AT&T Rom for Orbit 2? - Touch Cruise ROM Development

I recently purchased an Orbit 2 stateside and have been using it on Cingular/ATT for a few months. I struggle with internet connections routinely. Sometimes I can tether (modem for pc), sometimes surf directly, and always sms, but sometimes mms. What I'd like to do is simply find an AT&T ROM to flash to. Then I shouldn't have to continually tweak my connection settings. Has anybody considered or done this? There are a number of ROM's out there, but I haven't seen one specific to the Orbit (Not an AT&T product). Or alternatively, is there an AT&T ROM that will work well with the Orbit 2?
Any advice is highly appreciated.
Russ

No device... No ROM...
The only way to get an AT&T ROM for any device is if AT&T offered that device. Since AT&T is never going to offer this beautiful device (Due to the craptacular iPhone) there is no AT&T ROM for this device. Your best bet is to try different radios like the 1.64.08.21 or get them all and see which one works best for you. I am in MI and the 1.58.25.14 is working great for me. I am going to try that 1.64 radio though. Hope this helps...
cansler

Here is a cab that should help.

I'll give it a try
Thanks for the link.... I've tried a few of the .cab's for setting all the media settings with varying degrees of failure. But, I'm game for trying another. Do you recommend I delete all current settings, or just over-write.
Russ

turcomora said:
Here is a cab that should help.
Click to expand...
Click to collapse
i use this cab on my Orbit 2 w/at&t and i never have any connection problems...

No dice
I immediately get the "cannot connect with current connection settings. To change.... blah, blah, blah.
Life is cruel. Any further suggestions. I'm committed to figuring this out in the next few days or ebay'ing it.
Thanks,
Russ

I am using the touch cruise on AT&T and I do not have or have had any connectivity issues at all. I have even had signal 7,000 feet up in the mountains in the middle of now where and received phone calls and access data such as emails ect...

bkeaver,
Great for you gives me hope.
I had things setup once before and didn't do a backup. Accidently hit the O2 Operator Settings and couldn't shut it down fast enough. Been hosed ever since. Still hoping for divine intervention from the guru's here and at other places.
Russ

I think I finally found the magic recipe.
http://forum.xda-developers.com/showpost.php?p=1360192&postcount=1
I 'disabled proxy' using this cab setup after using an MMS cab setup. It has the ability to enable/disable proxy. I'm guessing this is different than whether or not the connection is trying to use one.
Should know in a bit if I can actually connect to my work emails again.
Thanks all,
Russ

Suweeeet Georgia Pie!!!
Finally, I'm connected to my work calendar. I wear so many hats at work that I'm only in my office 20% of the time and I really depend on my electronic reminders. They don't work so well when I'm not in my office. Having my electronic leash is a godsend (my daughter has a different opinion of hers

rtarver said:
I immediately get the "cannot connect with current connection settings. To change.... blah, blah, blah.
Life is cruel. Any further suggestions. I'm committed to figuring this out in the next few days or ebay'ing it.
Thanks,
Russ
Click to expand...
Click to collapse
i understand you're good to go now and that's what counts! curious to know, however, if you deleted all of your previous connection settings prior to installing the cab file? i ask because i've been using the cab file to reconfigure all my connection settings over the last 4-5 months without a problem.

Related

Wizard Tmobile Wifi

Hi everyone. I just bought the new Tmob MDA yesterday and have been tooling around tryin to figure the wifi thing out.
When i bought it from the store the salesperson said that the Wifi is only active when you have the Data plan activated..... Which kind of doesnt make sense. I understand the PRS side of it but not the Wifi side....
I downloaded the CABs and registry entries and all that good stuff, with no luck.
The latest thin I tried in order to connect to a network is install WoFo companion from Socket.
HERES THE CATCH!!!! The socket apprecognizes networx in the area, but the WM2005 doesnt allow it to connect. When you say connect the WM2005 Available Networx page is blank.
Can anyone help? I really need wifi on this machine....
thank you for listening.
Yes wifi should work out of the box to - b networks. Saleperson is wrong - that only applies to gprs as you said.
What reg tweaks and cabs did you install? that should be unnecessary unless you want to logon to g networks.
Try the registry wizard that will tweak for g and show wifi plugin on the today screen. http://forum.xda-developers.com/viewtopic.php?t=39725
use latest version r.
One thing it might be worth looking at is downloading and installing the latest T-mobile rom. My wizard refused to connect to my secured wireless network, unless I removed all security and made it completely open ( like that's a good thing to do in this day and age) Installed the latest ROM update, and I could connect a lot more easily.
After you get used to your wizard, I can heartily recommend installing the K-Jam rom, it seems a lot faster.
thx
thx for you replies guys. i just flashed the rom to the latest k-jam.
i knda prefer no to have any tmobile branding anyways.
everythingn worx fine now.

