Sync date and time to cell phone tower? - 8125, K-JAM, P4300, MDA Vario General

I'm trying TNT ROM and it keeps locking up, so I remove the battery to reset the phone. Unfortunately, this resets the clock and date to 2006, which screws up call logs, appointments, etc. when I forget to fix the date/time.
My old phone would sync the time/date every time I turned it on, getting the info from the cell phone tower/network (when I went to California, for instance, the phone was automatically on local time). Is there a program to do this for the Wizard/PocketPC? I know of programs that sync to NTP (TNT comes with one that doesn't work), but that's no help when I'm not connected to Wi-Fi.
At the very least, could it save the time to the memory card so that it doesn't revert all the way back to 2006 when the battery is removed? The time would be wrong, but at least it wouldn't go back in time compare to when I turned it off.

No, the Wizard does not feature either flash memory nor a battery back up for the date and time. Newer HTC devices do, but the Wizard for whatever reason doesnt.

Is there a way to sync the phone's clock to the cell phone network?

No. I've found that the easiest way to sync the time is with active sync. I use a atimic clock sync on my computer and then sync my phone to my computer... I do hate that also with the not syncing with the towers, but this is an acceptable replacement for me. This was always the way that I did it with my iPaq 1715 also.

Is there a way to display a very obvious reminder message when the date is obviously wrong? (It always thinks the date is 2006.)

endolith said:
Is there a way to sync the phone's clock to the cell phone network?
Click to expand...
Click to collapse
Hi endolith,
what ROM version are you at? I'm running a Win Mobile 6.1 ROM version and my Wizard is adjusting the time after a hard reste to the appropriate time and date automatically....
So maybe an update to a 6.1 ROM could help...
BTW: I'm using XIONS 0.7 ROM (but it is in German)
huibuh_1

Look in a registry editor for nitz
There should be two locations
HKLM\Software\OEM\PhoneSetting ShowNitzPage = 1 in DWord
HKLM\Drivers\BuiltIn\RIL NITZEnable = 1 in DWord
Those are the settings in my phone's registry.
Then start menu\settings\personal\phone you will now see a tab called Time Zones
Check the box to allow it to update the clock.
You may have to do the turn off phone wait 30 seconds and reset with pushpin routine.

HuiBuh_1 said:
what ROM version are you at? I'm running a Win Mobile 6.1 ROM version and my Wizard is adjusting the time after a hard reste to the appropriate time and date automatically....
Click to expand...
Click to collapse
Windows Mobile 6.1 Professional
CE OS 5.2.20273 (Build 20273.1.3.3)TNT
What program does it use to do that?
RoryB said:
Look in a registry editor for nitz
Click to expand...
Click to collapse
What's nitz?

RoryB said:
There should be two locations
HKLM\Software\OEM\PhoneSetting ShowNitzPage = 1 in DWord
HKLM\Drivers\BuiltIn\RIL NITZEnable = 1 in DWord
Click to expand...
Click to collapse
Mine says:
HKLM\Software\OEM\PhoneSetting ShowTimeZonesPage = 1
HKLM\Drivers\BuiltIn\RIL NITZEnable = 0
Changed NITZEnable to 1 and it seems to work. I wonder if that does the same thing as the check box under Time Zones?

endolith said:
Is there a way to display a very obvious reminder message when the date is obviously wrong? (It always thinks the date is 2006.)
Click to expand...
Click to collapse
Duh. Just set an appointment for the day it resets itself to, so it will pop up a reminder.
Also, I confirmed that NITZEnable toggles along with the UI checkbox, so you don't need to go into the registry at all.
Just go to Start > Settings > Personal > Phone > Time Zones and enable Automatic change time zone and clock. I mean, that's totally obvious, right? (I need to find a new phone that doesn't have any relationship with Microsoft...)

Just load TimeSync to your phone. It will require a data connection when used, but you can just run it manually. No need for all of this exotic flim-flammery...

Myrddin Wyllt said:
Just load TimeSync to your phone. It will require a data connection when used, but you can just run it manually. No need for all of this exotic flim-flammery...
Click to expand...
Click to collapse
Or just go to Start > Settings > Personal > Phone > Time Zones and enable Automatic change time zone and clock. No need to install anything, and no need for a data connection.

