wired headset and incoming call - Touch 3G General

Hi,
Experts needed...
I noticed the following "problem" earlier this day.
My wired headset was connected (but not in my ears) when I received (actually missed...) a call.
I noticed that the ringtone was not played through the loudspeaker/handset, but only through the headset.
I have PhoneAlarm installed which allow the sound to be routed to the handset even when a headset is connected, but this does not seem to work!
Is there any way (through registry or 3rd party software) to change this, and make the mobile ring instead/on top of the headset?
Thanks in advance for your insight!
BartV

bump! same issue here need answer.

Related

No Ring Tone when Using A2DP - Bug or By Design?

Greetings,
I'm using a Sony Ericsson HBH-DS970 stereo Bluetooth headset with my TyTN and so far I have only one gripe - when the headset is connected, the ring tone somes through the handset only, not the phone itself, which means that I'll miss any incoming calls if I don't have the earbuds inserted.
Also, the ring tone sometimes does not start until about 20 seconds after the display has started to announce the incoming call.
I tend to have the earbuds hanging from my neck if I'm not listening to music, and the ring tone is not loud enough to be heard that way.
I suspect this may be by design, because it's assumed that a stereo Bluetooth headset is always in/on the ears when connected to the phone, but I want to use the 970 as my only headset even when I'm not about to listen to music.
Is there any way to get a ring tone from both headset and phone?
/POL
?
Anyone figure this one out yet? I have the same problem...
same here, anyone find a solution please post, I think I can change it from the registry I will check it.
Can I ask you folks a question relating to the use of the headset Sony Ericsson HBH-DS970 with the HTC Hermes...do you get all the functionality ie caller ID, the ability to accept and reject the call, compatible with mediaplayer etc.
I have a concern that with the headset not being a HTC product, perhaps some of the Sony functionality may not work with the handset.
Thx
From my experience the ringtones will not come to the speaker if you use the headset as wireless stereo. I only use the headset as handsfree, which makes the ringtones go through the phone.
I used the DS970 for two week with my O2 Trion,feature like Caller Display is No any problem,But when using media player sometime it may out of control, like cann't accept call and control volume or stop.
And the sound quality is acceptable,but it will stop few second after 1 or minutes, I have change the regedit.
May I know is there any way to fix it?
Still no solution?
Anyone come up with a solution to this problem? It really bugs me not to get a ringtone from the unit itself, just thru headset... Works just fine with my old mono handsfree, would be great to have it in the stereo heaseat to...
i have the same problem
hello i have the same problem
the ring sound is only on my headset i have tested with 1.13.097fr and now 1.13.234fr if anybody have the ring on the phone with a headset stereo a2dp cang give us is configuration rom and other soft for the bluetooth.
thank and sorry for my english
juste a little frenchy
There seams as if there's no solution in sight, I got the exact same problem, also with HBH-DS970 and with Jetware Mobile's "Hands-free extension" installed.
I'm still running WM5, anyone who have tried WM6?
/Fluff
Same "design feature" here with my HBH-DS970 and HTC S710 WM6 Smartphone, so it's not ROM, device or OS version specific. I would suggest this is by design.
I'm pretty sure this is by design since thats how it works on my BT8010. Its stereo so it seems to make sense all sounds go through headset although it would be nice if it was an option. The BT8010 has a button on the headset to take it out of music mode so then they will go through the phone but I guess that doesn't help any of you out much.
Another option would be to just uncheck wireless stereo in the pairing and just check it back when you want to do wirelss stereo.

any way to have ringtones on BT headset?

Hi all, I have MDA Pro with BT headset Motorola H500. When I have call, the headset just play its built-in ringtone. I have set different tones for some 'important' contact and want to listen to them on BT headset, is there any software or registry tweak can do it? I used MS Voice Command and it direct the ringtone to the BT headset, but using that program was a huge memory consuming and not useful for a non-native speaker like me. Any help would be appreciated.
PS: sorry for my bad English.
Your headset needs to support the handsfree profile not just the headset profile for this to work.
When I tap & hold on the headset icon, there are 'set as hands free' entry, click on it has no effect, anything i can do to activate handsfree? TIA.
Not unless your headset supports it. If it did, you would hear the ringtones.
I am looking at some specs of the headset, it do support both 'headset' and 'hands free' profiles. But I cannot hear the ringtone of MDA Pro just the default ringtone of the headset. Any ideas? Thx.

