The battery came out will the device was connected to the computer via usb. Don't ask how I was messing about, the back came off and then the battery fell out. Now I can't turn it on. When I plug into the mains adaptor the charge light does come on. Any ideas.
Thanks
try to set the device in BOOTMANAGER mode and see if you at least can access that part of the phone!
What did you do when the battery 'came off'? Flashing it?
If you did not flash it press and hold the power button and remove the battery. Keep pressing the power button for an additional 15 to 30 sec after you removed the battery.
Leave the phone without the battery for half an hour or so, then press and hold Power for 30 sec. While still holding the power button place the battery back in, release power, wait 10 sec and try to turn it on ...
Thanks very much for your reply. I had just flashed it. It had rebooted and hung on the splash screen. I then picked up the phone and accidently knocked the battery out. Do you think this makes a difference to your suggestion?
Tried your technique but nothing unfortunately. It may be dead!
Thanks anyway.
Maybe my phone is dead too
I did the same with my phone...just did a flash and rebooted and now freeze on the splash screen...what can i do to save my phone?
If you're phone still turns on and just hangs at the splash screen as far as I understand you can then hold down the camera button and press the soft reset key. This should take you into the bootloader. From there you can re-flash the device with a different ROM like 'Wizard Love' (you can find it on this site somewhere, use search) or download the latest ROM from your provider. Use a NO_ID flash utility which means you don't have to have Activesync 'active'. My problem is slightly different as my device won't turn on at all. I've just bought a replacement battery just incase thats the problem. Otherwise I guess its gone for good.
If the flash finished successfully you can try first:
HOLD CON KEY (left side of the phone) + VOICE DIAL KEY (right side of the phone) + RESET. This will HARD RESET your device and re-initialize the ROM - might be that that can fix it! If not try to reflash it with the shipped ROM
BOOTLOADER MODE:
Power button + Camera button + Reset.
Junner2003 said:
If the flash finished successfully you can try first:
HOLD CON KEY (left side of the phone) + VOICE DIAL KEY (right side of the phone) + RESET. This will HARD RESET your device and re-initialize the ROM - might be that that can fix it! If not try to reflash it with the shipped ROM
BOOTLOADER MODE:
Power button + Camera button + Reset.
Click to expand...
Click to collapse
Thanks for the bootloader info....I had totally messed up my 8125 earlier...and now its back!!
THANK YOU!!!!!!!!!!!
Hi,
I have got my trinity phone one year ago and never had a problem since last week. When starting my phone, it stops on the first screen (with "orange" logo) and nothing more happens.
I tried to reset it without succeed. The phone is not detected by the "activeSync" to make it flushable.
Help please !
Yves Florent CK
my problem is mor or less the same... only that dont apears any image on screen and the green led is constantly on...
I have loaded a long time ago an old version of ROM Gelly.
This ROM worked perfectly to a friend who suggested to do the same with my trinity.
The PROBLEM is that when i try to open the pda it freezes to the first srceen showing the rom version and after....nothing!
I tried to load again Gelly from the bootloader, it begins to run, it runs about 1% then the trinity makes a flash (this means it loses the connection with the pc) and then shows me again the first screen....
Please i need help!
me to. i try install the rom original and my pda is living again.
try this to
hi,
2 things ...
have you tried a hard reset ? (hold both softkeys & hit reset button)
and when flashing:
when you first run the rom upgrade from PC with phone on Activesync, it is quite common for phone to hang at the bootloader screen ...
worry not -
just re-run the upgrade from PC again immediately, without disconnecting or attempting to switch phone off.
(the word USB should be visable on device under the coloured bars)
if you do get hung up at bootloader screen a hard reset should at least get you back to where you were, and you can try re-flash again.
hope this helps,
regards,
Kevin
My trinity won't work anymore...
Hi all!
My trinity wont't work anymore. When i press the ON/OFF-button, the display is lighten up a bit, then the buttons are lighten up. And nothing more.
When i will go to bootloader mode, it is the same.
And when i will to a hard reset, the trinity ask me to press SEND or END key for restore factory default or cancel. When i choose the SEND key, on my display some ridicoulous letters appear, but nothing more.
When i try KITL mode, everything is the same.
Can someone help please?
Because i can't do something on my trinity
EDIT (maybe this can help my helper ):
After some time, the display and the buttons are not lighten up anymore.
