Related
Hi .my english no good. I upgrading my htc. this file is corrupted . i asked pro . he says your device locked. install USR. i intall usr. next next next... my htc not opening. black screen. i am not open bootloder mode. i am not start hard reset. but i set usb cable and sound come but i am not open bootlodaer. please help me ?
interesting i take out battery. i dont push the opening button . but i set usb cable and sounds hail from computer?? i am not enter bootloader mode.
this error :
you need to enter bootloader before flashing an RUU.
Hold the camera button and reset.
And by the way, your "Pro" obviously didn't know about aserg's method.
I wuz flashing it went to 99% and gave me an error so I reset and it wuz still stuck so I took out the battery and now it won't do anything when I plug it into the pc it says unrecognized usb device is there anyway to get the pc to recognize it so I can fix it any help is appreciated
bootloader
Put it into the bootloader, the PC wont recognize the device until you flash it again, but you should be able to fix it. Get into the bootloader by pressing the power key and the voice commander button (looks like an old tape) at the same time and while holding, press the soft reset button on the bottom. This should put you into the bootloader mode, (the backlight does not light up, it just says bootloader and USB or SERIAL in faint writing depending if you have it attached to your PC)
invoking boot loader
Yes...I had a similar issue yesterday and thought to use the button sequence to force the bootloader. The other thing I had to do was get a flashlight and note the bootloader version of 2.05. I then ran the latest update tool from one of the kitchens and that allowed me to load the image of choice that I placed in the same folder.
how did you do it?
I used UNI_bootloader EXIT.exe to get mine back. same situation, v2.05 bootloader, unplugged at 99%. stuck at v2.05. run the exe, and its fine.
Sadly enough i need to post this.. i have both the 6800 and the 6700, i did the same thing twice ... starting with the 6800, had no problem fixing that one, but the 6700 for some reason after a stock rom flash that didnt take completely its stuck saying Serial (top), 1.00 (bottom) , tried uni_bootloader, tried reflashing, for some reason it cannot catch the device, however, the drivers are loaded just fine, that much i know it worked before. any ideas on how to kick start this thing ( i have no memory card at all in it , havent been able to find a miniSD around here anywhere ). Any ideas would greatly help. Thanks in advance.
Hello!
As title says i bricked my Axon :crying:
I followed http://forum.xda-developers.com/showpost.php?p=68738854&postcount=100 (and the german one that linked to this one) but couldnt do the fastboot unlock.
So i couldnt finish this and my phone required a pin number to start android: bootet and started up but wanted a pin code to start/enter system.
Wasnt able to fix that with googling for answers so i went back to edl mode and rewrote my backup boot/recovery images with axon7backup.
Had no errors with that but it wont start now:
After the ZTE Logo the display goes black but it connects as "handset diagnostic interface (DFU) (ComX)" to my computer.
I fiddled around with driver installing etc and forced the HS-USB QDLoader 9008 on it but no luck, axon7backup/root can not connect.
When i did the actual flashing yesterday it never connected with the hold both vol-keys and connect usb way either, always had to reboot into edl via adb.
I cant boot anything else (no twrp/recovery) it just goes to the diagnostic interface mode.
Thanks in advance
you can try to get into adb mode with this:
- power off your device
- hold the vol down key while plugin in the usb-c cable (connected to your pc)
- keep holding
- you should get a white box with FTM factory test mode
- you are free to use adb again - so you can get into edl mode as well....
for pin part that'S normal while unlocking your device encryption gets deleted and you have to abort and factory reset your device in twrp....
Starvirus said:
you can try to get into adb mode with this:
- power off your device
- hold the vol down key while plugin in the usb-c cable (connected to your pc)
- keep holding
- you should get a white box with FTM factory test mode
- you are free to use adb again - so you can get into edl mode as well....
for pin part that'S normal while unlocking your device encryption gets deleted and you have to abort and factory reset your device in twrp....
Click to expand...
Click to collapse
Thanks. I tried it but it wont go to FTM. Only goes to diagnostic com port.
