Related
i used imcokemans unlocker (which i have done before) and blee0125's kitchen and really screwed up somewhere!
i cant get it past the "htc smart mobility" screen. it comes up, tells me the driver and radio versions, then those disappear like they are supposed to and...nothing else.
any suggestions would be great, plz im dying here!
i have tried hard and soft resetting and...nothing!
THANKS.
EDIT: just for those coming to this ancient and recently revived thread, this (my) problem has been solved. altho there are other people now with similar problems
Have you tried re-flashing?
jim256 said:
i used imcokemans unlocker (which i have done before) and blee0125's kitchen and really screwed up somewhere!
i cant get it past the "htc smart mobility" screen!! it comes up, tells me the driver and radio versions, then those disappear like they are supposed to and...nothing else.
can anybody help me???? PLZ im dying here!
i have tried hard and soft resetting and...nothing!
THANKS.
Click to expand...
Click to collapse
Do a camera power reset and try again.
i tried that and it didnt do anything at all. isnt that just where you hold the end key and the side camera key and stick the stylus into the hole?
if so, it have any different effect than the standard soft reset
AraqirG said:
Have you tried re-flashing?
Click to expand...
Click to collapse
and i did try...sort of. im not sure how to seeing as how i can never make it past the boot screen, and therefore cannot connect it to activesync.
THANKS.
jim256 said:
and i did try...sort of. im not sure how to seeing as how i can never make it past the boot screen, and therefore cannot connect it to activesync.
THANKS.
Click to expand...
Click to collapse
Hold down the power button and the camera button at the same time until the tri colored bootloader comes up. If that works, try flashing the stock rom for your carrier.
If that doesn't work try the same steps with the memory card removed.
If that doesn't work try to do a hard reset and see if that will take you to the bootloader.
Also, what are the numbers in on the bootloader...are you sure your device is unlocked? I believe it should say... SPL-00.40.coke... on the 2nd line if your unlocked.
You shouldn't need to connect to activesync to reboot. After you run ImCokeMan's unlocker you should be unlocked until you run it again.
As I said in the last post, all you have to do to get to the boot loader is hold down the power and camera buttons at the same time. This will put the phone into the boot loader and you should be able to flash back to the stock rom and start over.
It kind of sounds like you relocked the phone and then tried to boot a custom rom.
sorry i wasnt saying i needed to connect to activesync to reboot, i was saying i needed to connect to activesync to flash, and it wouldnt boot up so i couldnt get to activesync.
and i did to imcokemans unlocker, and everything went fine. when i was setting up the device (ie. setting password, time zone, calibration, etc...) i just decided that i didnt need to finish that as i was intending on flashing a custom rom anyway, and so any settings i put up the time to set would be erased.
having said that, i went ahead and starting flashing a custom rom right from the wm welcome screen that you get on a first boot.
thanks a LOT for your help, promptness, and attention
So are you back up and running?
well, now i am. i just took a 30 min drive down to the sprint store and got a replacement :S
thanks a lot for your help though, im scared i may really need to refer back to this thread later. but if i do, at least i know i should be able to fix it!
thanks.
well, i just did it again. i must be doing something wrong in the cooking of my ROMs...about to try out your solution..hope it works!!
wish me luck :S :S :S :S
well i was able to re-flash, but, unfortunately, it is stuck in the same "htc smart mobility" screen again. i think i have been able to narrow it down to the oemizer app. i must be doing something wrong in there.
oemizer http://forum.ppcgeeks.com/showthread.php?p=100746&referrerid=10115
ill keep cooking and trying tonight until i find what it is the problem is i guess, thx for your help guys. especially you 360discgolf.
well, after cooking and flashing too many times to remember this late, all i can do is ask for help when you guys wake up and check this thread.
in the last couple of builds i havent been doing anything with oemizer at all and it still hasnt been working, and i dont think i am doing anything extra in buildos that i havent done before in successful ROM images...it seems sort of erratic.
any suggestions/hints/comments would be great, thanks a lot.
you can't just hold the two buttons and press the reset. You have to hold the two buttons at the same time, then while holding them, use the stylus to hold the reset until it restarts. If you just tap the reset button while hold, it doesn't work.
360discgolf said:
You shouldn't need to connect to activesync to reboot. After you run ImCokeMan's unlocker you should be unlocked until you run it again.
As I said in the last post, all you have to do to get to the boot loader is hold down the power and camera buttons at the same time. This will put the phone into the boot loader and you should be able to flash back to the stock rom and start over.
It kind of sounds like you relocked the phone and then tried to boot a custom rom.
