I have the vogue (cdma) sprint version on a different carriers network. It works ok but reception has always been poor and I drop alot of calls. I do have my current carriers prl so at least its going after the right towers. My provider is going to release this phone and if I could get a hold of one for 10 minutes I could grab the qcn file off of it and use qpst rf nv manager to write it too my phone. Am I way out in left field on this one? Would this improve my reception? I believe the qcn file tells the phone when to hand off to different cell towers and how to do it.
Nick
have you tried switching to roam only if you have the new rom here is the attatched reg hack cab... install to the device and wait about a minute then soft reset then it should be an option in your
Start>Settings>Phone>Options>
roaming settings... try roaming and see if you get better service
I will give that a shot thanks.
Related
I am looking for a way to update the "Phone Settings Network" dialog on my new Advantage 7501 to include the features I have on my HP ipAQ 6945. On my iPAQ have options to do a Manual Network Selection where it will find all the available networks in range, not just the AT&T ones. Why is this important to me? Well I live in an area where the nearest Cingular/AT&T tower is over 15 miles away, however I am in what they call a "Partner" coverage area where I can connect to a Cellular One tower that is about 4 miles away. This way I can get 4 bars signal inside my home where if I can try to connect to the AT&T net using typical cell phones, I get 2 bars to none. Since both these devices are made by HTC there must be a way I can move the needed code off my iPAQ to the Advantage. The iPAQ with this manual net selection is the only phone I can use at home. I was hoping the Advantage would include a similar capability.
Can anyone point me the right direction?
daveheine said:
I am looking for a way to update the "Phone Settings Network" dialog on my new Advantage 7501 to include the features I have on my HP ipAQ 6945. On my iPAQ have options to do a Manual Network Selection where it will find all the available networks in range, not just the AT&T ones. Why is this important to me? Well I live in an area where the nearest Cingular/AT&T tower is over 15 miles away, however I am in what they call a "Partner" coverage area where I can connect to a Cellular One tower that is about 4 miles away. This way I can get 4 bars signal inside my home where if I can try to connect to the AT&T net using typical cell phones, I get 2 bars to none. Since both these devices are made by HTC there must be a way I can move the needed code off my iPAQ to the Advantage. The iPAQ with this manual net selection is the only phone I can use at home. I was hoping the Advantage would include a similar capability.
Can anyone point me the right direction?
Click to expand...
Click to collapse
Go to Start/setting/personal/phone, and go to the network tab. There you can manually select your preferred service provider.
Is this what you are looking for?
No, the display shows Current Network: AT&T and only a "Find Network" box. There is no option to look for anything else but AT&T. Maybe this is limitation arising from the AT&T SIM card I am using.
My iPAQ screen gives me a Network Selection box with "Automatic" and "Manual" options. If I select "Manual" and "Find Network" I get a list of all available cell towers within range, and then can pick one. Where I am I see "Cingular" and "Cell One DCS". I pick the Cellular One tower as it is a partner site and there are no roaming charges even thought the little roaming symbol ( a pyramid) shows up at the top.
I'll try switching SIM cards and see if that makes a difference. Well changing SIM cards made no difference except that it lists "Cingular" instead of "AT&T"
The Network Selection box with auto and manual options is there on my 7501 too. I didn't think that would be affected by your sim card.
Hey, just a thought -- did you switch to true VGA, and is the box just not showing up because of that?
I tried a Hard Reset and still do not get a network selection option. It may be due one of the CAB files that is run during the device setup that changes the US version. I'll try calling HTC Support.
Called HTC and was told that the AT&T SIM locks out the option to do a Network Selection. He tried a T-Mobile SIM in his Advantage and it came up with the Network Selection option. He "hinited" that I would have to do a CID unlock perhaps to get around AT&T's SIM restrictions, but couldn't tell me to do it would as it void the warranty.
I tried the HTC Network Wizard (Google for it) and it only allows you to set up your phone for a couple of possible providers.
We both agreed that I probably have files on my iPAQ 6945 that if I could identify them and transfer them to my Advantage I might get around this restriction.
He said he would contact AT&T and see if they have any way to get around this. What happens if you travel outside the US and try to use the phone on another network (huge roaming charges!!!) in an emergency?
I don't quite have the courage to try the CID unlocker on my brand new Advantage yet. Has anyone done this?
daveheine said:
Called HTC and was told that the AT&T SIM locks out the option to do a Network Selection. He tried a T-Mobile SIM in his Advantage and it came up with the Network Selection option. warranty.
Click to expand...
Click to collapse
ATT sims do LOCK that option. All other att phones like 8525, 8125, blackjack, etc are missing that option too.
daveheine said:
He "hinited" that I would have to do a CID unlock perhaps to get around AT&T's SIM restrictions, but couldn't tell me to do it would as it void the warrabty
Click to expand...