Related

registry keys

Hi Everyone:
A small clarification is needed. My device is defaulting to Moscow GMT+3 everytime I restart it. I want to know actually 3 things if possible:
1- What's the registry key that allows you to select the regional settings?
2- How can I know the table code of countries like Moscow is 0x00FFXXX, etc... for the various time zones.
3- I noticed sometimes that whatever registry keys in HKEY_LOCAL_MACHINE -> nls, they are changed everytime the system restarts. I was assuming that nls\overrides is doing that but I altered everyting and yet after restart new values appear in nls keys and even in overrides. Is there any other place in registry that writes values on top of nls upon restart?
appreciate the help,
Cheers
I have a similar problem where the backlight timeout setting (on battery power) resets to 10 seconds everytime I turn my MDA off. Really annoying.
I've tried changing the setting in the registry directly as well, but it still changes back.
Any ideas?
Thanks,
Scott
It is strange that something keeps changing the reg settings.
I had the 10 second thing on my Jamin and it seem to have something to do with the screen lock plugin.
Never did solve it.
Locale settings are in HKLM\nls DefaultLCID (dword) and you can find all possible values here.
But the time zone is set in HKLM\Time\TimeZoneInformation and its a bit complicated (its a whole data structure and not just a value)
I think you need to check your startup programs (HKLM\init and windows\startup).
levenum said:
It is strange that something keeps changing the reg settings.
I had the 10 second thing on my Jamin and it seem to have something to do with the screen lock plugin.
Never did solve it.
Locale settings are in HKLM\nls DefaultLCID (dword) and you can find all possible values here.
But the time zone is set in HKLM\Time\TimeZoneInformation and its a bit complicated (its a whole data structure and not just a value)
I think you need to check your startup programs (HKLM\init and windows\startup).
Click to expand...
Click to collapse
Thank you for your reply and for the great link. I am starting to feel that this problem is related to HTC Home. Appreciate if anyone can comment on this issue.
Requesting Moderators / Admin to move this post to the appropriate board
I've been playing with the new PDAMobiz ROM and discovered that in Settings->Phone there is an option to sync time with the cellular network.
Unfortunately this will also force your time zone in to what ever the network is set to which at least in my case is incorrect because the network operator did not want to bother with DLS settings.
Perhaps you have this setting on as well?