Wifi is flakey at some APs

I have installed and uninstalled a number of firmware/mod combinations on my xv6800 in hopes to get the GPS working. I don't believe that's going to happen (saddly, I feel like there's a conspiracy out there to trick peeps like me into spending weeks on this problem without any positive outcome) so I'm currently focusing on what DOES work with this device.
One thing that's flakey is the wifi. At home I'm running WEP128. It connects sometimes, others it will not. When it does not automatically connect but sees it, it asks for the key each time. What's the deal with that? Entering my long a$$ key each time has made me memorize it, but it's still a serious PITA. I don't have the same issue at most other places - still using WEP128. Doesn't appear to have any issues connecting to open APs. Does have issues connecting to a friend's AP, i that it doesn't even SEE it as available any more, after the initial 3-4 connects.
Thoughts on why this could be happening? Not having the GPS makes me very angry, but then to not have reliable wifi practially makes the device pointless, as I have another phone, my own PED and an actual good camera... and a laptop.
thanks for any helpful thoughts.
Chris
Chris,
I'm assuming from your post that the "XV" indicates you have a Verizon Phone? If so you might look at this link pertaining to GPS
http://www.phonenews.com/how-to-add-gps-to-htc-mogul-xv6800-p4000-titan-2663/
I'm not sure what to tell you about the WiFi. Mine works fine...
iamchrismoran said:
I have installed and uninstalled a number of firmware/mod combinations on my xv6800 in hopes to get the GPS working. I don't believe that's going to happen (saddly, I feel like there's a conspiracy out there to trick peeps like me into spending weeks on this problem without any positive outcome) so I'm currently focusing on what DOES work with this device.
One thing that's flakey is the wifi. At home I'm running WEP128. It connects sometimes, others it will not. When it does not automatically connect but sees it, it asks for the key each time. What's the deal with that? Entering my long a$$ key each time has made me memorize it, but it's still a serious PITA. I don't have the same issue at most other places - still using WEP128. Doesn't appear to have any issues connecting to open APs. Does have issues connecting to a friend's AP, i that it doesn't even SEE it as available any more, after the initial 3-4 connects.
Thoughts on why this could be happening? Not having the GPS makes me very angry, but then to not have reliable wifi practially makes the device pointless, as I have another phone, my own PED and an actual good camera... and a laptop.
thanks for any helpful thoughts.
Chris
Click to expand...
Click to collapse
I have the verizon Titan and just use mac filtering on my wireless router. The encryption slows it down to much for me and basically need the same encryption scheme on both sides to get it to work properly. I don't do anything that it needs to be encrypted and the mac filtering keeps the neighbors out as well.
timm9 said:
Chris,
I'm assuming from your post that the "XV" indicates you have a Verizon Phone? If so you might look at this link pertaining to GPS
http://www.phonenews.com/how-to-add-gps-to-htc-mogul-xv6800-p4000-titan-2663/
I'm not sure what to tell you about the WiFi. Mine works fine...
Click to expand...
Click to collapse
Wow, of all the tuts and instructions I've tried and read, that one has never crossed my screen - and I have tried at least 4-5 different ones. The phone's already unlocked and has a custom rom on it. I didn't get an impression either way if this method will reset the device/settings/files/etc in it again. I guess I could try it out. Thanks.
I'm getting to the point of just wanting to pay someone to get teh GPS working on it.
The Wifi issue is just weird and flakey. No rhyme or reason I can see.
Chris
jambrose said:
I have the verizon Titan and just use mac filtering on my wireless router. The encryption slows it down to much for me and basically need the same encryption scheme on both sides to get it to work properly. I don't do anything that it needs to be encrypted and the mac filtering keeps the neighbors out as well.
Click to expand...
Click to collapse
I think of doing that often... but well... I don't have a but. WEP is hackable, but feels secure enough , considering I have a bunch of secure APs in my neighborhood... some obscurity helps as well.
I know that sometimes if I restart my AP (linksys wrt54g) the xv6800 will just find it and connect on it's own.
Chris
There is absolutely no reason why gps should not work on your device. In fact in this forum we really don't even discuss it too much anymore because it's really just an understood thing to be working. If you are on verizon use the latest alltel radio 3.42.xx I can't remember exactly, load dcd's 3.2.6 or 3.3.4 and start from there. Wifi on these roms have power saving features make sure if you are using wifi that you have strength up to full. Also, all the moguls that I have had, DO NOT COUNT ON THEM AUTOMATICALLY FINDING ACCESS POINTS, simply go to start->settings->connections "view all available access points" and select the one you want to use. I have heard cases of gps having trouble locking if wifi is on so make sure the switch is off and vise versa. Do the verizon qpst and registry settings change. On verizon you should have a lock within 30 seconds everytime if you are within the continental US. Good luck and take your time.
Sweeny Russ said:
There is absolutely no reason why gps should not work on your device. In fact in this forum we really don't even discuss it too much anymore because it's really just an understood thing to be working.
Click to expand...
Click to collapse
Haha... yeah, that's what's so frustrating. So many people getting it to work and me not. I'm no dolt. I follow directions quite well.
If you are on verizon use the latest alltel radio 3.42.xx I can't remember exactly, load dcd's 3.2.6 or 3.3.4 and start from there. Wifi on these roms have power saving features make sure if you are using wifi that you have strength up to full. Also, all the moguls that I have had, DO NOT COUNT ON THEM AUTOMATICALLY FINDING ACCESS POINTS, simply go to start->settings->connections "view all available access points" and select the
Click to expand...
Click to collapse
I have 3.42.something new within the last two months. My first attempt was with the DCD. Nada.
As for finding available access points, at my friend's place, it just shows it listed as unavailable. At home, it will SEE it and even attempt to connect, but often fails, except for those random times when it will connect.
