Related
I use my 8525 in a side case and when the phone rings I usually pull out the phone to see who's calling to decide if i want to answer... though 9 out of 10 times i accidentally hit the answer button. I always lock my phone via device lock on today screen... is there a reg hack or setting which will allow me to disable or customize ALL the buttons (when in lock mode) on the 8525 so I don't accidentally answer. to me if i were to assign a button (ie power or ptt) to only be allowed to accept a call (when the phone is in lock mode) that'd be great. I'm tired of auto answering and what good does a device lock do if you can easily auto answer?
bumping this back up... Can I be the only one with this issue? If so how do you use your phone and not auto answer?
abricko said:
bumping this back up... Can I be the only one with this issue? If so how do you use your phone and not auto answer?
Click to expand...
Click to collapse
Sorry you're not getting replies and I have no solution of the type you are looking for sadly. I've tried to replicate what you say happens but it's not easy!!! My key is not that easily pressed and I always put the device back with screen towards my body - my fingers don't seem to get very close to the green button.
This is probably daft to suggest but have you checked the setting that lets you specify auto answer within X number of rings - just in case it's answering the call by itself!!. (apologies if you checked this setting already!!)
Mike
This may do what you want...
http://www.pocketmax.net/smf/index.php?PHPSESSID=da5459e6aadc9c38d5a74b0276782091&board=19.0
Auto Answer is not set... the problem is (and it's a problem with the phone design) when the phone is locked none of the buttons respond until you hit the power button and then unlock the phone via the screen (which is good).
However when there is an incoming call or reminder the screen turns on and then a few buttons are active on the phone (send, end and the two soft keys seem to be). So when a phone call comes in, if the phone is in your pocket or the hip case while reaching for the phone it's VERY easy to accidentally press any of the active buttons and then accidentally accept or reject that call.
I've searched everywhere I can think of and I find little mention of this problem and no mention of a fix, most screen lock replacements only do as much locking as the WM5 built in lock does. The button re-activation after an incoming call is probably something built into the hardware. That's all I can deduce from this.
Thanks for the responses I've received so far.
I am on my fourth PDA phone and have used both Win Mobile 2003 and WM5. They all behaved this way and it is one of my biggest complaints with the Windows OS. I have seen apps for Palm that solve the problem. How hard could it be to have the option to only wake with the press of the power button?!
not hard at all, but the again its M$, i am surprised these devices to have ctrl-alt-del keys.
Anybody know if there's a way of keeping my Trinity in standby even when a text message comes through - I keep the thing in my pocket and if I don't look at it straight away after a text has come through, all kind of things happen - programs get launched, photos get taken, voice memos are created, just from it moving around in my pocket after un-standbying itself!??
Thanks
Lock the screen and when a text comes no programs will launch!
Nope...
Doesn't work...as soon as a text comes through, everything unlocks - is there anyway to stop this from automatically happening?
Thanks
flight mode
tjw2007 said:
Doesn't work...as soon as a text comes through, everything unlocks - is there anyway to stop this from automatically happening?
Thanks
Click to expand...
Click to collapse
Not so on mine when it is locked it stayes locked! The screen will come on but the machine stays locked.
What mine is doing is when a text comes through, it seems to be causing the device to unlock, because the screen will take touch commands - I need to be able to lock the screen and get it to stay locked even when a text comes through. Any experts out there who might know how to achieve this?
Thanks
What is flight mode anyway?
OK, let me put this another way - is it possible to lock the screen until you press the standby button, so that nothing else unlocks it such as a text message or phonecall?
Thanks
I don't have this problem. My screen is set to go off after 1 minute. When the phone is in standby, all I get is a tone and the orange light flashes. The screen will not come on, unless I press the power button.
No input is accepted when in standby by the screen or any button except the power button - check your settings
I also have it set to auto-lock after 2 hours, so even if I get a text, and turn the screen on, then i need to put the password in before the screen unlocks
i use my m700 the same as you with no problems
RESOLVED!
Managed to put the device lock option on the 'Today' screen and this keeps the whole device locked (screen & all) no matter what happens, until you press the unlock option on the screen. Hooray!
So, I have PocketShield installed and it's set to slide or light unlock and answer. Quite often when I get a call it takes so long to unlock and answer, the person is gone...
