Xperia problem - XPERIA X1 General

Today in the morning i've wake up and checked my phone that was connected to a charger for last night. Power button were with a red light and a phone act like switched off.
Now, I can't turn it on and i don't now what to do exactly. I've tried a hard reset, nothing...
Does anyone had that problem???
Thanks for help.
Regards

First of all, if you want people to read your question, change the subject to something informative. Most people just skip these kind of non telling subjects.
Second, the problem. The red light shows that the battery is not charging, or that there is no battery at all. You could try to remove the battery for a while and then plug it in again. At start, when the battery voltage is below the normal 4.2V charging voltage, the red led is shown, but when the battery starts charging the led should go out. If this isn't the case, the battery could be broken.
You could also try a search on the forum, this question has been up before

And rather don't leave device to charge for whole night!

I have always left all my phones charging about 75% of the time I am at home (the other 25% is if I am tinkering with it and forget to plug it back in), so they are always 100% when I leave.
This shouldn't be a problem, although I also leave my phones turned on (standby) 24/7 as people mainly call me on my mobile rather than landline.

Related

Charging problem ..

(Bare with me, this IS wm6 related)
Okay, so i got this qtek 9090 from a trade online, and the owner pointed out that he had used it for some time now and it worked without problems.
However that seems not to be my experience. At first I was a little worried that it did not came with a charger.. Only a USB cable. No worries i thought, I will just charge it through USB. Now I have had some experiences where phones wouldn't charge from some of my computers, apparently because of some boards that put out lower amps than others. However I knew atleast one computer should have no problem charge ordinary cell phones.
So i plugged it in, and to my worries the battery kept going down... Untill the phone was dried from power and everything got lost again.. and again.. and again.. It seemed a little odd that it apparently deleted everything each time, since the backup battery indicated 100%.
So at last it went into flightmode and I shut it down with the powerbutton and let it be connected.. The first many hours nothing happened.. But suddenly, when i did an occasional check, it said 3% battery. I went to sleep and the next morning it was fully charged. I used it all day in school and it held its power real fine.
Now I got the feeling that this probably was caused by the low amp output from the computer, making it unable of charging to the extend where the phone would still be able of running whilst charging. So i figured i would order a 220v (the powercurrent here in Denmark) -> 5v USB that outputs 700mA, to make a quicker charge.
Well, to day I was gonna receive that adapter, and since I'd read that the wm6 apparently draines the battery some bit, I waited untill today to upgrade to wm6.
I upgraded and everything truely runs quick and stable. But when i recieved the adapter and plugged it in, i was horrified. The power kept going down, as I had experienced when it was plugged into USB.
Now my girlfriend really wanted to play bejeweled on this thing, so she did and then shortly afterwards we took a few hours nap. I had her plug it in the new adapter to charge it. When i woke up i saw the screen blinking.
I could se it was rebooting over and over again, as it had done the first time it completely lost power..
Now besides that extremely annoying charging problem, I now had another concern....
The boot screen shows NONE next to the R and the G.
Next to the D is the wm version displayed.
Any help would be greatly appreciated.
red LED?
Hm.. By doing a hard reset it shows numbers next to R and G again.
It continuely reboots, display boot screen, shuts down, LED is red, reboots, displays boot screen, shuts down, LED is red again and again.
If i hard reset it some times it will at one point stay off, but the LED still lights red.
And now I question wether 700mA is even enough for charging the BA?
1. Higher power given by power supply does not mean, you will get faster charging
2. If you use WM5/WM6 and have Bluetooth turned on, device turns on every few minutes (bug/feature of the driver needed to keep Bluetooth running: look for BigMike's fix for more information). If your deivce is set up to turn off after long time (for ex. 5 mins), battery might drain out in half a day.
3. Check power settings (delays for device power down etc.)
4. In WM6 be sure, that audio manager is not running (prevents device from deep sleep, allows only screen shutdown)
5. If battery shows up 100% and after disconnecting device discharges in less than 2h being turned on all the time (wifi, bt, phone, screen all the time turned on) it means, that battery might be worn. Consider exchange.
R and G showing NONE is normal in WM5/WM6 because of bug (unfixable for now) in the device and it's incomatibility with this OS: after turning on from power down (taking battery out or total discharging) make soft reset just when R NONE G NONE shows up on the screen. Everything will be normal.
jakubd said:
1. Higher power given by power supply does not mean, you will get faster charging
2. If you use WM5/WM6 and have Bluetooth turned on, device turns on every few minutes (bug/feature of the driver needed to keep Bluetooth running: look for BigMike's fix for more information). If your deivce is set up to turn off after long time (for ex. 5 mins), battery might drain out in half a day.
3. Check power settings (delays for device power down etc.)
4. In WM6 be sure, that audio manager is not running (prevents device from deep sleep, allows only screen shutdown)
5. If battery shows up 100% and after disconnecting device discharges in less than 2h being turned on all the time (wifi, bt, phone, screen all the time turned on) it means, that battery might be worn. Consider exchange.