Bluetooth headset and phone speaker questions

I just bought a bluetooth headset (SE DS220) which is working great - I listen to music and take/ring calls. However i have two strange issues I wonder if it is possible to fix:
1. While I am using the bluetooth headset my phone still rings if I receive an incoming call - I would like for the phone to be silent and for it to "ring" in my headset. If I turn off the sound in my phone then I can't listen to music either.
2. When I receive an incoming call I have to answer it with the button on the bluetooth unit - if I answer with the phone then the call is switched to the phones speakers. Is it possible to change this behaviour?
Thanks in advance!
/Hass
If your Device switch to the Phone Speaker ... you havent connect the Headset Profil in the Blue Tooth config.
NetrunnerAT said:
If your Device switch to the Phone Speaker ... you havent connect the Headset Profil in the Blue Tooth config.
Click to expand...
Click to collapse
There is a tick in the box for the headset profile and the icon comes up in the status field. It only switches if I answer with the buttons on the phone.
Noone has any ideas? Hasn't anyone else this problem?
I am not sure, but why dont you just answer the call with the headset.
PseudoReal said:
I am not sure, but why dont you just answer the call with the headset.
Click to expand...
Click to collapse
That's what I do - my biggest issue is the first question:
While I am using the bluetooth headset my phone still rings if I receive an incoming call - I would like for the phone to be silent and for it to "ring" in my headset. If I turn off the sound in my phone then I can't listen to music either.
BT headset problems
I have an xda2 i and I have the problem that even when the headet is connected, at times an incoming call won't broadcast over the headset at all, and equally if i dial out the call doesn't transfer to the headset.
Curiously, I've found the solution is to go into bluetooth manager -->active connections--> and click on STATUS of the head set connected. it should show signal strength and such. I double click on the CONNECTED message (oor maybe somewhere on the screen, basically double tap until it reads NOT CONNECTED ..... as odd as it sounds... this is what i needed... as when I do this, it usually works ok for me.
Maybe it will help?
..........IB a n e