There are maybe a few options -
1) I've installed and uninstalled so much stuff, maybe I need to start fresh? I have noticed the HD is a little 'laggy' now. Should I hard reset and install things back on slowely, testing it's responsiveness as I go?
2) Maybe I should switch to S2U2? I used this for a long time on my Kaiser, but have been concerned by everyone saying it drains battery power.
3) Do I need a screen lock program? The device only wakes up on a phone call and now you have a slide to answer/ignore anyway. Do the hardware keys do anything at this point? Am I safe to carry it round in my case without a screen lock?
Does anyone else suffer from this, or just me?
Thanks for any help/advice in advance.
Having the same issue. Sometimes my slide option simply doesn't work first few attempts. My solution is to use the "answer call" key beneath the main screen until this gets resolved.
S2U2 works like a charm on the HD and it doesn't draw additional battery as far as I have seen over the past few days.
When u have a call, u don't need to slide so you unlock the device then accept/reject the call.
Depends on what you have set, you can either have the original accepting/rejecting HTC screen poping up to take/reject your calls,
or you can set it so u have a new slider appearing on the wallpaper of S2U2 to accept/reject the calls
Try it, you won't regret it guys.
Well, yesterday I hard reset my HD and installed just the stuff I wanted. I've gone back to S2U2 and everything seems much much better so far. The only annoying thing is sometimes the phone wakes in landscape mode still, even though it's set to not rotate in Gyrator (and doesn't when it's woken, it stays in whatever it is in.)
Whats the difference between S2U2 and the phones default slide to answer phone ?
In other words, why install S2U2?
Its a very well presented Screen Lock, that's why. The question is just how to go from that to answering a call...
Id I have S2U2 installed, and a call comes in on my HD, what happens? does s2u2 take over from the default "slide to answer" system?
Yes it does. I think the problem I had was it wasn't doing that properly before hand. They were obviously conflicting with each other and I was struggling to answer calls.
gt112 said:
Whats the difference between S2U2 and the phones default slide to answer phone ?
In other words, why install S2U2?
Click to expand...
Click to collapse
Well S2U2 will lock your phone screen and buttons so you do not start by mistake an application or a phone call when the device is in your pocket.
Even if by mistake u click on the power on button, ur device is still locked until u unlock it using a slider like on the i-phone.
It allows u to display a wallpaper of your choice, different then the one on your today screen or in TF3D. It allows u to display clock date, network signal, tasks, missed calls, SMS, etc ...
Try it, it's free and very nicely designed
I tried to use S2U2 and found that just like every other locker it is behaving wrongly after a call - it leaves the device unlocked! So if I listen to music and get a phone call I'll have to pull it out of the pocket to lock again. There is a silly option to lock after each call of course, but this is just stupid - I just want the device to stay locked until I unlock it - how difficult is this?
Funnily, the only locker behaving properly is the stock Windows one, but it has a backlight bug and switches the device to Home screen.
It's just amazing how nobody can do such a basic function right.
vangrieg said:
I tried to use S2U2 and found that just like every other locker it is behaving wrongly after a call - it leaves the device unlocked! So if I listen to music and get a phone call I'll have to pull it out of the pocket to lock again. There is a silly option to lock after each call of course, but this is just stupid - I just want the device to stay locked until I unlock it - how difficult is this?
Funnily, the only locker behaving properly is the stock Windows one, but it has a backlight bug and switches the device to Home screen.
It's just amazing how nobody can do such a basic function right.
Click to expand...
Click to collapse
Just tried it few seconds before posting, called myself from the office phone, answered the call using the slider is S2U2, the screen turned off, I ended the call by pressing on the end call button on my HTC touch HD, and the S2U2 screen lock was there, the device was still locked.
It works perfectly with the touch HD.
After i hang up on a call (when the phone is in sleep mode and the screen is locked) the screen unlocks. this is quite contrary to what is mentioned in the phone manual chapter 1 page 45. this becomes an issue since i use a bluetooth headset and the phone remains in its sleeve/case and after every call, a whole bunch of applications will launch since the case is in contact with the screen. have i overlooked some settings or are there other owners who have faced this issue?
ideas and suggestions welcomed
did you check it out if any of the hardware buttons being pressed against the case hence wakening up the phone.?
i had it to only closed al my apps in taskm and it stoped flickering
My HD2 is also behaving in the same way even in controlled test conditions - the phone unlocks when a call comes in (I'm presented with slide to accept or reject call) The phone unlocks during the call, but fails to lock again on disconnect (either by pressing "end call" or hang up via bluetooth).