Tips & Tricks

Thought this might be a good place to start listing any quick tips and tricks you might have discovered.
To Lock Device quickly
Keep finger on the Red (Call End) button and it will bring up some options including keylock.
Not sure if anyone's noticed this but when I end a call on my Dual there is annoying little delay of about 3 seconds before the actual call is ended so I searched the registry and found this:
[HKEY_LOCAL_MACHINE\Software\HTC\PHONE\PhoneExtendSetting]
And I changed the value of EndCallTime from 3000 to 1000 re-booted and voila no more delays when ending calls
Hold the on/off button for soft reset.
Smart Dialing
This is an advertised feature but apparently not too many people are aware of it. Go to the phone app and start tapping the first couple of letters of the contacts name and the name matches will appear for you to choose from. I find this much easier than opening up the Contacts app and scrolling down to the name you need.
after pressing send for phoneapp u see last calls.
If u press left/right on the highlighted contact the phone switches through home/mobile/office...
HKLM\Software\HTC\Biotouch\Biotouch\ regulates the FPS of the cubeanimation.
Change "DownFPS", "LightFPS" und "UpFPS" to something higher for a smoother (and faster) animation.
Disable 3G, if not needed (it drains the battery faster than GSM):
Edit the registry key HKLM\Software\OEM\UMTS\OpMode and set it to "1"
Then also you could change that setting
Phone Settings --> Band --> Network Type --> GSM
To activate the changes, open the comm manager from the Cube, disable the phone and enable it again.
In italy with Vodafone I can't able to select also the Network Band GSM/UMTS to "GSM(900)" but I have to let it configured as "Auto" or "GSM(900+1800)+UMTS(2100)"
Bits
Ello, new here.. no idea if this helps a few Dual owners but..
Apps found to work on the touch dual:
S2u2 (iphone slide to unlock app), works like a charm:
http://forum.xda-developers.com/showthread.php?t=343256
HHC, HTC Home Customizer (name says it all), also working like a charm:
http://www.pocketemu.com/download4.html
gfreek, thnx for the EndCallTime key, works perfect and.. 1 less annoying feature to go
Things I'm still looking to solve:
1. Mp3 ringtone seems to fade out after picking up a call, for about 2/3 seconds the ringtone is still audible :S
2. Looking for settings for the Handsfree profile, i have an Lm959 bluetooth bracelet (how geeky, i know), works fine.. but only for calls, the device is capable of blinking the leds on receiving msgs, im looking for the settings to enable just that on the TD.
3. Polling frequency of the TD seems to be on the high side, f.e. it takes about 3 rings from someone before the TD starts "ringing", since voicemail kicks in @ ring 6 I miss a lot of calls.
I found a topic about just this problem with the touch(Elf) on sprint networks, with a quickcode (##7380# I think, well.. I'm not on sprint..so that doesnt work over here.. anyone with any clue would be welcome.. My current solution is disabling voicemail..)
ln1234 said:
To Lock Device quickly
Keep finger on the Red (Call End) button and it will bring up some options including keylock.
Click to expand...
Click to collapse
to do this quicker go to settings => long press end key
and select automatically execute and then lock device
holding the red button then locks the device in one press
You can invoke s2u2 instead normal devicelock
just install s2u2, rename Slide2Unlock.exe to EndKey.exe and copy all files to windows directory, with resco explorer.
the ilock doesnt seem to be working on my touch dual. when i try to go to settings, the screen goes blank.
You need to disable directdraw, do it via the registry as you can't access the settings.
raid said:
Disable 3G, if not needed (it drains the battery faster than GSM):
Edit the registry key HKLM\Software\OEM\UMTS\OpMode and set it to "1"
Then also you could change that setting
Phone Settings --> Band --> Network Type --> GSM
To activate the changes, open the comm manager from the Cube, disable the phone and enable it again.
In italy with Vodafone I can't able to select also the Network Band GSM/UMTS to "GSM(900)" but I have to let it configured as "Auto" or "GSM(900+1800)+UMTS(2100)"
Click to expand...
Click to collapse
Is there a way to add the "3G setting" directly in the Comm Manager as seen here : http://forum.xda-developers.com/showthread.php?t=354380 ?
GpsPasSion said:
Is there a way to add the "3G setting" directly in the Comm Manager as seen here : http://forum.xda-developers.com/showthread.php?t=354380 ?
Click to expand...
Click to collapse
Go with Total Commander to:
\\registry\HKLM\Software\HTC\CommManager and change the key
"SupportedFunctions" from 4 to 5
then make a new map named "5" (without the quotes)
go to that map and make a STRING named "default" and the string must
be "3G" (also without any quotes).
Then turn the phone off and on again and there is a 3G setting in your CommManager. I did not manage yet to add a icon in front of it
(and also not tested the working of the new setting)
Thanks, someone also pointed me to Schaps' app that has that setting http://forum.xda-developers.com/showthread.php?t=317070
GpsPasSion said:
Is there a way to add the "3G setting" directly in the Comm Manager as seen here : http://forum.xda-developers.com/showthread.php?t=354380 ?
Click to expand...
Click to collapse
Another way ...
Go to ... Start > Settings > Phone > GSM/UMTS Band , Set Network to "GSM" & Leave GSM to "Auto".
nightfear said:
Another way ...
Go to ... Start > Settings > Phone > GSM/UMTS Band , Set Network to "GSM" & Leave GSM to "Auto".
Click to expand...
Click to collapse
nice one..thanks
dapoldi said:
3. Polling frequency of the TD seems to be on the high side, f.e. it takes about 3 rings from someone before the TD starts "ringing", since voicemail kicks in @ ring 6 I miss a lot of calls.
I found a topic about just this problem with the touch(Elf) on sprint networks, with a quickcode (##7380# I think, well.. I'm not on sprint..so that doesnt work over here.. anyone with any clue would be welcome.. My current solution is disabling voicemail..)
Click to expand...
Click to collapse
that is driving me MAD at the moment. I'm missing almost all my calls.
Wish there was a way to change the amount of rings before voicemail kicks in.
please help someone!
Lord of the Badgers said:
that is driving me MAD at the moment. I'm missing almost all my calls.
Wish there was a way to change the amount of rings before voicemail kicks in.
please help someone!
Click to expand...
Click to collapse
ah found it, at least for UK Orange people:
Please bear in mind that the following code is only valid for phones on the Orange UK network.
The code to set the length of time your phone rings is:
**61*07973100123*11*??#
Where ?? is the time in seconds, e.g. to set the ring time to 30 seconds you would type the following code at the standby screen then press the green send button:
**61*07973100123*11*30#
To make your phone ring for only 10 seconds:
**61*07973100123*11*10#
The code works in 5 second intervals, i.e. you can set 5, 10, 15, 20, 25 & 30 seconds.
Click to expand...
Click to collapse
works fine. thank god.
Lord of the Badgers said:
that is driving me MAD at the moment. I'm missing almost all my calls.
Wish there was a way to change the amount of rings before voicemail kicks in.
please help someone!
Click to expand...
Click to collapse
go to the phone application
Settings->Services->call forwarding
Set the time to what you want
Arnon

