Related
Hello, earlier today i felt the device was very warm, i tried to switch it on but it dint respond, even to a reset. when i plugged it into the wall charger all i get is the right hand LED glowing red.
HELP!!!!!!!!!!! how do i hard reset it or get it to work again!!!!!!
i would call in orange care, but im out of the country and i really need the pda functionality!!!!
Unlucky. The 'red' light on most HTC devices indicates a serious power problem, usually it means that the battery is dead (as opposed to simply having run out of charge) or very close to death. You can probably get it working again with a new battery, if the incident hasn't damaged any other components.
i had this with my JJ after I accidently let the battery run down, I plugged it in and led went red and unit would not power on, left it plugged in started scanning the manual and web about a red led, 30 mins later, JJ just switched on and all fine.
It's worth a go and ive not had problem since
i dont think that was the case...
i have a feeling it might have been a short or something, because the unit was SERIOUSLY hot.....
nothing i did worked....until............
final time before giving up, the light was still red etc.
i figured what the heck, either way its dead and im going to get a replacement.
i then gave it fairly hard thump
the red light disappeared. i thought to myself, oh crap, i've really killed it.
then i reset it............. IT BOOTED UP!!!!!!!!!!!!!!!
and all my info still intact......brilliant.....im still going to try and get a replacement when i get back, but thank goodness.
and here i was thinking the last computer to respond to physical violence was the old 486'es hehehehehe
afhstingray said:
and here i was thinking the last computer to respond to physical violence was the old 486'es hehehehehe
Click to expand...
Click to collapse
Actually, it's called percussive maintenance, "the fine art of whacking a machine till it works"
hehe, i'm an IT technician and it's the first thing i try, especially with Printers.....
They don't teach you that on MSCA courses.....
I would recommend not using the machine too much until you can get a replacement battery if I were you. Lithium batteries will get very very hot (in some cases expand and ignite) if they are dis-charged too far. Most equipment which uses lithium technologies will have a voltage cut-off on the power input. As each cell is a nominal 3.3V-3.6V, this is often at around 3V in order to not discharge the battery too far. I would have hoped that this was a HARDWARE function rather than software. However with what you have described, if the voltage cutout was somehow disabled, then this could explain the problems.
Of the units that I have seen in the past like this, the red LED would describe the battery voltage being too low to safely power the unit (i.e. battery be dead). Generally a couple of minutes charge will bring it up to a safe working value. However, after 30 minutes this certainly should have been enough. On one of my motorola units, the battery has expanded a couple of millimeters as it starts to dissociate. It may be worth you checking to see whether the battery in your universal has distorted in any way.
Hmm the red light comes on mine all the time.
It just means the battery is low and the unit is charging. .
It should turn green when the battery is at or near optimum charge.
no....thats not the red, charging is orangy when i say red i mean PROPER red. battery is not distorted, and to the best of my knowledge the unit had a good charge, im pretty sure it must have been some kind of hardware short, and am going to call orange as soon as im back in the country.
dosent explain though why when i whacked it it started working again. the whack instantly made the light go out :wink:
i did a battery rundown test as soon as i got the unit, and posted the results on the forum, if the cut off was not working, i would have ended up with a red light then.
i dont have the manual with me now, but is there any documentation on the red light?
Found this site which had an online manual:
http://www.rich-michael.com/pdf/User Manuals/050802_Universal_Generic_Manual_English_CDL.pdf
What does the phone say in the Power Tab?
A really useful extract:
13 Notification LED Bi-color LED on the right side: Green and Orange
for GSM/WCDMA standby, SMS message, GSM/
WCDMA network status, notification, battery charging
status.
Bi-color LED on the left side: Blue andGreen for
Bluetooth system notification of powered-up and
ready to transmit radio frequency signal, and Wi-Fi
status.
Couldn't find anything else on the LEDs
Found this site which had an online manual:
http://www.rich-michael.com/pdf/User Manuals/050802_Universal_Generic_Manual_English_CDL.pdf
What does the phone say in the Power Tab?
A really useful extract:
13 Notification LED Bi-color LED on the right side: Green and Orange
for GSM/WCDMA standby, SMS message, GSM/
WCDMA network status, notification, battery charging
status.