Can anyone verify this? Is it interacting with something I installed?
I believe I found a (complicated) workaround.
What I want: leave HD2 inside pocket, answer calls with bluetooth headset, hang up and phone will go back to lock.
Problem: After I hang up using bluetooth or press the big red "End Call" button or the other party hangs up, the phone stays unlocked! It stays powered on and all kinds of buttons gets clicked.
Practically all lock sw uses their own lock screen (which I don't want to install). CSDevCtrl does not trigger by phone. TouchLockPro uses its own transparent lock screen but can respond to phone events. Using the !SUSPEND for TAPI\Ended under settings does not seem to work when the screen dims about 50 secs into the call.
Solution: Use TouchLockPro together with LockAndOff. Get TAPI\Ended to run LockAndOff will turn phone off, whether by bluetooth, big red "End Call" button, or the other party hangs up.
BTW: I think there is some confusion on whether the phone locks when you
1. press the big red "End Call" button, or
2. the hard "End call" button
in the forums.
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
linivan said:
I noticed that HD2 have a light sensor next to the top ear speaker.
During a call, if the phone is put near the ear and cover the light sensor , the screen become non-active which is good.
If anyone can come up with a lock sceen using this light sensor , then the problem with random launch of program when phone inside pocket will be solved.
This lock screen should only activated right after an end of call, beacuse , sometime you may want to use the phone in a dark place.
Click to expand...
Click to collapse
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
johncmolyneux said:
It's the proximity sensor that turns the screen on and off during a call, not the light sensor. How else would it work in the dark? (which it does)
Click to expand...
Click to collapse
My proximity sensor does not work, when I am getting a call my screen turn off and when I am taking the phone out from my face it turn on only when I am out side at the sun!! the screen stay off when I am inside room. I tested it with flsh light and it is working also.
I have a T-Mobile US version of the HD2. I am having the same problem when using the bluetooth system in my car. After answering or making a call the phone stay unlocked. And then starts making random calls while I am driving!!!!
There has got to be an easy fix for this!!!
Buy pocketshield, problem solved.
i have this unlock problem with 1.48 rom and i solve it by pressing start button and lock. after that everything works fine unless i change theme in settings. then just repeat first step.
Solved
Same trouble with me until I use the following software. I tried it and it's almost perfect. unzip it and just copy to your HD2, run CallerLoc.exe and click Yes, you'll find:when you hang up, or he/she hang up a call, or a call is established, the screen will turn off.
Why say 'almost perfect', the software is in chinese, but the filename is in english. and it's a call location software but with the function we need.
To stop or before you delete the software, run Callerloc.exe and click Yes again.
Hope this will help you. Sorry I don't find a English version of this software. I esure and I'm using this software perfectlly with my Leo.
theciscokid said:
Buy pocketshield, problem solved.
Click to expand...
Click to collapse
Same for me
Greetings.
I understand this is quite an old thread I'm digging up but I need a little help as well and I didn't want to start a new topic just for that.
I've this silly problem, appeared right out of the blue:
You all know the standard manila behavior, when the phone is idle, the screen first dims and after some more time, depending on your preferences, the screen locks. It also locks if you press the power off button. This all was happening to me till this morning.
I added an event in the calendar (the only change I made today) and after that, my phone dims and then goes in sleep mode after the designated period of time, but DOESN'T lock!!! It doesn't even lock when I press the power off button. I can still lock it by pressing Start and then lock or by press and hold the power button and choose the lock phone option. So one would say that it's still operational, so why bother about it, but I kinda liked the standard function and I have to freaking idea why it changed!!!
I'd be most appreciative if you could offer some help with that.
Oh, I forgot to mention. Soft reset didn't solve the problem. Erasing the calendar event didn't either.
My phone runs the factory ROM (1.66.482.1 ELL), I haven't changed anything other than user settings (yeah, I'm a noob... )
Thanks in advance!
Nasos
Pocketshield could be the end of your problems. You can try it for 10 days and see how it goes...
But why do I need to buy third party software in order to revert my phone to it's original operation?
No, this is not the answer I am looking for. I was wondering if you know of any kind of settings that might have changed by accident and caused this undesired behavior.
Thanks.
The best to return to normal operation would be a hard reset. Or you can spend a while trying.
