Database Users

The Solution to the GSM ERROR Issue.ON XDA (QTEK 1010)

Hello all.
i have been searching the forum for the solution of this problem, some guys suggested solutions that involve a file that is no longer available, upgrade.zip which is aparently a radio upgrade(or downgrade) made for the SD card (a startup.exe in a startup directory).
Well, having said that, i had to solve this problem last night, and here it goes.
after trying original ROM upgrades, all versions, 3.14,3.17,3.18~4.
nothing worked.
finally, i grabbed a copy of xda-developers's 1.1 ROM
and guess what!!!
the phone started up, gave me the screen allignment and the whole menu!
sure enough, ran file commander(that version did not have file manager) copied the RSU files over to the windows directory, and the exe file to the windows\startup and rebooted the phone.
it stopped at 1% again... NOW REMEMBER, i had an EMPTY BATTERY...
the 1% ERROR is a battery issue, that turnes into this issue when the modem upgrade FAILS.
so here is what i did. and you be the judge.
i ran active sync from the phone, and it did connect(while the upgrade program is still running) and left the room/
in 10 minutes i came back and the upgrade was completed, so here is what i think
i think that the RSU will still run if it was in the background!!! even with an empty battery(connected to the charger ofcourse.
i did not have much time to do anymore testing, but i am sure that someone with the same problem will make the time. the key from my experience is that the proccess will complete if it is in the background.
there u have it.
good luck.

i forgot to add that the upgrade i used was taken from yorch's page and it was the latest Tmobile, i had to downgrade later to an older version that i have to solve the network issue, but it was done(the downgrade) like a charm, i had a full battery then.
here is the Tmobile RSU link v6.24
http://www.yorch.net/downloads/ROMS/TMOradiostackupgradeR624 .zip
a 1.26 MB file.

Hi!
Now I'm taking a try (unfortantely I've found only the special edition rom 1.2).

No success with SE ROM 1.2. Where could I download 1.1 from? Found it nowhere.

One more thing: maybe the version of active sync counts? Mine was 3.8.

plg said:
No success with SE ROM 1.2. Where could I download 1.1 from? Found it nowhere.
Click to expand...
Click to collapse
http://lumpistefan.dyndns.org/tools/special_rom_1.1.exe.zip
HTH
Stefan

LumpiStefan said:
plg said:
No success with SE ROM 1.2. Where could I download 1.1 from? Found it nowhere.
Click to expand...
Click to collapse
http://lumpistefan.dyndns.org/tools/special_rom_1.1.exe.zip
HTH
Stefan
Click to expand...
Click to collapse
Thanks, Stefan! Maybe this one will help...

Hello to all, and mr stefan,
I upgrade my qtek 1010 with SFX56 windws 2003, it also upgraded my RSU, which is not working in Middle East. Kindly advise me how to downgrade or upgrade with other RSU. Thanks

your problem is in the network selection, search the forum for the proggy that changes it from 1900 to 900 and you should be OK.
i hate telling anyone to search i know how hard it is, but i do not have a clue where the proggy is, meanwhile, if i run across it, i will point it out,
if not, go to the bootloader, select GSM and change it from there, you will loose all data so backup first,
Good Luck.

search for "bandwith switch tool"..... good luck.

here it is on wiki
http://wiki.xda-developers.com/index.php?pagename=BandSwitchTool
tell us if this fixes your problem.
if not, you will find links to radio upgrade on
[/url]http://lumpistefan.dyndns.org/tools/ thanks to LumpiStefan
for a great resource.
good luck.

never knew you can post as guest
well, again, let us know what happens.

hi all
I just picked up a XDA from a guy who screwed up the radio stack upgrade (it cosy me @$80 USD ) and im now on a mission to fix it...
using your advice I used the XDA developers rom 1.1, this got the phone to start up with the working today screen and menus etc....
I install/copy over the new RSU upgrade files over and reboot
but here is where i get a bit stuck...
I cant get into active sync fast enough before I get the 1% RSU upgrade error, so the upgrade wont run in the background, it just sits there....
how do you get into active sync before the error comes up?
cheers
MADMAX

Error: remove programs..." x was not completely removed

I tried to install ClearVue PDF from the O2 supplied CD and it failed (with error messages in German!) - however when I tried to 'remove programs' I get the above message and ClearVue is still listed under programs. Ditto with Skype. These are the only 2 things I have added since switching my XDa mini s on for the first time. How should I uninstall these properly....so I can start again! Thanks

Well if you want to install it. Try installing it again. Then if fails again download the latest version of it from their website and install that. Hopefully you will have the registration key installed and it will work. Otherwise you will at least have an English error message.