Bi-color LED on the left side: Blue andGreen for
Bluetooth system notification of powered-up and
ready to transmit radio frequency signal, and Wi-Fi
status.
Couldn't find anything else on the LEDs
Sorry to drag up this old post.
My friend dropped my phone (Orange SPV C500) a few days ago on to a tiled floor. The phone didn't appear to be broken or faulty at all at the time. I even managed to use TomTom navigator to go to the airport, but for some reason when I looked at it before I went to sleep, the phone was off. I assumed the battery had gone (even though it should have lasted at least another day). I tried to plug in the mains charger, but the LED showed a red light. I left it plugged in while I slept, but it was the same in the morning. The phone won't power on at all. I've read that this normally happens on a flat battery, but I am pretty sure it still had juice for another day.
I brought a new battery, but to no avail, the phone still shows the red light when plugged into the mains. No light at all when plugged via USB to my computer. The phone won't power on at all.
It must have broke something when it was dropped. But I'm confused as to why it took a few hours to take any effect.
I also notice that even without the battery in the phone, the LED will still light up as red when plugged in to the mains.
I've tried whacking the phone now, but nothing. Anyone have any idea whether it can be fixed?
JOEJOETHEJOEY said:
Sorry to drag up this old post.
My friend dropped my phone (Orange SPV C500) a few days ago on to a tiled floor. The phone didn't appear to be broken or faulty at all at the time. I even managed to use TomTom navigator to go to the airport, but for some reason when I looked at it before I went to sleep, the phone was off. I assumed the battery had gone (even though it should have lasted at least another day). I tried to plug in the mains charger, but the LED showed a red light. I left it plugged in while I slept, but it was the same in the morning. The phone won't power on at all. I've read that this normally happens on a flat battery, but I am pretty sure it still had juice for another day.
I brought a new battery, but to no avail, the phone still shows the red light when plugged into the mains. No light at all when plugged via USB to my computer. The phone won't power on at all.
It must have broke something when it was dropped. But I'm confused as to why it took a few hours to take any effect.
I also notice that even without the battery in the phone, the LED will still light up as red when plugged in to the mains.
I've tried whacking the phone now, but nothing. Anyone have any idea whether it can be fixed?
Click to expand...
Click to collapse
this is damn scary! Every day more people add on to the "my univ's gone dead after a small drop" community :?
When my univ was brand new, a friend of mine dropped it from a coffee bar table 3 feet high, and i still heave a sigh! Cant believe nothing happened...!
But one thing i guess we all know, its a "drop" away to kiss our device good bye :roll:
hope you get it back up and running m8! look around the forums, there are lots of breakdown-solutions threads...
cheers,
San
nice work afhstingray
do you think it was a baterry problem.
i have often used my battery till tit just ran out, from what i read in the post it seems to be a bad practice. anyway to turn off the phone
i doubt it was a battery problem as i've been using it until now without problems. (i didnt get a replacement as soon as i got back cos im waiting for this unit to get a bit scruffy before i get it replaced)
i had this once on my c500 as well, but taking out the battery for an hour did the trick. so i dont think the problem is related.
i've dropped my universal quite a few times already and im happy to say other than a few annoying dings on the metal plate with the orange logo, its working fine. and 2 of the drops were pretty bad ones too, i thought for sure the screen would die or crack. guess i got lucky and it hit the floor at an angle not too critical
total stab in the dark but maybe a broken connection on charging circuit? that could be why phone was ok then battery died and its now unable to charge?
ViaraiX said:
total stab in the dark but maybe a broken connection on charging circuit? that could be why phone was ok then battery died and its now unable to charge?
Click to expand...
Click to collapse
wouldnt it have worked if it was plugged into the AC then?
Well my Exec was dropped onto concrete at the petrol station whilst I was trying to sort out TomTom and fill up my Yamaha R6 bike at the same time :roll:
No problems, just a couple of case marks.
I guess multitasking should be left to the ladies and computers :lol:
steverae said:
hehe, i'm an IT technician and it's the first thing i try, especially with Printers.....
They don't teach you that on MSCA courses.....
Click to expand...
Click to collapse
Also explains why Servers are built so solidly.
