Hey guys i tried flashing my rom using the Shelltool. I loaded the two cabs on the device and put it back to Tmobile 2.26. While i was in the shelltool it told me to do a hard reset and i think the phone was frozen (it didnt go to the normal colorful screen like usual) so i took the battery out of the back and powered it on. I left the software running like it said but it just froze up.
Now my MDA wont move past the Tmobile screen. I REALLY need a hand with this because this phone keeps my life in line! I dont even think ill be able to get up tomorrow because all my alarms go off my phone
Let me know if theres anything i can do otherwise im looking at a Motorola A1200 :-(
kind regards,
Eddy
Hi there,
Not familiar with Shelltool. I do most of my flashing using ActiveSync. Have you tried forcing the phone into Bootloader Mode (hold the Camera button while turning it on). Worth a shot.
If t-mobile was the original ROM on the phone, then just flash it again using the exe (or RUU if you extracted the files from the exe) instead of using shelltool and see if that brings it back to life.
well its stuck on the tmobile splash and shows no actual connection to the machine would it still work?
If you can get into bootloader mode then you should be fine. Just put your device into bootloader and flash wizard love rom or the rom that your device came shipped with.
Good Luck
looks like its working guys but its most likely still going to look and be WM5. Im still willing to try and get WM6 on it tho. I have the roms but its just not working any ideas?
Well, if you're flashing the t-mobile ROM right now then it is going to be WM5. Since you now know what to do if the ROM your loading doesn't stick, try flashing the ROM you were trying to flash again. By the way, what was your IPL and SPL before you flashed it the first time where it didn't work? If it was less than 2.xx then that was your problem most likely. If you're now updating to the latest t-mobile ROM the way I told you to (using the exe or RUU) then your IPL and SPL now should work fine with WM6.
Well I just finished upgrading my MDA to WM6. Here's what I did. First off I
fould out that you need the phone CID Unlocked for it to accept the WM6
ROM. Follow the instructions on this thread by Dr. Puttingham.
http://forum.xda-developers.com/showthread.php?t=285435
This should get your MDA ready provided it is a G3 (thread will tell you how
to tell the difference.) Then follow the directions on mfrazzz's thread:
http://forum.xda-developers.com/showthread.php?t=324632
I had problems with my MMS after the update but after re-installing the WM6
ROM and installing the CAB files by Lurch anf FZZF I got that problem
squared away. Believe me when I say I know what you are going thru. I
was fiddling around with this for about a week. Luckily I am on vacation and
I had plenty of time to read and decipher alot of the info I found. Good luck
and remember to READ, READ, READ. BTW, props to all that contributed to
these fine tutorials and for this awesome ROM. I have it running on my MDA
for three days now and am very happy with it. I am also using the 3.08
IPL/SPL which seems to give me better reception, which my wife seems to
appreciates
!!!
I just tried to do the 3.16 update via dcd's instructions and now I see this, frozen at the sprint splashscreen. I tried a hardreset
I got until step 3 -- Flash new ROM, it went through no problems
WHAT TO DO!?
PLEASEe HELP <3 thanks in advance!
read..why flash a rom if you cant read?!
if i remember correctly, it is because dcd's rom doesnt include the new sprint radio.
either flash the sprint radio by itself, or flash the unofficial sprint rom followed by whatever ya want after that
of course it's gonna be a pita since you didnt do your research beforehand. tsk..tsk...
SOLUTION
Actually I think you did everything right...
... you just overlooked the same thing that I did ...
The instructions are a bit vague on one thing (for those of us who haven't done much rom flashing before)
You must load the new radio BEFORE your new rom will even boot!
----------that is why you are hanging on the yellow Sprint boot screen------------
1. This means you need to go back into "boot loader mode" (hold power and camera and reset with stylus)
2. Then run titan_radio_3.27.00.exe while your phone is hooked up via USB)
After that finishes you should be rockin with the rest of us!
