need krome spy housing / cover - JAM, MDA Compact, S100 General

hello,
my krome spy (magician refresh) looks terrible. need a complete new housing / cover.
does anybody know, where i get one ?
at ebay i only find the plastic ones - for the "normal" magician.
does someone know - if they would fit also ? i can't imagine - since even the buttons are a litte different.
please help.

Related

New faceplate for Wizard 100 series

Does anybody know where you can get a new faceplate for the Wizard 100 series? (Cingular / Dopod styling).
Also, how does the old one come off, with just loosening the two small torq screws on the back of the slider?
Thanks!
Kanjibankers said:
Does anybody know where you can get a new faceplate for the Wizard 100 series? (Cingular / Dopod styling).
Also, how does the old one come off, with just loosening the two small torq screws on the back of the slider?
Thanks!
Click to expand...
Click to collapse
No idea where you'll get one from, but there's more holding them together than just those 2 screws.....
check the wiki for magician diss-assembling methods - they're likely to be similar, but in brief you'll need to prise the aeriel cover off, remoce 2 screws there and void warranty seal, remove the 2 screws you can see, then lever the casing away from the chassis.
Richard
Kanjibankers said:
Does anybody know where you can get a new faceplate for the Wizard 100 series? (Cingular / Dopod styling).
Also, how does the old one come off, with just loosening the two small torq screws on the back of the slider?
Thanks!
Click to expand...
Click to collapse
I recall reading a thread either here or on howardforums about someone who found a source for the stylus. When I went to the site the poster provided, I found that they provide just about every part for HTC phones. I think there may have been a minimum quantity that must be ordered, but haven't verified. Do a search on "stylus" or "found stylus" or similar here and at HoFo and see if you can find the thread.
Thanks Summiter! Do you remember how old the post was? I have been searching with no success

New case (frame) for my prophet?

My Prophet has been proved to be quite durable. It has fallen down quite a few times and still operates normally. Yet, these misfortunes have produces slight deformations to its scratch resistant metallic surface (in some parts the black color has goen away and the metallic color below is revealed)..
Therefore I was wondering:
a. Whether I can find another frame/case? (I Don't care for the provider)
b. Can change it on my own (no sending to the service-man required)
c. Whether I can use other colors (e.g. blue, or piano black etc) - dopod comes in 5 colors - XDA has been resealed in piano white..
If anyone has any info on these I would really appreciate it..
Best Regards,
Evans
Where you can get a case I don't know. But I do know you can change it yourself. Full instructions here: http://www.modaco.com/index.php?s=4b70b949c889cbd066db2acd526fda51&showtopic=240109
Black Qtek S200 @ cnn.cn/shop for $59.00. It says it's a Dopod 818 Pro housing but the picture shows a Qtek housing. Either way here's the link:
http://cnn.cn/shop/dopod-e818-housing-p-704.html
Hi there,
Cases for Qtek 9100, where can i find?
Thanks.
pimpas said:
Hi there,
Cases for Qtek 9100, where can i find?
Thanks.
Click to expand...
Click to collapse
You might have better luck asking in the Wizard Forum.
I believe that same site offers cases for the Wizard as well...look around and you should find it.

Trying to find a Housing for my hermes

Hello people... I'm a unlucky guy who bought a alignment trouble hermes... 200...
So... I've fixed the alignment problem, first, putting a little piece of card (the sim card rest), after oppening it, and putting some doubled-face ribbon, as shown in other thread here.
After it, I had to buy one new screen, because I've [email protected]$%$%$#@#ed the botton connection on the screen, whit the fu#$%#%@%#ing piece of card. . Its life. Some wins, some losts...
I'll try to fix the blank screen now, and I believe I'll have some success, but... Until now, I've done a lot of things, and my housing is completely broked.
Do you guys know what king of housing can I put in this hermes? I've found a lot of housings, but they seams to be diferents. My Hermes is like the one in the first page of this forum (this one). It could be a little idiot, but I'd like to find it black too.
They seams to be diferent of this one.
Can I use any? The d-pad seams to be diferent.
Thanks,
hey i dont know if you still need this info, but the differances ie. D-pad buttons ect all should be cosmetic should not matter at all you can make any Hermes housing work the only exception would be a housing/phone that is a at&t 8525 cingular/at&t left the vga cammera off so that housing would not have the hole for the camera on the front and that phone would not need the hole from another housing

Hermes slide indicator not working

Hi there,
Maybe someone can explain me, where is the hermes's slide indicator (or.. I don't the correct term, sorry for my bad English). My friend gave me his phone, after he was trying to change phone's cover to original htc tytn cover (of course, top part of the case did not fit on that hermes, but bottom case fit's ok). And after he assembled all parts - phone did not recognize when you are sliding the keyboard, and the screen is not turning to landscape position.
And now I want to fix it for myself, ant had tried to search where is that indicator, which 'sees' when you slide the phone. And when I disassembled - I just cant identify that thing. Only one place in my inexperienced eye is suspicious - http://img65.imageshack.us/img65/8708/dscf7321.jpg this place, in other side of LCD, where the hinges(?) is placed. But I can't understand, how its working (I have other HTC TYTN, but it's under warranty, so I cant dissasembly it to try use other parts, o smth..).
So, I would be grateful if someone could lead me to the right road' to fix this problem... if it's possible.
Thanks,
Laimis.
Yes your friend forgot to move the screen orientation magnet from the old case to the new one!! New cases do not have the magnet attached you have to move it from the old case.
See here:
Yes and you forgot to move the screen orientation magnet from the old case to the new one!!
See here:
http://forum.xda-developers.com/show...01&postcount=6
.... so let's hope he didn't throw away the old case!!
Dismantling Guides for Hermes / TyTn here www.mikechannon.net
Mike
Thank you, Mike!
you were right there is no magnet on the new case, so now I will wait until my friend will send me an old case.
God luck!
... good luck to you

[Q] HP iPAQ 910 Battery Cover

Hello,
My phone's battery cover was broken and i can't replace it. This is the only option (www ipaqrepair co.uk/ipaqpart1759.html), but it is too expensive for me.
Does anybody have another idea?
Thanks!
Emil from Hungary. (Sorry for my poor English.)
You could get one of these:
www repairhppda com/high-capacity-battery-3600mah-ipaq-910912914910c912c914c-p-1210.html
It includes a back cover designed to fit the new battery. Mind you, it's way bulkier than the original.

Categories

Resources