Hi to all professionals... i would seriously need your pro advise and comment how to resolve my phone problem.
i have recently bought a used HP ipaq 6965 however i have encounter some serious problem when i tried to upgrade the Rom to latest firmware.
The latest firmware is 1.21 from HP official. Here's the symptoms of my phone:
1) It keep on remain in HP startup screen (booting always)
2) Boot loader mode is accessible
3) USB is recognize and detected by windows XP
4) Soft and Hard Reset could be apply
5) update successfully wireless Rom by HP tool even the phone can only switch from HP startup screen and Boot loader screen
PRoblem:
1) active sync could not detect my phone no matter what i have tried.
2) How can i fix this non-detected device problem?
3) How can i re-upgrade my Rom if i could not connect phone thru my PC?
4) Is that any available solutions for me to upgrade and solve the problem
Thanks is advance.
Best Regards,
Related
Hi!
i was upgrading my universal's rom(downloaded from imate). And it said there was some connection problem, and asked me to restart the upgrading process but still it replied with the same problem. Now my Universal is stuck up on bootloader displaying serial and v1.01 . If you insert a usb cable it says usb v1.01. Nothing is happening if i restarting my device, SOME ONE PLEASE HELP?
Is this your first upgrade? Have you looked at any threads on upgrading? I direct you here... http://forum.xda-developers.com/showthread.php?t=290234
If you're still stuck after those posts, then please do post, but I think at this stage, the search button should really be the most useful solution
Dear..
You have just to install JASJAR_BL1.01_RUU_v1.2 (the boot loader) , and everything will be fine
1. connect your pocket to the computer
2. run the boot loader
3. click upgrade
4. restart your pocket
everything will be fine...
Hello everyone.
I recently got this 4 years old MDA 2 from a friend.
I thought i could still use it for Navigation and so i tried to update the Software to a newer Version - But somehow the update faild :-(
The only thing i see now on the screen is "Serial v1.02".
I already tried to switch into the Bootloader Menü for a Update via SD Card by pressing the Power+Navpad+Reset Switch, but it doesn't work.
Can someone help me please
bootloader
The device allready is in bootloader mode reconnect it to the pc and update the rom again then it will work again i use the aku 3.5 sp2 rom see the upgrading part in the forum
Good luck
Thanks, now my PPC is alive again.
Guess the Problem was with the new Vista Mobile Device Center.
I tried the same on a XP Computer with Active Sync 4.5 and it worked.
hey guys, over the past few days ive had battery problems with my iMate JAMin, i got a new battery, insert it, and power on my device, now, rather than loading up the iMate image, it goes to the tri-color boot screen, i've tried a Soft and Hard reset, no luck , any one willing to try and help solve this problem, please email or PM: [email protected]
Will installing a new rom fix this problem?
Aidenkidd.
From the wiki:
wiki said:
If during an upgrade your Prophet fails to start properly or can only enter bootloader follow this:
Recovery
Download and install the latest version of ActiveSync (Google for it)
Download and unzip an AKU2.2 (No Vendor) ROM for the Prophet-any AKU 2.2 will do-from
here (any part one) or
here
Within ActiveSync DISABLE connect through USB (Tools->Connection Settings->Uncheck Allow Connect through USB)
Put the Prophet into bootloader mode (hold the camera button and insert the stylus into the larger hole next to the power socket)
Plug the Prophet in via USB
Run the RUU specific to your device (G3 or G4) from the AKU2.2 folder
Disconnect the Prophet, and then re-enable the connect through USB.
Your Prophet should now work!
Click to expand...
Click to collapse
I wrote it any way, but since no one reads it I may as well post it here.
Few days ago my Wizard died all of a sudden. When turned on it only gets to the point when it shows "HTC smart mobility" and stays there. So not even to the screen with IPL, SPL. I tried soft/hard resetting, playing with battery but it was all no go, same.
I can get to the red-green-blue bootloader screen however, shows IPL 3.08, SPL 3.08. If i connect via USB cable to computer, bootloader screen shows "USB" on bottom. The ROM on the device was TNT's (not sure which version), Windows Mobile 6.1. It worked for ages without any problems with this ROM before this.
ActiveSync does not recognise Wizard at all, I cannot establish connection and therefore downgrade/upgrade the ROM becouse upgrade programs (for exmaple with ROM got originally with the device) say they cannot contact the device.
What are my options, please help.
hy
in my opinion , it is normal for active sync to not recognize your phone , because it's not turn on properly ,i mean it only recognize the phone when you enter windows mobile.
if i were you i would try to flash any rom i like and see if it works. i hope this helps
But ROM upgrade/downgrade program requires ActiveSync connection to run and I can't establish it...How to solve the situation, please advise?
when you are in bootloader screen and your phone is connected to the pc by usb cable just start the downgrade/upgrade program and it should work.
i did that. rom update utility complains that it cannot connect with mobile...
that was tried with:
1. official t-mobile ROM that was on the device when I got it
2. CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE ROM
my IPL and SPL versions now are 3.08
sorry , i can't think of anything that might help you.
same problem
phones a brick.
I can get to the bootloader , i can even perform a succesful hard reset.
But it doesnt get recognized by the computer in bootloader mode. is there any way to flash the rom if the computer doesnt recognize the device?
regards
Try this look for nbd v8.1 or v8.3 .
hold the camera button and do a soft reset but keep holding the camera button until the 3 color screen comes up it should sync your phone then run the nbd rom or original cingular ship rom like this one ** RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 ** i prefer original then other but that's me. Hope this help you.
I have a problem with my I-Mate JAM, It loads the OS.. but after everything Installs it converts to the BootLoader screen, and remains unuseable.
If I rest the phone, it loads straight to the Bootloader screen, but if I take off the Battery cover, leave it for a few seconds, then replace it and turn the phone on... It will load the OS setup again, but go back to the BootLoader.
So how can I fix this, and what must I do? Please help me ASAP. The Rom/OS is Windows 2003 SE.
Thanks
Sikuri
try flashing the ROM to a latest windows mobile, i encountered this problem on my HTC Magician, i downloaded the compatible and latest windows mobile for my phone extracted the files on my PC and while my phone is in boot loader mode i connect the USB to pc cable (you'll notice the serial changing to USB) after that i run the update.exe on the files i extracted and just follow instructions on the updater. And now my phone is fix. Hey im not an expert on this, I got thru it by reading the forums here, and there are more experienced experts in here that you can ask. Hope this helps and give you an idea. By the way run the update.exe on a Windows XP machine for it to work perfectly.