Can't hear phone when away from car-mounted Bluetooth unless.... - Mogul, XV6800 General

..... unless I manually turn off Bluetooth on the Mogul, or turn off my visor-mounted Supertooth BlueAnt 3. If I walk away, even 100 ft., and a call comes in, it's silent in the speaker, and no way to get it back until I re-boot. However, it re-connects to the BlueAnt when I get back in the car. So to have a working phone when I leave the car, I MUST disconnect it while they are still in range, or shut the Supertooth off before leaving the car.
Anyone else have a similar problem with any bluetooth device?

Related

Bluetooth disconnecting during call

Wondering if anyone has had this problem. I haven't pinned a time down yet. I use a motorola car kit. It will disconnect and end the call for no reason. Is there a timer to auto disconnect in the bluetooth stack? Any help is appreciated.
approx 4minutes or less
I was having a problem w/mda and bluetooth and sometimes without bluetooth, in that the entire network would just drop when the call gets close to 4 minutes.... I called tmo about it and they simply gave up and said maybe its the phone...so they sent me a replacement mda, used it today during one call and couldn't believe that the call lasted longer than an hour...
Mine is only with bluetooth. I guess a little more info is needed. If I hit the voice dial button on my car kit I get the voice command tone. I have also used bluetooth to play music over the car kit with the voice command controls(just for fun, horrible quality). It will disconnect while it's playing music no call involved. I have a feeling it's the bluetooth connection timing out but I'm not sure. It's frustrating.
so its not happening during phone calls???
see there might be a bluetooth timeout that tmo doesn't know about...I have to use bluetooth and it seems like every 4min or less it blanks out everything and sometimes I even have to re pair the two devices.... I would try making calls and using the bluetooth w/o car kit...mine did some of the samethings like streaming music thru bt headseat and it would blankout with that also even when not on a call..
Car Kit Not Staying Paired???
I guess I wasn't clear. It happens in both situations. I think i have to re-pair after as well. As far as I know it doesn't stay paired. When a call comes in I usually have to wait about 2 rings before it rings through the car kit. Also when I make a call by hitting the voice dial button on the car kit the blue light blinks for about 2 seconds then I get the voice command sound. I assume that the blinking is it re-pairing. I guess I need info on how to keep it paired.
Anyone? I have found that time dosen't seem to be a issue as it has done it a 1min 43 seconds and 2 mins 38 seconds.
GreggSymington said:
Wondering if anyone has had this problem. I haven't pinned a time down yet. I use a motorola car kit. It will disconnect and end the call for no reason. Is there a timer to auto disconnect in the bluetooth stack? Any help is appreciated.
Click to expand...
Click to collapse
Try turning on the bluetooth first while your phone is off. Once the bluetooth is on, then turn on your cell phone. I tried many times in frustration why it is saying "phone is disconnected" looking for problems. Then it works now and even the phone book in my Nokia and Garmin GPS. Hope it helps you too.
Turn on bluetooth device first while the cell phone is off. Once bluetooth is on, then turn on the latter. Hope it works. Do it everytime you use bluetooth device in your car.

Bluetooth Will Not Turn Off!!

So lately, after a hard reset and reinstalling all my apps/registry tweaks/programs, I have noticed that sometimes after getting out of my car, 05 Acura TL, the phone fails to disconnect from my car. I have been out of the car as long as 4 hours and any calls still show the headset icon in the phone application....
I need help please. It's driving me nuts.
I think that it just means that the BT radio stays on, not that it's still connected to your car. The BT radio does not automatically power off if not connected to a device. For instance, if I leave my phone where it has signal and forget to grab it on my way out to my truck for parts, the radio stays on but the link to the headset drops. I can answer the phone normally or press the BT headset to reestablish the link.
HTH
see, that is the problem. The radio is still on, and that is fine. I leave the radio on to recognize my car as soon as I start it and begin to drive. Now, however, it will not drop the actual signal from the car....it still wants to use BT so I can not hear anyone and have to hit menu while in the call and then click use handset. Very inconvenient and a new problem...never happend before.

Bluetooth Problems...please help!

Not sure if it's the phone or the car but here goes....
I have a Cingular 8525/HTC TyTn with the jetware bluetooth software to allow the battery and signal to show on the HandsFreeLink on my 2005 Acura TL.
When the car is off, and I am home, if I go out to the garage and try to make a phone call near the car, it is connected to BT and I have to wait for the call to go through, hit menu and disable handsfree in the phone.
Also, when I answer calls, the HFL beeps at me twice, the answer beep and end beep, but the call connects fine.
Thirdly, the phone and car will randomly disconnect mid call and I will have to dig my phone out from the holster as the call is transferred from the car to the handset. Afterwards, the car will not recognize the phone, and I have to shut the car off and restart it for the phone to be recognized.
Any suggestions?
Thanks,
John
bump....please? Anyone?
if your phone connects to the BT carkit even though the car is off, it sounds as wiring problems in carkit, should have an ignition sense that switches the thing off, when car is not in use....the repairing problem confirms this...try an autoelectrician or qualified installer....
well, it's factory installed in all acuras, never had a problem like this with my razr, only this phone....

8125, Buletooth and Jaguar XK

I just bought a Jaguar XK that has bluetooth. When I pair and dock the first time with the car, the phone and car see and work together just fine. But the problem comes in when I leave and then return to the car. The car sees the phone, but if I try to place a call, the car says dialing, but the phone does not call. To stop the car from dialing, I have to reboot the phone. If a call comes in, it goes straight to the phone and does not get to the car. If I delete both connections and do the whole pairing process again, it works just the first time.
Is there something in the 8125 that needs to be upgraded? I saw on this site the A2DP download and one that is VCBTFixer.exe, but I am not sure if they will they will help the problem or not.
Any advice is much appreciated!

Cannot turn on BT phone connection

Hi,
Just got G4+ unlocked for US. When pair with Bluetooth headset, the "phone" option would only work once. If I turn BT off and then back on, I can only use "media" option to pair. "Phone" option would not stay checked. Voice calls go to phone speaker. This can be fixed by soft reset or putting the phone in airplane mode and then back on. Again, only works once until BT is turned off. After the first time, all voice calls go thru phone speaker again. I have BT sets in the car and at home, but at home usually use the phone speaker, so I turn BT off once get home. Never had this issue with multiple other phones. Phone still connects automatically to the BT when I get into the car, but cannot route voice calls thru the BT.
Tried to unpair/delete device, empty cache... No luck. Only works once until BT is turned off.
Very frustrating. Phone is on stock 6.0.1 on TMo, not rooted.
Any ideas. Saw a few other posts with same issues out there but no solutions.
Thanks much.

Categories

Resources