Hello
PPC: Blue Angel T-Mobile GER
Rom: Xplode Wm6.00.00.WWE
Radio:1.15.00
Protocol: 1337.45
From this rom i want to upgrade to Wm6.1 from Xplode.
My Upgrade steps:
1. Bootloader
2.The ppc shows "Serial"/"Usb" and "v2.05"
2.2 Kill Active sync
3. starting MaUpgradeUt_noID
4.MaUpgradeUt_noID gives no informations about the current Rom /upgrade rom
5.Next
6. Error 150
What i have to do?
Plx help me
Sry for my bad english!
Thx to all
It must be an OS problem
Try using Windows XP rather than using Vista.
I got the same problem with my XDA IIs,
I tried it in Windows XP and successfully Updated to WM 6.1
i have Windows XP no Vista
Give it a try without killing ActiveSync on PC.
1. Put device in bootloader mode
2. Put device in the cradle
3. Start update program (wait till 100% and do not remove device out the cradle)
4. When update has finished, hard reset the device
- If you have a PH20B device such as MDAIII, QTEK 9090, XDAIIs, PDA2K etc, EITHER:
Quickly press "Record" & "Camera" before the versions appear at bottom right
OR press "Power" & "Camera" & "Record" buttons and Reset at the same time
- If you have a PH20B1 device such as SX66:
Quickly press "Record" & "Windows Media" before the versions appear at bottom right EITHER
OR press "Power" & "Windows Media" & "Record" buttons and Reset at the same time
You'll see three options on screen. You must change the second and the third to yes. If you are not developing/testing software you can disable the first debug option for better performance.(“Enable KITL” must be NO, “Clean Registry Hive” must be YES, “Format Storage” must be YES)
- If you have a PH20B device such as MDAIII, QTEK 9090, XDAIIs, PDA2K etc, use "Camera" and the "Record" buttons.
- If you have a PH20B1 device such as SX66, use "Windows Media" and the "Record" buttons.
Note: The "Record" button moves up and down the menu and the "Camera" button toggles Yes/No. When you're done, press the button in the middle of the D-Pad to continue booting.
- Press the "Mail" button. A white screen will show for 30 seconds, while it is clearing your device in preparation for the new ROM to start executing
When the bootscreen, aka. the colored stripes is displayed, wait more, you are booting. The welcome screen to set up your device will appear shortly ...
(if removed earlier) Put back your SD Card before you do the setup. This way the installation from the SD will continue after you have done the setup
5. Your upgraded ROM is now running!
Greets Rossi
Related
Hello
I want to upgrade my MDA3 from WM2003se to WM06.
After i have read the upgrade artikel, i have seen, that im must change this
"Enable KITL” must be NO, “Clean Registry Hive” must be YES, “Format Storage” must be YES"
And here is my problem, my 4 buttons (Mail, Explorer, Windows, ok) in front of the MDA are Defect. So i can´t confirm the Options.
Are ther other ways to do this.
MFG Kleinepelle
PS: I know my english is very bad
Logically if you map the mail button to any of the top buttons, that should work as BA still keeps the entire software prior to pressing mail button. However an expert should confirm. Dont take risk.
Upgrade without usable mail button
kleinepelle said:
Hello
I want to upgrade my MDA3 from WM2003se to WM06.
After i have read the upgrade artikel, i have seen, that im must change this
"Enable KITL” must be NO, “Clean Registry Hive” must be YES, “Format Storage” must be YES"
And here is my problem, my 4 buttons (Mail, Explorer, Windows, ok) in front of the MDA are Defect. So i can´t confirm the Options.
Are ther other ways to do this.
MFG Kleinepelle
PS: I know my english is very bad
Click to expand...
Click to collapse
Hi there ... I have the same kind of problem with my O2 XDA IIs Blueangel. The mail button along with the other 3 (home,ie,ok) are not working or not responding anytime.I was not able to upgrade my rom and format the registry hive
But then i found a much simpler way to do it..
