Related
My exec just came back from repair!
and found some problems
my ok button doesn't work at all...
i have to click on the x button on the display in order to close the app....
also my startup, ie, message and contact button doesn't correspond to what they been printed....
how can solve this problem?
they replace a new device for me...
is it the problem with the hardware?
like some kind of wiring ir circuit goes wrong?
or i can fix it by editing the registry?
any thoughts is apreciated!
thanks!
Maybe it is configured under a different language?
What was your original ROM language (the language of your keyboard)
tried to update with the different rom version....
still no change!
parkertseng said:
tried to update with the different rom version....
still no change!
Click to expand...
Click to collapse
I was referring to a ROM with a diferent language. Not just a different vrsion of rom. Well, maybe that's what you did. SOrry it didn't work out for you.
Goodluck in finding other solutions
did u install wisbar lite?
nope!
does that help?
nope because i thought u did
when i installed wisbar lite, my OK button did not work and after removing it, it works alright now.
what tasks management programme did u install?
Reading the top line of the OP, I think the repair wasn't as successful as you would have hoped, sounds like a problem with the keyboard itself.
Hi Guys
I've been reading this forum for two days now, and still haven't found the answer to my solution.
I used Olipros unlocker on Saturday, but after step 1 the screen went black and it wont reboot.
I can get into bootloader (by pressing the camera button and the reset pin at the same time), but I can't install the OS from Activesync as the PC can't see the ameo.
I can also get to factory reset (by pressing the volume slider down and powering up), but I haven't done anything in there.
The bootloader shows Olipro SPL 1.2
At the same time as getting this sorted I thought I'd upgrade to WM6 from the posts that are here, but I can't find at all, how to get the ROM onto the ameo without Activesync seeing it.
Can someone point me in the right direction please?
Thanks for any help in advance.
Joe
i have had the same problem.
i solve doing this :
1rst enter in bootloader mode ( Reset + camera button )
plug your USB cable
and flash WM5 or WM6 rom with flash utility
utilies doesn't trcognize your current rom etc but donc care about
then after flash 100% my athena (HTC advantage boot up normaly again)
i hope my experience help you
Hi, thanks for your advice:
Here's what I'm doing:
Bootloader (Camera and reset hole)
Bootloader shows ATHE100
SPL-v1.20. Olipro
USB
I'm then running mtty tool and can get a connection with:
Cmd>
I type Task 32 and it states Level=0
do I then use the lnbs command?
I'm sorry, I dont see what to do now
You state to upgrade ROM with flash utility, but whats the flash utility?
Is it Mtty?
Or another tool that I haven't got yet?
I have downloaded the ROM update tools, and within the rar files there are apps like, enterbootloader, ruugetinfo, rapitool, etc, but they wont run, they say that they aren't a valid win32 application
Sorry, I know my phones not knackered, just don't know how to get out of it.
Joe
run ROMUpdateutility.exe provided with WM5 rom update or WM6 rom update (if you don't have look at XDA ftps ...)
Thank you so much for your help, got WM6 running on it now, everything's v good.
Cheers
Joe
i'm happy you ameo up and alive
seosamh1973 said:
Hi Guys
I've been reading this forum for two days now, and still haven't found the answer to my solution.
I used Olipros unlocker on Saturday, but after step 1 the screen went black and it wont reboot.
I can get into bootloader (by pressing the camera button and the reset pin at the same time), but I can't install the OS from Activesync as the PC can't see the ameo.
I can also get to factory reset (by pressing the volume slider down and powering up), but I haven't done anything in there.
The bootloader shows Olipro SPL 1.2
At the same time as getting this sorted I thought I'd upgrade to WM6 from the posts that are here, but I can't find at all, how to get the ROM onto the ameo without Activesync seeing it.
Can someone point me in the right direction please?
Thanks for any help in advance.
Joe
Click to expand...
Click to collapse
Just out of curiosity, did you take your storage card out before you began the unlock?
not for me : no SD card , only microdrive
Nope, didn't realise I had to....
Is that the common factor in it failing?
Joe
seosamh1973 said:
Nope, didn't realise I had to....
Is that the common factor in it failing?
Joe
Click to expand...
Click to collapse
I don't think so, I don't have a memory card on my Ameo and had the same problem.. And when I told the Olipro **** that I got the black screen AND his SPL was flashed successfully, he kinda went frenzy about "IT IS NOT MY FAULT, IT IS YOURS! YOU ARE STUPID, I AM GOD!".. Nice support, huh?
Donate the mofo!
yes nice support indeed
TryOG said:
"IT IS NOT MY FAULT, IT IS YOURS! YOU ARE STUPID, I AM GOD!".. Nice support, huh?
Click to expand...
Click to collapse
I suggest people read the forum thread, I've been aware of the problem since day one after xmen's pda reset itself while running an unpatched SPL.
clearly you're a moron, or your english is ****, possibly both.
Olipro said:
I suggest people read the forum thread, I've been aware of the problem since day one after xmen's pda reset itself while running an unpatched SPL.
clearly you're a moron, or your english is ****, possibly both.
