Is there a apk of a file I can install to refresh the radio.. my signal been jacked up for the last 24hrs.. and I might send it back to tmobile...
And what is the imei sv field supposed to say in phone info.. mine is blank
if you can use the debug you can reset the radio in the command promt... I believe the command is "radiooptions 0"
how do i debug? and what does reseting the radio do?
cause the signal ive been getting went bad last night and i was gonna send it back to tmobile
debug by going into settings -> applications -> developer -> debug.
Then connect to your computer and use the debug drivers found on the forums, and the SDK from google (or on the forums too, read the wiki for that info)
Then unzip the SDK and open a command prompt. Go to the folder you extracted and under the tools directory enter "adb shell radiooptions 0" that should be it, it will reset the radio by turning it off and then back on... It also does other things that you don't get when turning it off and on.
fam, did u root yo fone?? Cuz tmobile gon look @ it if u did. N they gone give u bull**** about the warranty...n charge u stacks on deck 2 pay for the service charge or replacement....make sure to flash back 2 rc29 first if u sendin it back
ashabanf8 said:
fam, did u root yo fone?? Cuz tmobile gon look @ it if u did. N they gone give u bull**** about the warranty...n charge u stacks on deck 2 pay for the service charge or replacement....make sure to flash back 2 rc29 first if u sendin it back
Click to expand...
Click to collapse
english please, try and keep the txt slang off the forums.
Related
i did an update using the orange rom and it stopped at 80% with an error now when i turn it on it basically stops at the Bootscreen. I tried all methods from this site.
If i send it to HTC to be repaired (its still in warranty) can they fix it and if yes for how much?
1. Disable Activesync: connections -- settings -- uncheck "Allow USB Connections"
2. Take out battery, sim, and sd card
3. Look at your phone for SPL version. Mine was 1.40.
4. Run RUUWrapper.exe on a ROM that you know would work. I used LSVW VP3G. Choose 1.40 bootloader option on the phone bootloader option.
5. Wait, don't hook up USB cable to your phone yet. Check the box where you're agreed to upgrade then hit Next
6. Now hook your phone to activesync and let RUUWrapper picks it up.
7. That's all. I guess if it didn't recognize your device at step 6, then I would try again if i were you.
this did not work ????????
i must of brinked my phone 20 times all ways works for me..
I alway keep a copy of the original ROM of the variants (3.6 of whoever) I am flashing. I had experienced having the bootscreen and alway solved it by flashing back the original ROM (in my case it was the TM 3.6) and it alway works.
rmvembe said:
i did an update using the orange rom and it stopped at 80% with an error now when i turn it on it basically stops at the Bootscreen. I tried all methods from this site.
If i send it to HTC to be repaired (its still in warranty) can they fix it and if yes for how much?
Click to expand...
Click to collapse
go get origianl orange rom and flash that
it will cost about £100 to send to htv and get it repaird
you could always send to me if your in the london lol
dont worry theres always a way out of these isues ,
jdac21
lodger said:
1. Disable Activesync: connections -- settings -- uncheck "Allow USB Connections"
2. Take out battery, sim, and sd card
3. Look at your phone for SPL version. Mine was 1.40.
4. Run RUUWrapper.exe on a ROM that you know would work. I used LSVW VP3G. Choose 1.40 bootloader option on the phone bootloader option.
5. Wait, don't hook up USB cable to your phone yet. Check the box where you're agreed to upgrade then hit Next
6. Now hook your phone to activesync and let RUUWrapper picks it up.
7. That's all. I guess if it didn't recognize your device at step 6, then I would try again if i were you.
this did not work ????????
i must of brinked my phone 20 times all ways works for me..
Click to expand...
Click to collapse
only problem is that activesync does not recognise it but if you use USB monitors they pick it up and its shows as 'HTC DEVICE' when you run an update it shows the packet data going in and out then says your phone cannot be detected afterwards.
i can run the RUUWrapper it works up to 1% then the phone restarts and it then displays an error code check the attachment
i dont even know what to do i can even send it to you to try im not desperate but i just need it to work...or it would have been money down the drain get me
Hi everyone,
Ok, My names Z and I have been reading the forums on this site regarding TMO Wing and flashing over and over again. I then felt confident enough to flash my Wing using USPL. ( following this thread http://forum.xda-developers.com/showthread.php?t=421304 )
I can only get to step 7. ( Step 6. Follow the directions on the screen. EXACTLY.
* Your screen on your cell phone will go white around the 75% part of the "second step" now.