Im trying to load a custom rom onto my XV6900. I got everything together and went a head but ran into an issue. I'll start with all the phones history. I got it and then when the update to 6.1 leaked I installed that. Now just recently I started by following this tutorial http://www.atwistedweb.com/xv6900/index.html. I completed everything up until install upgraded radio with no problems. Then on this step I kept having an issue where it would flash loding but then just go to the boot screen and not do anything. After playing with it for a while I figured maybe the 6.1 update took care of this so I moved on. I got the same problem with the next step which after a little bit I figured out was because I wasnt formatting the card correctly. So then I started the ROM flash with no problem. It loaded and the progress bar completely filled up quickly. The issue is now it is just stuck saying update in progress and has been for about 20 min. Im not sure if its because I didnt do the radio update or if its somthing else. I figured before I do anything I would see what people suggest I should do next. Should I soft reset? Do you think its bricked now or will I be able to try another flash? Please let me know where to go from here. Oh and also the rom im trying to flash is this one http://forum.xda-developers.com/showthread.php?t=432487
thecaptain0220 said:
Im trying to load a custom rom onto my XV6900. I got everything together and went a head but ran into an issue. I'll start with all the phones history. I got it and then when the update to 6.1 leaked I installed that. Now just recently I started by following this tutorial http://www.atwistedweb.com/xv6900/index.html. I completed everything up until install upgraded radio with no problems. Then on this step I kept having an issue where it would flash loding but then just go to the boot screen and not do anything. After playing with it for a while I figured maybe the 6.1 update took care of this so I moved on. I got the same problem with the next step which after a little bit I figured out was because I wasnt formatting the card correctly. So then I started the ROM flash with no problem. It loaded and the progress bar completely filled up quickly. The issue is now it is just stuck saying update in progress and has been for about 20 min. Im not sure if its because I didnt do the radio update or if its somthing else. I figured before I do anything I would see what people suggest I should do next. Should I soft reset? Do you think its bricked now or will I be able to try another flash? Please let me know where to go from here. Oh and also the rom im trying to flash is this one http://forum.xda-developers.com/showthread.php?t=432487
Click to expand...
Click to collapse
Ok, just try and download nfsfan's 6.5 rom, put you phone in bootloader mode, (power,camera, softreset) The colored icoke screen should come up. Connect your phone to your computer with your usb cabe, on the bottom of the screen it will say usb connected (or something like that). Than just run RomUpdateUtility in the zip file you downloaded with the rom. It will connect to your phone and update it. After it's done, before it loads into windows perform a hard reset (send key, end key, and softreset). Once it's doing restoring again, allow it to boot up.
Should be okay after that. I've done several of them with no issue. Sometimes in rare cases you need to flash the latest bell rom first, and than update to nfsfan's 6.5 after that. Don't worry it won't 'relock' your phone.
Good luck
Ok here is an update on the phone. I tried installing the radio update but it froze on cdma. So then I grabed the verizon 6.1 update and reflashed it. So now im back to square one. What steps should I follow from wm 6.1 to a custom rom? Do I need to do the radio update or is the Rev A. included in the 6.1 update enough? If I need to do the radio update how would I go about that? Then is there a better process to follow for the ROM install?
thecaptain0220 said:
Ok here is an update on the phone. I tried installing the radio update but it froze on cdma. So then I grabed the verizon 6.1 update and reflashed it. So now im back to square one. What steps should I follow from wm 6.1 to a custom rom? Do I need to do the radio update or is the Rev A. included in the 6.1 update enough? If I need to do the radio update how would I go about that? Then is there a better process to follow for the ROM install?
Click to expand...
Click to collapse
What are you trying to accomplish? Do you simply want to flash a custom ROM or do you want to unlock the GPS too? If you are trying to unlock the GPS then this tutorial may not help you. http://www.atwistedweb.com/xv6900/index.html
I assume that your phone is already unlocked with 2.31. Once your phone is unlocked all you need to do is flash your custom ROM. This is unless you want to unlock the GPS. I would not worry about upgrading your radio just to upgrade it as there probably no benefit. I wouldn’t do it unless you knew of someone in your area that had success with better signal.
If you want to unlock your GPS I would follow this tutorial. As people have had success.
http://wiki.ppchaven.com/index.php?title=Pocket_PC_WIki:FIX_VERIZON_GPS
[1] Unlock with 0.40.coke
[2] Flash Sprint ROM RUU_Vogue_SPRINT_WWE_1.12.651.1_2.13.00_SPC_NV133_Ship DO NOT LET CUSTOMIZATIONS RUN
[3] Unlock with 2.31.coke
[4] Flash Verizon ROM RUU_Vogue_VZW_WWE_3.14.605.1_Radio_3.37.77_Ship DO NOT LET CUSTOMIZATIONS RUN
[5] Flash any custom rom
[6] Skip
I would recommend using NFSFAN’s ROM. The above procedure should allow you to use your GPS with TomTom, Garmin, & such.
do the tutorial above for gps.
and if you need more info or want stuff to customize it, go to my faq,
but the above walkthrough is the one you want if you plan to use gps.
Verizon xv6900. This Is my first time flashing to a new rom, & I need help. I have a couple of questions to ask anyone that owns a vogue. Do I put bootloader mode.exe onto my storage card or on my phone.
And im trying to flash to NfSFAN's 6.5 Rom. But It Keeps Getting Stuck At 0%.
Do I need to unlock my phone first or what
yes you need to use icoke first.
My phone keeps restarting now! what should i do
GSM4ever said:
My phone keeps restarting now! what should i do
Click to expand...
Click to collapse
put it in bootloader pwr+cam+reset hole then try to flash again
ughh.
im in bootloader mode to keep it from restarting which rom should i go to. like a stock verizon one.