Thanks
I'll try the web site - looks like I can't just download ClearVue - does it all come witin the 'software update' bundle?

No no no! ;-) The Clearvue website http://www.westtek.com/pocketpc/pdf/ As long as the install you have made registered it the trial version will be installed as fully operational.

Thanks
I'll have a go...

Sometimes a program wont delete because its running. make sure you have nothing running before removing it

Is this not an issue with the persistent memory in the Wizard? I've never been able to uninstall things, always comes up with that error, but installing an AKU 2.3 ROM seems to have solved the problem.

I think it's a persistent issue - I've tried every way of uninstalling (from Xda and PC via ActiceSync etc) and ClearVue is still there (and not working). However last comment slightly too techy for me (sorry - just a user....)? Is this an OS upgrade....?

The ROM is an OS upgrade, read all about it here:
http://forum.xda-developers.com/viewtopic.php?t=53954&highlight=
Whether the newer ROM solves the problem, someone better informed than me will have to tell you. It may just be coincidence that I can now uninstall programs properly??

paulrockliffe said:
Is this not an issue with the persistent memory in the Wizard? I've never been able to uninstall things, always comes up with that error, but installing an AKU 2.3 ROM seems to have solved the problem.
Click to expand...
Click to collapse
Same here, ever since upgrading to AKU2.3 i haven't got that uninstall error *Knock on wood*

Compact Framework

Tried installing PocketSheild, and get an errormissing method exception this app requires a newer version of MS.net compact Framework than the version instaled on this device (?? the phone is only 3 weks old ??)
How do you find which version is on the phone? Whats the implications of installing a newer version (and which one do i choose!)?
thanks

\windows\cgautil.exe will tell you. I think WM 6.1 only comes with CF2.0 by default, although HTC certainly could have put CF3.5 in their default installer software (stuff that installs once only after a hard reset). I can't tell whether mine did this or whether I did it by hand. Nevertheless, you should be able to download/install it from here: http://www.microsoft.com/downloads/...49-3C6B-42F1-9FD9-0041345B3385&displaylang=en. There should be no issue installing it side-by-side with 2.0.

thanks, managed to downoad it, but how do you install it?

If you don't use Activesync, you may want to get just the cab file instead. Just google for NETCFv35.wm.armv4i.cab, then instal like any other app, to the main memory.
Also, whilst you're about it, google netcfcfg.cab. This app lets you set windows CF policy, so that all apps which need CF2.0 to run will automatically use your newly installed CF3.5, which is apparently better and more stable.
The file sizes should be 2644KB and 34KB respectively.

wsb_champ said:
thanks, managed to downoad it, but how do you install it?
Click to expand...
Click to collapse
Run it on your PC and then next time you connect your device via activesync, it will push and install the CAB on your phone. Well, that's the idea anyway..

.NET 3.5 probs still not solved
Sorry, but I dont have any idea how to solve my problems.
there are several apps (.cabs) which I cannot install on my device, neither on internal nor on external (sd-card) memory.
the device (htc 3600) still keep answering: this version is still part of the ROM.
but I stay with my problems and dont wont to risk a HR.
Any Ideas?
thxs in advance

seeraeuber said:
Sorry, but I dont have any idea how to solve my problems.
there are several apps (.cabs) which I cannot install on my device, neither on internal nor on external (sd-card) memory.
the device (htc 3600) still keep answering: this version is still part of the ROM.
but I stay with my problems and dont wont to risk a HR.
Any Ideas?
thxs in advance
Click to expand...
Click to collapse
Try the HTC 3600 forum section, I guess they might know more relevant information. http://forum.xda-developers.com/forumdisplay.php?f=313

cheers!!!
works just fine. copy NETCFv35.wm.armv4i.cab, install, soft reset and you're ready to go. Thanks!!!

Can't seem to install anything on ATT Pure...

I can sync and copy files like several of the cabs from this site to the phone Storage card or My Documents in the phone and when I try and run any of them I always get an Unsuccessful .
is the ATT Pure Application locked? I did notice that all the applications I am running are not digitally signed or signed by a trusted provider and the phone complains and ask if if I still want to run. I pick yes and it still fails.
Any thoughts? I know some of you have ATT Pure devices!

FIXED
I did this and all is working...
1. Deleted my partnership with my laptop (Win 7 64bit)
2. boot my ATT Pure
3. Connect but dont establish partnership
4. copy over the cab files you want
5. use file explorer on the Topaz (Pure) to run them
6. all works fine!
7. loading EnergyROM now
the lesson to be learned if it does not work for you and it works for everyone else then go back to the basics!