Speaking Clock with Chime & Signal Strength detector

## TamerSpClock v1.4 ##
Last update 13 Dec 2008
"TamerSpClock" is a Windows Mobile 2003/5/6 software which lets you take hand over your time to the max. It is a fully customizable speaking clock & a chimer.
- you can choose a THEME of time intervals of 1 ,5 ,15 ,30 or 60 minutes ,Then you can choose actions to be done on these choosen theme intervals.
- you can adjust when to speak time or chime and when to mute in a way that differs from other programs by means that you can set multi portions (intervals) of time that mute the program automatically for daily use. you can access the file "Validity.ini" found in the folder named "settings" inside the program installation path. this file can be edited by any notepad or word (pocket or pc word) then you can specify at what hours to work on and what to mute (just Change validity = 0 corresponding to hours that needed to be muted & Change validity = 1 to the rest of the hours).
- The program can wake up the device without waking up your screen conserving your battery life and will chime even if the ppc is sleeping or in a deep sleep, The software have a feature that can force the screen not to wakeup (BlackMe feature) at chiming times or (if you choose to) to leave it to the current windows mobile configurations (settings) to decide ,this is useful for some ppc that wakeup the display on every chime which may have negative results on battery life.
- you can put your own wav files to be chimed ,just insert them in folder "Wav" found inside installation directory but use the same names of course.
- This software differs from other similar products in that if you choose for example 15 minute iterval for speaking the clock ,it wll activate itself and speak time on whole miute numbers like 15-30-45-60 and will not just repeat the choosen interval starting from the time you switched it on which results in speaking times like 4:52 and 7:27 etc.
- you can choose or omit salutations like "the time is" & "Am ,Pm" & saying "Oclock" at the whole number hours. this can be customized using the provided links to enable and disable the action features.
- you can choose whether to use vibration or no with the chiming process.
- you can stop all software processing events by one finger click.
- Software will automaticaly activate itself and work again after any restart of the device.
- you can set an action like signal check to work with Themes (feature to check signal strength every x time) if the signal drops ,it will announce you with an alarm ,this feature only works if the phone is on and the signal is less than 40%.
- you can set an action like Zekr which can help Muslims remember their Lord every 5 minutes with a low volume sound saying God is the most Great. This option acts solely without dependency of the choosen theme interval since it have a fixed firing every 5 minutes (take it or leave it).
# How to install Cab file of TamerSpClock:
1- For versions prior to v1.4 you must download MortScript from the following link
(Version v1.4 & above already have it embedded inside software)
http://www.sto-helit.de/index.php?mo...=view&entry=65
This software acts like an environment for "TamerSpClock" to work. please note that "TamerSpClock" cannot run without installing this software.
2- Transfer cab to any place on your ppc using active sync or any other communicating software.
3- Choose whether to install to Device or to MemoryCard ,It is very important to choose the installation target location during the setup process corresponding to the version you downloaded whether it is on memory card or on phone. Note that program is hard coded ,this is why this point is very important for the program to work.
4-For Version v1.4 & above before running program ,press the icon named "RunFirst" prior to run the program (This acts as if MortScript Cab is installed)
This software had been tested on HTC Tytn & found stable ,Also can work on any windows mobile device.
I have been looking for an hourly chimer that does not wake up the screen. The disappointing thing about this one it it is hard coded to run from the storage card. Can this be modified to use variable paths?
One issue I have with installing to the storage card is Windows Mobile unmounts the card to save power on some devices. I also change my card based on what I am doing. I keep my maps on one card and my MP3s on another.
painter_ said:
I have been looking for an hourly chimer that does not wake up the screen. The disappointing thing about this one it it is hard coded to run from the storage card. Can this be modified to use variable paths?
One issue I have with installing to the storage card is Windows Mobile unmounts the card to save power on some devices. I also change my card based on what I am doing. I keep my maps on one card and my MP3s on another.
Click to expand...
Click to collapse
Added 2 versions ,one if you want to setup on the Phone Main Memory & the other for Storage Card.
This really sounds great - but how to use it?
I am no expert in programming or in mort scripting.......
I would like to use this feature: "you can set an action like signal check to work with Themes (feature to check signal strength every x time) if the signal drops ,it will announce you with an alarm ,this feature only works if the phone is on and the signal is less than 40%."
But no speaking clock, only those alert, when signal drops.
It should check every minute.
What do I have to enable/disable for that?
And how to let it run, when my touch is sleeping?
Thanks!
I'm using a TyTN II. Great software.
Like to feedback that when I was using my bluetooth headset, when the phone is off (no display), announcing (audio) could be heard and vibration. When I don't use the bluetooth headset (bluetooth is off), and phone is off (no display), I don't hear any announcement and there is vibration only. If I turn on the phone now, I will hear the end part of the time announcement.
Is this normal?
Thanks.
zard said:
I'm using a TyTN II. Great software.
Like to feedback that when I was using my bluetooth headset, when the phone is off (no display), announcing (audio) could be heard and vibration. When I don't use the bluetooth headset (bluetooth is off), and phone is off (no display), I don't hear any announcement and there is vibration only. If I turn on the phone now, I will hear the end part of the time announcement.
Is this normal?
Thanks.
Click to expand...
Click to collapse