It seems i cant even turn it off. The little red light on the front is on the whole time .
sadly the disadvantage of a built in battery, so you have to wait till the battery is empty and try my instructions then....if it's not realy off it won't work, the mode you are currently in you usually only reach if you switch it on while holding both volume buttons, the edl mode is sadly not reachable with a key combination directly on G models.
adb don't show your device?
Starvirus said:
sadly the disadvantage of a built in battery, so you have to wait till the battery is empty and try my instructions then....if it's not realy off it won't work, the mode you are currently in you usually only reach if you switch it on while holding both volume buttons, the edl mode is sadly not reachable with a key combination directly on G models.
Click to expand...
Click to collapse
Oh ok. I expected ftm to work from vol-down and power-button till restart.
@adb: sadly no connection possible since it goes straight to Comport Connection.
Edit:
Couldnt make that work. It was off and i connected the usb. So it showed me the loading battery picture where i cant do anything. held the vol-down the whole time. But as soon as it had some battery it went straight to comport-connection again
im sorry to say, but ur device is bricked to a degree where you would need ZTEs Flashtool to fix it. Unfortunately we dont have that tool, so you might have to send it in
i have the same exact problem :'(
Have u been able to fix it?? I'm in a situation that i cant even send it to ZTE to fix it :'(
nsabir said:
i have the same exact problem :'(
Have u been able to fix it?? I'm in a situation that i cant even send it to ZTE to fix it :'(
Click to expand...
Click to collapse
Hi,
couldnt fix it myself so i had to send it in.
Unless some tool/rom was released in the last few months to fix it yourself i would guess your device is bricked.
Hi I have almost the same problem, I tried to unlock bootloader and now I don't have the recovery, I can boot and use my mobile but I can't restore it or update it because I don't have the recovery
I try whit axon7tool to restore the recovery but I got a error.
MaxRink said:
im sorry to say, but ur device is bricked to a degree where you would need ZTEs Flashtool to fix it. Unfortunately we dont have that tool, so you might have to send it in
Click to expand...
Click to collapse
Hi, do you have any idea, if there will be such a flashtool to work with DFU mode? I'm thinking that there are a lot of guys have bricked their devices (including me).
((
Hello, I'm new to xda, in fact I registered just to ask for help. My p9 lite got stuck on huawei logo, when i try to turn off the device it just reboots 2 times and then just stays on huawei logo. I can enter fastboot and rescue mode, but i have not enabled usb debugging and oem unlock on the device earlier. To be honest this is my first android device, in the past i used only windows phones, so you could say i'm completely new to this. Any suggestions on how to recover my phone or flash any rom into it? I'd be very glad if someone helped me find the solution to this problem. Not sure if i made a thread in the correct place, direct me if i'm mistaken
There are few different versions of P9 Lite, look at the back of the phone to the bottom to see the numbers beside VSN and let us know.
1) Also when the phone is turned off plug in the usb to a computer or charging adapter
2) Hold down volume up & power
3) Let go of the power button when you feel the buzz while still holding the volume up button
4) Download latest version & recovery.
5) Go to Settings>Developer Options>USB Debugging On
5B) If you don't see Developer Options in settings, then go to Settings>About Phone>Build Number & ( tap the Build Number untill it unlocks)
6) Update us on the status, hope it works out.
GloryNation said:
There are few different versions of P9 Lite, look at the back of the phone to the bottom to see the numbers beside VSN and let us know.
1) Also when the phone is turned off plug in the usb to a computer or charging adapter
2) Hold down volume up & power
3) Let go of the power button when you feel the buzz while still holding the volume up button
4) Download latest version & recovery.
5) Go to Settings>Developer Options>USB Debugging On
5B) If you don't see Developer Options in settings, then go to Settings>About Phone>Build Number & ( tap the Build Number untill it unlocks)
6) Update us on the status, hope it works out.
Click to expand...
Click to collapse
tried to enter recovery, still not work. can't go to developer options because phone is stuck on logo, can't power off. couldn't find any solution that works anywhere, been searching for more than 6 hours, still no use. phone model is VNS-L21 forgot to mention earlier
What exactly were you doing before this happened and does your computer recognize your phone when plugged in at all.
Try holding volume up & down together & plug phone in when it reboots on you, & report back with what you see. If anything at all.
GloryNation said:
What exactly were you doing before this happened and does your computer recognize your phone when plugged in at all.