Click to collapse
I was under the impression that CiD unlock would fix that too but that's not true.
It's just that Some (Unofficial) Roms ignore that but most of official roms like yours dont.
daveheine said:
I tried the HTC Network Wizard (Google for it) and it only allows you to set up your phone for a couple of possible providers.
Click to expand...
Click to collapse
Network wizard will not affect that option.
daveheine said:
We both agreed that I probably have files on my iPAQ 6945 that if I could identify them and transfer them to my Advantage I might get around this restriction.
Click to expand...
Click to collapse
dont know what u mean.
daveheine said:
He said he would contact AT&T and see if they have any way to get around this. What happens if you travel outside the US and try to use the phone on another network (huge roaming charges!!!) in an emergency?
Click to expand...
Click to collapse
Att doesn't have this restriction on all the networks. This restriction is based on the country codes. Att has restriction on US, canada, and mexico.
So if you are not in those countries you will have that option available to you.
daveheine said:
I don't quite have the courage to try the CID unlocker on my brand new Advantage yet. Has anyone done this?
Click to expand...
Click to collapse
Dont because it wont help.
To be quite honest with you I dont know how you could do it on your previous phone because Att blocks that option on the network side. Even if you did change your network succesfuly on the phone, it'd still be rejected by the network.
The only thing that I can think of is that your Ipaq couldn't find a good ATT signal and connected to a patner's tower instead.
And your Advantage either gets a better gsm signal or gets a decent umts signal and connects to cingular 3g.
Try forcing the phone to operate only on the gsm network from under the band tab see if that makes a difference.
and also what is your zip code?
You can enable "Find Network" by changing the following registry key.
HKLM\Security\Phone\ManualDisable=0
That will display the network selection option and you wont void your warranty or anything like that.
It just goes away after a soft reset.
Check this thread here for more info on that.
http://forum.xda-developers.com/showthread.php?t=284201&highlight=manual+network+selection
Thanks for your response. The registry edit did indeed turn on the Network Selection. Going to Manual selection it finds "Cell One DCS" just like my iPAQ does, but when I select it I get the message "Cannot register on selected network. Choose another network, or disconnect your data connection and try again."
I have been connecting for over a year with my iPAQ to "Cell One DCS" with NO roaming charges. I guess AT&T doesn't want me to use the partner network. My ZIP is 76692 and I am located near the bridge over Lake Whitney.
There is obvious a difference in the software on the iPAQ and Advantage that is causing this to happen. I just checked the latest AT&T coverage maps and see they don't show a Partner coverage anymore.
I have installed an outside yagi antenna and signal repeater at my home so I do get a signal sometimes, but not a reliable signal.
We travel a lot so I still find AT&T coverage to be good in most places, and my iPAQ still works here now.
That's strange.
I got an ipaq 6915 from cingular and with cingular sims it pretty much does the same thing and disables network selection.
Do you have a custom rom on your 6945?
When you boot it up do you get the cingular logo?
Plus at your zip code it seems like you are far away from any cingular towers.
The only thing that I can think of is that your ipaq just doesn't find a good cingular signal, and connects to a different network.
When you do a network search on your ipaq does it actually detect Cingular as an available network? When you connect to cingular from your ipaq how many bars do you get?
I've always thought there nothing special about my 6945, but I guess there is! When I do a Network Selection on it I see both the Cingular tower AND the Cellular One tower signals. I have tried this in other locations and see several different networks (e.g., T-Mobile, and five digit numbers).
I've tried both my old Cingular SIM and a new AT&T SIM, and they both work the same in my iPaq 6945. Interesting!!! But neither will allow me to select the Cellular One tower on my new Advantage.
You are probably right about country codes for on recent cruise with stops in Grand Cayman and Cozumel the Advantage would show networks other than Cingular.
I am sorry I didn't reply earlier, but I was visiting family in Virginia this weekend. It was neat to see an "H" connection appear while sitting in DFW. Only get "E" connections out in the sticks where I live.
Dave
Oh, I should have mentioned that the 6945 is an unlocked phone from HP and is not customized for Cingular. As far as signal strength I have a cell repeater installed in my home so I get anywhere from no bars to 4 bars on that Cingular tower that is at least 15 miles away. My Cellular One is consistently 4 bars. I live in a steel framed home with a metal roof. Before I got the repeater I was using a booster amp and plugging an external antenna into my iPAQ and RAZR V3 to get a usable signal. This kept me tethered in my computer room (ugh!). When I got the 6945 and found I could manually select the Cellular One tower I then had a phone I could use throughout my home.
Several years ago I started with a simple Nokia phone before Cingular had a tower in the area, and always connected "Cingular Extend" which I now know was the near by Cellular One tower. As soon as Cingular put up their tower I have been unable to connect with the Nokia, Razr V3, and new Motorola V577.