Zard .. if you enable the black me feature the speaking clock can be capable of walking up the device to say time at chosen theme points without walking up the screen. So i advice you to enable the blackme feature as long as the phone is in your pocket. if you are using the phone for an instance or a period of time you can disable the blackme feature since when you are using the phone the feature will be annoying.
in some devices (devices differ in reaction to wakeup) the phone cannot wake up to say the time if it is sleeping ,this is why i made the blackme feature. So the solution is to enable it.
Also if you go to programs menu in the start button you will see a pack on enable & diable features. you can choose what ever you like to enable and what to diable.this features can be clicked (enabled or disabled) & once confirmed you will notice that it will be active wherever any theme is choosen. iam sure that the blackme feature is able to walking up the device to say the time whether your device is in sleep or deep sleep.
kino-kino said:
This really sounds great - but how to use it?
I am no expert in programming or in mort scripting.......
I would like to use this feature: "you can set an action like signal check to work with Themes (feature to check signal strength every x time) if the signal drops ,it will announce you with an alarm ,this feature only works if the phone is on and the signal is less than 40%."
But no speaking clock, only those alert, when signal drops.
It should check every minute.
What do I have to enable/disable for that?
And how to let it run, when my touch is sleeping?
Thanks!
Click to expand...
Click to collapse
Kino-Kino .. first of all open the start menu programs ,you will find 2 folders ,one is named enable & the other named disable. now you are ready to open each and click what ever features you like to be enabled and whatever to be disabled.
At this time you are ready to go for the Theme selection which means at what intervals you want the choosen features to fire ,you can try the "01M" which means that the software will fire every 1 minute to execute the selected feature (or features if you choose others).
For example ,if you want only the signal detection feature ,go to disable folder and click all features to disable them all ,then go to enable and only click the shortcut named "Signal".
Once done .. every 1 minutes (since we choosed "01M") the phone will execute the selected feature (or features). in some phones the system cannot walkeup itself to execute the so called notification tasks at given times if it was in "Sleep" or "Deep Sleep Mode". So you can check your phone reaction to such notification tasks.
To make sure we are ready to go ,you must check first that your phone registry key when the phone is on and receiving signal looks like this :
[HKEY_LOCAL_MACHINE\System\State\Phone] the value of "Cellular System Available" must be 65
to do this test just download Fred Taskmanager free from this link
http://www.dotfred.net/TaskMgr.htm
once downloaded install it ,open it and go to RegEdit tab and go to [HKEY_LOCAL_MACHINE\System\State\Phone] & check for "Cellular System Available" number .. it must be (65) i mean the number between brackets.
If this is the case ,the program will correctly do the job. but if it isnt (may vary from phone to another) ,then this number must be modified in the software to read correctly ,Go to program installation folder " \Program Files\TamerSpClock\Data\Signal.mscr " rename the file "Signal.mscr" to "Signal.txt" then open it by any notepad or word ,then check the line "if(%PhoneActive% = 65)" and change the 65 to be like the number that you found for your phone in the normal signal state. Do not forget to rename it back once finished to "Signal.mscr".
Thanks
Thanks going to test on my lovly hima.
Thank You for Your reply!
I think, there could be a problem:
The reg key, You mentoned, does have different values.
If I am connected to a "GPRS" network, it is "1".
If I am connected to an "EDGE" network, it is "8".
And if only phone is active, but no internet-connection, it is "1".
So what should I take?
Thank You!
EDIT: There is another key called "Radio ready state" with the value "31".
And all value are "0" when radio is off.
kino-kino said:
Thank You for Your reply!
I think, there could be a problem:
The reg key, You mentoned, does have different values.
If I am connected to a "GPRS" network, it is "1".
If I am connected to an "EDGE" network, it is "8".
And if only phone is active, but no internet-connection, it is "1".
So what should I take?
Thank You!
EDIT: There is another key called "Radio ready state" with the value "31".
And all value are "0" when radio is off.
Click to expand...
Click to collapse
The reply is that you take the number between brackets on the idle state without conecting to any network ,because the idea as you can see from the code that there is 2 conditions must be fullfilled to fire the signal alarm which is 1- if the signal in the idle state be so and so and 2- in the same time signal drops to so and so ... Bingo ... fire
So ,now you got the idea of the code & can now modify it to fullfils your needs ,and you are ready to put your constants that reflects the state where you want spclock to fire. wishing this could help .....
timoz73 said:
Zard .. if you enable the black me feature the speaking clock can be capable of walking up the device to say time at chosen theme points without walking up the screen. So i advice you to enable the blackme feature as long as the phone is in your pocket. if you are using the phone for an instance or a period of time you can disable the blackme feature since when you are using the phone the feature will be annoying.
in some devices (devices differ in reaction to wakeup) the phone cannot wake up to say the time if it is sleeping ,this is why i made the blackme feature. So the solution is to enable it.
Also if you go to programs menu in the start button you will see a pack on enable & diable features. you can choose what ever you like to enable and what to diable.this features can be clicked (enabled or disabled) & once confirmed you will notice that it will be active wherever any theme is choosen. iam sure that the blackme feature is able to walking up the device to say the time whether your device is in sleep or deep sleep.
Click to expand...
Click to collapse
Thanks, with Blackme, it works now.
dont work with my diamond
great sharing.
thanx.
Dynomite232 said:
dont work with my diamond
Click to expand...
Click to collapse
Dynomite232 ,Kindly feedback whether the mortscript program didnt run on diamond or the TamerSpClock itself. i didnt expect this to happen from the Diamond of a VGA screen since my software didnt realy have a User Interface Menu ,its only shortcuts. In addition that Mort do support any windows mobile device.