When i try to charging the battery, it only works, when the buttons are not lighten up (when i switch on, charging is ok; when the display is lighten up a bit, charging is ok; when the buttons are lighten up, charging won't work; when the display and the buttons are not lighten up anymore after a time, charging is ok)
hi... i have a similar problem.. i tried soft reset, hard reset, but my phone wont go past the boot screen.. previously i just updatet the windows mobile from 5 to 6 and the phone crashed half way throw.. can some one help me.. by the way the windows mobile was one update from the web...
never mind... problem solved... tks anyhow
weezer_88 said:
never mind... problem solved... tks anyhow
Click to expand...
Click to collapse
ok solved...
Can you tell how you did it?
Thanks
weezer_88 said:
hi... i have a similar problem.. i tried soft reset, hard reset, but my phone wont go past the boot screen.. previously i just updatet the windows mobile from 5 to 6 and the phone crashed half way throw.. can some one help me.. by the way the windows mobile was one update from the web...
Click to expand...
Click to collapse
But my trinity don't go to the boot screen, nothing on the display but lighten up slightly...
Nevertheless, can you please post, how you solved your problem?
THANK YOU in advance!
I downloaded the original Rom windows mobile 5 from http://www.htc.com/www/SupportDownload.aspx?p_id=3&cat=2&dl_id=111 then entered in KITL mode, connected the usb and reinstalled the original Rom, and all was fine...
Hello,
EDIT - Ok I'm just adding this bit to my post to summ up the whole situation from Post 1 until Post 14 in dot points
- HTC HD2, Began randomly freezing to "HTC" screen, when reset, loads "HTC" Screen and vibrates 5-6 times, sometimes let me goto OS, but at one point stopped letting me goto OS, Stuck at "HTC" Screen with the 5-6 Mysterious vibrations.
- I tried to flash a ROM off the HTC HK Website, 1.78 I think, Stuck at 9%, Those 6-7 Vibrations, tried again, same thing stuck at 9% with Vibrations.
- Tried another factory ROM from HTC HK the latest one, Flashed 100% the first time through, but then does not boot, just stuck at "HTC" Screen with vibrating
- Tried to flash same ROM again, begins vibrating and stuck at 9%
- I wanted to try if some custom ROMS worked, flashed HSPL 1.42 on, while flashing HSPL it finished on the device but on computer I got "Unknown Error
0x1003FF"
- Continued and went on to upgrade my HSPL to 2.08 so I can flash custom ROMS, now I have 2.08 HSPL.
- I tried Artemis Custom Rom for LEO, this one after it finished I think brang me past the "HTC" Screen, it actually said "quietly brilliant" for the first time, and to some Windows config screen where this Error appeared :
ARM11 FATAL ERROR
flash_os_wm.c line 339
- So I tried resetting, and stuck at "HTC" Screen, but No constant vibrating, only 1 vibrate.
- I tried Cheetah ROM, same problem, stuck at "HTC" Screen.
- I tried "NRG" ROM, same problem stuck at "HTC" Screen, well the NRG Screen.
- I tried Kumars ROM, same problem again. stuck at at the bootup screen.
I should mention whenever flashing, on the computer it never tells me what my current Image version is, it just tells me the one i'm flashing to. e.g the "FROM" field is blank. That's it until now.
Also everytime while at the bootup screen, it cycles e.g it will Vibrate, show bootup screen, do nothing, go black... then repeat the bootup screen, vibrate etc etc etc. After ROM is flashed, if I do a soft reset it will just stay at the bootup screen and not do anything at all.
Hard reset doesn't help either, neither does battery out/in, same thing just stuck at the intro screen with all the ROMS I try.
If anybody knows what the problem could be, please post.
ORIGINAL POST BELOW BEFORE EDIT :
-------------------------------------------------
Whenever I turn on my HTC HD2 It's stuck at the white screen with "HTC" in the middle, it will vibrate on and off about 4 times, and after that it will do nothing.
A soft reset with the Red button under the battery cover just brings it to the same screen with the same problem.
Taking the battery out and putting back in does not help, same problem.
doesn't even want to respond to hard reset (Vol down + Vol Up) + Power Button briefly.
When I try to put it into the Diagnostic mode (Vol down + Power), and try to flash a ROM onto it,
It just gives a Error 294, Invalid Vendor, maybe because I was using a ROM that was not Hong Kong, I don't know but I cant try flash again as the device does not respond to anything now (like before but can't even get into boot mode).