Try the following to format your rom,clear registry hive and upgrade to a new rom-all this even with the mail button not working.
You will need the program MTTY(Attached with this post).
1) Kill activesync processes: Ctrl+Shift+Esc in Windows to bring up Task Manager. Kill wcescomm.exe and WCESMgr.exe (by selecting the task on the processes tab, and clicking the End Process button below)
2) Phone needs to be POWER + Record + Pen Reset and on Serial/USB screen. COnnect it to the PC, and it should show USB, with the backlight remaining off.
3a) Run mtty1.42.exe
b) Select USB from first list (where COM1 is displayed. Don't press USB button). If USB (or a list item containing USB) isn't in the list, then you have't connected to the PC properly.
(Leave default parameters: 8 bits / Flow Control NONE / Stop bits 1 / Parity None / Local Echo No)
c) Click OK
3) Run following commands:
[press enter first to get USB> prompt]
USB>
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
USB>set 14 0
HTCST ÚÈHTCEUSB>
6. type "task 28" to get your device formatted
USB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>
7. type "task 0" to ask your device reboot
USB>task 0
USB>
8) Exit the program, then re-hard-reset (POWER + Record + Pen Reset), leaving on USB screen in order to run ROM Flasher
9)Now be back to the Usb/Serial screen and run your favourite ROM upgrade-A clean installation
Please let me know if this worked for you too. I believe this was my great geeky work i did with my BA. Was so frustrated when the buttons were not
working.
P.S: This is not my own work. I got the Mtty app from this same forum and the steps too. I am terrible sorry if i have repeated a post or done something i should not
Thank you very much.
It runs very good.
MFG Kleinepelle
Great advice! this should be placed in the wiki as well
Thanks to you and to all others <ou mwntioned for this help. Dtipex
thanks, it works!
thanks, it works!!
crabiorc said:
Hi there ... I have the same kind of problem with my O2 XDA IIs Blueangel. The mail button along with the other 3 (home,ie,ok) are not working or not responding anytime.I was not able to upgrade my rom and format the registry hive
But then i found a much simpler way to do it..
Try the following to format your rom,clear registry hive and upgrade to a new rom-all this even with the mail button not working.
You will need the program MTTY(Attached with this post).
1) Kill activesync processes: Ctrl+Shift+Esc in Windows to bring up Task Manager. Kill wcescomm.exe and WCESMgr.exe (by selecting the task on the processes tab, and clicking the End Process button below)
2) Phone needs to be POWER + Record + Pen Reset and on Serial/USB screen. COnnect it to the PC, and it should show USB, with the backlight remaining off.
3a) Run mtty1.42.exe
b) Select USB from first list (where COM1 is displayed. Don't press USB button). If USB (or a list item containing USB) isn't in the list, then you have't connected to the PC properly.
(Leave default parameters: 8 bits / Flow Control NONE / Stop bits 1 / Parity None / Local Echo No)
c) Click OK
3) Run following commands:
[press enter first to get USB> prompt]
USB>
5. type "set 14 0" without the quotes to tell bootloader to boot the OS after reset.
USB>set 14 0
HTCST ÚÈHTCEUSB>
6. type "task 28" to get your device formatted
USB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>
7. type "task 0" to ask your device reboot
USB>task 0
USB>
8) Exit the program, then re-hard-reset (POWER + Record + Pen Reset), leaving on USB screen in order to run ROM Flasher
9)Now be back to the Usb/Serial screen and run your favourite ROM upgrade-A clean installation
Please let me know if this worked for you too. I believe this was my great geeky work i did with my BA. Was so frustrated when the buttons were not
working.
P.S: This is not my own work. I got the Mtty app from this same forum and the steps too. I am terrible sorry if i have repeated a post or done something i should not
Click to expand...