Some of my neighbors have terminated their Cingular service because of this lack of connected to the so call "Partner" coverage.
I just flashed to DCD 2.1.0 Rom last night to activate the GPS etc. I did both options on *228. My problem is that my phone wont connect to EVDO in areas where I normally always have EVDO (aka my house). I am on the alltel network and in my home area. I am also using 3.27.00 Radio. Any help would be much appreciated!!
Here is your answer need to put ESN HEX in HDR Password Section Looking at this thread will give you instructions for this.
http://forum.xda-developers.com/showthread.php?t=366068
Does anyone have a quick shortcut to force a phone to Roaming Only instead of having to dig through the menus.
I get crappy signal at home but Alltel has a tower across the highway from our neighborhood. I don't talk on the phone much at home but the rare times I do, it would be awesome if I didn't have to run outside.
I'm looking for something where I can just mash a shortcut on my screen using one of the various launcher apps out there that will toggle the phone from roaming only to automatic and back and forth.
Thanks.
Roaming only
Sorry, but I have to laugh. Most of the roaming problems here are phones that show roaming when they are not roaming, we want to get rid of the problem that you want!!!!! Maybe we should swap phones. When I put the new ROM onto my Hermes I got the full time roaming a couple days thereafter. you can alwasy try that.
There is one thing you can do to improve your signal, but it means that you will have to sacrifice your data connection if you have one.
This means that you will do a slightly modification to your phone where instead of looking for a EVDO/Rev. A connection it is only pointing to the CDMA towers such as for calls / text.
To do this you will have to enter your phones advanced menu.
I have Verizon and dial ##778 and a menu pops up on the dialer. I am not sure what number you dial for your respective carriers, but you can try searching and asking fellow experts.
You simply just make a quick switch that can be reverted back if needed.
I've done this and get more bars then before.
http://forum.xda-developers.com/showthread.php?t=320548&highlight=roaming+app
Under roaming settings I only have "home only" and "automatic." I want a "roaming only option," but it doesn't exist, so I have to do things the hard way. My goal is to change the PRL in my phone so that its roaming all the time, much like techknowfile does in his thread here.
However, I have had trouble finding the MSL for my phone. This guide doesn't work on my Incredible; I dial ##DATA# and hit "call" but nothing happens.
How do I find the MSL for my phone?
Also, is there a better way to force my Incredible to roam on Sprint?
Edit: The MSL is 000000! That's the kind of combination some idiot would have on his luggage! Thanks madman34!
Now, on to the PRL testing!
Verizon will charge you for roaming if the triangle shows up on your phone. You can open the prl files and change the roam number to 0 and it will not roam but still use the towers.
Download and install qstp
Download sprint evdo and verizon evdo prl from colorado prl.com
Open rl editor
File
Combination prl
Join
Pick your 2 prl files
Pick output name
Put on your sd card
Dial ##755#
Hit send
000000
Prl
Update prl
Pick the one you made
Menu button
Commit modifications
Phone will reboot
Watch for the roam triangle .
Hope this helps....
Sent from my HTC Incredible using Tapatalk
intenselyinsane said:
Verizon will charge you for roaming if the triangle shows up on your phone. You can open the prl files and change the roam number to 0 and it will not roam but still use the towers.
Download and install qstp
Download sprint evdo and verizon evdo prl from colorado prl.com
Click to expand...
Click to collapse
Thanks so much! I'm going to look into the voice and data roaming charges with my Verizon plan and see what the deal is. Thanks so much for outlining the whole process; here's the website for the PRLs: http://www.corolada.com/prl/
I googled and can't find a download for verizon 2010 PRLs. Anyone have a link or can rip it from their phone??
noob_2010 said:
I googled and can't find a download for verizon 2010 PRLs. Anyone have a link or can rip it from their phone??
Click to expand...
Click to collapse
This is the Sprint Evo forum. Maybe try a Verizon forum?
I was thinking someone here already had it ripped out of a verizon phone for their use on the Evo too
HERE are a few Verizon PRL's I keep around. There is a 51926 in there, I think from June or July of this year. Also some 65 series PRL's, but I haven't used any of them. I can verify that at least in Vancouver, WA I get great voice and 3G signal with the 51 series PRL's, cant really tell the difference between them, 518, 516, 517, 519, all good for me. Roaming triangle taunts me the whole time though,
Also, link in my sig for some other PRL's for the VZW 3G hack.
JTNiggle said:
HERE are a few Verizon PRL's I keep around. There is a 51926 in there, I think from June or July of this year. Also some 65 series PRL's, but I haven't used any of them. I can verify that at least in Vancouver, WA I get great voice and 3G signal with the 51 series PRL's, cant really tell the difference between them, 518, 516, 517, 519, all good for me. Roaming triangle taunts me the whole time though,
Also, link in my sig for some other PRL's for the VZW 3G hack.
