PLZ help !!
I searched and I tried everything
disabling antivirus, and Windows Firewall , Restarting PC and PPC.
But still giving me the same error.
I update it to Diamond and it's now sticking on boot picture showing diamond with qoute under it " ITs Popa Black Diamond"
and when I press reset soft + Camera button + Power button then shows me Green and Red And Blue screen
I started the ROMUpdateUtility with Rom
after a while shows me this error
UPDATE ERROR 262
Plz Help
This thread should help (it's an Activesync issue).
I didn't know he made Vogue ROMs......
I had a similar problem. I have wanted to update mine ROM. I have downloaded new ROM and Unlocker and used How To Unlock Your Phone And Flash A Custom Rom And Relock Your Vogue (Written by Detroit_Doug). There it is written that the first needed to start RomUpdateUtility.exe, I have made as have been written and then as I did not try I all time had an error 262. When I already used all variants and have helped nothing. Then I have found in a folder with taken Unlocker file Vogue_unlocker.bat. After its start I followed instructions on the screen and all has passed smoothly. Phone has been successfully unblocked and flashed.
Related
Help Help Help
Iam new to the flashing
I have herald (HTC P430 HERA) with wm5 ,i tried to upgrade to wm6 with TOUCH-IT.I installed the SPL and then ran the RUU ,everything was perfect the installation started normally ,durin the installation i chose the option to use the keylock ,when my htc started it kept on asking me the password on the device which i entered but it did not accepted .i kept on trying and eventually took out the battery.When i restarted the device it got stuck on a green scnreen with spl 1.08.0001 and when turned off i tried going in to the bootloader but everytime i run the same ruu it gives me erorr 300 i have tried several times now, donwloaded each and every ruu but all in vain and im in pain .sometime the screen get stuck on 0% . Can somebody help or atleast direct me to the right area.
at least it we could reach 1% rom update can be done
i think we can handle it via bootloader commands
you need to install enablerapi....
.......................
You have to download the official Tmobile RUU (google it), and reinstall it. After that before you try to flash your phone you have to take the Enablerapi cab and put it on your phone. After that do a hard reset. If you dont know what that is by now you shouldnt be flashing your phone. But anyway hold the buttons above the talk and end buttons and press the reset button at the same time. A black screen will come up and ask you to press the talk button (green button), press it and the phone will do a reset. Configure your screen and connect phone to active sync/WMDC and make sure you put the phone in airplane mode. Then run the uspl again and follow the directions on the screen.
Hi!
I have a HTC P3300.
I bought a 4Gb SDHC card, and it won't work. I read at the forum that I would need a different rom, so I downloaded "Artemis_Touch_4.02_Full_with_no_cube", which would have sdhc-support.
Then I executed "STEP 1 - activesync then uspl cid unlocking.bat", that finished ok, and then "STEP 2 - activesync then flash artemis touch rom.bat", which stopped with an error 302.
After a restart all that came up was the boot loader. I then tried to flash the original rom (HTC WM6 Dutch) from the computer, but that ended also in an error.
I tried the SD upgrade (rename .nbh file to ARTEIMG.nbh, put it on a formatted sd-card and load it in my phone), and it finished without errors, saying I should press any key.
After pressing a key, the bootloader popped up again.... :S
Can anyone help me? I have been searching the forum and trying to get my phone to work since 21:00 and I haven't got any progress at all!
well sorry for that
did you tried to make hard reset?
and once i had a completely dead artemis.. no sign of life..but it fixed by the following..(and maybe this may help you cuz the flasheng goes not like usual)
while your mobile is off.. press the record botton and the camera and it should starts with usual sd card flashing.
for me this what happens.
the setup was in three phases as i saw... and it took about 30 mins .
maybe it will works for you
I also tried a hard reset, wouldn't work.
I pressed and hold the camerabutton, but nothing happend...
Maybe the battery is empty, so I pressed and hold the camera button while plugging in the usb-cable.
It started the SD-upgrade, and is still busy.
The update ended with a "press any key to continue".
But when I pressed a key, the boot loader popped up :S
When I tried to flash another rom (NLD-FINAL), an error occurred (I believe it was error 270, not sure).
But then the normal startup screen appeared!
I don't know how, but the problem seems to be fixed!
sorry i mentioned the wronge button before..
try to start flashing by pressing the RECORED button and the power.. while your mobile is off.
and be sure that you copied the original shipped ROM to your device (NOT elese)
As you can see in my previous post, I managed to flash the original rom.
I'm gonna try to upload an other rom some other time...
And with a patch I got the SDHC working too!
Thnx for your help!
y_bother said:
sorry i mentioned the wronge button before..
try to start flashing by pressing the RECORED button and the power.. while your mobile is off.
and be sure that you copied the original shipped ROM to your device (NOT elese)
Click to expand...
Click to collapse
Hey, thanks a lot, I tought, my HTC-Cruise is ready for sending to repair, but with your info, it works again. I could install the WM 6.1 again, after System hangs up while booting every time. He found USB connection on a colored sreen. Thank you very much.