Click to collapse
very well explained . good job
Please where can i get Windows 6.1 on my VODAPHONE VPX (XDA, dopod, HTC - blue angel).Looking forward to hearing from you.
look here in sticky subjects for sun-dream,you will find it
since no one is replying, i do the job:
WM6.1 CEOS 5.2.20758 Build 20758 Aku 1.4.1 WWE
16MB RAMDisk,25.2MB PP
http://www.brsbox.com/filebox/down/f...and/1181621103
Password for extracting the rar file:
2qfewrwF$W%567%wwba
there is nk.nbf file in it, Extract it to C:\rom directory.
Now download BAA RUU (installation utility)
http://moeenweb.110mb.com/rom.zip and extract it to C: drive. (remember nk.nbf should be in rom folder in C: drive.
Now:
1. Take Mem card out of your blue angel
2. put blue angel in bootloader record + on/off button + reset
3. Connect it to usb cable
4. run MaUpgradeut_noid.exe
5. just clickity next next next and then finish after the update is complete
6. Now press reset button and sooner ur phone is resetted press camera + record button together until u get a 4 colour screen with a menu
do this press camera to switch options, press record button for yes/no
No for enable KTTL
Yes the other two options
press inbox button and u r done
I am beginning the process of documenting all things HTC Rose, rather than pointing to how other utilities & processes work for other phones and SHOULD work for this one. Everything I post here will be Rose-Specific, and I hope it helps. I am using the most extreme environment, including Windows 7 as the host PC, WM 6.1 on the phone...all other OSs should be cakewalk if my stuff all works. Coming very shortly (this weekend) will be:
- App Unlocking
- Entering Bootloader Mode
- Working with Windows 7 & WMDC (6.1 vs. what comes with Win7)
- Known ROM Images & FYIs
- Dumping a ROM for backup purposes
- Reloading a dumped ROM for restore purposes
- Tweaking your ROM for personal use only
How to enter Bootloader Mode (Tri-Colour)
- Turn off your HTC S740/S743 (either by removing battery or turning off)
- Hold down the VOLUME UP button (keep it held down)
- Turn on the phone using normal POWER button (no need to hold the power button...just a normal push and release)
- Phone will enter Tri-Colour/Bootloader Mode
example: my HTC S740, purchased as non-US phone, shipped with WWE Asian ROM (Hong Kong) via Expansys shows the following:
- ROSE 100
- SPL-1.54.0000
- MicroP-Rose (LED) v10
- MicroP-Rose (KEY) v5
- PCBID 0x80
- RID 0x0
WMDC and Windows 7 Pre-Release
By default, Windows 7 will ship with an integrated version of Windows Mobile Device Center (WMDC). The challenge most people have with getting this to work with their phone is this "not really WMDC 6.1, not a fully-finished Win7-WMDC" version. To get around this, keep in mind there are two primary scenarios when connecting a device to Windows:
1) Connect WM device to WMDC for the purpose of "syncing stuff" (aka USB Connected)
2) Connect WM device to WMDC for the purpose of low-level tasks (aka USB Unchecked)
*NOTE: the easiest, fastest and most accurate way to get all of this to work on Windows 7 is to do the "remove WMDC" steps in #1 below, and instead of working with your existing phone, simply do a Clear Storage, let the phone reset, and plug it in with a fresh WMDC. This just simply works, but I know not everyone is willing to reset the device....
To achieve #1, I suggest the following:
- Go to Add/Remove Programs and Uninstall WMDC (application AND Driver Update)
- From an administrative-cmd line, execute
reg delete HKLM\SOFTWARE\Microsoft\SQMClient\Windows\Disabled Sessions /va /f
- Go in Device Manager and remove any reference to a mobile device or RNDIS adapter. Reboot.