one you want to use. I have heard cases of gps having trouble locking if wifi is on so make sure the switch is off and vise versa. Do the verizon qpst and registry settings change. On verizon you should have a lock within 30 seconds everytime if you are within the continental US. Good luck and take your time.
Click to expand...
Click to collapse
Hm... will it maintain the lock with the wifi turned back on afterward? The whole point is to be able to use gmaps with the GPS. I can install other s/w that has it's own maps as well, bypassing the need for the wifi, but for starters, getting GPS working first is important.
It's a verizon phone, but I don't have service turned on yet. I'm not going to switch my number over until I'm happy with how it's set up. I do not intend on using a data plan - too expensive, so wifi when in range and other gps s/w when I'm not will be used.
Thanks for the words of encouragement. I have taken some serious time with this. The nice thing is that I don't have to rush, so I've tried MANY different things from the forums and even the PPCgeeks IRC channel. If I practice any more patience, I'll be sleeping.
Chris
iamchrismoran said:
Wow, of all the tuts and instructions I've tried and read, that one has never crossed my screen - and I have tried at least 4-5 different ones. The phone's already unlocked and has a custom rom on it. I didn't get an impression either way if this method will reset the device/settings/files/etc in it again. I guess I could try it out. Thanks.
I'm getting to the point of just wanting to pay someone to get teh GPS working on it.
The Wifi issue is just weird and flakey. No rhyme or reason I can see.
Chris
Click to expand...
Click to collapse
That phonenews article was VERY helpful in getting me started, but:
It is ancient. Those old roms have problem. Use the newest DCD roms and radios found here. (thanks DCD and everyone)
ALSO, on the GPS.
If you EVER, EVER, installed the new Verizon MR1 upgrade, the GPS is locked. No worky no more..... But, simply find the older Verizon rom, it can be found. Downgrade to it and run it. Then go straight to the DCD rom/radio.
worwig said:
That phonenews article was VERY helpful in getting me started, but:
It is ancient. Those old roms have problem. Use the newest DCD roms and radios found here. (thanks DCD and everyone)
ALSO, on the GPS.
If you EVER, EVER, installed the new Verizon MR1 upgrade, the GPS is locked. No worky no more..... But, simply find the older Verizon rom, it can be found. Downgrade to it and run it. Then go straight to the DCD rom/radio.
Click to expand...
Click to collapse
I did try the MR1 upgrade based aGPS hack, but I then realized that aGPS only matters if you've got a working GPS at all. Anyway, I then downgraded again and started over from scratch. I got my phone in September and did my series of hacks/upgrades/unlocks over the course of two weeks or nightly tries and retries. It's nice to hear someone say it WILL work, but Murphy's Law is working overtime with me on this one.
It is my understanding that if you don't have internet access than gps will not just not work on mogul. The gps one chip I believe is strictly an AGPS chip and cannot lock without using agps. However I guess some people have done it and use it, although even if you get it to work the lock will take forever. The mogul really needs that emphemeris data from the north american gps servers to function correctly. I didn't realize these were your terms.
Sweeny Russ said:
It is my understanding that if you don't have internet access than gps will not just not work on mogul. The gps one chip I believe is strictly an AGPS chip and cannot lock without using agps. However I guess some people have done it and use it, although even if you get it to work the lock will take forever. The mogul really needs that emphemeris data from the north american gps servers to function correctly. I didn't realize these were your terms.
Click to expand...
Click to collapse
I've never seen it written anywhere that one would be required to have a data connection with the service provider to get a GPS lock. Seems ridiculous to me. If I wanted to pay for a data connection, then why the heck not just pay for the VZ Navigator access??
I've never seen aGPS as a requirement either. If all the tuts were about aGPS, I'd see that having that data connection was important. Boy, I sure could use a definitive on this. If I KNOW for fact that GPS just doesn't work without a data connection, I'd have to suck it up and get an external bluetooth GPS device if I care enough. I have believed however all along that the whole point was to access GPS hardware without incurring data charges.
thanks,
Chris
http://www.gpspassion.com/forumsen/topic.asp?TOPIC_ID=47602
its not the mogul, but same idea.
iamchrismoran said:
I did try the MR1 upgrade based aGPS hack, but I then realized that aGPS only matters if you've got a working GPS at all. Anyway, I then downgraded again and started over from scratch. I got my phone in September and did my series of hacks/upgrades/unlocks over the course of two weeks or nightly tries and retries. It's nice to hear someone say it WILL work, but Murphy's Law is working overtime with me on this one.
Click to expand...
Click to collapse
Also, not trying to undermind you, but why did you aquire the mogul if you weren't planning on using internet access? I mean you loose live search, google maps, pic and video messaging, skyfire, ie, youtube, and pretty much everything that makes a mogul a mogul. If you bought it for the soul purpose of using as a gps device you definitely bought the wrong device.
Sweeny Russ said:
Also, not trying to undermind you, but why did you aquire the mogul if you weren't planning on using internet access? I mean you loose live search, google maps, pic and video messaging, skyfire, ie, youtube, and pretty much everything that makes a mogul a mogul. If you bought it for the soul purpose of using as a gps device you definitely bought the wrong device.
Click to expand...
Click to collapse
TOTALLY reasonable question.
I will use the phone when I have it set how I like it.
I got it so I could have a reasonably convenient way to freely check my email and surf when in wifi range without needing to lug my laptop around with me. I got a good price on it, much cheaper than an actual laptop.
Nice sized screen for when I want to actually watch a ripped movie or TV show and the option to install other software on a whim to have with me is just great. I got a ppc that can be a phone essentially. I'm not a phone person, too cheap to pay for a text plan, but wifi is key. The ability to open this phone up for GPS use was a major factor in picking it from lots of research before diving in.