Welcome to AT&T... yes all branded phones are app locked because they want to force you to use their apps.
You can app unlock it using a cab install... but some new phones are even rejecting that.
Official and Custom roms are the way to go. I recommend everyone with a Pure to at least flash to the newest Official WM6.5 build. It will work just the same but be clean of AT&T junk.

I have an AT&T Pure
I have no particular problems with installing Cabs
As another poster said copy the cab to a temp directory
and run it from File Explorer (delete the cab to save space after its been run)
Or you can use "CabviaActivesync" availabele on this site which makes it a little bit easier. (but I did have two cabs that had bad setups and needed manual install)
Bottom line the PURE does not block most cabs (I've tried)
(I only had a problem with the write protected weathercity database now ok)
Chances are something is wrong on your Pure or your method
To the senior poster that replied
Hey I've made tweeks and played with the stock ROM
I'd love to clean the bloated and unused ATT aps
incorporate weather into the clock ( TF3D 2.5+++)
and get a cleaner start menu (too many aps)
and certainly see an improvement in performance and snappiness
Id love to try a new ROM
but most new roms are written for Diamond2/Topaz
I'm not clear if the radios are the same on the the D2 and the Pure?
Can I burn WM and TF3D without affecting the radio part of the code?
Are the any other issues we need to be aware before we burn a new Topaz rom
onto an ATT variant of the Topaz ?
Is there a copy of the original Pure Rom available in case we need to return
it to ATT (what else would we need to insure we could return to ATT to fix any other later warrenty covered problems)
Of course I realize there is a risk invilved,
but whats the best safety prep?
I'm new to phones but an old micro hard/firm/soft ware and PPC guy
Thanks in advance
KJL

I haven't had a single problem installing anything on my stock Pure. Even software that normally requires an app-unlocked phone installs just fine.

I'm also curious about what Kenn asked. I'm getting a Pure tomorrow and I won't be able to get the crapware off there fast enough.
Specifically, can I flash the official HTC 6.5 rom to the Pure without having to hard spl? Is is just a straight flash?

I have the same problem with this ROM: http://forum.xda-developers.com/showthread.php?p=5743820#post5743820
Everything is OK but installing the cabs.
When I try to install any cab it wrote me "Instalation of ... was unsuccessful."
I tried a lot of cabs and all of them are the same
Any help please?

.
This particular problem gave me 4 day headache last week when i couldn't figure out why I couldn't HSPL my Pure. Had to Hard Reset entire phone, everything worked

Yes, I also hard-reseted my phone yesterday and everything works now!

HD2 certificate/component problem

Up until a few days ago, my HD2 was working fine. Then I tried to install Android. I used the one that you just copy to the storage card and run a file called zharet.exe ( !!NOT HARET.EXE!! ). I think it was Cotulla's ROM. First time, it crashed. Second time, meaning after I installed Radio ROM version 2.12, which is required (more specifically, 2.08 or above is required, but 2.12 was easier to find), it started and installed, then rebooted. Third time it worked and was able to send a text message to my stepfather. I switched back to WinMO to ask him if it got there, then I started Android again. It crashed, sending me to the boot screen of WinMO. Upon this start I was no longer able to run many files (executables), the running of which resulted in the message "The File *PROGRAM NAME* cannot be opened. Either it is not signed with a trusted certificate, or one of its components cannot be found. If the problem persists, try reinstalling or restoring this file."
I have tried numerous fixes:
Soft reset
Reinstalling the applications
Seeing if .NET Compact Framework was installed; the phone claimed it was, but I couldn't find any trace of it and so I tried to reinstall it. I was not able to, so I "uninstalled" it from the phone, which still thought it had it; the operation took no time, so I doubt it was there in the first place. When I tried installing it to the phone again, it said that this version was already in the ROM. Also tried installing an older version of the CF, but it just said I had a newer version.
Switching memory cards (3 different ones)
Renaming the memory card and restarting, a fix recommended to some other people who had a problem with similar symptoms. It refused to cooperate and said that the memory card could not be renamed.
My next step will be to rename the memory card using a device other than the phone itself.
I don't want to hard reset as I wish to keep my messages and contacts, but if that's what is needed to "un-half-brick" this phone, I will of course do it. The way it acts now, I might as well have kept my n95.
It is worth noting that HardSPL should be installed, as it was required for the Radio ROM flash.
EDIT: HardSPL install IS verified, boot screen reads as follows:
PB81100 HX-BC
SPL-1.42.HSPL XE
0x05
CotullaHSPL 0x30
In this thread, Gargoyle999 is describing my exact problem: forum.ppcgeeks.com/showthread.php?p=1882858
Keep in mind that this phone is Norwegian with Telenor as its carrier, although the phone itself is not locked and capable of using any carrier.
EDIT: The files that may not be run are mostly third-party ones, like MorphGear, zharet, Google Maps and so on. Most programs that came with the phone, like Copilot, Footprints and Opera work.
I am not too familiar with XDA, so forgive me if I am posting in the wrong section or making some other rookie mistake xD

I am having the same issued on one of my HD2's...anyone??? Help!!!!