So I'm stuck at the moment and can't do anything.
Before this it would sometimes want to start up, and then get stuck sometimes, but now it's constantly not booting up
and begin stuck at the HTC Screen with 4 vibrates.
Sometimes it even boots upto the "HTC" Screen, and doesn't vibrate at all.
And at the moment I can't even get it into Diagnostic mode, doesn't respond to anything other than the reset button.
Any ideas?
Thanks.
EDIT ----- > Now goes into boot mode, I found out that QUICKLY after reset doing vol- and power gets it into boot mode. But while trying to flash the ROM, on my computer it says NOTHING about the current Image ROM on the PC, Trying to update now, this time it goes into a Progress bar on the HD2, stuck at 9%, and funnily enough at 9% it does the same (Vibrate 4 times) thing. and is stuck at the moment.
kidcash said:
Hello,
Whenever I turn on my HTC HD2 It's stuck at the white screen with "HTC" in the middle, it will vibrate on and off about 4 times, and after that it will do nothing.
doesn't even want to respond to hard reset (Vol down + Vol Up) + Power Button briefly.
.
Click to expand...
Click to collapse
Keep trying that hard reset method. Make sure both buttons are fully pressed and briefly press power button to get HSPL to appear.
Follow this guide:
Performing a factory reset using phone buttons
1. With your phone powered off, press and hold the VOLUME UP and VOLUME DOWN buttons.
2. While holding the volume buttons, press the END/POWER button briefly and then release it.
3. When you see a warning message on screen, release the VOLUME UP and VOLUME DOWN buttons.
4. Press the VOLUME UP button to perform the reset, or press any other button to cancel the reset.
Thanks for the reply,
Sorry I was editting my post while you were replying, please read it again it has some updates on what is happening at the moment.
Got it to go into boot mode, SPL 3.03 Version, connected to USB, tried to update with HK ROM, stuck at 9% and does 4 x Vibrate, now stuck at 9% on phone and computer.
What should I do now?
Update - Error 262 on Computer (UPDATE ERROR) the ROM utility has encountered a communications errors during the update process
The computer guided me what to do :
1. Remove USB cable
2. Battery out, battery back in.
3. Start device up and flash again.
Device started at "Software update failed", i was able to plug the usb cable back in, and start flashing again.
at 4%, It vibrated 4-7 times while going from 4% to 9%, and progress stopped at 9% Again.
That vibrating I don't know why it's happening.
I even tried updating again, and it does the same thing, vibrates 4-7 times and then stops at 9% update.
Is the ROM I'm using a bad one? It's the HTC Hong Kong one from early 2010,
There is another one I can download which is from Late 2010, but it's SPL Version might be too high.
The reason I'm trying to update a ROM is to get an early SPL, so I can load HardSPL to use Custom Firmware.
EDIT -
Edit - I just tried Hard Reset, but it just goes to the "Software Update failed, please try again" screen. Tried to load ROM on again but still the same vibrating and stuck at 9% during update.
Hi,
Now I tried updating to a later HK ROM, and it updated but still now has the Green HTC Screen with the vibrating. The ROM that did the Vibrating during 3-9% and stuck at 9% was :
HTC HD2 RUU_Leo_HKCSL_WWE_1.72.831.1_Radio_CRC_Signed_15.32.50.07U_2.07.51.22_2_Ship.exe
And the one that Is Updating without problems and works fine is the newer one found on the HTC HK website :
HTC HD2 RUU_Leo_HKCSL_WWE_3.14.832.3_Radio_15.42.50.11U_2.15.50.14_LEO_S_Ship
This one it lets me update all the way through, once it's complete the device goes black and does not respond to anything, Battery out and battery in and the device starts up, but goes to the HTC Screen, and then Vibrates 5 Times.
And then does not respond.
What is the problem??
Even tried a Hard Reset, and again it does the same thing.
Boots, Vibrates once on HTC Screen, 5 seconds later, it vibrates on/off about 7 times and that's it, stuck at HTC Screen.
Since those 2 ROMS don't work, is there any ROM or Software that I can try to put on that will let me somehow get my HD2 Working again.
I had the same problem. I fixed it by flashing radio version 2.15 and then re-flashing hardspl. Then i installed a custom winmo rom. After that my phone was fine.
Sent from my HTC HD2 using XDA App
UPDATE !!
Ok this is getting very weird.
So I tried to flash the Later ROM that ORIGINALLY WENT ALL THE WAY THROUGH 100%.