When you are trying to recover a server at 2am in the morning they need to stand up to all but a sledgehammer :twisted:
Hello,
Last night I am charging my HTC Magician until 100%. Yeah, full. Then I unplug it from the cord. I've check the battery meter, 100%. Then I using it for some phone call, internet and sms. The remaining battery is 96%. But, I dont know why, myself is checking the meter again. It show charging !!! What? I am not plugging it into power cord! But the backup battery show "_Charging" ... hmm .. what does the underscore character meaning on the backup battery? It is never charged, I always look it 100%. Thinks it an error, I restart the device using psshutxp.
But, what? Still black screen?
Hm, then I remove the battery and reinsert again. Not turning on. OW ow...it seems bad. I retry remove and reinsert, same. Plugging the power charger, the LED turning on RED. Hmmm...on each battery, RED is initial charging, when battery discharged fully, hm?
BUT I'VE CHARGING until 100% approximate 45 minutes ago!!
Trying again to remove and reinsert the battery without power charger.
It turns on! Wow! BUT ...
I am using Cotulla HTCMAG_WWE_O2 rom. When we do hardreset, cotulla rom have a progress bar, written "Erasing...please wait" right?
AND IT APPEARS!
OMG, I think the PDA is 'restored'. Hey, PDA, I dont do reset!
Damn ... I've lost all of my SMS and contacts ... bad news ... But I have backup contacts via activesync so dont need to worry. About SMS? Yeah, they're gone. Then I sleep. Hmm...SMS messages collected since aug 08 lost just because of this f*cking battery.
This morning, I want to going to work.
Hey, the PDA is dead again!
Try remove and reinsert, then press power button, LED turn on with violet color! (i think it was the combination of bluetooth LED and red coloured LED).
Trying several times, and then turn on again. Restored again.
It seems the battery needs to replace (ABSOLUTELY...since got this PDA, it turn off when 28% battery).
THE END..
Will going to a store to find a replacement battery.
I am using Cotulla HTCMAG_ROM_WWE_O5 Rom.
When I charging my HTC Magician until 100% the LED never change to green color.
Anyone have same problem with me???
yes, mine too. may be it rom's problem.
sounds a lot like you have a dead battery, try getting a new one, that should fix the problem.
I've had batteries that did all sorts of crazy stuff when they were dying.
if batery voltage is going down to 3.2V or less that mean it dying? I looked with powerDetect and when battery remaining less then 30% voltage is going down. and if it is less than 3.1V My magician turn off and I should turn on again. If I try turn on phone on less than 10% my magician turn off too. So that mean I should change my battery?
I don't know bout voltages etc. but if your battery is not holding charge well and/or is shutting off suddenly (mine used to do it at around 40%), then it is time for a new battery.
I recommend this one http://www.dealextreme.com/details.dx/sku.23962 (if you search magician you can also find the 1800mAh version.
the thing about these are they are fakes made by dealextremem, so they haven't been lying around for as long as some of the bateries on ebay etc.
on top of that they are really cheap with free shipping to boot.
but these batteries quality same than original? Because I don't want change battery or have explosion as I hear in news about other not original batteries
It is funny, people are beta testing a free stuff. Yet they complain like they've paid zillions for it. Sometimes those who complains most are those who intentionally sell Cotulla's works on their puny mobile phone shops. Instead of complaining, try contributing by experimenting on the software.
Keep it up Cotulla, Since you began the 6.1 you've been beaten and crucified for telling the world that it would work. Many thinks Cotulla is crazy and is dreaming. I salute one great Russian guy who once branded GAY and Crazy. Now he re written history, several times.
Let's just be thankful,
Salam.
you know, my battery used to turn off at 50%. because sometimes it uses it for backup battery so your data is not lost completely quickly. u should buy htc just like i did because the battery is very good. and by the way does anyone have a cooked rom for htc blackstone cause i want 2 upgrade it to wm6.5
Okay so I got my phone about a month ago, I had kept it stock for a week, went to a custom rom, and put it back to stock today.