Try holding volume up & down together & plug phone in when it reboots on you, & report back with what you see. If anything at all.
Click to expand...
Click to collapse
I tried to install nougat update, computer recognizes it only in fastboot. holding volume buttons haven't changed anything still no progress. the thing is i had installed nougat a moth or so ago and it worked fine, then rolled back to marshmallow and now this. i'm pretty sure i tried to install correct package, because it was the same i had installed earlier
Did you download a adb tool on your computer that have the 'fastboot.exe' file? If so open that folder,
Have the mouse curser hover in that folder, hold down shift & right click the mouse
Open command prompt
Connect phone as is in fastboot mode
Type adb devices & press enter
Type adb continue & press enter
Hi,
I have the same issue as ellanyx.
my phone can only be stucked while booting or if I connect my phone to a computer, I'm able to boot it in fastboot.
as ellanyx, I didn't enable usb-debug nor OEM unlock option...
so when I'm in fastboot, I type the command "fastboot oem unlock xxxxxx" (hopefully the different data needed are the correct ones mentioned on the box of the phone) I get this error message:
C:\Users\Dieu\Downloads\SRKToolHuawei-STABLE-V1.3-20160619>fastboot oem unlock xxxxx
...
FAILED (remote: Command not allowed)
finished. total time: 0.016s
and off course the other options like "fastboot flash recovery recovery.img "... doesn't work.
I can't use the adb commands neither.
when I type the commande, as mentioned above, "adb devices" or "adb continue", nothing works.
So I'm a bit desesperate
do you have any solution for this kind of issue?
thanks
Dude, so the last firmware on your phone was MM or N? If it was MM you should put stock firmware appropriate for your model in dload folder on SD card and put volume+volume-power, and thats it. If you stack on N,....then I dont know because dload method doesnt work with N, or maybe works if you can find stock firmware with recovery for N.
Regards
Unfortunately I can't update with the 3 button update otherwise it would indeed solvemy problem.
pyromana said:
Unfortunately I can't update with the 3 button update otherwise it would indeed solvemy problem.
Click to expand...
Click to collapse
Probably you didnt have correct Oeminfo for MM if dload method didnt work....Try to conect phone with Toolkit and follow procedure for flashing oeminfo and custombin, after that flash stock recovrry and b161 via dload metod. You will find it on forum here.
Regards
the procedure from SRK toolkit?
would it be possible to provide it? because I can't unlock the OEM and I didn't tick the USB debug think.
Maybe problem with the ps not phone so u can not connect with adb
Try with different pc you must have flash oem with fast boot without enable adb from phone if u in fastboot
I can only boot my phone in fastboot (vol- + power) and not in recovery (vol+ + power).
also when using the SRK toolkit, the first screen tells me to be sure that the usb debugging is enable, which I haven't done...
if I'm not mistaken, fastboot is to use the fastboot command and recovery the adb commands
the connection with fastboot works on my computer, the link is made. however when I type the command to unlock the OEM, I get an error stating that the command is not allowed.
when I use the SRK toolkit, with the different questions, he tries to connect the phone with adb and waiting.... waiting...
is there a command to reboot in recovery but from fastboot? in the otherway around it exists but it doesn't seem that from fastboot to recovery it exists.
thanks.
Alexxxx1 said:
Dude, so the last firmware on your phone was MM or N? If it was MM you should put stock firmware appropriate for your model in dload folder on SD card and put volume+volume-power, and thats it. If you stack on N,....then I dont know because dload method doesnt work with N, or maybe works if you can find stock firmware with recovery for N.
Regards
Click to expand...
Click to collapse
dload method works on N. I downgraded my phone from unofficial N update back to official MM update using this method yesterday. You just have to enable OEM at developer options on settings.
It looks like people can't be bothered to read the 1st post properly before they reply.
HE CAN NOT BOOT TO ANDROID SO HE CAN NOT ENABLE OEM OR ACTIVATE USB DEBUGGING!!!!
What he CAN do, is go into eRecovery and Fastboot.
With that in mind, I would suggest using the dload method through fastboot.
Also, make sure it is Huawei SRK Tools 2.0 that is used, as it actually asks if you are in debug mode or fastboot.