- On your device go to SETTINGS, then to CONNECTIONS, then the USB TO PC icon. Make sure the ENABLE ADVANCED NETWORK FUNCTIONALITY is UNCHECKED
- Manually delete the contents of the C:\Windows\WindowsMobile folder
- Delete the contents of the following Registry Keys:
HKCU\Software\Microsoft\Windows CE Services\PartnersHKLM\Software\Microsoft\Windows Portable Devices\Devices- Using Windows Explorer, delete all files in the folder C:\Users\<username>\AppData\Roaming\Microsoft\ActiveSync\Profiles
- Reboot your Win7 PC, ensuring the phone is NOT CONNECTED during reboot
- Install WMDC 6.1 from the Microsoft Download site (this ensures you are running WMDC 6.1 ON Win7 vs. Win7WMDC on Win7)
- Reboot your phone
- Open WMDC 6.1 on your PC
(Optionally....just do a Clear Storage on your phone a listed in the NOTE above to ENSURE this works simplest...if you have the option)
- Plug your phone in via USB, preferrable to a USB port NOT used prior....if possible
- Windows should reinstall your device drivers without failing and WMDC should connect ok this time
To achive #2, I suggest the following:
- Perform the steps in #1 first, to get WMDC installed properly
- Open WMDC & disable ALLOW USB CONNECTIONS
- Turn off your device
- Enter Bootloader Mode using VOLUME-UP + POWER ON
- Win7 should detect and install the additional drivers for NON-USB mode (separate from the standard sync device drivers WMDC normally requires)
it`s sounds ok
- App Unlocking
- WM 6.5
i`m waiting ...
would be nice.
can't imaging this is much different from the HTC touch 3g
Good stuff! I have my S743 app-unlocked with the old SDA-unlocker tool.
I remember that when the WM 6.1 wa about to be released the standard version was available way before the Professional... Anybody has any idea what non touch screen WM 6.5 is going to look like ?? and when we can exxpect it? Because the ROse is capable of running it I am sure...
For any rom development need hardspl
baliles said:
- Turn off your HTC S740/S743 (either by removing battery or turning off)
- Hold down the VOLUME UP button (keep it held down)
- Turn on the phone using normal POWER button (no need to hold the power button...just a normal push and release)
- Phone will enter Tri-Colour/Bootloader Mode
example: my HTC S740, purchased as non-US phone, shipped with WWE Asian ROM (Hong Kong) via Expansys shows the following:
- ROSE 100
- SPL-1.54.0000
- MicroP-Rose (LED) v10
- MicroP-Rose (KEY) v5
- PCBID 0x80
- RID 0x0
Click to expand...
Click to collapse
For my S22HT (ROSE110), to enter bootloader mode it's:
1. Phone off
2. Hold down VOLUME DOWN key
3. Keep holding VOLUME DOWN and press POWER until it turns on
hi
my name is shekhar
please get me wm 6.5 to my htc diamond
i want to upgrade from wm6.1 to wm 6.5
please
How to Install or Update your Windows Mobile?
Please Follow Below Orders :
Please Follow Below Orders :
1. you need a PC
2-1. If you have Windows XP -> Setup ActiveSync 4.5 from Here
2-2. If you have Windows Vista or 7 -> Setup Windows Mobile Device Center from Here
3.If you use manufactured ROM(Orginal WM6.1 ROM OR Official ROM) -> Install Touch_Diamond_-HardSPL_OILNEX From Here
How To Install HardSPL on Touch Diamond?
-> After Downloading and Extracting this file
you Must connect your Touch Diamond to your PC with its Cable
Let your PC Connect to your PPC with ActiveSync or Windows Mobile Device Center
Find HardSPL Folder and Run ROMUpdateUtility.exe
At Appeared Windows Page By ROMUpdateUtility.exe Accept Check Box and Click Next Button
Warning : Don't Unplug in Touch Diamond's Cable , Diamond's Battery Must be Charged More than 50%
Then you can see this Message on your PC->"verify the information on your PDAphone...Please wait"
After That you can see Setup Page on your PPC with 4 colors and on the White Color Part ,you can see USB (Notice : You can See Setup Page with Holding Sound Decreasing Button and Pressing Restart Button togather and Release Sound Decreasing Button Until Appearing That Screen)
Clicking Update Button And Next Button After That
And in Finally you can See Two Process Bars are Processing in the Same Time One of them on your PC and Another on your PPC and Restart your Device automatically.