Thanks again helping me, I think, I start to understand what Your mortscripts are able to do!
But I have to ask once more:
So I have three different scenarios, when I would get that signal-alert:
1 If Cellular Systam Available is "8" AND signal drops to less than 40%
and
2 If Cellular System Available is "1" AND signal drops to less than 40%
and
3 If Cellular System Available is "0" WITHOUT checking the signal strength
So would it be possible to edit the Mortscript this way?
Thank You!!
Reply to Kino-Kino
kino-kino said:
Thanks again helping me, I think, I start to understand what Your mortscripts are able to do!
But I have to ask once more:
So I have three different scenarios, when I would get that signal-alert:
1 If Cellular Systam Available is "8" AND signal drops to less than 40%
and
2 If Cellular System Available is "1" AND signal drops to less than 40%
and
3 If Cellular System Available is "0" WITHOUT checking the signal strength
So would it be possible to edit the Mortscript this way?
Thank You!!
Click to expand...
Click to collapse
Kinio-Kino for your described situation the case will be as follows (copy & paste what is below between the # signs to replace what is inside Signal.mscr ,you can find this file inside a folder called Data inside the program folder inside Program Files)
###################################################################
ErrorLevel ("syntax")
SignalStrength = RegRead("HKLM", "System\State\Phone", "Signal Strength" )
PhoneActive = RegRead("HKLM", "System\State\Phone", "Cellular System Available" )
if(%PhoneActive% = 0)
PlaySound "\Storage Card\Program Files\TamerSpClock\Wav\Signal.wav"
endif
if(%PhoneActive% = 8)
if (%SignalStrength% < 40 )
PlaySound "\Storage Card\Program Files\TamerSpClock\Wav\Signal.wav"
endif
endif
if(%PhoneActive% = 1)
if (%SignalStrength% < 40 )
PlaySound "\Storage Card\Program Files\TamerSpClock\Wav\Signal.wav"
endif
endif
###################################################################
You can now Download the latest version v1.03 ,I build a new user interface for this software instead of the icons .Before Uninstalling Do the process of "StopingAll" feature then make a new Install to v1.03.
.
Hi,
first, thank You again, its working now as expected, great!!
The new Version 1.3: Both cabs get installed to the main memory, maybe something went wrong with one of them?
And one more question:
When my phone is sleeping, I dont get those signal-alerts.
So You have Your blackme-feature:
How could I handle that, to get the hardware-buttons locked, when blackme is active? I have a HTC Touch.
Thank You!
kino-kino said:
Hi,
first, thank You again, its working now as expected, great!!
The new Version 1.3: Both cabs get installed to the main memory, maybe something went wrong with one of them?
And one more question:
When my phone is sleeping, I dont get those signal-alerts.
So You have Your blackme-feature:
How could I handle that, to get the hardware-buttons locked, when blackme is active? I have a HTC Touch.
Thank You!
Click to expand...
Click to collapse
kino-kino ,Welcome again & thank you for your feedback. The Cab file targeting the storage card have been updated in the main thread page.
you are asking now about 2 subjects ,the first one concerning the signal alert didnt fire during deep sleep of the phone ,i think you might try to make the speaking clock feature active along with the signal alert feature ,maybe it will wakeup your device to fire at the specified times, of course if its voice is annoying to you can try deleting the clock wav files but leave of course the signal.wav without deleting. I wonder this happens to you although my Htc Tytn wakeup and fire Signal Alerts at specified times.
The second question can be solved simply by downloading "HomeScreenPluPlus" from the following link:
http://www.chi-tai.info/cs_batterystatus_xda_neo_wm5_im_cs.htm#Download
This software is free and have a feature in the second UI page of options that lock your device when the screen is off and vice versa ,see this pic for explanation.
Thanks for your great app, but I have troubles with BlackMe feature. If this feature is disable, my phone doesn't speak, vibrate only. But if it's enable, it turn off the phone screen when speaking time. That's annoy when I'm doing something on my phone, especially while downloading a large file, it interrupts the wifi connection and I have to re-download from beginning. Any solution for that?
hung_ng said:
Thanks for your great app, but I have troubles with BlackMe feature. If this feature is disable, my phone doesn't speak, vibrate only. But if it's enable, it turn off the phone screen when speaking time. That's annoy when I'm doing something on my phone, especially while downloading a large file, it interrupts the wifi connection and I have to re-download from beginning. Any solution for that?
Click to expand...
Click to collapse
yes i know hung_ng ,i made the blackme feature as a separate item in folder links so that you can assign its icon to a hardware button to be easily accessed so that when you are using your phone you can easily deactivate BlackMe.
This annoying feature (from my point of view as you eaxactly) is essential in many phones ,as the system cannot wakeup the device from a deep sleep to do the choosed actions. the blackme feature (also known as "ToggleDisplay=1") force the phone to wakeup to fire the action. if it is disabled many devices will fall in deepsleep without being able to wakeup. the last version 1.3 have this separate shortcut that i explained.
Another idea i made in my Tytn and made me feel comfortable is that i made my telephone sense when a specific window is open ,the blackme is disabled automatically and when i close this window it reverts automatically to be enabled. for example i made RescoExplorer2007 window when it is opened the blackme is disabled & serving me while i work ,and once i finish i close Resco and automatically blackme returns active and conserving my battery life.
Sorry for being long in my explanation but if you are interested in the idea ,i can make a version for you that is capable of deactivating BlackMe once a specific window is opened. i am not a programer ,i am an Architectural Engineer that once upon a time needed this software and didnt find a really satisfying one available all over the internet ,so i decided to learn Mort Script and i write a one satisfiying my needs and by the way i think that it might help other people who might need it as me.