You can try
HKLM\Software\Microsoft\Shell\Lockscreen\Enable=1
HKLM\Software\Microsoft\Shell\Lockscreen\Active=1
Thank you very much. I opted for the hard reset option... I hope it stays ok this time!
My HD2 also had some strange unlocking and unwanted calling.
I noticed it appeared when using the android style lockscreen.
When I changed back to the original one, problem solved
i had this too. the andriod lockscreen seems to be a bit buggy last time i used it, i accidentially called 7 random numbers
Hi,
I love my new HD2, but i've got the following problem:
The proximity sensor works doesn't work 10% of the time and because the touchscreen is so sensitive, i end up pressing random buttons with my ear or face. I've been manually locking the screen during calls which:
- is really annoying
- doesn't really solve the problem, screen lock during calls does not require slider to unlock, just a regular button and also has a hang up button on it, so it's pretty much back to the original problem.
I know that there's many custom apps out there that can circumvent this issue but i like the stock lock screen (with slider), i don't need another one.
What i need is an app that automatically locks my screen using htc's "slide to unlock" screen after i accept incoming call or after my outgoing call is connected.
If anyone can help me with this i would apreciate it.
why not try s2u2
it has ability to lock after call is connected
do u have something in way of proximity sensor? case or screen protector? i had similar problem but after making bigger hole in screen protector it works 100%
@brkix: i would like a solution that uses the stock lock screen if possible
@lake: i have nothing of the sort, but i confirmed in several forums including this one that the proximity sensor is not 100% reliable
I exactly have the same problem. in my case I want to place a call then want to put the phone in its case while training or running whatsoever and I would really appreciate of being able to lock the keys in order to avoid accidental touching.
schlox said:
I exactly have the same problem. in my case I want to place a call then want to put the phone in its case while training or running whatsoever and I would really appreciate of being able to lock the keys in order to avoid accidental touching.
Click to expand...
Click to collapse
man said everything
+1
SmartLock, offers incall and outcall lock. This may be your best option.
This CAB will lock the hardware buttons when you are in a call if that helps
http://www.cabcache.com/cabs.asp?cab=29
Do you have hair covering your ear?
Without wearing any head wear my sensor works 100% perfect.
Per advice in the second post, I've yesterday installed s2u2. Mates, this program works really good and answers my necessities. All I had to do was to put a short cut of the application to my main screen. Then, I just lock the device by tapping the lock button during a call.
There's even an option existing to lock the phone automatically when the backlight is off and/or during a call directly.
wingm4n said:
Hi,
... I've been manually locking the screen during calls ...
Click to expand...
Click to collapse
Oh well! Please, tell me how you do it!
I'd pleased if at least I could manually deactivate the screen in order to avoid touching button with my cheek!
I've been trying to find an option to lock screen during a call without succeed.
Thanks,
Cheers!
I have the same problem. This part fails.
Sorry, but I insist... wingm4n: how do you lock the screen during calls?
I still haven't been able to find such option
Cheers,
Up....
Hit start then lock(at bottom left side of screen) after dialing or answering a call.
i have same issue...not with keylocks but with the screen!!!almost every time i make or receive a call with my phone in my pocket or by ear hd2 make itself an other call or push lots of function..and this is very annoying!!!i don't like s2u2...really doesn't any solution exist for solve this problem???
thank you!
Cheers!!
Smartlock
Take a look at this:
http://forum.xda-developers.com/showthread.php?t=505032
It locks the screen during calls, and has some other settings as well. I've been using it for a while and it seems to work just fine. And best of all, its free.
in s2u2 settings, just set: "lock on talk" and deselect "lock device". in this way...lock screen will work only in a call. that's it
I used to have such problem during my first uses with the HD2, I would realize because all of a sudden I heard keypad tones (and so did the other person ) while hitting the dialer with my cheek.
After that, I started noticing IF the proximity sensor triggered or not.
It's not really "idle", it's just very "picky", you actually need your ear to cover it, and not just your head being in its way... I took te habit of checking the phone display with the back of my eye to see if it's on while I answer a call, and if it is all I need to do is to move it on my ear so I touch the area with the proximity sensor the display turns off again. Works for me practically 100% of the times now.
How to turn this off
I have a HD2 running the energy rom and when a call is connected it locks the screen. But I use google voice and need to be able to enter my pin. Anyone know how to get the screen not to lock during a call.