Note that there is a few bugs in SRK 2.0:
The TWRP recovery file has the wrong filename in the package, so it WILL fail unless you name it correctly.
Also, when trying to root, do NOT use the "P9 Lite" method as that WILL fail too. Use the "P9/P9 Plus" method.
I am trying to set up a complete guide that can restore the phone when it is stuck in fastboot, however I apparently went a step too far...
ellanyx said:
Hello, I'm new to xda, in fact I registered just to ask for help. My p9 lite got stuck on huawei logo, when i try to turn off the device it just reboots 2 times and then just stays on huawei logo. I can enter fastboot and rescue mode, but i have not enabled usb debugging and oem unlock on the device earlier. To be honest this is my first android device, in the past i used only windows phones, so you could say i'm completely new to this. Any suggestions on how to recover my phone or flash any rom into it? I'd be very glad if someone helped me find the solution to this problem. Not sure if i made a thread in the correct place, direct me if i'm mistaken[/QUOTE
Do you have TWRP recovery ?
---------- Post added at 09:55 AM ---------- Previous post was at 09:50 AM ----------
ellanyx said:
Hello, I'm new to xda, in fact I registered just to ask for help. My p9 lite got stuck on huawei logo, when i try to turn off the device it just reboots 2 times and then just stays on huawei logo. I can enter fastboot and rescue mode, but i have not enabled usb debugging and oem unlock on the device earlier. To be honest this is my first android device, in the past i used only windows phones, so you could say i'm completely new to this. Any suggestions on how to recover my phone or flash any rom into it? I'd be very glad if someone helped me find the solution to this problem. Not sure if i made a thread in the correct place, direct me if i'm mistaken
Click to expand...
Click to collapse
Boot into fastboot mode and flash a custom recovery by meticulus. Link : meticulus.co.vu
Then whenyou get stuck hold power and vol down button for 2 minutes the phone will reboot and then when it says that your device has been unlocked and cant be trusted then only press vol up key ( dont press power button then). The u get into huawei recovery. From that u should power off the phone. Now get a custom rom by meticulus into your device sd card ( Cyanogenmod 13 is recommended ). Then insert sd card in a powered off phone. Now press vol up and power key and flash gapps and custom rom and you are good to go.
Click to expand...
Click to collapse
So, MY question:
I have tried 4 times to get Nougat installed, but every time I got the SMALL package (1.25gb) which means it is not complete.
I decided to try ONE more time, but think I have made a serious mistake.
I was on B161 and tried to downgrade to B160 without upgrading to Nougat first.
This has caused my phone to be stuck at boot with the message "Your device is booting now..."
I can NOT get into eRecovery or fastboot no matter what I do.
If I just leave the phone, then it discharge very fast, but as soon as I plug it in, it starts up and gets stuck at the same screen again.
Does anyone have ANY idea about how I can get out of this problem?
UPDATE:
I have managed to boot to fastboot while connected to my pc.
The phone is unlocked but FRP is LOCKED, which means I can't flash anything.
I read about using Miracle Loader to remove the FRP lock, but it can't "see" my phone. Maybe I am doing it wrong?
SnowmanDK said:
So, MY question:
I have tried 4 times to get Nougat installed, but every time I got the SMALL package (1.25gb) which means it is not complete.
I decided to try ONE more time, but think I have made a serious mistake.
I was on B161 and tried to downgrade to B160 without upgrading to Nougat first.
This has caused my phone to be stuck at boot with the message "Your device is booting now..."
I can NOT get into eRecovery or fastboot no matter what I do.
If I just leave the phone, then it discharge very fast, but as soon as I plug it in, it starts up and gets stuck at the same screen again.
Does anyone have ANY idea about how I can get out of this problem?
UPDATE:
I have managed to boot to fastboot while connected to my pc.
The phone is unlocked but FRP is LOCKED, which means I can't flash anything.
I read about using Miracle Loader to remove the FRP lock, but it can't "see" my phone. Maybe I am doing it wrong?
Click to expand...
Click to collapse
Try to relock and then unlock the bootloader again. And make sure oem unlocking is enabled in dev options
Arsaam said:
Try to relock and then unlock the bootloader again. And make sure oem unlocking is enabled in dev options
Click to expand...