R and G showing NONE is normal in WM5/WM6 because of bug (unfixable for now) in the device and it's incomatibility with this OS: after turning on from power down (taking battery out or total discharging) make soft reset just when R NONE G NONE shows up on the screen. Everything will be normal.
Click to expand...
Click to collapse
AFAIK the lower the mA output, the slower the charge period.
I have had wifi, bluetooth, beam off. I've set shutdown to 2 minutes. I've set it to low brightness and etc.
As i mentioned it had no problems going a whole day of usage in school.
Didn't know about the bug in wm6 that makes only the screen shut off, but at the momemt i can't even boot the device, apparently because it has no batterypower. And having it connected to the charger makes no real difference (other than it will display the bootscreen and perhaps even the Windows Mobile welcome screen thing, for a few seconds.. then go dead again.)
I've had it in the charger for about an hour or two, still not enough power to boot it up.
It feels like it's just not charging sometimes.. And other times it will charge just fine.
Found out about the reset to solve the NONE issue, but i still don't know what it means that its LED is red all the time?
Even 500mA is enough for sure, as charging from USB works fine.
Device will shut down soon after turning on if there is not enough power in battery, even it if is charging. Leave it charging (amber led on the right) for some time. RED led means low battery and no charging (AFAIR).
jakubd said:
Even 500mA is enough for sure, as charging from USB works fine.
Device will shut down soon after turning on if there is not enough power in battery, even it if is charging. Leave it charging (amber led on the right) for some time. RED led means low battery and no charging (AFAIR).
Click to expand...
Click to collapse
Hmm, i see. I just don't understand why it's not charging then :/
trylleklovn said:
Didn't know about the bug in wm6 that makes only the screen shut off
Click to expand...
Click to collapse
This is not a bug - thanks to this you can still listen to your music keeping device with screen turned off, when you don't need it to spare battery.
trylleklovn said:
Found out about the reset to solve the NONE issue, but i still don't know what it means that its LED is red all the time?
Click to expand...
Click to collapse
Red LED (right one) means low battery, no charging. To charge this led must be amber. Details - you must look for manual.
jakubd said:
This is not a bug - thanks to this you can still listen to your music keeping device with screen turned off, when you don't need it to spare battery.
Red LED (right one) means low battery, no charging. To charge this led must be amber. Details - you must look for manual.
Click to expand...
Click to collapse
Okay.
It's odd still. When i connect the charger the right LED starts to light red.
If it means that its not charging, there must be something wrong, since it only happens when connecting the charger..
it can be amber or red. Those are different colors and meaning.
You can confirm it charges touching the battery - it becomes slightly warm after some time.
jakubd said:
it can be amber or red. Those are different colors and meaning.
You can confirm it charges touching the battery - it becomes slightly warm after some time.
Click to expand...
Click to collapse
I KNOW that, but it is not going amber. It stays red all the time.
Found this thread that discusses a similar problem; http://forum.xda-developers.com/archive/index.php/t-233782.html
Apparently it shows RED light all the time if the battery is dead.. However i hardly doubt that the battery, which could power the phone just fine for and entire day, should be dead.
However, one suggestion in the thread was to take out the battery for some time and then try again. So I will do that for now.
Behavior has changed a bit now..
The LED is still red when i connect the charger. However, if i try to turn it on following happens:
Boot Screen shows for a couple of seconds...
Windows Mobile startup screen appears and the LED changes to orange/amber..
After a few seconds the screen turns black and the LED changes to red again...
And then after a few more seconds the boot screen appears again and everything is repeated, over and over.
If I disconnect the charger the boot screen appears, the wm startup screen appears, this time with a flashing red LED.. shortly after the phone turns off.
trylleklovn said:
Behavior has changed a bit now..
The LED is still red when i connect the charger. However, if i try to turn it on following happens:
Boot Screen shows for a couple of seconds...
Windows Mobile startup screen appears and the LED changes to orange/amber..
After a few seconds the screen turns black and the LED changes to red again...
And then after a few more seconds the boot screen appears again and everything is repeated, over and over.
If I disconnect the charger the boot screen appears, the wm startup screen appears, this time with a flashing red LED.. shortly after the phone turns off.
Click to expand...
Click to collapse
I've seen this problem before. The charger is not putting out enough power to both charge and boot the BA. So what happens is that it starts charging enough to start boot, but as soon as it has enough power to start the boot, it immediately drains it by starting to boot with screen at full brightness.
What I do in this case is to try to catch it just as it starts to boot and turn the backlight off by holding down the power button for 5 sec. This turns off the backlight so there is less drain and the thing can boot up and start charging.
All in all, its a pretty stupid bug but what the hell, there is a solution to it.
Good luck.
motisu said:
I've seen this problem before. The charger is not putting out enough power to both charge and boot the BA. So what happens is that it starts charging enough to start boot, but as soon as it has enough power to start the boot, it immediately drains it by starting to boot with screen at full brightness.
What I do in this case is to try to catch it just as it starts to boot and turn the backlight off by holding down the power button for 5 sec. This turns off the backlight so there is less drain and the thing can boot up and start charging.
All in all, its a pretty stupid bug but what the hell, there is a solution to it.
Good luck.
Click to expand...
Click to collapse
This seems to work atm. (just a few seconds since it successfully booted)..
Does this mean that the device really cant charge if its not "on" ?
(I can see its booted and the LED is now orange. If only it will stay this way untill it has been recharged further ))
trylleklovn said:
This seems to work atm. (just a few seconds since it successfully booted)..
Does this mean that the device really cant charge if its not "on" ?
(I can see its booted and the LED is now orange. If only it will stay this way untill it has been recharged further ))
Click to expand...
Click to collapse
It can charge when it is off. BUT... When its off, its not really off... It has to finish booting and then you can turn it off. Then it will charge faster as it only has minimum drain on the battery. As I said before, its a stupid design.
motisu said:
It can charge when it is off. BUT... When its off, its not really off... It has to finish booting and then you can turn it off. Then it will charge faster as it only has minimum drain on the battery. As I said before, its a stupid design.
Click to expand...
Click to collapse
Well we can certainly agree on that
So does the phone also basicly use to much power to be used and charged at the same time? Which would explain why it seemed to lose power even though it was connected to the charger.
Although it still doesn't add up for me, as at one point i was playing a game on it, while charging and then it charged real fast, where you would expect it to use more power
Oh well, if only it keeps charging now i'll be glad
trylleklovn said:
Well we can certainly agree on that
So does the phone also basicly use to much power to be used and charged at the same time? Which would explain why it seemed to lose power even though it was connected to the charger.
Although it still doesn't add up for me, as at one point i was playing a game on it, while charging and then it charged real fast, where you would expect it to use more power
Oh well, if only it keeps charging now i'll be glad
Click to expand...
Click to collapse
I have found that if you only use the USB cable to charge, it takes much longer (if at all) to charge if it is on. Thats why I bought cradles that have external power suppies as well as the USB sync cable. With this configuration, it gets to full charge in about 90 minutes.
Hm.. yeah.. I let it charge for some time, until it shut down and the LED changed to red again.. The same thing has happened about 3 times now.. If I try to navigate it with the brightness off it will shut down after a few clicks..
Seems like either the battery is completely dead or it's simply not charging.. :/
Think i have to buy a new battery and a cradle, although i didn't really want to spend money on this phone as i got it virtually for free (through a trade of a w810i)
trylleklovn said:
Hm.. yeah.. I let it charge for some time, until it shut down and the LED changed to red again.. The same thing has happened about 3 times now.. If I try to navigate it with the brightness off it will shut down after a few clicks..
Seems like either the battery is completely dead or it's simply not charging.. :/
Think i have to buy a new battery and a cradle, although i didn't really want to spend money on this phone as i got it virtually for free (through a trade of a w810i)
Click to expand...
Click to collapse
Get it to orange and then push the power button (short push) to turn it off (not long push which only turns off the backlight). Then let it charge for an hour or 2 (or even all night). By then, it should work OK.
motisu said:
Get it to orange and then push the power button (short push) to turn it off (not long push which only turns off the backlight). Then let it charge for an hour or 2 (or even all night). By then, it should work OK.
Click to expand...
Click to collapse
Yeah, i tried that. As soon as i press the power button it goes to red again.
Update..
A litte update (i might as well document everything I find out here, if anyone should run into a similar problem).
Now, I've had the device connected to the charge for some time now.
What happens is that the device boots up, automaticly dimms down to no light (since i once had hold down the power button, to dimm down light).
Then it boots up, and i can see everything running.
I can navigate to the battery status menu, which shows
Battery: 0% (charging)
Backup battery: 25%
After a few minutes the device shuts down, and the LED goes red again. But after about a half a minute it will try to boot up again, and it goes through everything again.
What I've noticed is that the backup battery slowly increases, and while im writing it has gone all the way to 75%. The good thing about this completely automatic procedure is that it apparently slowly charges, at least, the backup battery.
My theory is that the backup battery has first priority in the system, so that the regular battery wont charge untill the backup battery is up. And since the backup battery can't apparently be used for actualy powering the system, the system will continuesly reboot because of lack of power, theoreticly untill the backup battery reaches 100% and it starts to charge the regular battery.
The whole problem seems to be cause by some charging malfunction, so that both batteries has been completely discharged. I hope that by letting it continue to reboot, charge, reboot, charge, etc. it will revive the battery.
I will return with more info tomorrow.
Any suggestions are still greatly appreciated.