timezone cannot be set correctly

Hi all,
I have at last found a deception point with my blackstone
I have a problem with the timezone. I set it to (+1) Paris, Madrid. All is well, and my appointments after the 29th of March (summertime date) are OK.
If I reset my blackstone, or simply wait for the next day, then the time zone is back to (+1) Prague (first zone for +1 zone), and then all my appointments after the 29th of March are not correct (one hour before). I think that Prague does not include summmertime...
I have tried several tips (including trying to use "Other town" in alarm&Clock setting), but no result.
any idea ?
thanks in advance !
Blg
Are you sure that this is happening automatically? As far as I know it is iGo8 (R1), which is responsible for that, so just disable the automatic time zone correction in iGo8 (if it is the case for you).
Thanks for your answer.
well, it seems it is automatic, I have not used Igo8 for a long time :-(
The evening, I set (+1) Paris, and the next morning, (+1) Prague is back !
I have just disable Igo automatic zone correction in Igo, and it does not correct the problem : after a reset, Prague is back again :-((((
And Igo does not seem to stay on the timezone I have set : it returns on the first +1 timezone (Amsterdam).
blg said:
Thanks for your answer.
well, it seems it is automatic, I have not used Igo8 for a long time :-(
The evening, I set (+1) Paris, and the next morning, (+1) Prague is back !
I have just disable Igo automatic zone correction in Igo, and it does not correct the problem : after a reset, Prague is back again :-((((
And Igo does not seem to stay on the timezone I have set : it returns on the first +1 timezone (Amsterdam).
Click to expand...
Click to collapse
If you are starting Igo, this is an issue with Igo - one of the versions changed the timezones even if you asked it not to. Update to the most recent version.
"Autocorrectie" & "Tijdzone automatisch inst." disabled.
After a restart of IGO the 'prague' settings are back.
Tought I have the latest version of Igo....
I have seen that this seems to take place in the registry :
The HKEY_LOCAL_MACHINE\Time\TimeZoneInformation is resetted (almost all bytes to 0).
Even Prague is no more in this key (there is a difference in this key if you set Prague or if you reset the HD and Prague is set automatically).
very strange.....
Could be Activesync fudging around with the settings when you connect to the PC? I had this problem on my Elf for a while but for some reason it suddenly started working OK again.
timezone cannot be set correctly. solution?
Changing the timezone settings through the IGo GUI won't work, dunno why. But , fooling around some other forums, i found this other solution that seems to work, at least for me (igo 8.3.2.1).
You just have to add these following 3 lines to the "sys.txt" configuration file that is in the application directory under the programs folder on your device (es. /Program Files/iGO8/). Hope this works for you too.
------------------------------------ cut here-----------------
[timezone]
sync_os_timezone=0
reset_os_timezone=0
------------------------------------ cut here-----------------
I do not use Igo, so this will not work for me.
I have same problem. I set GMT+2 Helsinki Riga and when I made softreset, there's GMT+2 Windhoek. Windhoek isn't first on list so no just exactly same problem, but it keeps changing whatever I do.
it seems that a hard reset has resolved the problem on my Touch HD.
I am going to re-install the softwares one by one and check each time, in case of...
Hi,
Seems to be fixed now.
I don't think it has anything to do with IGO.
Touch the clock -> settings screen opens.
Select/enable the 'visiting' mode/selection.
Set the proper GMT value within the visiting mode.
Close the 'settings' screen by selecting 'ok' in top right corner.
Touch the clock -> settings screen opens.
Select/enable the 'Home' mode/selection.
Set the proper GMT value within the visiting mode if needed.
Close the 'settings' screen by selecting 'ok' in top right corner.
That did the trick for me.
Still wondering if it's running on the visiting mode in the background, or what the heck caused this... but it's working oke now.
you're right, this procedure works for me... during some time...
The next day, the problem was there again...
No more problem since the hard reset.
Olaviman said:
I have same problem. I set GMT+2 Helsinki Riga and when I made softreset, there's GMT+2 Windhoek. Windhoek isn't first on list so no just exactly same problem, but it keeps changing whatever I do.
Click to expand...
Click to collapse
I have exactly same problem what you have. No matter which rom i use, every time I got this same result that HD is swiching this time zone from GMT+2 Helsinki Riga to GMT+2 Windhoek.
Try disabling 'Automatic change time zone and clock' under 'Settings' 'Phone' to see if that works. Sometimes Networks give out incorrect timzone data and it corrupts the reg key.
Farsquidge said:
Try disabling 'Automatic change time zone and clock' under 'Settings' 'Phone' to see if that works. Sometimes Networks give out incorrect timzone data and it corrupts the reg key.
Click to expand...
Click to collapse
Yes that did the trick. Thanks.
cxar71 said:
Changing the timezone settings through the IGo GUI won't work, dunno why. But , fooling around some other forums, i found this other solution that seems to work, at least for me (igo 8.3.2.1).
You just have to add these following 3 lines to the "sys.txt" configuration file that is in the application directory under the programs folder on your device (es. /Program Files/iGO8/). Hope this works for you too.
------------------------------------ cut here-----------------
[timezone]
sync_os_timezone=0
reset_os_timezone=0
------------------------------------ cut here-----------------
Click to expand...
Click to collapse
Hi,
I have a similar problem, but this doesn't solve my problem.
The only difference is that I installed iGo on my SD card, and I don't have any iGo folder in Program files.
Same thing happens with GMT+8. I select Perth (GMT+8) then ActiveSync decides that it should be reset to the first timezone in the list (Beijing, HK).
I have disabled 'Automatically set Timezone' in the Phone settings and the Timezone is correct on the PC.
Something must have changed because it used to select GMT+8 Ulaanbaatar before (which is last in the GMT+8 list)