Click to expand...
Click to collapse
i'm having a similar problem. my attempt at flashing didn't go over that well and now when I turn off the device, I can't turn it on again unless I do a soft reset. I tried doing the power/camera thing but all it does is ask "are you sure, yada yada" and then the devices turns off. you were talking about a stock rom? where would I get one and how would I re-flash the rom (assuming that's the problem in the first place.).
Thanks!
vkolas said:
i'm having a similar problem. my attempt at flashing didn't go over that well and now when I turn off the device, I can't turn it on again unless I do a soft reset. I tried doing the power/camera thing but all it does is ask "are you sure, yada yada" and then the devices turns off. you were talking about a stock rom? where would I get one and how would I re-flash the rom (assuming that's the problem in the first place.).
Thanks!
Click to expand...
Click to collapse
what carrier are you?
EDIT: also:
1) what os version are you running? (build number)
2) what radio are you running?
3) what bootloader are you on? (can be accessed via holding power + camera button and poking reset hole)
4) what are the orange numbers in the very bottom right of the screen when you are booting up?
these kinds of things all need to kind of jive for the sleep function to work correctly
jim256 said:
i used imcokemans unlocker (which i have done before) ...
Click to expand...
Click to collapse
If you used the imcokemans unlocker a 2nd time, I believe you re-lock your phone.
You also mentioned that you tried to flash the ROM from the Welcome Screen. That certainly won't work. You have to be at the unlocked rainbow bootloader screen which will load when you run the RUU or when you press Power-Camera-Reset. If it doesn't go into bootloader then you've probably re-locked your phone.
denasqu said:
If you used the imcokemans unlocker a 2nd time, I believe you re-lock your phone.
You also mentioned that you tried to flash the ROM from the Welcome Screen. That certainly won't work. You have to be at the unlocked rainbow bootloader screen which will load when you run the RUU or when you press Power-Camera-Reset. If it doesn't go into bootloader then you've probably re-locked your phone.
Click to expand...
Click to collapse
haha sorry this is a problem that i had a VEERRRRY LONG time ago. have learned a lot since since then, now it is this other fella here we are trying to help him
thx tho!
i have tried to flash my 8125 with shelltool,i have followed all steps till end.
when i try to restart my mobile,nothing happen.
i just put the power to on and i have only the the rom versio which appears on the screen and last like this with nothing else,no windows start nothing even not activesyncro that mean i am even not able to reflash again.
please help
thanks.
faziahasnaine said:
i have tried to flash my 8125 with shelltool,i have followed all steps till end.
when i try to restart my mobile,nothing happen.
i just put the power to on and i have only the the rom versio which appears on the screen and last like this with nothing else,no windows start nothing even not activesyncro that mean i am even not able to reflash again.
please help
thanks.
Click to expand...
Click to collapse
Try this:http://forum.xda-developers.com/showthread.php?t=297097
Bootloader mode, and an oficial ROM
Good luck
i have
ipl 1.08.0001
spl 1.08.0001
my phone does not satrt up exept in bootloader
i cant install any rom and my screen become white with 0% and it stail 0%
i don't kno what to do so plz help
daywalker_7780 said:
i have
ipl 1.08.0001
spl 1.08.0001
my phone does not satrt up exept in bootloader
i cant install any rom and my screen become white with 0% and it stail 0%
i don't kno what to do so plz help
Click to expand...
Click to collapse
I hear funeral prices are pretty cheap for phones now a days...
apreichner said:
I hear funeral prices are pretty cheap for phones now a days...
Click to expand...
Click to collapse
I hear the Touch Pro 2 was just released today.
isn't there any one to help me???????????????
daywalker_7780 said:
isn't there any one to help me???????????????
Click to expand...
Click to collapse
It's because you tried to flash with a SPL and IPL lower than 4, I believe.
I'm quite sure you just can't flash ROM's! lol.
Hard reset your phone: Hold down the two soft-keys, and while holding them, press and release the Soft Reset button. That should bring up a black screen. Press the phone button. You should be back to your default ROM. SHOULD be.
Ivanmmj would know more about this though.
i tried to hard reset but it can't do the format,there is an error
I'm not sure but I think you may have bricked your phone. I'll say it now. You should have done your research. There may be one more thing you can do. Hold down the camera button and press the soft reset button. Don't let go he camera button till you see the multi colored screen. connect your usb and run the current official T-Mobile ROM. If your lucky enough, your wing will be restored to a new factory default version. Let me know if it works.
thx DestructDez1
i tried to instal that rom (t-mobile) but nothing happen it just hang at 0% with an error (error 300)
any help plz?