Battery Died, phone wont charge nor turn on...any ideas guys?

as the title says....any help anyone
anyone....?????
elite-fusion said:
as the title says....any help anyone
Click to expand...
Click to collapse
so strange, i think this is not a fault of battery, because lithium polymer battery is really long lasting, have you connect your x1 to computer, please connect your x1 to charger and wait about 1 hour. but maybe it's the fault of mini usb port, can you sync your x1 before it happen? in your case, bring it up to guarantee service is the best solution, what did you do before the device turn off?
Leave it on the charger, it could take about 15 - 20 minutes to start charging if the battery completely died.
i used a wall charger, and a computer charger, still no luck...i wasnt doing anything, i was playing a game and shut the game off started browsing through the fone, and it just shut off after a few battery low warning sounds. but the red light goes on after a wall charger, but nothing when i try to turn it on, it doesnt turn on, and when i unplug it to try to turn the phone on, the side lights flash red...i have no idea whats goin on but i got the phone today and its pissing me off already i spent 680 on the phone for a peice of crap...
elite-fusion said:
i used a wall charger, and a computer charger, still no luck...i wasnt doing anything, i was playing a game and shut the game off started browsing through the fone, and it just shut off after a few battery low warning sounds. but the red light goes on after a wall charger, but nothing when i try to turn it on, it doesnt turn on, and when i unplug it to try to turn the phone on, the side lights flash red...i have no idea whats goin on but i got the phone today and its pissing me off already i spent 680 on the phone for a peice of crap...
Click to expand...
Click to collapse
ah, you should keep it in the wall chager a bit longer, and don't use the computer charge at this time, when the battery complete die, you should keep it charge about 10 minutes before you can start it, don't worry, when you can see the flash light turn red, it's charging, wait a few minutes more, it's will work, just forget about it, go somewhere, when you comeback, push the power button:d
elite-fusion said:
i used a wall charger, and a computer charger, still no luck...i wasnt doing anything, i was playing a game and shut the game off started browsing through the fone, and it just shut off after a few battery low warning sounds. but the red light goes on after a wall charger, but nothing when i try to turn it on, it doesnt turn on, and when i unplug it to try to turn the phone on, the side lights flash red...i have no idea whats goin on but i got the phone today and its pissing me off already i spent 680 on the phone for a peice of crap...
Click to expand...
Click to collapse
was had same problem.just leave it charged.i leave it charged into usb drive,and it needs 5h before he turn on.battery was completely dead,like probably you have too.just leave it charged throught the night.
Charge some time and then remove battery cover and try to reset. as u mentioned lights are flashing when u r trying to switch on so just reset.
The X1 of my colleague had the same problem and he had the battery replaced by the vendor, no questions asked as it was dead after only 2 days...
Charged without battery...
elite-fusion said:
as the title says....any help anyone
Click to expand...
Click to collapse
Hi, I got similar problem and I called the support guys.
They advised me to remove the battery and charge the phone for 30 min and charged with the battery for 1.5 hour.
He claimed is some 'internal battery' stuffs.
Anyway I tried and it works.
In addition, I charged the battery when the level hits a minimum of 20%.
So far so good
Good luck.
vwx1 said:
Hi, I got similar problem and I called the support guys.
They advised me to remove the battery and charge the phone for 30 min and charged with the battery for 1.5 hour.
He claimed is some 'internal battery' stuffs.
Anyway I tried and it works.
In addition, I charged the battery when the level hits a minimum of 20%.
So far so good
Good luck.
Click to expand...
Click to collapse
That Solution worked for me as well. I was in Germany with some navigation software to find my destination address. Than suddenly my phone died, I thought. So I was stuck somewhere in the middle of nowhere.

