Today I noticed that my 8525 has a weird red tint on the screen whenever I close the keyboard. On the right hand side of the screen, there is a line, and everything to the right of the line has a weird red tint. If I open th phone slowly, the line dissapears at the same rate that i'm opening the phone. It almost seems like something underneath the screen is... pushing on it from below or something? Just a guess. Also the screen's alignment pretty much doesn't work at all anymore, like its the curser will either be on all the way to the left, or all the way to the right. never where i am pushing. Quite annoying.
Thanks for any help!
Me Too!
The same exact thing is happening to my phone too. Sometimes when I slide it back and forth a lot it will dissapear but come back again later when I move the slider. It appears when the slider is slightly off of the closed postition. It never appears when it is open. I think it may have too do with the cable being loose between the main body and the upper screen part or the magnet which detects the slider postition is interfering with the LCD. Any solutions yet?
Related
I dropped my phone and the screen now doesnt respond properly: The hardware DID successfully upgrade to the XDA ROM. But touching it causes the backlight to go on, - but most of the keys dont do what one would expect them to do: The phone turns on with a reminder from the calendar on the screen which wont DISMISS or CLOSE. Pressing on the windows logo and then on the phone key causes the calendar to come up and I am not sure which numbers are entered when I do manage to get the phone to come onto the screen (none of the right hand numbers seem to work at all). Does anyone recognise these symptoms and/or could they just show that my SX-56 needs the ROM RE-flashing? I should add that pressing the Master Reset button with this ROM in place seems to make the phone shut off and then when you restart it, all of the data remains in place. I wonder if there is any possibility that the XDA ROM has prevented the reset button from working normally?
A user on another forum said that to him, '"Sounds like the digitiser is up the swanee - have you tried recalibrating it?"
10-12 vertical black lines started appearing to the right hand edge of the screen. Sometimes they are there, sometimes not. THere is usually at last one there somewhere. At about that time the screen stopped responding as I mention. Today the left third started displaying the same veritcal lines, though spaced quite far apart (about a millimetre). Screen doesn't APPEAR cracked: Does this sound like a digitiser and if so, how do you recalibrate it please or is there a link to somewhere on the XDA site which I cant find which might tell me? Or could it be the cable is loose in the circuit board? As you touch the lower right hand corner of the metal casing where the vertical lines are, those lines flash (the right 10 or 12) on and off. And every coloured bar everywhere on the screen or word of text has vertical lines on it (the white parts don't)??
Someone on ebay has said that his phone "fell from my pocket and onto the carpet and the screen cracked, I then used it for about a week" "I sold the screen to someone cause the wanted the touch pad part of the screen for there phone". and wonder what it was he sold or which part can be replaced on it? IS there a touch part and a screen part on this phone?
To be honest, itsounds like you have brocken a connection somewhere between the LCD and the gfx output, probably not possible to repair yourself.
I wonder where the break would be?
I thought that might be the case: I wonder if it would be worthwhile trying to get another screen?
I should probably try to take the unit apart and see if some break somewhere can be identified if it is a break as opposed to some electonic part having failed. It SEEMS to be in the lower right hand corner?
I took apart my tytn, including the screen part.
After reassembling it, I've had random issues related to the keypad and screen.
By keypad, I mean all the keys on the screen part of the phone (D-pad, call/hangup,soft left/right, Internet Explorer & Email).
They will randomly cease working and randomly restart working (usually after turn on/off the screen with the power button)
The screen will also randomly turn white and come back on only if I turn off the screen and then back on.
Im thinking it has to do with a loose connection somewhere in the screen section of the phone, however, Ive taken it apart 2 more times to check everything out and the problem persists.
I wonder if anyone experienced the same thing and found which specific internal is the issue.
i would like to know too cause my buttons just stopped working. so the talk, end, message, Internet explorer, ect. but the left down up right and center button work.
I have the exact same issue.
All the keys (not keybord keys) randomly stops working. I am so used to it now, that I dont even try to answer the phone with the green key button.
The screen fades to white, sometimes (maybe 1-3 times a day).
The screen is white when awakening from "sleep mode", turning on and off the screen fixes that after a while (50% of the time white screen when from sleep mode).
I have found out that putting a finger nail between the keyboard and the screen, on the right hand side, when in closed position, and then putting the screen back on, gives me a 99% chance of funktional display.