* ActiveSync will LOOSE its connection.)
upon reaching 7 my screen stays white then the RUU pops up (my screen stays white) but i get an error that reads ERROR 203, now all i can do i click exit.
My Spl is 4.26.
My Ipl is 4.26.
I have tried this 6 times
Thanxs for the help.
Z
Try re-installing the USPL again
http://www.megaupload.com/?d=A4N36HLO and the you open it and open the RUU file copy and paste whatever nbh rom you want to flash run the herald uspl hit enter its going to prompt you then hit enter again this time you screen should go white at around 75 and when its at 100 active sync will disconnect by itself and reconnect then follow steps from there. Make sure you check all boxes and agree.
The best way to ensure that your rom will flash well i always flash the OEM wing rom first... I use the upgraded v. I have it if you need it.. Try all the steps again and again.. One thing i have noticed thou.. If you leave your wing on for a little well hooked up to activesycn it has stupid problems.. IDK why but eh.. I just disconnect and try again.. If you need ne help let me know... pm me.. I made a detailed step by step video on flashing the wing but stupid youtube kicked if off!!!!
THANX
lol, what an idiot, well me of course! It seems that i had the TMO stock rom in my RUU folder instead of the custom one.
well thanks for the reply though. I wouldn't have noticed it if i hadn't re-downloaded the USPL.
Hello. This is my first time when I'm upgrading my Blackstone ROM and I get some problems so I cannot upgrade it
I think the problem is with active sync, but just I think like that maybe I'm wrong. First of all my active sync cannot connect the phone if the box is ticked for "Enable Faster Data Sync" I tried to reinstall active sync, version still not working. When the box is not ticked the active sync connect the phone but when I go into Rom upgrade setup and try to upgrade the ROM the phone restarts ant freezes in 0% of upgrade, then I get a windows with Connection Error. I take the battery out ant turn on my phone normally again.
Do you know how to solve this error? Or can you tell me other ways which I can upgrade my ROM? I know that its possible to upgrade via memory card but I don't know how. Thank you!
dnlaod any ROM, extract the file then u'll see a file named "ruu_signed.nbh"
change its name to "BLACIMG.nbh" then put it into ur storage card.
Go to bootloader mode then press power button n wait.. after ROM upgrade jus Hard reset it..
PS : read the WIKI
Sw1pe said:
Hello. This is my first time when I'm upgrading my Blackstone ROM and I get some problems so I cannot upgrade it
I think the problem is with active sync, but just I think like that maybe I'm wrong. First of all my active sync cannot connect the phone if the box is ticked for "Enable Faster Data Sync" I tried to reinstall active sync, version still not working. When the box is not ticked the active sync connect the phone but when I go into Rom upgrade setup and try to upgrade the ROM the phone restarts ant freezes in 0% of upgrade, then I get a windows with Connection Error. I take the battery out ant turn on my phone normally again.
Do you know how to solve this error? Or can you tell me other ways which I can upgrade my ROM? I know that its possible to upgrade via memory card but I don't know how. Thank you!
Click to expand...
Click to collapse
have u updated ur SPL... or r u using USPL..
IF u have then just boot into the boot loader and connect to USB and flash..
ignore the RUU saying that u need to be connected in active sync...
Moved out of development
cvchetan said:
have u updated ur SPL... or r u using USPL..
IF u have then just boot into the boot loader and connect to USB and flash..
ignore the RUU saying that u need to be connected in active sync...
Click to expand...
Click to collapse
I don't even know what SPL or USPL is. I told you this is my first time so i don't know those sort words. Can you explain properly what is those spl or uspl? thanks
bjy8138 said:
dnlaod any ROM, extract the file then u'll see a file named "ruu_signed.nbh"
change its name to "BLACIMG.nbh" then put it into ur storage card.
Go to bootloader mode then press power button n wait.. after ROM upgrade jus Hard reset it..
PS : read the WIKI
Click to expand...
Click to collapse
Thanks! I'm going to try your way today when I'm gonna come back to my home.
Sw1pe said:
I don't even know what SPL or USPL is. I told you this is my first time so i don't know those sort words. Can you explain properly what is those spl or uspl? thanks
Click to expand...
Click to collapse
This is all explained in the wiki. Before you do anything, best advice I can give you is to read up on SPL, USPL first!!!
Also, if you follow cRaCKwHoRe's guide (see my signature) you cannot go wrong.