Flashing red led of death

Hi everyone, yesterday I took my G1 from my pocket (after using it normally for some hours) and it was turned off. I thought the battery was dead (I left it at about 20% charge) so I tried to turn it back on and surprise...no vital signs at all. The phone didn't turn on, and the led was dead. After losing half of my hair, I tried removing the battery and placing it back. Now the phone behaves like this; when I press the power button, as long as I keep it pressed the led flashes red and that's it. When I stop pressing the power button the led stops flashing. When I plug the usb cable, the led gives a solid red and stays like that forever.
Please someone tell me it's just a screwed up battery...please
Neuromansa said:
Hi everyone, yesterday I took my G1 from my pocket (after using it normally for some hours) and it was turned off. I thought the battery was dead (I left it at about 20% charge) so I tried to turn it back on and surprise...no vital signs at all. The phone didn't turn on, and the led was dead. After losing half of my hair, I tried removing the battery and placing it back. Now the phone behaves like this; when I press the power button, as long as I keep it pressed the led flashes red and that's it. When I stop pressing the power button the led stops flashing. When I plug the usb cable, the led gives a solid red and stays like that forever.
Please someone tell me it's just a screwed up battery...please
Click to expand...
Click to collapse
Probably bad battery. It is certainly worth it to at least try another battery -- they're dirt cheap anyways, or better yet, BORROW one.
* Solid green (when connected to the power adapter): The battery is fully charged.
* Solid red (when connected to the power adapter): The battery is charging.
* Flashing red: The battery is low and needs to be charged.
* Flashing green: There is a new notification.
Neuromansa said:
Hi everyone, yesterday I took my G1 from my pocket (after using it normally for some hours) and it was turned off. I thought the battery was dead (I left it at about 20% charge) so I tried to turn it back on and surprise...no vital signs at all. The phone didn't turn on, and the led was dead. After losing half of my hair, I tried removing the battery and placing it back. Now the phone behaves like this; when I press the power button, as long as I keep it pressed the led flashes red and that's it. When I stop pressing the power button the led stops flashing. When I plug the usb cable, the led gives a solid red and stays like that forever.
Please someone tell me it's just a screwed up battery...please
Click to expand...
Click to collapse
Leave it to charge for 30 minutes or so, then try to power on. should be okay
better to charge from ac power if u can
Its possible your charger could be faulty.
I have the same problem, has anyone found a solution?
Try leaving it charge for a good hour, or just go out and try a new battery, could just be dead.
Sent from my Xoom
sometimes if a battery gets to low it wont even charge... not just for phones but cameras too and so on..... iv had to do this to cell phones and cameras.... take a usb cord you dont care about and cut it and expose the red and black wires..... look for the positive on your battery and negative, usually its marked, how positive to positive and negative to negative for 30 seconds to a minute while its plugged into the computer then, pop the battery back into the phone and try to charge..... everytime iv had to do this for a freind or something of my own the battery has lasted over a year after with no problems.... just a suggestion
Thanks for the suggestions. I had already ordered a new battery and the phone boots up with it but it won't charge on or off and usb isn't recognized either. I tried wiggling the plug around to see if it was some kind of loose connection but it doesn't appear to be the case. I may take the phone apart and see if anything is loose but otherwise I'll just have to enjoy the last 30% battery of G1 time I have.