The problem also accurs in the "full keyboard position", But putting the finger nail in the same spot helps.
So I think the problem of the connection is in the keyboard part of the phone, since those slide contact always are on the right hand side, and the display contact shift side.
I would lite to know if any body have a permanent solution for this.
(I have now opend my phone yet, and I have tryed the putting thin plastic between the display and the cover, with minimal success)
thanks for your time
alkizmo said:
I took apart my tytn, including the screen part.
After reassembling it, I've had random issues related to the keypad and screen.
By keypad, I mean all the keys on the screen part of the phone (D-pad, call/hangup,soft left/right, Internet Explorer & Email).
They will randomly cease working and randomly restart working (usually after turn on/off the screen with the power button)
The screen will also randomly turn white and come back on only if I turn off the screen and then back on.
Im thinking it has to do with a loose connection somewhere in the screen section of the phone, however, Ive taken it apart 2 more times to check everything out and the problem persists.
I wonder if anyone experienced the same thing and found which specific internal is the issue.
Click to expand...
Click to collapse
These are the exact symptoms of the "SCREEN FADING INTO WHITE" problem. See this thread for more info: http://forum.xda-developers.com/showthread.php?t=303872
The common causes for this are a bad connection to the D-PAD controller PCB (in the technical manual they mention it should be carefully checked and the really small screews with same torque making a 90 degree with the PCB), a bad controller (that was my case, had to order a new one) or not enough pressure on the square black chip on controller (some people seem to have fixed it by putting a plastic sheet in between the chip and the case, to apply constant pressure).
I suggest you try to re-open your phone and reconnect the D-PAD PCB as carefully as you can, double checking the connection and the screws there.
I did fix my problem, by ordering a new PCB and replacing the old (probably bad) one. It started to happen after I dropped my phone and it's the only thing that worked. Now my phone is as good as new.
Hope this helps!
Similar Issues with screen
I have similar issues;
Anything thats on the foreground gets closed by the 'x' button and if I slide it open the start button gets continually pressed!
Seems to be the top right corner of my TS thats at fault
sometimes it's fine....most of the time its not!
Andy.
I have the same! I have a huge dead spot in the middle of my (Tytn) screen, and if you tap there it actually activates the "ok" in the top right corner. The rest of the screen works ok. Whilst drawing in notes any drawing near the center dead spot results in a streak to the top right hand corner...
Bad screen?
Bad rom?
Bad motherboard?
lepic2019 said:
I have the same! I have a huge dead spot in the middle of my (Tytn) screen, and if you tap there it actually activates the "ok" in the top right corner. The rest of the screen works ok. Whilst drawing in notes any drawing near the center dead spot results in a streak to the top right hand corner...
Bad screen?
Bad rom?
Bad motherboard?
Click to expand...
Click to collapse
You can rule out the ROM and M/board in my view for this specific problem. Your issue is very similar (and I think has the same cause) as those who find programs close randomly when in portrait mode and when they open the keyboard the start menu often pops up untapped.
I think this is just a case of a bit of pressure being put on the screen top right corner. Some folks have tried the business card run around under the bezel fix and had some success others have had to return for replacement/repair.
Some have taken the device apart and removed the gasket around the screen under the bezel, but this is not guaranteed to work.
Others have replaced the screen and for this particular problem it is very rarely successful as the screen is not normally damaged.
If you have a warranty use it - all of the above "fixes" are warranty voiding.
Mike
Hi Mike
It's an interesting problem as when performing a click and drag in Notes (drawing mode) the center section of the screen seems to work normally - a square box can select an area right through the middle of the screen - suggesting that the screen (as you say) is OK. So what is causing the a tap in the middle of the screen to register in the top right hand corner, when we now know that the center of the screen can work and respond in the correct manner. The size of the affected area is about the size of a thumb print EXACTLY in the middle. Personally I would like to believe that performing screen alignment 4 - 5 times a day for the past year has worn out the center dot and that is affecting the surrounding area. The trouble is that this fault has been reported on this site a few times now, and everyone says it's caused by something else! What did I do immediately before this happen I hear you ask? I flashed a new radio rom and was fiddling with a piece of card I have wedged down the RHS side of the screen to try and help stabilise the screen alignment. Since this problem arouse, I have removed the gasket - but that hasn't fixed it. I'm going to try and boot up the phone out of the casing to see what "zero" pressure applied to the screen does.