HSDPA, will donate for help!!

Hi guys, i know this is a common problem amongst some of us, there are several threads discussing the connection drops but please there must be someone out there who knows something about it.
Basically with HSDPA enabled, the connection will last a random period of time before disconnecting by itself and displaying: cannot connect for an unknown reason.
When HSDPA is turned off, only 3G is used, although this works fine, it is fairly slower.
I am on T-Mobile UK, I have phoned their technical support, we have established it is not the sim card but the phone itself and have tried a variety of steps to solve this, for example receiving band settings for WCDMA, this has not fixed the problem.
I have tried changing the username and password combinations and have tried every combination of every advanced network option. I have used the T-Mobile stock rom 1.43, official HTC ROM 1.66, duttys hg, energyROM, artemis 5.0 and artemis 5.5 (would recommend btw) using MTTY before every flash, and every single different radio combination.
Myself, and many people here would be very grateful for any help posted.
Thanks in advance
Why don't you try Settings > Connections > Advanced network > GPRS tab > change from PAP to CHAP.. and reset... or viceversa.. that helped for me..
Thanks for the post, i've tried all that i've tried all advanced settings, at most they last for a day or so but after a while the connection dropouts seem to worsen
Ok ive just gotten off the phone for the third time with the technical support
basically what they've said is that the hsdpa WILL disconnect because the mobile towers simply can't handle the traffic.
He said in his honest opinion I should disable it because it simply won't work well and there is no fix.
Taking the piss juuuuust a little bit
Mine on t-mobile uk will show H, but usually drop down to 3G. It won't give me an error when it drops down though.
It sounds like its not transferring from H to 3G.
To be honest, i was unaware t-mobile ran HSDPA till I got my HD2 (never showed on my BB).
mine switches between 3G and H too, this happens when the connection is being used (for example loading a web page) when the job is finished (page has finished loading) it turns back to 3G right?
are you saying that your connection never disconnects?
may i ask which radio and rom you are using?
thanks!
For my personal experience, I have for over a month, on versions 1.48, 1.66 by HTC, artemis versions, versions of other French chefs. had no problems,
Login Exchange push 24/24 without any cuts, I solicited the network with opera I passed automatically 3g H, and since February it to completely fall with the problems that everyone encounters (lost connection for several minutes , unable to connect to 3G without hard reset)
to remove the sim chip, I try with another chip of the same operator, another chip from another operator, the problem is still there.
For several days I have also continued a Touch HD, it faces no problems, no problems in connection 24/24.
In short, impossible to challenge any operator, any base station, any sim card.
It is then that the problem come from HD2:
-Software: We all try every combination of rom and radio rom possible.
It is the hardware, maybe the chip integrated into a concern for design, manufacturing concerns on some series, may be dysfunctional due to incompatibilitée between several chips of the phone, short, HTC should look into the problem.
cgrec92 said:
mine switches between 3G and H too, this happens when the connection is being used (for example loading a web page) when the job is finished (page has finished loading) it turns back to 3G right?
are you saying that your connection never disconnects?
may i ask which radio and rom you are using?
thanks!
Click to expand...
Click to collapse
correct, it never disconnects.
It will switch seemlessly between them, when using or not using.
same one it came with. O2 HD2.
ROM 1.43.206.4 (70315) WWE
RADIO 2.04.50.22_2
I've also been struggling with this problem ever since I got my HD2 three weeks ago. However it seems like only a few people experience this.
My case is exactly like cgrec92 described. I'm on a 3.5G network in Denmark (3 Mobile), the phone shows the 3G connection at all times. When things do work and I use Opera/weather/Twitter/email etc, the symbol changes to H and I know the data connection is functioning. I can be using this for a whole hour without any problems.
However, if I put the phone down for a while and then pick it up again to use one of its data services, very often it does not connect to 3.5G (or H) anymore. It will still show the 3G icon on the screen, but there's no data connection. Then I go to Connection Manager and I can see that data connection shows as Off - and after a few seconds it goes back to On by itself That does not mean the problem is solved, as the phone still fails to establish any data connection. What I need to do then is manually turn off data connection and re-enable it again, which makes the 3G symbol immediately change to H. Then everything starts working again - until the next time it stops working...
I contacted the HTC customer service and they said it might be a driver-related issue, recommended a hard reset. I did that and for a few hours I thought it solved the problem, but no, data connection still disconnects by itself.
I spoke to 3 Mobile's technical service and they told me to update my software, which I had already done previously (I'm running stock 1.66 ROM Danish). They also said they never received any such complains about the HD2.
Like cgrec92 I've also played with all kinds of network/band settings, but it did not make any difference.
***
One question: isn't the phone supposed to automatically connect via EDGE when it cannot connect via HSDPA? Because in my case it will only establish data connection via H, never EDGE.
Any advice is greatly appreciated!
My take on this FWIW
It's not the phone!
It's the radio ROM installed.
I live in an an area where T-mobile say I can't get HSDPA.
However, I know that I can. How? Because 3 network uses the same local cell and transmitter as T-mobile and their signal will rip your eyes out!!!!!!!!!
All information obtained from a good friend of mine who works for BT, who, service manage the cells for the networks.
Plus, in this location, the cell traffic is then handled by BTs digiatal backbone which takes it who knows where after that.
So I have a very isolated situation in which I know there is a decent HSDPA signal, but I have had trouble with drop outs on my two previous phones (Nokis 5800 and HTC Touch Diamond 2) and originally on my two T-mobile mobile broadband feeds using Huawei E220 cell network modems.
All fixed when I finally found the right Radio and flashed it on the phones and unlocked and flashed the latest modem firmware.
My broadband connections are always on and never drop out and my HSDPA signal on my HD2 is through the roof!
To further emphasise the point all the equipment is used (when home based) behind solar glass which is notorious for blocking mobile phone signals.
Land on the best one and you will get incresed battery life as well.
Bottom line is try the latest radios (2.08.50.08_02 in my case) and I think you may be surprised at the results.
Current result of speed test 09.31 hours
ADSLSPEED.COM | Speed Test
3 minutes later
ADSLSPEED.COM | Speed Test
I have the same problem with the connection dropping. What I did to make it work was to disable HDSPA and putting GPRS to CHAP instead of PAP, and so far I have no problems at all
Thanks for the reply and tips. I also did the same earlier today, except that I did not change PAP to CHAP :O. I was waiting until tomorrow before I posted any results, but I gotta say so far the connection has been stable just like yours.