THIS TIME, IT GETS STUCK AT 8%, and then the phone Vibrates 5 times just like the earlier ROM.
Does anybody know what this vibrating is indicating? I might try to ask HTC, but even though they developed the phone they would probably be of no help since they sent me a faulty phone back from Warranty.
kidcash said:
UPDATE !!
Ok this is getting very weird.
So I tried to flash the Later ROM that ORIGINALLY WENT ALL THE WAY THROUGH 100%.
THIS TIME, IT GETS STUCK AT 8%, and then the phone Vibrates 5 times just like the earlier ROM.
Does anybody know what this vibrating is indicating? I might try to ask HTC, but even though they developed the phone they would probably be of no help since they sent me a faulty phone back from Warranty.
Click to expand...
Click to collapse
Just info, I read that some users reported the same as you. And unfortunately, they have to bring it to HTC repair as this might relate to hardware malfunction.
If you are under warranty, you better bring it for repair.
Cheers
silverwind said:
Just info, I read that some users reported the same as you. And unfortunately, they have to bring it to HTC repair as this might relate to hardware malfunction.
If you are under warranty, you better bring it for repair.
Cheers
Click to expand...
Click to collapse
+1 for this. Most recently, there have been some users reporting multiple vibration patterns (usually 7 times) when turning on the phone. None of them was able to flash any ROM to bring back their HD2.
At least, most of them were able to install an original SPL before sending it to a service center. However, I never read anything about the final outcome.
The phone has already been through warranty once, and HTC's slack attitude and approach offended me greatly. They wrote on the paper "No Faults Found", which shows their reluctance towards fixing their faulty phones that they are bringing out to us. They just reflashed a ROM with appeared to "fix" the original voice problem I was having, but I didn't have enough time to test the phone out before it began malfunctioning and vibrating on startup when they send it back to me.
And the fee's and costs to get it to Hong Kong are just not worth it, having to pay the postage back from Hong Kong, plus to receive my HTC in worse condition than it was before I sent it to them.
HTC isn't what it used to be
Hi,
So i tried flashing to an older ROM I was shown to by users on the HTC HD2 forum,
It was 1.48, and It flashed all the way through, so then it didn't let me soft reset after the flash I think, so i took the battery out and put it back in.
After that It didn't do the vibrating, only vibrated once at the HTC Screen but was stuck at that.
Now though I am at SPL 1.42, so any point in trying to put HardSPL on and going to a Custom ROM? I just haven't been able to get any ROM to boot up yet past the HTC Screen.
Trying to reflash with the same ROM again this time it's stuck at 0% All the time.
So i tried updating to HardSPL, It got past the "We hacked it" Screen, but after that when it went to the Progress bar on the HTC HD2, on my computer I got the Error :
Unknown Error
0x1003FF
However now when I go into boot mode, It shows that I have HSPL Installted.
Now that I have HSPL, any tricks or Firmware I can flash to try fix these problems and try get a ROM working/booting?
I'm using Windows 7.
Another update - I put HSPL 2.08 on so I can flash Custom ROMS (well most of them i guess).
So i got Cheetah's ROM, I flashed it on and then after it was on, the HTC SCreen appeard, and then the ROM Version in Red letters at the bottom, but it did not boot up, so I did a reset, and then the HTC Screen comes up and is stuck at it.
UPDATE -- Did battery out / battery in, and It GOT PAST THE HTC SCreen, it displayed the "quietly brilliant" text, then it got into a windows screen, but then the Error
ARM11 FATAL ERROR
flash_os_wm.c line 339
I can't click "OK" on the window either its frozen.
A soft reset brings it to the "HTC" Screen with no more.
Battery out / in brings it to the Same "HTC" Screen but then it turns black for a sec, flashes,
then back to the "HTC" Screen, with no Red letters at the bottom, and it keeps going black,
then vibrate and back to HTC Screen continuously.
Sometimes though it will just be stuck at the "HTC" Screen with no Vibrating, just that screen.
I just tried flashing with the "NRG" ROM, I can't get past the "NRG" bootup screen now, soft reset or battery in/out does not help.
So far have tried 4 different custom ROMS, All give the same problem, stuck at the intro screen after the flash.
Also the installer on the computer doesn't say what my current Image is.
Any help greatly appreciated.
hello,
please try the following.