I'll report back...
Lepic.
lepic2019 said:
Hi Mike
It's an interesting problem as when performing a click and drag in Notes (drawing mode) the center section of the screen seems to work normally - a square box can select an area right through the middle of the screen - suggesting that the screen (as you say) is OK. So what is causing the a tap in the middle of the screen to register in the top right hand corner, when we now know that the center of the screen can work and respond in the correct manner. The size of the affected area is about the size of a thumb print EXACTLY in the middle. Personally I would like to believe that performing screen alignment 4 - 5 times a day for the past year has worn out the center dot and that is affecting the surrounding area. The trouble is that this fault has been reported on this site a few times now, and everyone says it's caused by something else! What did I do immediately before this happen I hear you ask? I flashed a new radio rom and was fiddling with a piece of card I have wedged down the RHS side of the screen to try and help stabilise the screen alignment. Since this problem arouse, I have removed the gasket - but that hasn't fixed it. I'm going to try and boot up the phone out of the casing to see what "zero" pressure applied to the screen does.
I'll report back...
Lepic.
Click to expand...
Click to collapse
It will be interesting to see what results you get. You'll need the old rubber band technique to hold the battery in place while you do it!
Mike
Well it's not due to the case squishing the sides of the screen as I just dismantled my hermes, wired it all up in bits on my desk, powered it up and still the screen has a dead spot in the middle and phantom taps in the top right. Temperature is normal room temp, approx 22deg c today.
I'm not sure the exact mechanisms of how these touch screens work out where you are tapping (resistance, voltage), but it looks like there are 3 separate strips running around the screen. 1 goes straight across the bottom, two goes up the LHS and across the top and 3 goes up the RHS. Therefore there is a gap between strips 2 and 3 in the top RH corner. Coincidence? hmmm It seems to me for it to register a tap in the top RH corner, strips 2 and 3 would register low voltages (or high resistance) and bottom wouldn't register at all. Thus suggesting a fault with the PSU that powers the touchscreen. Taps near the edges work because they are near the edges and therefore the resistance is not too great and can be detected, taps in the middle and worse off because they are far from all the detecting edge strips.
Does anyone think that there might a registry tweak for boasting power to the touchscreen?
Hermes Whie Screen Problem
To fix the "white screen" problem, you have to take your unit apart, and reconnect the ribbon cable.
I have a new 8525 and it started happeneing to me, so I took it apart this week, and reseated the ribbon connector.
Fixed the problem.
Has anyone here read and understood all that is said here:
http://msdn2.microsoft.com/en-US/library/aa919680.aspx
Perhaps someone could compare the touch.dll in Black Majik to WM5 - should be the same right?
How come that HKLM/hardware/devicemap/touch doesn't show the touch.dll driver as drivername? Keyboard has it's driver...microsoft says it should say drivername = touch.dll
Do you all have that in your registry?
I have read a few posts about the white screen issue and some seem to pertain to my problem and others don't. My screen is white 100% of the time from power on to power off. So I can't seen anything when it first boots or comes out of standby mode or any thing else. The only way that I can get the screen to be anything but white, is to hold it in my left hand with the keyboard slider bottom left corner of the phone pushed up against the base of my thumb muscle and my other fingers pushing on the bottom right corner or the phone on the screen slider. Sometimes if I hit it in the bottom right corner then squeeze it I can get it to work without tiring myself out from squeezing after 1 minute.
Seems to be a pressure and angle thing i think. The phone has been dropped on more than one occasion. Ten tops. Sometimes when I squeeze it i get lines from left to right, then fade to white.
If I put the phone on 65-90 degree angle from my eyes I can see a little black mark at the top of the screen under the C of HTC. That is what had me thinking that it was a cracked LCD.
Any help would be greatly appreciated. Phone is still under warranty, but would rather not be without it for the 6 -8 weeks I was told it would take, only to find out it was a cracked lcd and they won't fix it.
I believe you have to open it. Try to connect every single connection again.
I Had This
I had this problem when i dropped my Vario 2 the screen cracked and was all white, when i went on ebay and bought a new screen I took the vario 2 apart and replaced the screen BUT the ribon connector that plugs into the board was not quite in so when i re-assembled it i just got power and white screen.