Use icoke 2.31 first to unlock the phone. Then flash the rom you want using BootLoader. I think thats what your problem is. I had the same problem because I am a N00b at this as well.
first unlock using cokeman's unlocker.
http://forum.ppcgeeks.com/showthread.php?t=20370
theres a link in that thread
optional step:
go back to stock rom
http://forum.ppcgeeks.com/showthread.php?t=19071
then go into bootloader
(power+ camera+reset hole)
and flash
nfsfans 6.5
i actually used .41 unlocker and i had to update radio, use another carrier's rom, and reunlocked it to 2.31 unlocker then flashed it back to stock rom, unlocked it again, and now i have nfsfan's 6.5 and it works GREAT.
after my phone rebooted once the update was complete, it wont get passed the "at&T World Phone" white screen... SOMEONE PLEASE HELP ME!!!! i was using a stock at&t pure with the stock rom. i can not upgrade hardspl or ANYTHING any suggestions on how to get my phone to boot? hard-reset went through with no signs of failure but it still will not boot up after that finishes... sorry if its something im overlQQKing, but i just cant figure it out. n yes i have researched although obviously not enough at this point. Thanks to anyone who can help in advance. forgive my stupidity!!!
......
noone?????
The HTC Pure updates hosed my phone too, I had already applied hard-spl to my Pure and i've flashed it with dozens of roms. Since I was currently using one of the "Stock" AT&T roms posted on XDA I figured I could apply the updates. Unfortunately after applying the update my phone froze at the boot loader. I was forced to flash my rom using the memory card method and then restore a backup.
you could try putting the phone in SSPL mode manually, (reset button+volume down), the run hard-spl hard-spl in manual mode.
you can then flash your rom using the memory card method. (FAT32 formated memory card, rom file renamed to topaz.nbh copied to root of flash card, reset button+volume down to enter SSPL, power button to confirm flash).
All this assumes you've already tried to hard reset your Pure (reset button+vol up+vol down)
Thanks for the reply! Unfortunatly, i tried the manual method and after it hanging at 0% for about 5 minutes, i keep getting error [262] update error.. (communications error) is this becuase i can not sync with mobile device center (win7)? I really dont want to just have to toss the phone! I have had an at&t tilt, at&t fuze, and now the at&t pure, and this is the only phone i have had this problem with for some reason...
Try Unplugging Your Pure From the computer Take Out the Battery Put the Battery Back in Mean While Restart your computer and Press Power And Volume Down At the Same time on your Pure If its on the colored screen your good,..Make sure your system is online and your not downloading anything and plug in your Pure to the computer it give it about 2 minutes to download the HTC USB driver then once its done your phone will say USB on the bottom of the Red Green Blue And White four color screen Then open up one of your ROM's and Flash it,....Do You Have Windows Mobile Device Center Installed?
If Not here is the Link
http://www.microsoft.com/windowsmobile/en-us/downloads/microsoft/device-center-download.mspx
If you do already you need to uninstall the Driver update for windows mobile media center then install it again .
i can get the bootloader screen just fine! i just can not get hardspl to flash onto it. it sits at 0% every time. the phone will not boot so i can NOT get into mobile device center. The tri-colored screen comes up with no problem and it says USB on the bottom, so the drivers are already installed. I even tried hard-reset and still no luck
There was an additional cab file I needed to install to HSPL the Pure
"enablerapinew.cab"
basically the machine just would fail to load the HSPL without it
but it still functioned afterwards, does yours?
Do a search on XDA find and DL the cab (or I could attach a zipped copy)
If you can still access the device,
just copy enablerapinew.cab to any temp dir on the device
the execute it through fileexplorer
then go back to installing the HSPL (mine then worked fine)
If you haven't already, You should go to
http://forum.xda-developers.com/showthread.php?t=520312
you'll find troubleshooting info and a link to the extra cab there
If you really are bricked at this point , it sounds like nothing has actually
been changed on your device yet? its just frozen should be still under warrentee? Unless anyone else has a better suggestion you should be
able to return it for exchange to ATT
Good Luck
KJL
It sounds like Windows is not properly recognizing your device when it is plugged into the USB port while in SSPL mode.
Have you tried different ports?
Is there another computer you can use?
another thought about returning under warranty
on the boot page of the stock Pure it indicates HSPL 1.83.000
After you update the HSPL it will say HSPL "1.83.Olinex"
this normally an indication of a successful update,
but it will probably void your warranty if they just look at the boot screen
This is true for all Pure (and Tmobile Compact V) Rom upgrades
The Stock Pure came with 6.5 and therefore the 1.83.00 HSPL
The Diamond2s did not, so their solution which reverts to 1.63 <?>
will not correctly revert to 1.83.00 on the Pure.
No way to correct this yet as far as I know,?