[Q] battery problem, red led light is blinking, bought new battery, no bettering

Hi guys!
I know, that there are some threads about the topic, but i think, here it is a bit different...i´ll describe:
Everything was OK with my withe G1, since I forgot to recharge the battery, and the G1 switched off. I wanted to recharge it, but - you know- the red led light blinked...i read different threads etc, and then I decided, to buy a new battery. The new battery arrived yesterday, and I put it in my G1, tried to switch it on, and it worked. I was quite happy! I taped it on the charging unit, and the first problem: the battery display didnt moved, it remained at 23%, also after a few hours at the charging unit. I knew the problem, because it was the same with my old battery, but it doesnt interest me, because the battery recharged, only the battery indicator showed that not. I thought OK, dont thinked about it, and waited. Today: I took my G1, yes, battery display at 23%, no problem. I switched it off and after a few hours I wanted to switch it on. Second problem - F**K! The red led light blinked...and now, the battery doesnt recharge at all. The G1 works now only, if the charging unit is put on it, if I remove it, the G1 switchs off. Its the same behavior with the old battery.
I dont know what to do now, because i dont think, that it is a hardwarebug, because yesterday it worked, with the brandnew battery. Or is it possible, that the G1 destroys my batterys while switching it off?
I hope, that there are solutions for this...because im loosing my temper slowly...
Can you charge the battery if the phone is off? Red led light should show. You should wait even 30-60 minutes for this - it depends of battery discharge. If the red light will not show this will means that your hardware is broken (phone or phone charger). You can try use another phone charger to test.
That works sometimes....at the moment not, but one hour before, yes.
I had the G1 with the USB cable on the PC, the phone was off, the light was red (not blinking). I waited about 50minutes, then disconnected, tried to switch it on - nothing except a red led light - blinking
At the moment, there isnt any led light, if i connect the phone to the charger unit or the PC...
It looks like hardware problem :/
Would be OK, because there is still warranty.
But what irritates me, is, that it worked without problems, when the battery was charged. Also with the new battery...worked good, since I switched the phone off.
I only want to be sure, because the return merchandise authorization (rma) takes quite long time...
I have the same problem. last week i bought the phone, and used it till the phone battery was empty. I tried to recharge the phone, but i wouldn't go on, only the red light blinking. I had the phone charged for 2 days, with the og charger, no result. Looked like the phone was dead.
Today i tried it again, still no result. All of a sudden the phone turned on and was charging. It is now on 99%.
Should i contact HTC?
edit:
sorry, wrong forum
Just a wild guess. It could also be the ROM that you have. I had a similar problem with my battery drained out like that with flashing red light. Come to find out later that it was something to do with the ROM (CM6.x) that I was using.

