hi all
i ve got a big problem with my imate jam
i changed the screen for new one as the old one had a lot of scratches
the new screen was black band as the old one
the new one didn't work phone went on but no display
there i put my good old scratchy screen back on
phone went on but no display again with the old one also
now i have a phone that connects via active sync and do bing bing but no display
i have this phone like for ever and i did disassemble it thousands of time
any ideas about what is wrong???
Related
Guys,
My partner just closed my phone in her car boot. It works fine which is good however, half the screen is cracked and dead not good. Will it be chaeper to find a replacement screen, by another Trinity or move to something new.
Where could I by a new screen?
I appricated your comments.
Rich
think i have answered my own question...
http://cnn.cn/shop/p3600dopod-d810-screen-p-1734.html?osCsid=d538dc0645483ca7551cfc78c4c9fab2
anyone now anywhere in the uk?
do I need special tools to fit this?
Hello just for information,
I broke my trinity screen and I baught a new screen to a HK seller and i replace it.
I had already flash the firmware (faman 3.6 full) before changing the screen.
So everything seems ok when I put the phone power on but As soon as I put the creen off, I am unable to put it on it appears every time in a complete white screen !!!! to have something on the screen I have to reboot the phone.
I just reflash the phone again with faman 3.6 and it's still the thame problem completly white after turn the screen off then on ...
I try also an official orange WM5 (gps active) and the screen work's well i try after to switch again in WM6 and it doest work :white screen again ...
Can every one help me ?
@ Rich: Check the 'How to dissamble the Trinity' thread. Are your sure that the LCD is broken ? Could also be just the digitizer (USD 8 at cnn.cn.shop).
If you succeed to dissamble the display you should be able to attach a new digitizer.
The only problem are the two black levers ... (one for the display cable, one for the digitizer).
Good luck
Christian
I cracked my Trinity screen with a bad golf swing. Then I bought a replacement screen on ebay, found a disasembly guide, took my trinity apart, replaced the screen, put everything back together, and it works fine! cost me 70 EUR to fix it.
do it following the disassembly guide - taking the trinity apart is rather complicated, you will not figure it out by yourself.
Sometimes I wonder what the engineers drink before designing such complex assemblies!
Hi, a few month ago I accidently smashed the screen of my Vario. I decided to buy a new screen so I found one on ebay and installed it in my phone, however when I switched it on all I got was a white screen, no logos, nothing. The touch screen still works as I can hear the sounds when pressing it.
I am now being forced to go to a shop to fix it but I dont really want to shed out money for other people to do. Anyone know what could be causing the problem and how I could fix it?
Thanks.
hi
dont do with ur self u must send ur set to any expert person for evoid any more problems in ur PDA
Recheck the Flexi cable with which screen is attached,may be its detached or not fixed properly or even can be faulty.
Hi to everyone.
I dropped my wizard and lcd broke so I bought a new one and put it on. The problem is that although it takes phone calls and it syncs to pc, the screen is always white with nothing written..only a white screen. I do not know whether another problem occured besides the broken lcd. I tried to disassemble and reassemble it again but with no success. Any help please?
Hi, If my understanding is correct there are 2 versions of LCD for the Wizard. Are you sure that you have the right one? I'm sorry that I am unable to offer any further advice except to say that if the phone 'phones' and 'syncs' the basics must be working. Also the white screen means that the backlight is working - the problem is the LCD drive. Perhaps worth checking with your replacement supplier that they sent you the correct part?
Good luck!
OK I have had my T-mobile Wing aka HTC Herald since last April.
Just a few days ago I encountered a problem with my lcd. And I would like your guys feedback if possible before I purchase an lcd replacement.
My problem is when I slide open the wing my screen starts to fade, (almost making it look like a negative from a picture) after that it starts to fade to different colors.
Now the problem persists when the phone is closed, however if I tap the top of my wing and hold it the screen becomes normal, but once I let go it starts to fade again.
I would like to know if any of you experienced this with ur phone and if a replacement lcd screen will fix the problem or am I sol?
If it helps im running my wing on Open Touch v6.0 WM 6.1 Build 20273.1.3.3
Thanks in advance.
LCD problems
Hello,
I too have some weird LCD problems and instead of creating a new thread I thought of posting in this one.
For the past few months, whenever I get a call or resume my phone from standby mode using the power button the entire screen goes white or sometimes it has green or blue colored lines all over them. I have to keep on pressing the power button few times to get proper display. Also whenever I open the qwerty keyboard the display goes blank. Since I am out of warranty Tmobile is not ready to replace the phone and I contacted the HTC customer service and they told that the display unit and some hardware stuff is gone and it needs to be replaced and will cost a minimum of 170$ and will increase if they had to replace some other hardware.
Please note that, my screen is NOT broken and the touch screen too works fine. Recently the display has gone completely blank or too faded even to see whats there in the screen I could barely see the today screen.
I searched and I did not find any similar issues that other folks have faced. Since the LCD and the touch screen is not broken replacing them is not going to fix the issue, correct? I was using open touch and recently I updated the latest official Tmobile release of ROM 6.26.xxx. I also tried the hard resets too.
Any other ideas/suggestions will be of great help for me. Thanks in advance.
I am having some similar problems as well, but my problem is much more severe. My screen is completely black and it just happened this past weekend. When i slide the phone the screen used to flicker but now it black as well. Phone works fine but is useless due to the fact the the screen is out. I remember seeing a program where you can interact with your phone via your pc when something was wrong w/ your screen (cracked, broken, etc.) I have searched the forum but to no avail. The program was very simple and effective. I plan on replacing my phone but would like to retrieve some info off the one I have. I just need that program! Anyone please HELP US!
handsome22 said:
I am having some similar problems as well, but my problem is much more severe. My screen is completely black and it just happened this past weekend. When i slide the phone the screen used to flicker but now it black as well. Phone works fine but is useless due to the fact the the screen is out. I remember seeing a program where you can interact with your phone via your pc when something was wrong w/ your screen (cracked, broken, etc.) I have searched the forum but to no avail. The program was very simple and effective. I plan on replacing my phone but would like to retrieve some info off the one I have. I just need that program! Anyone please HELP US!
Click to expand...
Click to collapse
link to the thread containing some info about the software... its called my mobiler
thanks for the info
Greetings !
I am the proud owner of Qtek 9000 for sometime now.
Recently i was given a second unit, that at first look has a broken lcd.
The person who gave me the broken Qtek 9000 said that it had fallen off and then started to have the screen problem.
When powered on, the lcd displays blue and white lines during the width of the screen and the backlit does not come on.
If i plug the device to a Win XP machine, its get recognized and trying to sync
I assume the device must be working and this is an lcd only problem, although i have not synced it.
After reading around the forum and looking at the service manual on the wiki, i have disassembled the unit to see if any of the lcd connects got loose during the fall.
It seems that all connectors are in place, so my next task is to find if the lcd screen or lcd harness (cables) are broken.
Does anyone have any idea what i should replace ?
I have the same problem with red and white lines
Do you find what is wrong ???do you change the screen?
Welcome to forums
Try to do a hard reset (instructions on the Wiki), if not working perhaps you have to replace it, have a look on marketplace, one member is selling one
Good luck,