Click to expand...
Click to collapse
This guy refers to you...
Pantaloonie said:
I'm glad i'm not the only one who feels that way.
The man is obnoxious, arrogant and rude.
But hey - it's a public forum, he can say whatever he wants - as can I.
Click to expand...
Click to collapse
Just don't flame "stupid" people. And if someone asks for help: ignore, say that you won't help them or help them properly (without flaming).
Thnx.
And another thing.
You look *smart* and *cool* when you flame other people when they get problems and ask for help!!! (not)
OK... there's nothing I can do about it, if it black screens, please go and flash a ROM with an OS on it.
until I get hold of a new SPL, I do apologise for this unknown bug, but again, as I said, it's an intrinsic problem of 1.10.
Flash a ROM if it happens to you and it'll be fine. your device will NOT be bricked.
Olipro said:
OK... there's nothing I can do about it, if it black screens, please go and flash a ROM with an OS on it.
until I get hold of a new SPL, I do apologise for this unknown bug, but again, as I said, it's an intrinsic problem of 1.10.
Flash a ROM if it happens to you and it'll be fine. your device will NOT be bricked.
Click to expand...
Click to collapse
Thank you for this friendly answer... (I mean it)
Olipro said:
OK... there's nothing I can do about it, if it black screens, please go and flash a ROM with an OS on it.
until I get hold of a new SPL, I do apologise for this unknown bug, but again, as I said, it's an intrinsic problem of 1.10.
Flash a ROM if it happens to you and it'll be fine. your device will NOT be bricked.
Click to expand...
Click to collapse
Better,,, and sorta friendly.
What do you think about this little gem:
Pissed off == no reply @ the forums.
Cooled down == yeah, ok I can reply.
But then again, what do I know, eh?
Some people PAID you to hack/crack/mangle/otherwise play around with a Athena.
No, I didn't use any of your programs... I have had an unlocked Athena since day one. No, I will wait for the official Dopod release on the 20th (hopefully). If I see any bugs, HELL YES I will query the collective hive mind here.
But please, lay off the "I'm better than you" attitude. It doesn't do any good at all.
Olipro said:
OK... there's nothing I can do about it, if it black screens, please go and flash a ROM with an OS on it.
until I get hold of a new SPL, I do apologise for this unknown bug, but again, as I said, it's an intrinsic problem of 1.10.
Flash a ROM if it happens to you and it'll be fine. your device will NOT be bricked.
Click to expand...
Click to collapse
TryOG said:
Thank you for this friendly answer... (I mean it)
Click to expand...
Click to collapse
Alright guys! I do believe we can start all over, be nice & make progress! Let's try to enjoy our devices and appreciate each other.
Abram said:
Alright guys! I do believe we can start all over, be nice & make progress! Let's try to enjoy our devices and appreciate each other.
Click to expand...
Click to collapse
Yeah, let's bring the '70s back
TryOG said:
Yeah, let's bring the '70s back
Click to expand...
Click to collapse
70's ? you're a decade too late there...
fards said:
70's ? you're a decade too late there...
Click to expand...
Click to collapse
The 70's songs are less worse...
after flash a rom worked for 2 hours normal then the touch screen dead ??? any body can help me with that please ,, sorry for my bad english
What rom?
Try hard resetting or reflashing the Rom
thanks
duprade said:
What rom?
Try hard resetting or reflashing the Rom
Click to expand...
Click to collapse
thanks for the answer but i tried to reflash the rom and hard reset but with no results, i think its a hardware problem ?????
I had a wing and the touch screen stopped working on it for no reason... so it may be hardware
duprade said:
I had a wing and the touch screen stopped working on it for no reason... so it may be hardware
Click to expand...
Click to collapse
and did you fix it ??
did you put a new touch screen protector?
have you tried to flash a different ROM?
if it's a hardware problem, then you might have to send your phone to service center...or install new lcd touch screen by yourself
tareq557 said:
and did you fix it ??
Click to expand...
Click to collapse
no, I had to get it replaced.
mv3 said:
did you put a new touch screen protector?
no i didnt
have you tried to flash a different ROM?
yes i tried but still not work
if it's a hardware problem, then you might have to send your phone to service center...or install new lcd touch screen by yourself
Click to expand...
Click to collapse
yes i think its a hardware problem
Hi All,
I'm pretty happy with the stock ROM (with tweaks) at the moment but I would like to know if its possible to get rid of the TMO branding that appears on boot or when you switch the phone off?
TIA
Thread Moved. Not rom development.
mobi said:
Hi All,
I'm pretty happy with the stock ROM (with tweaks) at the moment but I would like to know if its possible to get rid of the TMO branding that appears on boot or when you switch the phone off?
TIA
Click to expand...
Click to collapse
flash a splashscreen, just like flashing a rom, but no hard reset required.
HERES one
Thanks Sam. I just installed one but I still get the annimated tmo get together crap before the newly installed one opens. Do you think its something I'm doing wrong?
mobi said:
Thanks Sam. I just installed one but I still get the annimated tmo get together crap before the newly installed one opens. Do you think its something I'm doing wrong?