Reasoning I went back to stock:
So I had been having an issue of not charging when I plug in the charger, the phone would recongized that it had been plugged in by bumping the battery meter to 100% instead of a charging icon. The LED light was blinking orange & green so I knew something wasn't right. I then proceeded to unplug the charger and saw that the 100% knocked down to 6% which it was at 8% when I plugged it in. After I saw that I removed the battery and tried a different battery ( brother has the same phone) and his was at 70% and I plugged in the charger and still the same thing happened.
So after this I have found out that it was the phone that had the issue as it was not charging the battery at all so I then returned to stock rom using my brothers battery and it still had the same issue.
I then saw the middle contact of the three golden contact on the back of the phone was sticking between the phone and the battery so I pulled out the battery and pushed the contact toward the phone and then I insert the battery back into the phone and then place the charger on it and then it started charging.
So now I need to confirm that this was the actual fix. Can anyone confirm that the middle contact is the actual one that charges the phone or was this just luck of the draw?
sorry for the long post but I thought this would be a big deal based on the design of the contacts aren't the best.
rlacsamana1989 said:
Okay so I got my phone about a month ago, I had kept it stock for a week, went to a custom rom, and put it back to stock today.
Reasoning I went back to stock:
So I had been having an issue of not charging when I plug in the charger, the phone would recongized that it had been plugged in by bumping the battery meter to 100% instead of a charging icon. The LED light was blinking orange & green so I knew something wasn't right. I then proceeded to unplug the charger and saw that the 100% knocked down to 6% which it was at 8% when I plugged it in. After I saw that I removed the battery and tried a different battery ( brother has the same phone) and his was at 70% and I plugged in the charger and still the same thing happened.
So after this I have found out that it was the phone that had the issue as it was not charging the battery at all so I then returned to stock rom using my brothers battery and it still had the same issue.
I then saw the middle contact of the three golden contact on the back of the phone was sticking between the phone and the battery so I pulled out the battery and pushed the contact toward the phone and then I insert the battery back into the phone and then place the charger on it and then it started charging.
So now I need to confirm that this was the actual fix. Can anyone confirm that the middle contact is the actual one that charges the phone or was this just luck of the draw?
sorry for the long post but I thought this would be a big deal based on the design of the contacts aren't the best.
Click to expand...
Click to collapse
On most cell phone battery packs the center contact(s) are a data or temp sensor connection, the power is input during charging and drawn during use from the outer contacts.
It depends on how "smart" the battery pack is that determines exactly what those center contact(s) do. In sophisticated packs there is actually circuity inside the battery back that monitors voltage, current draw and temp on the battery to determine the battery's charge status and communicates this back to the phone over a serial data bus with those contacts. on simple battery packs the center contacts are simply connections to a thermistor to monitor the battery's temp during the charging cycle, so the phone can cut off charging power if the battery starts to overheat.
In the end, yes, if the phone cant get a connection to those center contacts, it likely will not initiate a charge cycle. Attempting to charge a lithium ion with no way to monitor it is just asking for fire or explosion
d0ug's point above is backed up by the fact that several users have had issues with charging and/or booting the HD2 when that one middle pin gets bent (which seems like a fairly common occurance in this phone).
Ok, so i have been having the same issue and couldnt find any information till now.
Custom rom or not, if the middle term gets bent it will not charge right, also if the battery gets warm to a certain point it will shut off on you. I have also noticed, if your battery is below 50% and your using it intensively it will also stop charging the battery. When the status gets bumped up to 100% the led's will flash between red and green, this usually means there is an issue between the battery being over save charging temp, or a malfunction of the data sensor circuit in the battery. This is built into the hardware of the phone and is a safety measure.
This is from HTC Tech support this morning.
If any one elst can find out anything, im sure there would be people glad to hear.
Too bad the terminal being bent is from having to pull out the battery all the time
acessford101 said:
Ok, so i have been having the same issue and couldnt find any information till now.
Custom rom or not, if the middle term gets bent it will not charge right, also if the battery gets warm to a certain point it will shut off on you. I have also noticed, if your battery is below 50% and your using it intensively it will also stop charging the battery. When the status gets bumped up to 100% the led's will flash between red and green, this usually means there is an issue between the battery being over save charging temp, or a malfunction of the data sensor circuit in the battery. This is built into the hardware of the phone and is a safety measure.