Jupeli
I have rogers htc Touch. after trying unlocking the phone, my phone stopped working i tryied hardware reset it show it format but after that all blank it just dies, if some one can help
can you start your phone?
It power on shows HTC logo then stopped black screen, I tried loading rom after pressing Camera button and power it copy the ROM but still not boot.
Before I tried to do CID unlocking afterwhich the problem starts
Which gold card wont work for you?
Have you tried reading through the tutorials when CID unlock fails?
i tried installing Onyx_utl_4.6 & Tabish_rom_V3.3.6.1
It shows that it installed but not boot,
I can't found link to tutorials when CID unlock fails . Can you please send me Link
Thanks for you time and help
Hi to all ,
I have the msn account:[email protected] .Once again,just to make the resume of the whole story if I remember well:The trinity was with the initial sfr 300+ software(wm5);I installed the oli1.20 flashed it with some other ROM software,did not like it and returned to the original one.Then I tried to flash it with the ROM software where all went wrong...After 1 % the screen went blank and all I can do with the device is to put it into the boot-loader mode where it says:
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
When I extracted the file,I discovered that it has 2 nbh-files.I think that is the reason of my defete.Afterwords I have tried all sorts of the first aid solutions : splxploit-windows cannot connect to the device;it says that there is no WCEUS-file and therefore it cannot continue.I have tried to re-flash it through the sd-card:I re-formatted the card on fat32,without any name,put the original ROM and tried to let it boot that way.No success,it marks:loading ... and after 3-4 secs it returns into the boot-loader mode with the same message mentioned above ...
Salutations frm Luxembourg , Goran Stevanovic.
Thx all of ya , problem solved.
sir me too have same probelems, but ma 2 htc trinity dnt stuck at bootloaders, its to to operator logo and stuck there, i have 2 phones with this probelem.
please help me to solve this probelem sir.
gurnek said:
sir me too have same probelems, but ma 2 htc trinity dnt stuck at bootloaders, its to to operator logo and stuck there, i have 2 phones with this probelem.
please help me to solve this probelem sir.
Click to expand...
Click to collapse
1: Boot into BL (camera + power + reset hole)
2: Download the GPS enabled ROM from HTC Support, NOT from a rapidshare/megaupload/4shared etc.. mirror.
3. Flash the ROM, but use the hardspl flasher.(For some reason, it doesn't go error 270 if I use this flasher).
4. Hard Reset again.
Hello,
I have a HTC P3600 and after i make a hard reset the screen goes all black, i already try flash the phone but don't result.
If i try to make a hard reset again the screen shows "press ok to make hard reset" after that goes black again.and its completing %100 but when i want restart its still doesnt work just black screen. just working light =(
So i think not display problem.
Any solution? help me plss
Any chance of sharing the solution, guys, my SPV M700 has similar problems. I tried to flash it with the TRIN-SSPL rom, but it kept saying I need a newer version of the update software.
Now all I have is it gets stuck on the green Windows load up screen and when I reset (Camera-PWR Button-Reset) it goes onto the bootloader tri-color screen, similar to what Goranchen had on his. What do I do now, I would really like to use the phone on another network, and I have looked after it really well, I think, so would be a shame to throw it away. Please help!!
Hi guys, I just got an HD2 and I am new to flashing ROMs on it, but I am not really a beginner because my previous phone was an ETEN x500 and I flashed a ton of ROMs successfully on that phone. However on this one I am running into a problem.
I successfully installed the bootloader HSPL without any problems. Then, I wanted to do task29 before I installed a new ROM. I followed all the instructions fine, I click NEXT until the device enters bootloader mode, then I see a black loading screen on my HD2 with the HTC logo on it. The problem is the loading bar stays at 0% no matter what I do, it won't install the ROM. After about 5 minutes it gives me the following error message:
www . screensnapr . com/u/icpiuj.png
When I click on the "View Document" button, I get the following message:
www . screensnapr . com/u/dhiria.png
(it won't let me post offsite links to images because I only have a few posts, but I mean no harm with them, I'm just trying to explain my problem. )
I have tried uninstalling ActiveSync and reinstalling, changing USB slots on my PC, I removed the microSD card and the SIM card, I tried entering bootloader mode manually and then running task29, but it all fails with the same results.
The phone still works fine, I disconnect the USB cable from the phone after the flashing failed, and remove the battery for 3 seconds and then the phone starts fine with the original ROM. So there is nothing wrong with it.
What could be the problem please?
Thanks for your help.
Hi everyone, sorry for doubleposting but I have found my solution. I had an incorrect HSPL version installed somehow, although I did follow the tutorial here: forum.xda-developers. com/showthread.php?t=653614
I downloaded the HSPL version linked on that thread and it didn't work.
Then I downloaded the one I found here that said specifically for TMobile HD2: www .mobileunderground. info/showthread.php?t=7997&highlight=HSPL+1024%20..
and this one worked great. I have my custom ROM running now.
HSPL3 is the latest and can be found here somewhere. You must not have had SPL 2.10. Glad you got it to work!