No ringtone via bluetooth

Searched the Blackstone forums but did not find any post/thread regarding this particular problem .....
I'm a new Blackstone owner (and a newbie on this forum). Love the device but one major issue I have is that ringtones dont come through via the BT headset. I have assigned different ringtones to people and based on the tone of an incoming call, I should be able to screen calls without looking at the phone ..... or so I thought.
My phone : Blackstone (ROM 1.14.405.X). Dec/7 hotfix from HTC installed (since ROM is older than 1.19)
My BT : Jabra BT3030 stereo headset (AVRCP works fine)
Can anyone please help ?
Thanks !!
Try assigning a long ringtone as there is a lag and this may be cutting off the ringtone
Thanks winwiz. Tried that without luck. I only get the default beep-beep in the BT headset warning me of the incoming call ......
Bump !!
Can anyone of you folks help me with this ?
I tried a few tricks - set a looooong ringtone (2 minute song) ...... selected a single ringtone for all contacts ...... but no luck, still get only beep-beep via the BT stereo headset for incoming calls, while the phone itself plays the correct ringtone.
Funny thing though - music comes through fine on the BT (A2DP works fine) and I'm also able to control music without issues (AVRCP also works fine).
Any help/suggestions are welcome !!
Cheers !!
SLVRstone said:
Bump !!
Can anyone of you folks help me with this ?
I tried a few tricks - set a looooong ringtone (2 minute song) ...... selected a single ringtone for all contacts ...... but no luck, still get only beep-beep via the BT stereo headset for incoming calls, while the phone itself plays the correct ringtone.
Funny thing though - music comes through fine on the BT (A2DP works fine) and I'm also able to control music without issues (AVRCP also works fine).
Any help/suggestions are welcome !!
Cheers !!
Click to expand...
Click to collapse
I'm a little out of touch with the very latest gear - BUT - would the headset output the ringtone?? Surely it just has it's own ringtone that is the only one it can play, whenever a call comes in?
It seems to me that to send the .mp3 file over bluetooth to a device that doesn't seem big enough to have a full codec supply would tax the Bluetooth bandwidth somewhat!
SLVRstone said:
(A2DP works fine)
Click to expand...
Click to collapse
A2DP is used for stereo music, not for talking. Maybe its just not possible (with your headset). But I'm quite unexperienced with bluetooth headsets .
Riceburner said:
I'm a little out of touch with the very latest gear - BUT - would the headset output the ringtone?? Surely it just has it's own ringtone that is the only one it can play, whenever a call comes in?
It seems to me that to send the .mp3 file over bluetooth to a device that doesn't seem big enough to have a full codec supply would tax the Bluetooth bandwidth somewhat!
Click to expand...
Click to collapse
johnpatcher said:
A2DP is used for stereo music, not for talking. Maybe its just not possible (with your headset). But I'm quite unexperienced with bluetooth headsets .
Click to expand...
Click to collapse
Hello Riceburner .... today's Bluetooth headsets do indeed play your phone ringtone. But it should have A2DP feature that allows music to stream in and your phone should also have A2DP to "send" the music to your headset.
The .mp3 file does not get sent to the bluetooth .... the mp3 plays on your phone as a ringtone when you get a call and the A2DP feature then streams it to your BT headset where you then hear the ringtone.
This can have a lag of even a few seconds, hence the suggestion from winwiz a few posts back to use a long playing ringtone.
johnpatcher - A2DP is indeed not for talking, but it is necessary for the ringtone to play in your headset until you answer the call at which time the traditional bluetooth kicks in to handle voice.
Cheers !!
Can anyone help ?
Here is a consolidation of the issue and my attempts to overcome :
My phone : Blackstone (ROM 1.14.405.X). ROM date Oct/24/2008
Any hotfixes : Yes - since ROM is older than 1.19, applied the Dec/7/2008 hotfix from HTC that addresses screen freeze during multi clicks.
My Bluetooth headset : Jabra BT3030 stereo headset (A2DP and AVRCP works fine with the Touch HD phone)
Problem : Phone ringtone does not play through the BT headset. I get only a "beep-beep" on the BT headset for incoming calls, while the phone itself plays the correct ringtone.
Tried the following :
1) set a long ringtone (2 minute long song) as suggested by winwiz. No luck
2) Selected a single ringtone for all contacts. Still no luck
3) Paired the exact same BT headset with another phone (symbian OS) and it works perfectly - A2DP, AVRCP as well as phone ringtone comes through via the headset. Frustrated !!!
Any help/suggestions are welcome !!
Could this be a WinMo issue as opposed to a Blackstone bug ? Found the following thread ........
http://forum.xda-developers.com/showthread.php?t=310438
One way to find out ...... can folks spare a few minutes to post their experience in using A2DP heasets with the Blackstone - were you successfully able to hear ringtones via your headset ?
Cheers !!
*Bump*
Can folks oblige by posting their experience using A2DP headsets with the Blackstone ? Were you able to hear ringtones via your headset ?
Thanks !!
thread digger
sorry bringing this up again
but got EXACTLY the same problem here
tryied the suggestions too, without success
any tips?
[]s
I have a BT headset too that can A2DP. (SE DS-980) I don't think its meant for it to transfer ringtones as what one poster mentioned. Anyway, whenever my phone rings, I can hear the tone from my phone and a common single tone from the headset then the contact info is displayed in the LCD so I know who's calling. Another option is if you have MSVC, you can set it to alert you who is calling and only through the BT headset when it connected. That way you'd know who's calling you.
kieboy said:
I have a BT headset too that can A2DP. (SE DS-980) I don't think its meant for it to transfer ringtones as what one poster mentioned. Anyway, whenever my phone rings, I can hear the tone from my phone and a common single tone from the headset then the contact info is displayed in the LCD so I know who's calling. Another option is if you have MSVC, you can set it to alert you who is calling and only through the BT headset when it connected. That way you'd know who's calling you.
Click to expand...
Click to collapse
thanks kieboy
guess i'll install MSVC
I use my A2DP headset to listen to music on my embedded helmet speakers while in my bike. And of course, to answer calls too. So, looking to the phones screen isnĀ“t a option and the custom ring tones would be VERY usefull
but, if there's no other work around...
[]s

[Q] Problems with BT headset - SMS sound only in headset

Hey guys,
after a few days testing the BT headset connection in all different versions, i cannot get the LG to play the SMS sound from the device when my headset is connected. It plays the SMS sound only in the headset.
Phone calls are correct... the device rings and the headset makes it's typical sound.
I have a Jabra headset and it worked well with my HD2.
Can someone confirm this?
Any ideas how to solve this?

Categories

Resources