Sorry, I think thats an unrepairable hardware problem.
can the goldcard help me?or there is no hope
daywalker_7780 said:
can the goldcard help me?or there is no hope
Click to expand...
Click to collapse
I don't know much about the gold card. But at this point there really is no reason why you shouldn't try it.
hay every one who had my problem
i found the solution and my p4350 was alife again
plz just follow this link step by step and it will be good at the end
http://forum.xda-developers.com/showthread.php?t=417930
c u later guys
Hi all,
i have a problem with one device here - Orbit II.
It is stuck on booting WM with volume controls on the screen. Usually it's not a big deal and can be solver with HR or by flashing a new rom, but the problem is that i cannot get it to do a HR: white screen with warning appears but when i press send buttong(the green one) - nothing happens, it doesn't react at all.
Ok, i was thinking to flash it, but another problem appeared: i can't enter bootloader(2 softbuttons+reset), same procedure works fine on my own device but this one just reboots and no bootloader...
I'm kinda out of options now.
Any help is appreciated.
Magnus23 said:
Ok, i was thinking to flash it, but another problem appeared: i can't enter bootloader(2 softbuttons+reset), same procedure works fine on my own device but this one just reboots and no bootloader...
I'm kinda out of options now.
Any help is appreciated.
Click to expand...
Click to collapse
press & hold camera button and make soft reset...
Thank you for the answer but i as said in first post, i have tried this, the white screen with the warning appears but pressing Send button does nothing, device does not react to this, so hard reset doesn't happen.
If someone could point to me any other way to enter bootloader - i can work my way from there.
I have also tried MTTY but USB connection doesn't appear in the list(yes, i have killed the activesync processes).
which screen
1st,
2nd, radio protocol version
3rd gif splash
4th wimo load screen
And also what rom have you got on atm.
It is stuck on 4th wimo load screen.
I have no idea about the actual WN version as it's not my device, but i assume it's the original O2 rom since there is still O2 splash screen.
Magnus23 said:
It is stuck on 4th wimo load screen.
I have no idea about the actual WN version as it's not my device, but i assume it's the original O2 rom since there is still O2 splash screen.
Click to expand...
Click to collapse
o well then i take its not hard-spl'd in which case i really do not get it, i have got into bootloader at the radio version screen so i dont get this one?? Is it still covered by o2 warrenty, it is 2 yrs long so best bet go to them and see what they say...
Thats if it has no hard-spl... If not take the battery out for a day and see if that brings it back to life, stranger things have happened seen that solve quite a few problems.
Well, device is not mine, a friend asked to look at it. I don't think he got a warranty left.
Well, the thing is, its not a big deal realy, it's not bricked or anything, i just need to get into bootloader, from there i can flash hardspl and the rest from SD... i just haven't seen this thing before... unable to enter the bootloader.
Is there any way to force the device to enter bootloader? I mean other than the standart procedures of Camera+reset?
I think i've seen somewhere a CustomRUU that could do that, even with incomplete WM boot. Like send some commands to the device to enter bootloader.
Does anyone know anything like this?
I installed maglar 1.12 on my hd2 using the nbh file method... now my hd2 wont turn off it just restarts as soon as you turn it off or put the battery back in.... when in magldr the button lights flash repeditally.... I can still flash roms using maglr usb method but when the roms are booted up the button lights are on constantly even in sleep, it seems to recive random input, and you cant put it in sleep mode and when it goes into sleep mode naturally you cant turn it back on........ My first thought was to try and to go back to stock but because I dont have a windows mobile rom on I cant use the active sync method and for some weird reason it wont go to the bootloader(yes I know how to get to the bootloader I am not and idiot)........ so I am stuck and dont know what to do
nchar123 said:
I installed maglar 1.12 on my hd2 using the nbh file method... now my hd2 wont turn off it just restarts as soon as you turn it off or put the battery back in.... when in magldr the button lights flash repeditally.... I can still flash roms using maglr usb method but when the roms are booted up the button lights are on constantly even in sleep, it seems to recive random input, and you cant put it in sleep mode and when it goes into sleep mode naturally you cant turn it back on........ My first thought was to try and to go back to stock but because I dont have a windows mobile rom on I cant use the active sync method and for some weird reason it wont go to the bootloader(yes I know how to get to the bootloader I am not and idiot)........ so I am stuck and dont know what to do
Click to expand...
Click to collapse
what happens when you try to go to bootloader?
Bro, try flashing any windows mobile 6.5.* rom on your hd2..