All the "reverts" are geared toward the Diamond2s, not the Pure.
But If your boot screen indicates 1.83.00 before it freezes
I'm fairly sure its still entitled to a warranty repair/replace
How could they tell the cause of the failure
was a reburn as opposed to natural causes?
Good Luck
KJL
When you put the phone into a manual bootloader mode... Mobile Device Center becomes obsolete.
HardSPL is only needed for unofficial roms. Forget HardSPL for the time being. The goal here is to get your phone operational. Just download the official HTC WM6.5 WWE rom and flash that. Put phone in manual bootloader mode and run the Rom installer.
As long as your phone is in bootloader mode and says "USB"... then your set to go.
Another solution is to try another PC. You'd be surprised how often that will resolve your issues. Perhaps find an XP machine and install Activesync (so it loads the bootloader USB drivers). I had to do that on several occasions when my main PC refused to flash my mobile device.
I did both of the updates htc has for the pure. Both worked fine. I am on the origianal rom. It does reboot your phone and stays on the white screen for a min then it loads the update and the phone starts.
The offical ROM comes back with a wrong vender ID error I guess cause its a "pure" and not the HTC branded "topaz"... NOW what should i do??? Seems like i NEED hardspl so i can flash any ROM, as from what i researched, there IS NO AT&T Pure rom that has been released. I still cant figure out why a hard-reset will not work though.... This is REALLY starting to get me angry!!!
Just for reference, the Pure's ID is TOPA210 32M
SPL-1.83.0000
The official hotfixes worked fine for me as well. Did you apply the hotfixes on the original ROM that came with your Pure?
Also, does the official HTC Touch Diamond 2 ROM work for you? If so, the hotfixes for the Pure are irrelevant, as are any future updates released for the Pure. You should look for updates for the Touch Diamond 2 on the Worldwide HTC site.
If you needed to do a warranty claim, the closest you can get to returning your phone to stock/shipped form is to use the ROM dump using HardSPL and hope they don't notice that the SPL is different. Currently, there's no way to return the Pure back to completely official software.
A hard reset simply wipes everything off and restores everything back to what is contained in just the ROM you currently have on it. If you've flashed your phone at all, you've already wiped out the original ROM that came with it.
It is still the STOCK ROM. I have never flashed it yet.. The topaz rom will not flash due to a vender ID error. The spl is still stock also... i think thats is why i am having this problem. I bought the phone off craigslist so returning it to AT&T is NOT an option either way. My only solution is to find a fix. (or trash it) I really appreciate all of your suggestions and input so far. You guys are by far the best board around! I am a LONG time follower, but a few-time poster. Obviously i have little to contribute to the board.
Can I trouble you to dig up a few version numbers? It'd help evaluate your situation so we can see which options are best for your case.
ROM version? You can find this in Device Information. Start --> Settings --> System --> Device Information
Bootloader version? Do a soft reset while holding down the volume down button on the side until a screen with red, green, blue, and white, ordered top to bottom, shows up. It should be the second line starting with "SPL-..."
The ROM is the STOCK AT&T ROM (again...) I CAN NOT go to start;.... because if you noticed in the first post, the phone will not boot past the white "AT&T WorldPhone" screen... the spl is stock also incase you missed that part. (1.33.0000) I have never flashed the divice. EVERYTHING IS HOW AT&T SELLS THE PURE OUT OF THE BOX! NO MODS. NO FLASHED ROMS. NO HardSPL... NOTHING! STOCK!!! (for those overlooking the details in my previous posts) I have no doubt you guys (n hopefully a few girls ) will help me fix my issue. I'm just REALLY anxious for it to happen sooner than later!
Have you tried downloading the official rom here on xda and renaming it to TOPAIMG.nbh and update using the sd card method?
Here is the thread:
http://forum.xda-developers.com/showthread.php?t=600339
The download is in post #1
I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!
jromeo350 said:
I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!
Click to expand...
Click to collapse
You can flash hard SPL the same way by renaming the .nbh file to
TOPAIMG.nbh
jromeo350 said:
I have downloaded the official ROM. Although I thought it is still concidered "custom" and that you need spl updated to install it... Am I wrong about this? Also, by using the SDcard to flash, do I NEED to have hardspl on the device? If yes, I can not use this method, as I have stated before that the spl is still stock and NOT updated in any kind of way. NOTHING on the phone has been updated or flashed. Will this method still work then???? I am at work for 3 more hours and then will go home and try it either way and come back to update you all on the results. Again, THANK YOU for your continued support in helping me out!! At this point, I will send a donation via paypal to whoever can get me out of this hole!
Click to expand...
Click to collapse
Actually that is supposed to be an officially signed rom. If that is true it will work with the stock spl. It will either work or it won't. Also, as stated in the response after yours, you can apply the hardspl via SD as well.