There are a couple of little lugs on the ribon cable and i though that once they were butted up to the connector on the board that it was in properly. BUT the lugs actually needed to be pushed that little bit further and slide under part of the connector. BANG it worked fine.
bmaffin13 said:
I have read a few posts about the white screen issue and some seem to pertain to my problem and others don't. My screen is white 100% of the time from power on to power off. So I can't seen anything when it first boots or comes out of standby mode or any thing else. The only way that I can get the screen to be anything but white, is to hold it in my left hand with the keyboard slider bottom left corner of the phone pushed up against the base of my thumb muscle and my other fingers pushing on the bottom right corner or the phone on the screen slider. Sometimes if I hit it in the bottom right corner then squeeze it I can get it to work without tiring myself out from squeezing after 1 minute.
Seems to be a pressure and angle thing i think. The phone has been dropped on more than one occasion. Ten tops. Sometimes when I squeeze it i get lines from left to right, then fade to white.
If I put the phone on 65-90 degree angle from my eyes I can see a little black mark at the top of the screen under the C of HTC. That is what had me thinking that it was a cracked LCD.
Any help would be greatly appreciated. Phone is still under warranty, but would rather not be without it for the 6 -8 weeks I was told it would take, only to find out it was a cracked lcd and they won't fix it.
Click to expand...
Click to collapse
Either send back and keep warranty or try the several solutions posted. I myself am pretty sure I found the correct solution and I posted it in the appropriate thread.
Thanks guys, I think I'm going to try my luck with sending it in. Will probably add a link to the main whitesrceen thread so hopefully I get no hassles. Will post back When I get it back.
I had a similar problem and voided my warranty because I don't have a spare device... anyway, here is where I found my solution.. http://forum.xda-developers.com/showthread.php?t=321163
Good Luck... My phone is still working fine....
As a fresh owner I have a few questions:
1 - The lower right corner of the front panel wobbles (?), moves slightly on touch, I can press it for about 1mm (see the attached screen). It is especially annoying when pressing OK or dial off (or whatever the button is called). Is it normal?
2 - The screen has a slight green tone (hue), can anything be done with it?
3 - LCD has noticeable light leaking near the bottom side, again, is it normal? (Well, the screen does not work now anyway, gotta flash the phone.)
Thanks
Biges said:
As a fresh owner I have a few questions (too lazy to search):
1 - The upper right corner of the front panel is flimsy (?), moves slightly on touch. It is normal?
2 - The screen has a slight green tone (hue), can anything be done with it?
3 - LCD has noticable ligh leaking near the bottom side, again, is it normal? (Well, the screen does not work now anyway, gotta flash the phone.)
Thanks
Click to expand...
Click to collapse
(1) I have no issues with this, seams fine on mine
(2) I cannot notice any hue, maybe you have a faulty unit given the blue colour and the movement of the panel.
(3) Yes LCD light is noticible, I also get leaks through the optical pad when I have the notification LED's on
1. I got some small loose on the front pannel upper area, it's especially felt when You hold the phone in one hand and work with Your thumb pressing the screen or just put the phone to You ear. You feel then the pannel moves a bit down. Maybe thats normal or just the build quality is not so good at all.
sounds like you have a faulty one. mine is solid as a rock. the loose screen and the green hue could be related. there shouldnt be any discolouration at all and i can only see it getting worse to be honest. where did you get it? if its somewhere reputable then id take it back and ask for a decent one while its still in warranty.
i do have tiny bit of light leakage near the buttons, that does seem common.
Mine is well made too, no hardware problems.
I have a silver one, solid as a rock, light leaks are present though...
I've been having a weird screen issue lately, independent of rom or kernel; my screen won't respond to touch input directly beneath the status bar.
For instance, if I touch an icon or button at the top of the screen, it does not respond at all... Unless I rotate the phone into landscape mode and select the command.
The status bar itself works fine, I just have to tilt the phone to use the area of the screen underneath it. Weird.
Just a shot in the dark, do you have a screen cover that might have lifted a bit?
ca1ne said:
Just a shot in the dark, do you have a screen cover that might have lifted a bit?
Click to expand...
Click to collapse
I have a matte, anti-glare cover, but it's tight as a drum. Not even an air bubble.
Similar thing happened to my last phone. Only it was the bottom corner. Never found a solution. Ended up getting new phone.