To do so, enter hd2 in bootloader mode,
Keep pressing DOWN + POWER when device is switchd off initially
and flash any rom.
This will surely help you
orangekid said:
what happens when you try to go to bootloader?
Click to expand...
Click to collapse
Yes what happens when you try to boo into bootloader?
strange mate!!!
when you ask for help be positive!!!!
use wise words....i stood 5 min to reply u or not!!!
because no one is an idiot on XDA,....
flash radio 2.15 first!!!
if ur phone want work
than
flash from SD card your custom rom 6.5 (search for the steps on xda)
your phone want start for sure!!!!!
but you will get back you bootloader back
1-HSPL
2-T29
3-Mag-loader 1.13
4-flash radio 2.15
5-flash your ROM
nchar123 said:
I installed maglar 1.12 on my hd2 using the nbh file method... now my hd2 wont turn off it just restarts as soon as you turn it off or put the battery back in.... when in magldr the button lights flash repeditally.... I can still flash roms using maglr usb method but when the roms are booted up the button lights are on constantly even in sleep, it seems to recive random input, and you cant put it in sleep mode and when it goes into sleep mode naturally you cant turn it back on........ My first thought was to try and to go back to stock but because I dont have a windows mobile rom on I cant use the active sync method and for some weird reason it wont go to the bootloader(yes I know how to get to the bootloader I am not and idiot)........ so I am stuck and dont know what to do
Click to expand...
Click to collapse
People he can not flash anything having to do with flashing via the SPL bootloader, this is why Orangekid and I both asked what happens when the OP trys to boot into bootloader.
calm down everyone!
lol
sorry, like others have mentioned, what exactly happens from start to finish when you try and get in to the boot loader, yes i know you said you know how to do it
but humour us, start to finish, buttons you push, whats on teh screen, everything.
sounds like something in the SPL has been screwed, been a lot of that recently which is a bit odd.
I can not get to the bootloader
I know that I cant get to the bootloader I tried the way you said above again and it just goes stright to magldr so I can not flash back to stock ........ I took it to a phone repair guy who said he fixed it and it appeared like he did but then two hours later it started again .......
Here is a video of my phone
*htt*p:/*/ww*w.y*ou*tube.c*om/watch?v=U7h3flLrE5g** I put the stars because I can post links right now but this is a video of my phone
nchar123 said:
*htt*p:/*/ww*w.y*ou*tube.c*om/watch?v=U7h3flLrE5g** I put the stars because I can post links right now but this is a video of my phone
Click to expand...
Click to collapse
Ok everyone as you can see he can not get the SPL bootloader to come up.
I will help you out with your Youtube link too.
I am very sorry to tell you but without being able to get to the bootloader you can not flash a official ROM back to the HD2 so you can not send it in for warranty exchange our repair. That is unless there is some miracle program out there that you can run from your computer to force the bootloader to bootup, which i have never heard of one. (Note to Devs that would be a awesome program to create if it is possible )
There is the bootloader.exe but you already have to have a Sync type connection for it to work and i don't know if the connection you get using Zune is enough. I attached the a EnterBootloader.zip file but like I said i don't know if it will help you are not. Try connecting and syncing your HD2 with Zune and then try to run the EnterBootloader.exe from your computer and see what happens.
Thanks for the program but when I try to run it in windows phone 7 it gives me the error that it is not a valid windows phone 7
Is there a way I could update or change magldr without the bootloader? or is there any sort of windows mobile rom I could install through magldr like you would with android or wp7?
I mean sorry it gives the are that it is not a valid win32 aplication not windows phone 7 that was a typo
nchar123 said:
Is there a way I could update or change magldr without the bootloader? or is there any sort of windows mobile rom I could install through magldr like you would with android or wp7?
Click to expand...
Click to collapse
Was shocked to watch your video !!
there is no way to flash windows 6.5 roms directly through MAGLDR..
would suggest you to get HD2 to nearby mobile repair center, hopefully they can help you out
Do you know of one around san diego or a place that could do jtag?
nchar123 said:
Do you know of one around san diego or a place that could do jtag?
Click to expand...
Click to collapse
I know someone in that can JTAG your HD2 buit he lives in Texas, but he is very good and experienced with JTAGing HD2s, PM me if you want more info as it would be against the rules for me to provide any other information in the forums.
Also I do not think you need JTAG but just need your voulume rocker fixed, but he is still the guy to do it.
the volume buttons should be easy to test within windows its self
I doubt its MAGLDR issue, it looks like an SPL issue.
could you tell me how much the jtag would cost and the volume down and up buttons work when the wp7 build is up