Click to expand...
Click to collapse
i suspect you installed the cab, not flashed the bootscreen, , , , its a multi image process, first the bootscreen, then the roms loading animation, then the welcome screen, and you only need to change the bootscreen, which is an nbh file, the other two parts are cabs.
You need the first part, the HD2 Splash Screen V2.zip from part A
actually, ive just thought, i havent read anything from tmous users flashing splash screens, i doubt theres a difference, but maybe best to hold off, , ,, please be careful!
Cheers Sam!
mobi said:
Cheers Sam!
Click to expand...
Click to collapse
no problem, ,, is that 'cheers i flashed it and it works', , or 'cheers for the warning i wont bother for now'
cos if you have flashed it, id be interested in confirmation that it works. (Cant see why it wouldnt, but ...)
Hey Sam, it works perfectly. That said, now I need to find a solution to the tmo goodbye annimation when you turn the thing off!
mobi said:
Hey Sam, it works perfectly. That said, now I need to find a solution to the tmo goodbye annimation when you turn the thing off!
Click to expand...
Click to collapse
good to hear. no clue about the shutdown, sorry.
samsamuel said:
good to hear. no clue about the shutdown, sorry.
Click to expand...
Click to collapse
The shut down can be changed by a reg setting like the boot animation by looking here HKLM\Software\HTC\HTCAnimation and look for shut down gif
Hello,
After messing the devices whatsoever!
i want to do a fresh start, clean install !
i've downloaded the full rom last december...
Started back in fastboot and flashing, but the boot doesn't work...
i guess i'm missing something in the install... still some slots A and B etc etc
What would be the best way to make a fresh start ? should it be slot A or B ?
because for the moment, i cant restore my device
Flash the newest available firmware with MiFlash tool selecting "Clear all" in the bottom right corner.
fosco_ said:
Flash the newest available firmware with MiFlash tool selecting "Clear all" in the bottom right corner.
Click to expand...
Click to collapse
did that ! but touchscreen or keyboard doesn'work
STEKAM said:
did that ! but touchscreen or keyboard doesn'work
Click to expand...
Click to collapse
Really bro? Do you know how to flash the ROM properly? If not you're being a complete a**hole as people will put their resource on that problem just because you don't follow the flash instructions properly. You're issue is really weird and shouldn't be occurring at all, maybe that's a hardware issue or some of the image files of the Stock ROM you download must be corrupt.
Hello EdWin
Thanks for the very nice answer. Its a pity you lost that much time for such an idiot answer
I've been flashing phones since first release of android and no phone has ever been bricked...
- So yes i know how to flash a rom...
Lately i've notice the android structure changed, talking about slots... Which i dont know very well...
- sorry being an asshole but I wanted to have an input on how to do a clear fresh start...
- concerning my issues... Confirm this is happening... On the October update i dont have any issue... And on December update touch screen is not working well, it work once after i shut down the screen and put it back on...
Unless you have anything constructive i suggest you dont loose anymore time to make stupid answer !
STEKAM said:
Hello EdWin
Thanks for the very nice answer. Its a pity you lost that much time for such an idiot answer
I've been flashing phones since first release of android and no phone has ever been bricked...
- So yes i know how to flash a rom...
Lately i've notice the android structure changed, talking about slots... Which i dont know very well...
- sorry being an asshole but I wanted to have an input on how to do a clear fresh start...
- concerning my issues... Confirm this is happening... On the October update i dont have any issue... And on December update touch screen is not working well, it work once after i shut down the screen and put it back on...
Unless you have anything constructive i suggest you dont loose anymore time to make stupid answer !
Click to expand...
Click to collapse
Please post your touch screen model
Just dial (on November Rom that seems to work for you) *#*#6484#*#* and select version info
jack_21 said:
Please post your touch screen model
Just dial (on November Rom that seems to work for you) *#*#6484#*#* and select version info
Click to expand...
Click to collapse
Hello Jack, thanks foir the answer...
what i find here is that info : LCD : GFF,vendor:tianma,ICtm1911(focal)
does that speak to you ?
thanks
STEKAM said:
Hello Jack, thanks foir the answer...
what i find here is that info : LCD : GFF,vendor:tianma,ICtm1911(focal)
does that speak to you ?
thanks
Click to expand...
Click to collapse
You have to post TP info, not lcd
STEKAM said:
Hello,
After messing the devices whatsoever!
i want to do a fresh start, clean install !
i've downloaded the full rom last december...
Started back in fastboot and flashing, but the boot doesn't work...
i guess i'm missing something in the install... still some slots A and B etc etc
What would be the best way to make a fresh start ? should it be slot A or B ?
because for the moment, i cant restore my device
Click to expand...
Click to collapse
Have a look at my guide over here: https://forum.xda-developers.com/mi-a1/how-to/ota-official-fastboot-image-n2g47h-7-12-t3728929
It should answer all of your questions and it includes the proper batch/ shell script files which automate the flashing for you straight away.