Click to expand...
Click to collapse
Thanks but i've tried 25 roams through out the month with altel/verizon and I always get 1x with 1 BAR. the only difference is some PRLs show the roam sign and others don't. This one even gave me the Roaming symbol.....What could the problem be????
I really don't know what the issue could be. I know that all the PRL's I linked will roam on 3G, so ???
JTNiggle said:
I really don't know what the issue could be. I know that all the PRL's I linked will roam on 3G, so ???
Click to expand...
Click to collapse
Well they jump back and forth from Evd and Evdo_A when I sit the phone with 1 bar. But if I try to use the phone it jumps back down to 1xrrt with 1 or 2 bars at times. I'm kind of new to the hacking scene but I think everyone thing is good on my end. Unless there are other things you suppose to do after changing your PRL?
I'm no hacker myself, so at this point I don't know what else to look at.
Whenever I run any of these PRL's, I always have my network set to Sprint only, I turn off data roaming and make sure always on mobile data is enabled. But, even at the worst, I get intermittent data loss, but never get anything other then 3g. Have you tried the 00001 and 01337 prl's from the roam hack thread?
For me, on CM6.1, if I run any of the verizon PRL's, and select Sprint Only in the wireless networks menu, I roam on VZW 3G. If I switch to Affiliated Networks setting, I will drop all signal cause it gets confused I guess. If I change back to a Sprint PRL, and Affiliated Networks, I get good voice signal, but show 1x for data. As soon as I put it back to Sprint only, my data returns to 3g.
On any new froyo sense rom, it's almost impossible to tell. A bug that seems like it may be intentional has popped up. My phone will not show 1x, but only 3g. Even when I'm on a sprint prl, and confirmed to be roaming, which would be 1x, It still shows 3g. I dug into the rom, and the icons are there, they just don't show up on a lot of sense rom's
How are you able to tell what evdo ur on? Are you on an Evo?
JTNiggle said:
I'm no hacker myself, so at this point I don't know what else to look at.
Whenever I run any of these PRL's, I always have my network set to Sprint only, I turn off data roaming and make sure always on mobile data is enabled. But, even at the worst, I get intermittent data loss, but never get anything other then 3g. Have you tried the 00001 and 01337 prl's from the roam hack thread?
For me, on CM6.1, if I run any of the verizon PRL's, and select Sprint Only in the wireless networks menu, I roam on VZW 3G. If I switch to Affiliated Networks setting, I will drop all signal cause it gets confused I guess. If I change back to a Sprint PRL, and Affiliated Networks, I get good voice signal, but show 1x for data. As soon as I put it back to Sprint only, my data returns to 3g.
On any new froyo sense rom, it's almost impossible to tell. A bug that seems like it may be intentional has popped up. My phone will not show 1x, but only 3g. Even when I'm on a sprint prl, and confirmed to be roaming, which would be 1x, It still shows 3g. I dug into the rom, and the icons are there, they just don't show up on a lot of sense rom's
How are you able to tell what evdo ur on? Are you on an Evo?
Click to expand...
Click to collapse
Theres a app called Cellumap and Phonestatus in the marketplace. It tells you the network your phone is on and cellular provider.
I'm using the sprint lovers CUSTOM rom. I guess I'll switch to cm6 custom rom like you are using and set it up like you mentioned. so I'll give this a try tommorow(sunday) and report back. but I think it's just the RURAL area I live in but then again Verizon has full coverage according to their map...
yeah, probably just ur area. You should call Verizon and tell them about the issue
You could say something like, "hey, I'm trying to use your expanded 3g service for free, but all I get is 1x. Can you give me an ETA as to when this will be fixed?" That would be fun!
I'll give those apps a try on my end and see what I get.
Well, I'm getting EVDO rev a on most of these. Provider shows digital roaming but still says Sprint. Confirmed speed tests at just under 1mbs and dialing a number without area code sends me to Verizon error message.
That is with the 51 and 41 PRL's.
Hey... This thing makes phone calls too!
JTNiggle said:
Well, I'm getting EVDO rev a on most of these. Provider shows digital roaming but still says Sprint. Confirmed speed tests at just under 1mbs and dialing a number without area code sends me to Verizon error message.
That is with the 51 and 41 PRL's.
Hey... This thing makes phone calls too!
Click to expand...
Click to collapse
Aw great for you ... well I'm installing this cyanogenmod6.1 custom rom and see what it does on a different rom I guess. If not I don't know what else I could, probably no roaming agreement with Verizon(altell had my area covered before Verizon bought them so Verizon really never had towers here....)
Ah, so that's why you were looking for the newest PRL. I would think you could get it to work with the right PRL.
Hey... This thing makes phone calls too!