Fallen Spartan said:
This is all explained in the wiki. Before you do anything, best advice I can give you is to read up on SPL, USPL first!!!
Also, if you follow cRaCKwHoRe's guide (see my signature) you cannot go wrong.
Click to expand...
Click to collapse
Ok. I will read it later. Thanks!
I'm still having a problem I have have read a wiki and I follow Dummies guide steps but I'm still having a same problem ( Stuck at 0% )
HSPL1 - Downloads
* (HSPL1a) HSPLWrapper_Blackstone_156OliNex.zip
* (HSPL1b) A 1.56+ based rom- Dutty's XT 3.7 linked here
* (HSPL1c) BlackstoneRUUWrapper.zip
* (HSPL1d) Extract each item to its own folder
HSPL2 - Flash new SPL (1.56.OliNex)
* (HSPL2a) Place your phone into its bootloader.
* (HSPL2b) Run HSPLWrapper_Blackstone_156OliNex.exe from the download in step (HSPL1a) and follow it as normal.
I follow these steps but at the last one my phones just freezes at 0% of update, so I can update to 1.56.OliNex SPL
Is me here doing something wrong or is it something wrong with my phone?
Does any one know whats wrong?
never mind. fixed by my self
Sw1pe said:
never mind. fixed by my self
Click to expand...
Click to collapse
how?? i have same problems..
i keep getting error 244 wrong device id when i try to flash a radio or rom. i looked it up and it says it's because i'm trying to put an hd2 rom on a phone that now thinks it's a hd7. how can i revert this so i can put a new radio on it to improve my data reception? thanks for your help
Turn your phone off. Press and hold the volume down button and then switch it back on. The phone should enter the bootloader (3 coloured screen). It should say "serial" at the bottom of the screen. Plug your USB cable in and wait for it to display "usb". The follow the instructions in various other threads on how to flash a different radio with custom ruu.
maxtap said:
i keep getting error 244 wrong device id when i try to flash a radio or rom. i looked it up and it says it's because i'm trying to put an hd2 rom on a phone that now thinks it's a hd7. how can i revert this so i can put a new radio on it to improve my data reception? thanks for your help
Click to expand...
Click to collapse
Interesting problem. A hard-reset won't change anything and reflash WP7 also not?
Try to delete the deployed .xml file from the Windows-Folder (use TouchXplorer) and then rerun the HDT Connection Wizard. Maybe it sets it back to default.
You can't hook up the phone while you're booted into wp7 and run a flasher expecting it to work like it did with winmo... it's not gonna work when you undo the registry either. You have to go directly into bootloader and run flasher then. No reason to undo your registry changes.
Also, in response to the person suggesting to delete the custclear file from windows folder... that won't work because it's deleted anyways when you run connection manager. You would have to create a new provxml, run and then do the custclear thing again to change your registry again. But, like I said, to change radios, it's unneeded.
thanx guys i got it to work. i restarted my computer and phone and it allowed me to flash it. thanx for you guys help
I installed maglar 1.12 on my hd2 using the nbh file method... now my hd2 wont turn off it just restarts as soon as you turn it off or put the battery back in.... when in magldr the button lights flash repeditally.... I can still flash roms using maglr usb method but when the roms are booted up the button lights are on constantly even in sleep, it seems to recive random input, and you cant put it in sleep mode and when it goes into sleep mode naturally you cant turn it back on........ My first thought was to try and to go back to stock but because I dont have a windows mobile rom on I cant use the active sync method and for some weird reason it wont go to the bootloader(yes I know how to get to the bootloader I am not and idiot)........ so I am stuck and dont know what to do
nchar123 said:
I installed maglar 1.12 on my hd2 using the nbh file method... now my hd2 wont turn off it just restarts as soon as you turn it off or put the battery back in.... when in magldr the button lights flash repeditally.... I can still flash roms using maglr usb method but when the roms are booted up the button lights are on constantly even in sleep, it seems to recive random input, and you cant put it in sleep mode and when it goes into sleep mode naturally you cant turn it back on........ My first thought was to try and to go back to stock but because I dont have a windows mobile rom on I cant use the active sync method and for some weird reason it wont go to the bootloader(yes I know how to get to the bootloader I am not and idiot)........ so I am stuck and dont know what to do
Click to expand...
Click to collapse
what happens when you try to go to bootloader?
Bro, try flashing any windows mobile 6.5.* rom on your hd2..
To do so, enter hd2 in bootloader mode,
Keep pressing DOWN + POWER when device is switchd off initially
and flash any rom.