I also called HTC's customer service in Denmark and the fellow I spoke to was very helpful but he said he has never heard about such problems. He sent me updated network settings via sms, but it did not fix the problem.
I mean, only some users around the world suffer from this problem, right? So what is it that's wrong with our devices? Is it a production fault? If I exchange my phone for a brand new one maybe I won't be unlucky again? When 3 DK finally told you the problem was unfixable, did they mention other users with the same issue? Did they ever offer to replace your phone?
DORMIU said:
Thanks for the reply and tips. I also did the same earlier today, except that I did not change PAP to CHAP :O. I was waiting until tomorrow before I posted any results, but I gotta say so far the connection has been stable just like yours.
I also called HTC's customer service in Denmark and the fellow I spoke to was very helpful but he said he has never heard about such problems. He sent me updated network settings via sms, but it did not fix the problem.
I mean, only some users around the world suffer from this problem, right? So what is it that's wrong with our devices? Is it a production fault? If I exchange my phone for a brand new one maybe I won't be unlucky again? When 3 DK finally told you the problem was unfixable, did they mention other users with the same issue? Did they ever offer to replace your phone?
Click to expand...
Click to collapse
Erm!
It's your radio!
But, I think I did say that in a previous post.
You had a helpful fellow who sent you updated settings?
And he thought that was going to fix your problem?
That was helpful!
It's your radio!
The technicalities are beyond a customer assistant at the end of a phone. They work from a script.
I'll send you the settings.
Have you done this?
Have you done that ?
Never heard of anyone else with your problem!
It's your radio!
T-mobile uses PAP protocol (at least they do here in the UK) and it's a handshake protocol so changing that won't really do anything to the signal definition.
You have it or you don't.
It's your radio!
There is no "production fault".
You are not "lucky" or "unlucky".
You are in an area where you will suffer from this because of the ???????
THE RADIO!
I think I have made my point.
If it turns out that you don't have a radio issue then please feel free to admonish me.
Until then----------
It's your radio!
well I don't mean to sound rude but do you SERIOUSLY think we haven't tried that? ive tried every possible radio available here and every different rom, so excuse us for trying new things.im glad your not having any troubles yourself because it is really annoying
perhaps you could post us your rom and radio?
I don't suppose you could post us your settings in advanced network?
did you use the connection setup?
thanks for your help
Yes, I was about to mention something similar. I haven't tried combining different ROMS & Radios myself, but I know people like cgrec92 who have with no good results.
And if it is the radio, then every 3 Denmark user like me would be experiencing the same problem, correct? I don't think that's the case. Actually when you read the forums you will find users from different countries with this problem, and they/we are not the only ones with a certain combination of ROM/Radio.
So yes, by disabling HDSPA I finally managed to have a stable data connection (but no 3.5G, obviously). At this point no one seems to know the cause of this issue, but I suppose it's naive to expect a future ROM to solve it, after all it's not a widespread problem. Is HTC even working on it? Are we sure it's not our devices that are faulty?
I honestly have no idea, but I cannot just accept this problem and live with it after all the money I put into this phone. That's why I brought up the possibility of having it exchanged for a brand new one in hopes that it will not have this problem.
Any ideas?
cgrec92 said:
well I don't mean to sound rude but do you SERIOUSLY think we haven't tried that? ive tried every possible radio available here and every different rom, so excuse us for trying new things.im glad your not having any troubles yourself because it is really annoying
perhaps you could post us your rom and radio?
I don't suppose you could post us your settings in advanced network?
did you use the connection setup?
thanks for your help
Click to expand...
Click to collapse
The post by pa49 was to DORMIU.
I'll pm you my t-mobile settings.
And I cant use the connection setup, being an O2 HD2, it only allows selection of O2.
cgrec92 said:
well I don't mean to sound rude but do you SERIOUSLY think we haven't tried that? ive tried every possible radio available here and every different rom, so excuse us for trying new things.im glad your not having any troubles yourself because it is really annoying
perhaps you could post us your rom and radio?
I don't suppose you could post us your settings in advanced network?
did you use the connection setup?
thanks for your help
Click to expand...
Click to collapse
I referred to my radio in my previous post -20.08.50.08_02.
My OS ROM is Leo Lite 3.
Connection setup used and no further settings.
My explanation for this is the fringe nature of the received signal.
The radio its constantly 'hunting' for a signal and the radio software has difficulty in locking on.
BTW OS ROM and settings ready don't affect the efficiency of the radio signal.
MidnightDraven said:
The post by pa49 was to DORMIU.
I'll pm you my t-mobile settings.
And I cant use the connection setup, being an O2 HD2, it only allows selection of O2.
Click to expand...
Click to collapse
I appreciate the help, but he doesn't seem to understand the issue here. It's not that we have low connection, or that we cannot connect to the 3.5G network. The problem is that the phone's data connection will automatically disconnect even when we are in an area with full 3.5G signal. The phone will connect for a while and then, moments later, in the same spot and with full signal, data connection is terminated. So I just can't see how the radio has anything to do with that, especially when there are hundreds of other users out there with the same ROM & Radio as us and in the same network. And yet they do not experience this problem.
Ive have similar issues but it depends where i am it appears that some towers its ok where others its not!
mo
DORMIU said:
I appreciate the help, but he doesn't seem to understand the issue here. It's not that we have low connection, or that we cannot connect to the 3.5G network. The problem is that the phone's data connection will automatically disconnect even when we are in an area with full 3.5G signal. The phone will connect for a while and then, moments later, in the same spot and with full signal, data connection is terminated. So I just can't see how the radio has anything to do with that, especially when there are hundreds of other users out there with the
same ROM & Radio as us and in the same
network. And yet they do not experience this problem.
Click to expand...
Click to collapse
The radio differentiates between all the different levels and types of signal and it depends on how exact it interprets the signal. They are supposedly optimized before release and then re optimized with each newly released version. Network operators then have their own network parameters and again the radio has to accommodate this as well. One radio will never satisfy all these criteria and some of you will be in the wrong place at the wrong time on the wrong network with the least effective radio.
I can assure you that I most certainly do understand the problem and that is why, in my own case, I have resolved it.