On the back of your phone, the battery cover (metalic) comes over 2 small metal pins. The phone will detect if these 2 pins make an electric contact, aka if the backplate is mounted. Some HTC have either microcontracts or magnetic sensors to prevent a phone to be flashed or to boot with the battery cover missing or improperly attached. This is because without the cover, there is a greater risk to have the battery disconnected or to fall, thus interrupting a reflash process.
Older HTC's would either prevent a bootup in case of missing cover or simply didn't start-up at all. I don't know what's with hd2 but i had one of them with exactly the same problem, and knowing that i checked those small metalic pins. One of them wasn't making a proper contact with the metalic cover, after i fixed that the phone was able to corecty flash a stock rom from the microsd card.
However, i repeat, i don't know if this is really the case with HD2, i may have just been lucky. One more thing, if in the end the phone woun't recover from this, i suspect a nand memory corruption. Kind of like bad sectors on a hard drive. Back some time ago, i only manage to fix a broken device with this problem after doing some welding on the cpu and connecting the board with a pc via jtag interface. Then i could mark the bad sectors as "unavailable" and correctly flash a bootloader.
Sorry for the english as i live in a non english speaking country.
LE. nevermind that, did a hardware check with some equipment, the battery cover issue is not the case with HD2. The problem seems thermal related, - if you cool the phone to 5-6 degrees celsius, the problem should either dissapear or occur less frequently. I suspect the CPU soldering to be crappy in this model, so when the chip heats up the small solder balls (the chip is BGA mounted) either don't make a proper contact due to dilatation in the chip itself or the solder materrial. Aah, i really don't know how to put it in english. However i still have a hd2 with this problem. It's worth disasembling it and trying some fancy soldering with a smd rework station.
HD2 vibrations
By me it was HARDWARE problem.
Try to give phone to 5 celsius for few minutes. After try to flash.
By it works, but after doesn't want to power on.
Hey people, I usually upgrade roms on my blackstone, been 2 years now, all fine, until yesterday after a task 29.{Ypsmav rom} My phone didn't want to start, eternal freeze on start up with the htc logo ..
Can you kindly help me please.Tried several HR, to no avail..
This happend to me, this is what i did to fix it:
Take the batery of the phone
Wait a few minutes and put the batery back on
With the USB Cable unplugged press the Volume Down button and then the Power Button
Plug the USB into the phone (Don't do anything else to the phone)
Run the ROM you downloaded
Select Task 28 and upgrade.
It worked with my Touch HD
task 29 completely formats your phone, including the rom partition, so of course it cannot boot into windows mobile, there is currently no windows mobile on it!
as already pointed out, you need to flash a rom again.
Hm, Got it resolved . Thxs anyway
Hey guys!
I hope it´s ok to use this thread for my question...
I have a big problem with my old Blackstone... I didn´t use it for a long time (because I got a HTC Desire and a Galaxy Tab). Now i started the phone, but it won´t boot. It stucks at the boot screen (HTC Smart Mobility)...
So far so good... So I thought, I´ll do a Hard Reset... Then I saw that the VOL-Buttons are broken... So, HardReset with VOL-Button won´t work.
Is it possible to flash the phone via USB (ActiveSync doesn´t work...)?
Or is the phone broken?
Thanks in advance for help!
Cya
without the use of the volume buttons, it is next to impossible to get the device working again, since your device does not boot into winmo nor can you access the bootloader mode to flash it. your only chance would be to get the volume keys working again, have you tried using them without the back cover and pressing them really deep?
Hey.
Yeah, I've tried to get the Buttons work again, but keys are definitly broken. Something seems to miss on the buttons, so I think the are broken...
Sent from my GT-P1000 using XDA App
since you do have another phone, you might want to consider giving away/ selling your blackstone.
lately, i think there are more and more threads with people that have problems with their displays and/or digitizers and they might be willing to buy it for parts or you could donate it to the developers of xdandroid, so they finally have a device to test it on.
or you could search and download the htc blackstone service manual pdf and disassemble the device yourself to fix the buttons.
Blackstone freeze on startup after task 29
frsb said:
this happend to me, this is what i did to fix it:
Take the batery of the phone
wait a few minutes and put the batery back on
with the usb cable unplugged press the volume down button and then the power button
plug the usb into the phone (don't do anything else to the phone)
run the rom you downloaded
select task 28 and upgrade.
It worked with my touch hd
Click to expand...
Click to collapse
it worked for me too bundle of thanks