This will surely help you
orangekid said:
what happens when you try to go to bootloader?
Click to expand...
Click to collapse
Yes what happens when you try to boo into bootloader?
strange mate!!!
when you ask for help be positive!!!!
use wise words....i stood 5 min to reply u or not!!!
because no one is an idiot on XDA,....
flash radio 2.15 first!!!
if ur phone want work
than
flash from SD card your custom rom 6.5 (search for the steps on xda)
your phone want start for sure!!!!!
but you will get back you bootloader back
1-HSPL
2-T29
3-Mag-loader 1.13
4-flash radio 2.15
5-flash your ROM
nchar123 said:
I installed maglar 1.12 on my hd2 using the nbh file method... now my hd2 wont turn off it just restarts as soon as you turn it off or put the battery back in.... when in magldr the button lights flash repeditally.... I can still flash roms using maglr usb method but when the roms are booted up the button lights are on constantly even in sleep, it seems to recive random input, and you cant put it in sleep mode and when it goes into sleep mode naturally you cant turn it back on........ My first thought was to try and to go back to stock but because I dont have a windows mobile rom on I cant use the active sync method and for some weird reason it wont go to the bootloader(yes I know how to get to the bootloader I am not and idiot)........ so I am stuck and dont know what to do
Click to expand...
Click to collapse
People he can not flash anything having to do with flashing via the SPL bootloader, this is why Orangekid and I both asked what happens when the OP trys to boot into bootloader.
calm down everyone!
lol
sorry, like others have mentioned, what exactly happens from start to finish when you try and get in to the boot loader, yes i know you said you know how to do it
but humour us, start to finish, buttons you push, whats on teh screen, everything.
sounds like something in the SPL has been screwed, been a lot of that recently which is a bit odd.
I can not get to the bootloader
I know that I cant get to the bootloader I tried the way you said above again and it just goes stright to magldr so I can not flash back to stock ........ I took it to a phone repair guy who said he fixed it and it appeared like he did but then two hours later it started again .......
Here is a video of my phone
*htt*p:/*/ww*w.y*ou*tube.c*om/watch?v=U7h3flLrE5g** I put the stars because I can post links right now but this is a video of my phone
nchar123 said:
*htt*p:/*/ww*w.y*ou*tube.c*om/watch?v=U7h3flLrE5g** I put the stars because I can post links right now but this is a video of my phone
Click to expand...
Click to collapse
Ok everyone as you can see he can not get the SPL bootloader to come up.
I will help you out with your Youtube link too.
I am very sorry to tell you but without being able to get to the bootloader you can not flash a official ROM back to the HD2 so you can not send it in for warranty exchange our repair. That is unless there is some miracle program out there that you can run from your computer to force the bootloader to bootup, which i have never heard of one. (Note to Devs that would be a awesome program to create if it is possible )
There is the bootloader.exe but you already have to have a Sync type connection for it to work and i don't know if the connection you get using Zune is enough. I attached the a EnterBootloader.zip file but like I said i don't know if it will help you are not. Try connecting and syncing your HD2 with Zune and then try to run the EnterBootloader.exe from your computer and see what happens.
Thanks for the program but when I try to run it in windows phone 7 it gives me the error that it is not a valid windows phone 7
Is there a way I could update or change magldr without the bootloader? or is there any sort of windows mobile rom I could install through magldr like you would with android or wp7?
I mean sorry it gives the are that it is not a valid win32 aplication not windows phone 7 that was a typo
nchar123 said:
Is there a way I could update or change magldr without the bootloader? or is there any sort of windows mobile rom I could install through magldr like you would with android or wp7?
Click to expand...
Click to collapse
Was shocked to watch your video !!
there is no way to flash windows 6.5 roms directly through MAGLDR..
would suggest you to get HD2 to nearby mobile repair center, hopefully they can help you out
Do you know of one around san diego or a place that could do jtag?
nchar123 said:
Do you know of one around san diego or a place that could do jtag?
Click to expand...
Click to collapse
I know someone in that can JTAG your HD2 buit he lives in Texas, but he is very good and experienced with JTAGing HD2s, PM me if you want more info as it would be against the rules for me to provide any other information in the forums.
Also I do not think you need JTAG but just need your voulume rocker fixed, but he is still the guy to do it.
the volume buttons should be easy to test within windows its self
I doubt its MAGLDR issue, it looks like an SPL issue.
could you tell me how much the jtag would cost and the volume down and up buttons work when the wp7 build is up