HD2 Web Connectivity Issues and Analysis

Seriously people....
I've seen lots of threads recently. People are complaining that the HD2's data connection cuts out, leaving them unable to access the Internet from their phones for who knows how long. I know, it IS kinda annoying...But the thing is..
I can tell you this IS NOT a hardware problem. It's something to do with either the OS....or something in the phone's registry settings which no one has picked up yet...I hear that phones like the TP2 do not have this error, and I agree. My old unbranded Touch Pro 2 was brilliant, I could use it for IM and texts anywhere...LOL I used to sit on the Bus while people stared at my phone, while I was on Messenger talking to my phone. Anyways, here's what I wanna tell you guys. Hope I help out everyone in some way or another.
What I have:
HD2
3 Mobile Sim-So yeah, My Operator is 3 UK
Living in London, UK
Using ENERGY's 17th March Version ROM
HUSPA, HDSPA Enabled
What I've noticed:
The phone cuts out the signal when the transition between 3G and H occurs in the icons. As a result, the Internet cuts out temporarily, and programs such as Messenger lose connectivity for a while. For example, when the icon is on H, and no one's talking on Messenger, the Icon changes back to 3G....during this moment it cuts out sometimes..until it reverts back to the H icon (Got that? I know, it's a little long and complicated when I word it like that, but read it out and it'll make sense xD)
Now, whenever I have the phone connected to my PC/Laptop (Either as a Wi Fi Router or through the cable and then using Internet Sharing, either way, the phone does NOT change back to 3G, it stays constantly on H (Mind you, I usually download during this period). Anyways, the point being that the connection is VERY stable and constant, when in this state, connected to my PC/Laptop and the device is accessing the Internet through my phone's Data Connection. So what do you all think? And what have YOU found out? Leave your responses and ideas below
Some things I have found out are, if you Enable ONLY HUSPA in the Settings/Connectivity options, the connections seem to be more stable. Furthermore, if you really want to, Disable Advanced Connections, stay only on 3G, and enjoy a LOT of stability (At the cost of slower speed surfing and downloading )
My HD2 does not connect at all anymore. I called in to support because I completely lost data connectivity (web browser, email, slacker, whatever - no connection). They verified no troubles on their end. I moved the sim to my old touch pro (running Energy ROM w/ winmo 6.5 and Sense 2.1) and that phone connects fine. So it's not the SIM, and it's not the network.
I've also done a hard reset to get back to stock and still have the problem, which tells me that it's not a registry / software setting.
They only thing that leaves is faulty hardware - or firmware that a ROM hard reset wouldn't affect. Either way I need to replace the device altogether.
Unfortunately, tmo is out of stock and so I can only wait for a more to become available before it can be replaced.
csharper said:
My HD2 does not connect at all anymore. I called in to support because I completely lost data connectivity (web browser, email, slacker, whatever - no connection). They verified no troubles on their end. I moved the sim to my old touch pro (running Energy ROM w/ winmo 6.5 and Sense 2.1) and that phone connects fine. So it's not the SIM, and it's not the network.
I've also done a hard reset to get back to stock and still have the problem, which tells me that it's not a registry / software setting.
They only thing that leaves is faulty hardware - or firmware that a ROM hard reset wouldn't affect. Either way I need to replace the device altogether.
Unfortunately, tmo is out of stock and so I can only wait for a more to become available before it can be replaced.
Click to expand...
Click to collapse
Which phone company are you with? I experienced the same problem with 3UK in North London for a couple of months up until the beginning of last week but it was a problem at 3's end, not mine. Other people have been experiencing similar issues with non-3 phones in London (http://www.3g.co.uk/3GForum/showthread.php?t=102192).
yes, I had problems in London too before Good Friday. Especially on Tues+Wed.
Others around me inthe library also had similar issues with their iphones. I kept on switching the baseband and modes, and reapplying my 3G settings to keep it alive and solve the outages.
Most people with issues were on vodafone or O2 (like me).
It would work, then cut, then work.
I thought at first it was because I had a custom ROM, but iphone users had the same - and lots of timeouts on requests.
I DO believe however that running ROMS like energy's and Dutty's HG 1.7 with 2.10 (which I'm currently running) bases as 2_08 radios is not great for the uk and exacerbates the connection issue. 2_07 is better...and in any event we SHOULD be using 1.72 based roms with 2_09 radio.
I have also noticed that on COM5 23544 builds the opera mobile 9.7 and 10 google boxes do not work. They come up as failed connection, but then i click on teh link and it works...weird huh???
So I think last week was because of network faults in London. But in general, these 2.10 based ROMS and their radios are not ideal for stability.
I had perfect call and HSDPA stability with 1.48stock+2_09 radio.
Having turned to a 23544 rom (Dutty's HG) with 2_08 radio I've had much less call and internet stability (and quality) over the stock with 2_09.
jakem said:
Which phone company are you with?
Click to expand...
Click to collapse
T-Mobile US.