This is NOT and android problem.
I'm not exactly sure, but it's a security measure in WinMo that disallows unsigned programs from running after the system has crashed due to those programs running, probably to protect the system from malicious programs.
All you need to do is disable security on it. There are various thread on this site in different places that tell you how to. Personally, I found the mobile security configurations manager(windows) is the best way. Just plug in your phone in WinMo, using activesync, open the program, and load device. Then you can just select no security, and provision it. It'll overwrite all the proper registery settings and whatnot for you.
Also, GOOGLE IT. I found all this information myself just by searching "Either it is not signed with a trusted certificate, or one of its components cannot be found. If the problem persists, try reinstalling or restoring this file" +windows mobile 6.5

Yes, yes Google it...I understand...But guess what? I did and found the same utility. And guess what? I got another error when it tries to install a cab file on the phone and for whatever reason the cab file errors out...I came here after reading and trying a ton of stuff and happened upon the OP's topic today.
Another thing is I realize it may not be an Android specific problem BUT prior to installing the mattcfroyo build and then attempting to test another build I didn't have any issue installing a cab file from the SD card. Also before anyone offers about installing another SD card I tried that also and no haps.
Weird and I am still searching for a solution but again XDA is the spot and researching here has not provided me with a working solution as of now....sssooooo...HELP!? Or not...

lstrike said:
Yes, yes Google it...I understand...But guess what? I did and found the same utility. And guess what? I got another error when it tries to install a cab file on the phone and for whatever reason the cab file errors out...I came here after reading and trying a ton of stuff and happened upon the OP's topic today.
Another thing is I realize it may not be an Android specific problem BUT prior to installing the mattcfroyo build and then attempting to test another build I didn't have any issue installing a cab file from the SD card. Also before anyone offers about installing another SD card I tried that also and no haps.
Weird and I am still searching for a solution but again XDA is the spot and researching here has not provided me with a working solution as of now....sssooooo...HELP!? Or not...
Click to expand...
Click to collapse
Look up all of the google registry fixes, and try every single one of them.
If none of them work and the program I recommended doesn't work, backup and hard-reset.
then, when it's done first thing use that program to disable security.
Also, most custom ROMs have security disabled by default.

Well I just went ahead and flashed a new rom and I am good to go...

I have tried your application. Got the same results as lstrike, error when installing CAB file. Also, how am I supposed to edit the registry when I can't run third party programs?

Will flash Miri's ROM soon. Any idea of whether or not that one has security disabled by default?

sigh i got the exact same problem after trying to run andriod.... any luck?

same problem here, did anyone face the problem then resolve it?

I found the solution !
When the error appears just go to marketplace, download the free version of Resco Explorer
(Resco was the first official registry app I found but if there's another in marketplace i guess it will do just fine)
After this open Resco Registry (included in Resco File Explorer) and go to
HKEY_LOCAL_MACHINE\Security\Policies\Policies
Then go to 0000101a and change DWORD Data value to 1
Now every thing is perfect and you can open all of your apps
Good luck !

Thank you, this solution saved my day!
Rat01 said:
When the error appears just go to marketplace, download the free version of Resco Explorer
(Resco was the first official registry app I found but if there's another in marketplace i guess it will do just fine)
After this open Resco Registry (included in Resco File Explorer) and go to
HKEY_LOCAL_MACHINE\Security\Policies\Policies
Then go to 0000101a and change DWORD Data value to 1
Now every thing is perfect and you can open all of your apps
Good luck !
Click to expand...
Click to collapse
Excellent! great work, thank you!

Rat01 said:
When the error appears just go to marketplace, download the free version of Resco Explorer
(Resco was the first official registry app I found but if there's another in marketplace i guess it will do just fine)
After this open Resco Registry (included in Resco File Explorer) and go to
HKEY_LOCAL_MACHINE\Security\Policies\Policies
Then go to 0000101a and change DWORD Data value to 1
Now every thing is perfect and you can open all of your apps
Good luck !
Click to expand...
Click to collapse
Thank you!