X2 Charging problem

So the phone was really low, at 6% this morning. SO I put it on the wall charger. I saw the icon come up that it was charging and then put the phone down.
A while later I went back to the phone and saw that although the charger was plugged in to the wall and also plugged into the phone, it was NOT charging.
Using the phone I went to my contacts to check a phone number and then it turned off, due to no charge.
I plug it into the wall charger, the USB connected to the computer, as well as the car charger and here is what happens:
The top and bottom of the phone blink red for about 1-3 minutes.
Without pressing anything on the phone it automatically turns itself on, I see the Sony Ericsson boot screen, the Windows boot screen then my SPB Mobil Shell screen for about a second and then it turns off again showing and the blinking red light for about 1-3 minutes and then it starts the process all over again.
I think that a setting for Backlight/Power management was changed. As setting similar to "Only charge with usb", or "only charge when connected with ActiveSync" or somthing like that.
The problem is that I turned off the Active sync on the phone in order to conserve battery power so that I could look up the phone number from my contacts. And after I did that the phone shut off and I cannot change it, because it will not charge.
I do not have a different, charged, battery to try and do not think that I can find one easily.
Any suggestions?
Now when I see that the phone is re-booting(I see the SE logo), I use the stylus to to soft reset. It is obvious that there is some type of charge happening before it re-boots, , otherwise it would not re-boot. SO my theory is that by doing a soft rest between restarts, the battery will gain more of a charge each time. And possibly have enough of a charge so that I can go into my settings and see the backlight/ power settings have been changed.
So I took a battery from my old SE 902 phone and rigged it to work with my X2.
It booted up just fine. I was able to get into the menu for power settings. Nothig was changed however I did check the box "do not charge when connected to the computer" backed out of that screen and then went back into the screen and unchecked the box.
I powered down the phone and the screen went to the default charging battery meter.
I then put the proper battery in the phone and it was still blinking red. I saw it blink green for a few seconds, then I felt it vibrate, and then I saw the green battery meter. But after a few seconds it went back to blinking red and I could not see the battery meter again.
This seems to be happening intermittenly. As of right now there is a green blinking light and I see a dimmed battery meter.
Hopefully it will be fine, we shall see.
So it was charging for a while and now has stopped. I see the battery meeter, but there is no green bar moving up. and the light has stopped blinking.
I unplugged the usb and I still see the battery meter with no green bar moving. Installed the back cover and plugged the usb back in.
Now it is back to the red blinking again. . . ? ? ? ? ?
I think that it is a battery issue.
CAn anyone suggest why a battery would all of a sudden stop working?
Just ordered a new battery. $70.00!!! Ouch!!!
It does come with a battery charger for use with a Mini USB, but still, $70.00 is a lot of money!!
I will update with the results after i charge it up.
I got the new battery and put it into the charger. As I mentioned in an earlier post the new battery came with a separate charger for use with a mini usb. At first I had problems. The charger would not charge the new battery. I was using a wall connected mini usb to power the charger. So I went to the computer and tried the mini usb from there. It still would not charge. So I took the battery out of the charger and put it into then phone and went back to the wall charger and it was charging. I could feel the phone vibrate and then saw the battery meter slowly fill with green and back to empty and then fill green again.
So I decided to do a few other chores around the house and went to check the charging status after about 10 minutes. I noticed that the phone was on!! I did not turn the phone on. No one else was in the house to turn it on. It was just on. Weird.
So I took the battery out of the phone and decided to try the new charger again with the computer mini USB. It WAS charging this time!! I charged the new battery on this charger using the computer mini USB until the red light(charging) turned green (finished charging) and then put it in the phone. It works fine.
I then decided to put the defective battery into this charger and it was actually charging!! I left it overnight and it was green this morning: identifying it as a full charge.
When the new battery is down to 10% or less I will take it out and put the defective battery in and see what happens.
So I put the original battery back in after the green light came on identifying a full charge on the accessory charger.
It showed 1% and a message came up identifying that "the battery is low, please charge asap", something like that.
So, in my unprofessional opinion , the original battery is toast.
The new battery worked great after its initial charge using the included accessory charger.
When I decided to charge it using the phone itself with the wall charger I noticed some really weird things happening.
First of all you should know that I downloaded and installed Spoon Charge. Look it up here on the forums, free and works great. It basically tells you what charge level you have, temperature of the battery, what voltage is coming in to charge it and also type of charge the battery is doing: trickle, fast, very fast and on battery.You can set it to read reading at specific time intervals: I have it set to read at every second.
I noticed that the charge kept bouncing between very fast and trickle. At one point it went to on battery, then to trickle then to on battery then to fast.
Ok. Weird. . . I thought to myself.
So I let it continue to charge overnight.
The next day I "tried" to use the phone. it was as slow as it was at it's factory installed settings before I did the memory card fix, accelerator settings, and other fixes that I forgot now have forgotten that I have installed.
At this point I decided to drain the battery as fast as I could by turning on WiFi, Bluetooth, and play a movie at the loudest volume possible. As soon as it reached 10% I took the battery out and charged it with the accessory charger. The next morning I saw that the indicator light was green showing full charge and installed the battery in the phone. It booted up and I immediately received a message that the battery was low, saw 1%.
Knowing that this was a BRAND NEW BATTERY, I turned off the phone and took the battery out and waited a few seconds until I put it back in and rebooted the phone.
This time it said 86% charge!!!!!!
WTF!!!!
So I tried to use the phone and it was as sluggish as before. After about 25 minutes it was starting to be a bit faster but nothing like it was before.
I am really confused now. Since I have a new battery I have ruled out that as a problem. So now is it the phone itself? Could it be the wall charger that is faulty?
Any other suggestions would be greatly appreciated.
Another update.
I put the original battery in the phone and now it works!!!! The old battery that would not charge now charges and works!!!
The phone is not the same. Still really slow, can't get it out of the "LOCKED" position when I want to answer a phone call. Opera is sliggish then fast then sluggish. Not what I had the phone at before all of this started. It actually WAS stable. It WAS useable. Now I want to throw it into the drink!!!!!!
Not sure what to think anymore.
well bro go into the system help of ur mobile press as i say
2ce the end button one time call button, 2ce the end button one time call button,one time end button and u will find the problem it is in the charging port the same issue with me

Categories

Resources