Click to collapse
Please read my previous post again
I can NOT boot normally. And as FRP is locked, then I can't relock or unlock the bootloader.
SnowmanDK said:
Please read my previous post again
I can NOT boot normally. And as FRP is locked, then I can't relock or unlock the bootloader.
Click to expand...
Click to collapse
Go to fast boot mode and from their try to flash meticulus recovery.
You can also try the adb method as well.
Visit meticulus.co.vu
Hey!
Z2 owners that like to mess around with their phones are prone to get f#ked. I was there and I faced the problem some of you probably did - a hard brick. There are a ton of tutorials on how to fix it, but I believe I found a new way that doesn't envolve resetting it. I have only tried with twice on my phone, so I'm really looking forward to know if it's universal!
Scenario - Your phone has a black screen. The notification LED is on. If you hold the power button it flashes the ZUK logo and it vibrates. If you identify with this scenario, go forward!
1 - To turn off your device (if you haven't already), press the power + volume up. The phone will vibrate, flash the ZUK logo, turn off the LED and turn it on again. Continue holding both buttons. When the LED turns off again, REMOVE your fingers from both buttons right away. If done correctly, it won't come back again and the LED will be off
2 - Hold both Volume Up and Volume Down at the same time. Connect to the computer. You should encounter your Fastboot mode (with your baseband and other info blank).
3 - Go to your email and redownload the bootloader unlocker. Yes, remember that file? Use it. You can use one of those unlock bootloader tutorials online, but if you know what you're doing, here's the command:
fastboot -i 0x2b4c flash unlock unlock_bootloader.img
4 - Right after that, run this other command
fastboot -i 0x2b4c oem unlock-go
That's it. You should be able to go to the recovery (flash it again just to be sure). Try it out and tell me how it goes.
not working...phone is gettin turned off...but holding up and down..then connecting is doin nothing..it just keeps on going on and off again
This method worked for me,thank a lot of,great trick
Sent from my Redmi Note 3 using Tapatalk
you my friend, are a god among men, i owe you a beer.
fastboot mode conncted and flash unlockbootloader.img file..but not boot mobile shows error msg .my bootloader is unlocked any suggestion plz
vardhan21 said:
fastboot mode conncted and flash unlockbootloader.img file..but not boot mobile shows error msg .my bootloader is unlocked any suggestion plz
Click to expand...
Click to collapse
Same thing happened to me..followed this link https://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/ as my phone showed 900E mode in Qfil ...followed and unbricked..mine bootloader also showed as unlocked
paps2k3 said:
Same thing happened to me..followed this link https://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/ as my phone showed 900E mode in Qfil ...followed and unbricked..mine bootloader also showed as unlocked
Click to expand...
Click to collapse
hey thnks bro...i successfully enabled 9008 port and flashed firmware
thanku so much
Where were you man I have to cut my wire and format my phone for flashing new firmware
My phone don't show the led light
No button combination works
I was restoring twrp backup and the next boot...And i was bricked
It shows diagnostic mode 900E
Please help
Finally done
vardhan21 said:
fastboot mode conncted and flash unlockbootloader.img file..but not boot mobile shows error msg .my bootloader is unlocked any suggestion plz
Click to expand...
Click to collapse
Had the same problem and first i went to download mode by following the the below link
https://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/
then i downloaded the stock firmware and followed this guide
https://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/
Both of them helped.:good::fingers-crossed: hope they work for you
Please tell me the process for recover from hard brick, because zukfans.eu is no longer available.
paps2k3 said:
Same thing happened to me..followed this link https://zukfans.eu/community/threads/how-to-unbrick-zuk-z2-from-diagnostic-port-900e.2856/ as my phone showed 900E mode in Qfil ...followed and unbricked..mine bootloader also showed as unlocked
Click to expand...
Click to collapse
What is the process??? Please tell me here because zukfans.eu is not accessable
Rit2005 said:
What is the process??? Please tell me here because zukfans.eu is not accessable
Click to expand...
Click to collapse
Hi ..very sorry..not using z2 plus for a long time..I forgot the process what I did..I followed the steps mentioned there.