I congratulate, your Touch Diamond Has Been Unlocked now you can install any ROMS That you Want
4. Downloading WINDOW MOBILE 6.5 WITH HTC SENSE 2.5 from Here ( you can See its Pic Here)And Extract this file
5. you Have this folder With two Files CustomRUU.exe And a File With NBH suffix , IF this Folder Dosn't have CustomRUU.exe Download it from Here And Put it to this Folder
5. Run CustomRUU.exe -> Keep Clicking Check Box Button and Next Button until Appearing That Message Again : "verify the information on your PDAphone...Please wait"
6. Clicking Update Button And Next Button After That
7. you can see again Two Process Bars are Processing at the Same Time On your PC and PPC
8. After Finishing ->your PPC Restarts Automatically Again And you Have WM6.5+HTC SENSE 2.5 ON YOUR TOUCH DIAMOND
9. Enjoy. (This ROM Has Been Made And Cooked by donsalari So Much Fast and Stable and Also Really Nice)
Hi guyz!
I have heard it said some of the ROM updates cause some technical failure...like GPS failure or G-sensor....
I wanna ask someone, who have tried this ROM if its ok and will not make any defection!
Thanks in advance!
workes great
Hey guys, I found how to upgrade the HP 6945 in a brazilian website and I tried, IT WORKS! I'll explain how to do so now that I can post URLs
First of all, and which is a bit difficult nowadays, you need to use Windows XP, I saw cases that the people have done the upgrade in a virtual machine, but it didn't worked for me.
Let's go to the specifications of your mobile: your Flash Type MUST BE G4 and your BootLoader MUST BE G.39 , if you don't know you can see that in your mobile "Start/System/HP Asset Viewer"
Let's start,
1. Connect your mobile by ActiveSync (you'll need the 4.1 version as your mobile is WM5) using the cradle/dock/usb (was recommended to do a Hard Reset, but it's optional. To do so press On/Off , Send and Cancel Calls buttons, then use the PEN (Stylus) to press the Reset button under the mobile)
ActiveSync 4.1 - http://www.mediafire.com/?blql91lb1cqfq5z
2. Download and extract the file "SPL vG.39.7z" - http://www.mediafire.com/?o243pua8x7c0j0h
3. In the "SPL vG.39" folder, look for a shortcut named as "Command Prompt" and execute it
4. Now write this line in the command:
pdocwrite spl -n0 -b 0x20000 0 0x80000
5. You'll receive in your mobile a message about a dll (itsutils.dll) Press YES.
6. Now you have to put your mobile in BootLoader mode. Press the two buttons next to the directional + On/Off + Reset (using the Pen[Stylus])
7. Now open the ActiveSync and go to "connection configurations". Deselect the box "Allow USB Connections".
8. Download and extract the file "6915_ENG.7z" - http://www.mediafire.com/?kgwl83e22e2oody
9. Open the folder and execute "Sable_RUU.exe"
10. Press Upgrade and WAIT for a message "Update finished!"
11. Go back to ActiveSync (now you should use the 4.5 Version), go to "connection configurations" and select "Allow USB Connections"
12. Enjoy.
Everything is working, and you now have a new Office Package, including OneNote.
Your calls are better, don't freezing. The only problem is that SMS don't do any sounds when it arrives, but it's just the SMS.
The bluetooth you'll need to go to the Settings/Connections for the first time to work, but it's just once.
I have all the downloable content, if the link don't work, email me.
The original Rom of your iPAQ you can be found at HP's website named as GSM Radio Firmware, if you want, but I don't mind you'll need it.
The original website is in Brazilian-Portuguese, I've just translated for you.
http://www.gsmfans.com.br/index.php?topic=202365.0
That's everything. =)