Hd2 Telstra ROM 1.72.841.0 (82124)

Hi All
I need some help with my HD2.
Today I upgraded from stock rom to latest as version as on HTC website
I can't recall old version, anyway I am having an issue with this radio version which is 2.07.51.22_2
My exchange activesync keeps disconnecting, so my emails are arriving 3-4 minutes later.
I guess my question is?
Can i go back to older radio version without flashing, or worse case scenario could i downgrade to older rom?
I need some help guys.
Thanks
I am downloading now... Will try when down.
I cannot help you there, but have you tried sending a SMS? did you get a stupid notification of message being sent? I am trying to figure out a way to deactive.... No luck yet, waiting for HTC response
As for the Data sync I have had no issue as yet. I have found it a tad more reliable than 1.49. But I have only done a whole 2 hrs of testing
tmorgan4 said:
As for the Data sync I have had no issue as yet. I have found it a tad more reliable than 1.49. But I have only done a whole 2 hrs of testing
Click to expand...
Click to collapse
What a pain, so yours work ok, do you use activesync with an exchange server?
That's where my problem is.
It disconnects every few minutes, which obviouslyconsumes more battery power.
As for the sms sent notification I dont mid it.
I may downgrade to original rom, is it safe?
Thanks
host12 said:
What a pain, so yours work ok, do you use activesync with an exchange server?
Click to expand...
Click to collapse
Sorry I should have clarified. I link mine with my Exchange 2010 Server. I am getting emails as wanted.
That said I still can't sync SMS. Which is soemthing HTC is looking at and I haven't heard back in a while. I should email them to chase them up.
Hmm, I may try a hard reset tomorrow then.
Thanks
host12 said:
Hi All
I need some help with my HD2.
Today I upgraded from stock rom to latest as version as on HTC website
I can't recall old version, anyway I am having an issue with this radio version which is 2.07.51.22_2
My exchange activesync keeps disconnecting, so my emails are arriving 3-4 minutes later.
I guess my question is?
Can i go back to older radio version without flashing, or worse case scenario could i downgrade to older rom?
I need some help guys.
Thanks
Click to expand...
Click to collapse
Hi there, having exactly the same issue, did you find a solution to this other than changing out the ROM? Greatly appreciate your posts.
Telstra ROMS on HD2 are stuffed!
I've heard from a mate who works in Telstra ROM development that the HD2 images are not fully tested.. and therefore go to market with communications flaws.. eg every time you try and sync your mail or use as a shared internet device it struggles as the radio version is substandard to the rest of the Image.
Do yourselves a favour.. HSPL it... Find one of the wonderful roms that the guys/gals on here do.. and you will love using the hardware you have purchased. The HD2 is so powerful and should not be ruined by Telstra's lame attempt at a ROM.
Seems they have put way more effort into the Android ( desire ) but its still no HD2.
englundm said:
Hi there, having exactly the same issue, did you find a solution to this other than changing out the ROM? Greatly appreciate your posts.
Click to expand...
Click to collapse
Yep fixed it, apologies forgot to post solution for my issue.
After trying reflashing with new ROM, downgrading to old ROM and still having same issue, that's right after downgrading...
It clicked, see I bought device and started using activesync after about 2 months.
Before that, I had an issue with my 3G internet connection not working at all.
Weather updates, internet access, hotmail emails etc.
To fix that other issue I had to create a new internet connection.
By the time I got to use activesync I had a new internet connection, I was not using stock telstra connection.
Therefore to fix on new ROM version I created a new connection, and magically started working up to now with no issues.
And it is true telstra are bloody hopeless at testing pre-releasing ROMs.
If you need more information let me know.
Thanks
Would greatly appreciate any help in two areas:
- firstly my HD2 internet stuff is nor working at present. Clicking many of the BigPond links just brings up IE with wap.telstra.com/wap?..... and ends up just sitting there until timeout. Can you post details for setting up new internet connection that fixed this.
- which ROM did you go to. Hw did you load this. I cannot get my HD2 to connetc to Win7 x64 WMDC. Can't even see any mention of the device in the device mgr, though it did say it saw it at ones stage. Reading numerous posts - seems to be a lot of people having issues in this space..
hylandgj said:
Would greatly appreciate any help in two areas:
- firstly my HD2 internet stuff is nor working at present. Clicking many of the BigPond links just brings up IE with wap.telstra.com/wap?..... and ends up just sitting there until timeout. Can you post details for setting up new internet connection that fixed this.
- which ROM did you go to. Hw did you load this. I cannot get my HD2 to connetc to Win7 x64 WMDC. Can't even see any mention of the device in the device mgr, though it did say it saw it at ones stage. Reading numerous posts - seems to be a lot of people having issues in this space..