device auto lock and off when i want use Garmin

hi all
i want to use garmin for 30 min or much but after 1 min my device lights goes off and then display off and lock what can i do for disable auto device lock and auto off after 1 min
BR
weird, i don't have that problem.. try configuring your GMXT, go to settings --> display --> backlight override and check all boxes..
p/s: if u wanna enable auto rotate so that u could view the maps in widescreen mode, add these codes to your registry..
for hkcu\software\htc\htcsensor\gsensor\modulename, add registry value "Garmin Mobile XT" = "\Garmin\Que.exe"
for hkcu\software\htc\htcsensor\gsensor\WhiteList, add registry value "Garmin Mobile XT" = "QUE_SUBAPP_WND_CLASS"
Garmin in landscape
Hi, thanks for the tip!
I always wanted to see GMXT in landscape, but didn't know how to do it.
I have copy/pasted values to the suggested locations, but nothing happened.
The registry values I have created are string values. Should I try with e.g. dword, or something else?
TNX
hi man i check all boxe in setting -> display -> backlight but after one minute my device goes to lock stat and after that my display goes off .
i want registry address for time of suspend mode for device to lock and change it to example 20 min
BR
Maybe you should check only the first one that says "always on".
CRO_Misho said:
Hi, thanks for the tip!
I always wanted to see GMXT in landscape, but didn't know how to do it.
I have copy/pasted values to the suggested locations, but nothing happened.
The registry values I have created are string values. Should I try with e.g. dword, or something else?
TNX
Click to expand...
Click to collapse
u are right all the way, except that u need to soft reset the phone for it to take effect..
amirjco4 said:
hi man i check all boxe in setting -> display -> backlight but after one minute my device goes to lock stat and after that my display goes off .
i want registry address for time of suspend mode for device to lock and change it to example 20 min
BR
Click to expand...
Click to collapse
have u tried re-installing the GMXT..?
non of your help is useful we need registry value change for that
I'm having the same problem. Garmin worked perfectly for the last 2 months up until last week. now it locks automatically (but you still have to press the unlock button to be able to slide across the tab) and it loses satellite reception for a second. To avoid it I have to, say zoom in or out on the map, every 50 seconds otherwise it locks after it reaches a minute.
Has anyone found a solution or is it just a case of reinstalling it?
Sorry to revive this thread but I also have this problem. "Backlight Override" is checked but still have the lock come on after a minute or so. Really annoying. I also try reinstalling but no help.
Could this have something to do with CHT editor's lockscreen? or BSB tweak's setting? Just a thought. I have been using Android mostly so haven't got time to test out all the setting to see if it will make any difference.
as a work around, can you just change your backlight settings when you need to use garmin?

Categories

Resources