video for flashing from sd card......
I am not getting a red light flashing? But it doesn't seem to be running out of charge. I'm still having lots of trouble
It would seem that I need to install this hspl before I do anything, however, I can't install that if I can only access the bootloader screen. Does this mean my phone is bricked?
I want to be able to set up a rom straight from SD, however, I have no idea where to start. That video just seems to send me in a big loop.
Perhaps you could link me to a simple rom that I can attempt to load via sd card?
edit:
I seem to have somehow fluked an install of HSPL 8G XE.
I have no idea how this happened or whether it is good or bad.. but at least something has happened.
Hmmm
installing hspl is covered here
as long as the word "serial" is changing to "USB" on the bootloader screen when you connect to the computer you should be ok.......
You dont need HSPL to flash via sd card but I think that video was directed more towards people installing cooked ROMS from XDA.
Installing a stock rom will automatically overwrite HSPL so unless your planning to flash a custom ROM then installing HSPL is pointless........
You might be better off installing a cooked rom. (Artemis, Dutty's)
They tend to run better than stock, if you get one running then it will be easier to get back to a stock rom (if you want to) than the situation your in now.....
This is from the flashing guide;
Flashing Via MicroSD Card
NOTE (PLEASE READ): If you flash a Stock Rom via microSD Card then it will overwrite your HardSPL with a stock SPL included in the nbh file. This does not apply to custom roms as they do not include an SPL. BE CAREFUL!!
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the LEO Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to LEOIMG.nbh
4. Copy the LEOIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Reset the device while pressing the volume down button to enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
Reckon you could link me to one of those roms? I think we're getting pretty close now.
Your help has been great I can't thank you enough.
Your welcome
You can find Dutty's ROM here
or the Artemis ROM here
Have a quick read and see which one you think you'll prefer, to be honest I think they're both pretty similar to stock but with a lot of the crap taken out....
Just follow the steps in the first link I posted and you should be good to go.
Ok new problems.. Can you believe it.
I seem to have tried everything.
Basically I can install of a sd card, but when it gets to the end of the install and I restart instead of booting into a OS it boots to the tri colour screen, and starts the install process again.
Also, I have attempted to install via usb and have had varying success.
As I have already said, I am able to install hspl, however, when I try to flash I get to varying percentages below 30% before the whole thing freezes.
I now have an error that says Upgrade Rom code error Please Try Again.
Sorry i dont mean to hijack ! but will any of you be kind enough to help me here..
http://forum.xda-developers.com/showthread.php?t=879980
thanks !
Ok so I followed the steps and still to no avail.
I am able to boot using the sd card method, however, the same problem occurs with each rom version. Basically as soon as I reset the device it pretty much switches itself off, then I can't turn it back on, once I finally do turn it on, it restarts the process like it never happened.
The other issue is again the active sync problem.
With most of the the usb connections I am able to connect and get a little way through the install (most I've got is 15%) then it just freezes up and I get the 262 error
Your best bet is to try flashing with a freshly formatted (FAT32) 4gb, class 2 card.
I know, sounds pretty specific right?
You wouldn't think it would matter?
I have tried flashing with 16 gb class 2, failed at the radio step
Tried with a 8 gb class 6, failed at the radio
4 gb, class 2, flashed successfully.
Seems our HD2's are picky about what cards they'll take a ROM from for some reason.
Alright I'll try that, my next issue is which is the stock rom for the phone =S
It was bought in the UAE and I'm currently in Australia.
edit: Also I read somewhere that the constant bootloader screen can be caused by a bent battery pin?
Edit2: I have attempted to do that, however, now the bootloader will accept the card, then just sit on loading...
I'm pretty sure this thing is bricked.
tombm said:
Alright I'll try that, my next issue is which is the stock rom for the phone =S
It was bought in the UAE and I'm currently in Australia.
edit: Also I read somewhere that the constant bootloader screen can be caused by a bent battery pin?
Click to expand...
Click to collapse
I've heard of bent battery pins being a pretty common problem, causing usually just the phone not to charge properly. I've personally never heard of it causing constant bootloader, but it's definitely worth checking.
It's weird that it's such a common problem, my usb/charging port is broken, so I have to use an external charger. I change my battery on average twice every 24 hrs, and I've never bent a pin
Ok, new info, apparently because the device is for the middle east it does not support stock 3.14 roms. What does this mean for me? Am I bricked.
http://forum.xda-developers.com/showpost.php?p=9614007&postcount=30954
Click to expand...
Click to collapse
That's the post I found the info in. All of that info matches up to mine except my original image was 3.142 I think =S
Firstly, your phone is not bricked - a bricked phone is responsive as a brick.
Can we start from the begining?
What does the Bootloader Moder screen say (with and without the USB cable connected)?
What ROM (and if custom ROM, what RADIO) have you flashed and are trying to flash?
fred_up said:
Firstly, your phone is not bricked - a bricked phone is responsive as a brick.
Can we start from the begining?
What does the Bootloader Moder screen say (with and without the USB cable connected)?
What ROM (and if custom ROM, what RADIO) have you flashed and are trying to flash?
Click to expand...
Click to collapse
Alright from the beginning.
Basically about a month into using the phone in Australia it became very unresponsive to the point where it would not boot at all. We left the phone for a couple of months, however, after seeing a friend rom android I decided maybe it was time to attempt to fix this phone.
Some more info:
When I attempt to do any sort of ROM update there is nothing in the 'current image' part so for example it will say update to Dutty 3.6 but it's updating from nothing, does this mean there's no firmware there?
In the bootloader I have:
PB81100 HX-BC
SPL-2.08.0000 8G XE
MICROP(LED) 0X05
MICROP(TOUCH) 0X40
Without USB cable in I get Serial in the white part down the bottom, with the USB cable in + plugged into computer I get USB.
Just to further clarify. In regards to the ROM I have installed. I simply don't have anything installed. There is a bootloader, no image, no bootup. It boots up to the tri colour, that's it.
For a moment we will forget about going to 3.14 ROM: I don't know if that phone is entitled to an official upgrade to 3.14, if it is locked to a particular network, if it is branded, etc. If it is not entitled to a 3.14 ROM upgrade then you will have to go through GoldCarding, so we will leave it for now.
Make sure that the battery has had a good couple of hours charge in the charger or double that if connected to the computer.
Remove SIM Card and SD Card.
Switch on to Bootloader Mode, then connect to USB.
Download and run HSPL2 - ignore the instruction about connecting to ActiveSync etc, just proceed.
Download and install the HTC 1.66 WWE ROM - again, ignore the instructions, just proceed.
The reason for HSPL is because your phone may be operator locked (not SIM locked) and you aren't entitled to run the 1.66 WWE ROM.

Categories

Resources