This is from HTC Tech support this morning.
If any one elst can find out anything, im sure there would be people glad to hear.
Too bad the terminal being bent is from having to pull out the battery all the time
Click to expand...
Click to collapse
I've never had to pull the battery when it freezes. I just hit the red reset button. Is that not working for people?
crisisinthecity said:
I've never had to pull the battery when it freezes. I just hit the red reset button. Is that not working for people?
Click to expand...
Click to collapse
In my case, I just never have anything pointy enough to press the reset button, at least not as handy as just sliding the batt up and out by an inch or so. I think out of all the soft-resets I've done on my HD2, maybe 2 were by pushing the little button (yellow in my case)
hmm, i just checked my center pin, its still good. Like someone said above, i also reset my phone by just poping the battery out.
Also in the same situation that i usually don't have anything around to poke the reset button. I don't think ive ever actually used the reset button yet. All my previous WinMo phones had a stylus and the reset button was on the outside of the device, no battery cover removal, so the reset button was convenient to use. Battery removal seems like the simplest thing to do, if you're already removing the battery cover, just pop out the battery
How often are you guys having to reset your phones that way that you are damaging the pin, are you rocking the battery into it, or kind of just pushing it in? i noticed that the contacts seem to only fold down, they don't fold up or push in.
Ill definitely keep in mind now to put the battery in with a slightly downward motion to make sure the pins fold down, and don't get mashed in, which is where im guessing the bending is happening for you guys
My left pin got bent from all the battery pulls I've been doing. I think it happens when you don't slide it in at the right angle as d0ug has suggested. Now every time I do it, I make sure that all the pins are contacting correctly. If my left pin gets bent outward, the phone does not power up at all. (which made me freak out thinkin I broke it) Both stock and cooked ROMs have required battery pulls occasionally. Overall, I think I have to do battery pulls WAY WAY WAY more than I did with my previous MT3G. So far I have tried Kumars and Elegancia ROMs. I wish I could find a stable ROM that requires zero battery pulls. =T
yupp had the same problem with the connectors under the battery
I went in for a refurb and used it for a day and that pin was already bent so i went back in and this one seems to be in good working condition.
I think they should have done better job with the pins as I have never had these issues with any other phone.
WOW!! that fixed my problem.
*sniff* I love you guys! Thnx for the fix!
I'm trying out a couple of HD2s that an acquaintance had no business getting and is now looking to unload. The one is practically right out the box, the other looks like it has been around the DC loop a few times. I'm testing the well travelled one out when it looked like it needed charging, so I plug it in and start looking at the nice one. After 2hrs, I hear the tramp vibrate. When I go to see why it vibrated, it won't turn on again! It's after midnight, I haven't purchased it yet, haven't loaded a cooked ROM, haven't even run a stock update and it's already screwing up!?!? Since I had two I did some battery swaping then both went into boot loops. Many hours and a few gray hairs later, I got them both working again. I left them essentially alone until today. When the spouse went to sync the well-used of the HD2s, he noticed it needed charging. After almost an hour, he noticed that it had less charge than when he plugged it in. I noticed the charge light wasn't steady, it's flipping between red, green and nuttin'. My spouse, who had already laid claim to this HD2, did as he always does and jumped to the worst conclusion. I said make no inferences until we get home and check this forum. I knew you'd have the answer and you did not fail me! Best yet, it cost me nuttin' to fix!! Now do I point this out as a flaw for potentially lowering the sale price?
Thanks again!!
My take on this is that the flaw is in the way the battery wants to come out. When you lift using the tab on the left side, it tries to come out at an angle, angling from top left to bottom right, which means the connectors come away unevenly, and since the connector plates on the battery are inset, the plastic of the battery casing catches the pins as the battery rotates on its way up.
I keep my thumb on the battery just above the sim card until the battery is out about 45 degrees both top left and top right, and then pull it towards the top of the phone so the connectors all come away evenly, rather than being dragged up and over the pins.
After several cycles on WP7 the batt was fully drained and now it won't charge (charge LED goes on for few seconds and then goes off). It won't load either, just switches off on DFT screen. Batt is standard.
Guess it is critical not to allow batt to drain fully on WP7?
Is there any solution to this?