Click to expand...
Click to collapse
Ok.. have to say, the wap.telstra addresses are all old and many are discontinued. All those apps are simply web shortcuts that should point to a m.bigpond address.
Firstly.. you need to do a few things..
1) You will need to HSPL your phone- ( like flashing a bios ) I just used the hspl.zip.. Instructions are easy and straight forward, make sure you follow them perfectly.
2) Flash your radio to something better i did the 2.10 ( Again.. instructions need to be followed.)
3) I then had a look and found a rom on the forum ( energy GTX ) which seems to have all i want and is fast.. after you flash it.. reboot it.. and it will autoconfigure to the Telstra network.. and BINGO.. FAST Phone!!
host12 said:
Yep fixed it, apologies forgot to post solution for my issue.
After trying reflashing with new ROM, downgrading to old ROM and still having same issue, that's right after downgrading...
It clicked, see I bought device and started using activesync after about 2 months.
Before that, I had an issue with my 3G internet connection not working at all.
Weather updates, internet access, hotmail emails etc.
To fix that other issue I had to create a new internet connection.
By the time I got to use activesync I had a new internet connection, I was not using stock telstra connection.
Therefore to fix on new ROM version I created a new connection, and magically started working up to now with no issues.
And it is true telstra are bloody hopeless at testing pre-releasing ROMs.
If you need more information let me know.
Thanks
Click to expand...
Click to collapse
Hey there, thanks for this. With the new 1.72 ROM the Telstra inbuild connection set ups seem to work, can browse internet and activesync will connect when I prompt it OK (with 1.49 I had to setup a new connection with Phone line (GPRS) and telstra.wap manually (via the Telstra tech's)). I have two HD2's one running 1.49 (with this manual config) and the other 1.72 with inbuilt Telstra config's - the delay problem u described with email arriving 3 or 4mins later is still happening on 1.72 despite it appearing to connect fine, almost like the message from the exchange server is being ignored. Watching Activesync on the 1.72 when I know there is new email and there is this odd sequence, seems to check and recheck emails 2 or 3 times when just one new email has arrived but doesn't seem to pick up the trigger from the Exchange Server that new email has arrived? Does this delay still happen for you, what connection configuration did you select? Thanks v.much.
I want to know what are the real benefits or improvements on upgrading the ROM on Telstra branded HD2? Because I bought an new, unlocked HD2 from a clearance shop in Melbourne and had been into it for just 2 days. Bening a long time WM user, I got used to it and it really seems to work without any problems at the moment, so does the new ROM brings some dramatic improvements, new and fanastic functions or what? I am not after cosmetic things at all, need to know real benefits comared to old ROM.
rxsoob said:
I've heard from a mate who works in Telstra ROM development that the HD2 images are not fully tested.. and therefore go to market with communications flaws.. eg every time you try and sync your mail or use as a shared internet device it struggles as the radio version is substandard to the rest of the Image.
Do yourselves a favour.. HSPL it... Find one of the wonderful roms that the guys/gals on here do.. and you will love using the hardware you have purchased. The HD2 is so powerful and should not be ruined by Telstra's lame attempt at a ROM.
Seems they have put way more effort into the Android ( desire ) but its still no HD2.
Click to expand...
Click to collapse
Thanks, almost sold on this path at this point given the headaches, was reluctant to head down this HSPL path, is there a good reference for setting up a custom ROM specifically for Telstra's network?
Activesync usually never works with the standard Telstra connection in the HD2 Telstra ROM.
As far as im aware, it is set up to go through a Telstra proxy server, which doesn't allow the Activesync traffic.
You must set up your own stock standard connection to telstra.internet APN. Which bypasses the proxy that they have on their preloaded connection. You will however not be able to use the Telstra internet shortcuts to My Account, BigPond etc, as they require authentication with their proxy server.
So as far as I have found, with the stock Telstra HD2 ROM its a case of either one or the other: your activesync working, or your Telstra links working.
englundm said:
Thanks, almost sold on this path at this point given the headaches, was reluctant to head down this HSPL path, is there a good reference for setting up a custom ROM specifically for Telstra's network?
Click to expand...
Click to collapse
I'd like a response to this too as I'm looking at HD2 Android and need a radio upgrade from for it to run, but don't want to lose Telstra Rural coverage. The HD2 is a great device, but few Winmo6.5 app developments compared to Android or iphone.

Categories

Resources