Thanks for any ideas.
Had a similar problem with Android...battery drained completely and wouldn't charge. I solved it by cutting the end off of a spare USB cable, removing the battery, and charging directly from the cable (red wire to positive/black to negative). After about twenty minutes I put the battery back in the phone and it booted Right up. Or, if you have more sense than me, you could just pick up an external battery charger...I'm just the hack apart a cable and do it caveman kinda Guy...
Sent from my HTC HD2 using XDA App
I can confirm a similar experience; I thought it was worth trying the fully-drain-then-fully-recharge regime suggested elsewhere on these forums as a means of extending battery life, which does struggle a bit on WP7.
The fully discharge bit was easy, but it is worth everyone bearing in mind that magldr - as advised, I believe - will not allow the phone to charge. As a result, I was getting into WP7 (just) only for it to almost immediately shut down. But it was at least doing a small amount of charging before it did.
After a sweaty fifteen minutes or so of restarts (I was having to take the battery out to force the restart as it wouldn't start on the power button), it decided it had enough charge to...well, charge and all was well.
My suggestion would be not to risk going beyond the critical warning WP7 gives, at least until magldr is able to offer charging.
Almost the same issue here, without having let the battery fully drained...
I can't charge my hd2 anymore.....if it's turned off.
But, it Can be charged if wp7 is running! I don't know why...
I had This issue when I received the phone. It took me a whole Day to charge the battery the first time : orange LED turning off after 10seconds (HD2 switched off or in wm6.5
Once the led is off, can't turn the phone on or charge it again until I remove and put the battery back.
It was in summer so I thought the phone was too hot, so I cooled the battery with a fan, replaced it, retryed... At least 10times, and it finally charged.
SO weird, I'll test This again with wp7, who knows?
I am wondering whether it is some kind of magldr bug?
I'll try the trick with the cable directly to the batt. It is not very practical though if you drain your batt, where there is no access to spare cabling.
bdkinney said:
Had a similar problem with Android...battery drained completely and wouldn't charge. I solved it by cutting the end off of a spare USB cable, removing the battery, and charging directly from the cable (red wire to positive/black to negative). After about twenty minutes I put the battery back in the phone and it booted Right up. Or, if you have more sense than me, you could just pick up an external battery charger...I'm just the hack apart a cable and do it caveman kinda Guy...
Sent from my HTC HD2 using XDA App
Click to expand...
Click to collapse
This should be put into the sticky rollup thread for people who have let their batteries drain.
Why dont you do some pics bud and create a topic?
I am cutting the cable as I write. Will take some pics.
If your battery drains completely, just remove it, replace it back. Without starting the phone, connect it to your PC. start and enter the bootloader. You'll be then able to charge. I did it like that last week.
Sent from my HD7 using Board Express
Running cable directly to the batt is confirmed to work. Just revived mine with this trick.
jemaho said:
If your battery drains completely, just remove it, replace it back. Without starting the phone, connect it to your PC. start and enter the bootloader. You'll be then able to charge. I did it like that last week.
Click to expand...
Click to collapse
How do you enter the bootloader, if the phone is not responsive at all?
adminlt said:
I am wondering whether it is some kind of magldr bug?
Click to expand...
Click to collapse
Less of a bug and more of an unwanted side-effect of having this excellent capability, I think. I seem to recall that the developers are aware and looking to see what can be done.
adminlt said:
How do you enter the bootloader, if the phone is not responsive at all?
Click to expand...
Click to collapse
I guess it is possible to completely drain the battery, in which case this won't work. But if there is some power, removing the battery and replacing it should kick the phone into life for long enough to do this. This was going to be my first try if persistent rebooting hadn't eventually worked.
having this problem and definitely charging below the amount...
i cant fully charge the battery as well
Like I said, if connected, but not started, to your computer, you'll have enuff time to start it then and entering the bootloader, of course, you gotta be quick for this to work.
If it doesn't respond, don't laugh, confirmed to work, remove your battery like explained and put it for some mins in the fridge before replacing it (it's only chemistry playing here, somehow better than cutting a USB cable in 2).
jemaho said:
Like I said, if connected, but not started, to your computer, you'll have enuff time to start it then and entering the bootloader, of course, you gotta be quick for this to work.
If it doesn't respond, don't laugh, confirmed to work, remove your battery like explained and put it for some mins in the fridge before replacing it (it's only chemistry playing here, somehow better than cutting a USB cable in 2).
Click to expand...
Click to collapse
You know nothing about chemistry at all! Cold kills battery charge if your going to use temperature use your armpit for 5 mins!
double post oops please delete
lilikin said:
double post oops please delete
Click to expand...
Click to collapse
"storing them in the freezer might be more practical. These kinds of batteries lose their charge after a few days when kept at room temperature. But they'll retain a 90% charge for months if you store them in the freezer. Just like alkaline batteries, you'll need to wait until they've warmed up before using them. However, this isn't a problem when you need new batteries for your digital camera or other electronic gadget. "
I suggest you to be more polite when answering and learn your lessons before posting!
I finally made a dual boot Android/WP7.
At first, Android said my battery was fully charged, just like WP7, which is totally impossible as I used MAGLDR to format the SD card (wp7 & android partitions) and that it took me almost 1hour, without any possible way to charge the battery while I'm in bootloader mode.
But when I turned the phone off, plugged into the wall.......TADAA It was finally charging, with phone turned off
So, it seems that dual boot may be a way to solve this issue
jemaho said:
"storing them in the freezer might be more practical. These kinds of batteries lose their charge after a few days when kept at room temperature. But they'll retain a 90% charge for months if you store them in the freezer. Just like alkaline batteries, you'll need to wait until they've warmed up before using them. However, this isn't a problem when you need new batteries for your digital camera or other electronic gadget. "
I suggest you to be more polite when answering and learn your lessons before posting!
Click to expand...
Click to collapse
You're arguing against yourself here aren't you? Cold may be fine for storage but you need heat to coax a little more power out. You even say 'you need to wait until they've warmed up before using them'.
adminlt said:
I am cutting the cable as I write. Will take some pics.
Click to expand...
Click to collapse
If you could do some pics that would be great...I have two, "My computer's broken," calls to deal with today. Visuals might help some...it's appreciated.
Wrong idea, sorry guys.
I thought that HD2 was charging since I installed WP7 and Android in Dual Boot. But it's a fake : if the phone is turned off, and that I plug it, the orange led turns on. But that's all, even if I unplug the phone, the led remains turned on !!
And now, Android as well as WP7 are telling me that the battery is fully charged but I'm sure it's not even 50% full.
Not sure if it is a bug, or if the screen-pinning is actually working to perfection. IMO it works a bit too well for comfort.
Was playing the most recent riptide game, and to do tricks I usually ended up hitting the hardware touch keys, so I turned on screen-pinning to counter that. Well, apparently you don't receive anything from the system (battery low warning etc...) while it is on, AND the system cannot overrule it. Meaning even if the battery goes to 0%, it won't shutdown/poweroff.
The phone literally turned off in a snap, screen flashed kinda weird colours and puff! Off!
When I tried turning it on, the usual multi-lingual red writing saying battery is low appeared and disappeared in an instant, instead of the usual 1-2 seconds being displayed.
I plugged the Dash charger and the red writing appeared instead of the charging symbol. It took like 3-4 minutes charging before the phone "turned on" to display that lightning/thunder image that informs you it is charging. I think dash charging only activated at that point.
Haven't turned it back on yet. Gonna take advantage of this and charge till 100% for the calibration X_X
I think that the red writing when plugging in your charger actually should be a charging message which however is the same like the low power images (there are two images, one called lowpower, one called charging, both contain the same data)
Running the battery down to completely zero can brick your phone. The phone needs a very slight charge to recharge. The system shuts it down very slightly early because of this. You often see people bricking their phone because they completely discharge in recovery.
B3501 said:
Running the battery down to completely zero can brick your phone. The phone needs a very slight charge to recharge. The system shuts it down very slightly early because of this. You often see people bricking their phone because they completely discharge in recovery.
Click to expand...
Click to collapse
yes, discharging completly your battery wont have a positive effect for you - its the other way round.
but if you think you will get a "recalibration" thing or something.. then go ahead and have fun with your placebo effect