The battery came out will the device was connected to the computer via usb. Don't ask how I was messing about, the back came off and then the battery fell out. Now I can't turn it on. When I plug into the mains adaptor the charge light does come on. Any ideas.
Thanks
try to set the device in BOOTMANAGER mode and see if you at least can access that part of the phone!
What did you do when the battery 'came off'? Flashing it?
If you did not flash it press and hold the power button and remove the battery. Keep pressing the power button for an additional 15 to 30 sec after you removed the battery.
Leave the phone without the battery for half an hour or so, then press and hold Power for 30 sec. While still holding the power button place the battery back in, release power, wait 10 sec and try to turn it on ...
Thanks very much for your reply. I had just flashed it. It had rebooted and hung on the splash screen. I then picked up the phone and accidently knocked the battery out. Do you think this makes a difference to your suggestion?
Tried your technique but nothing unfortunately. It may be dead!
Thanks anyway.
Maybe my phone is dead too
I did the same with my phone...just did a flash and rebooted and now freeze on the splash screen...what can i do to save my phone?
If you're phone still turns on and just hangs at the splash screen as far as I understand you can then hold down the camera button and press the soft reset key. This should take you into the bootloader. From there you can re-flash the device with a different ROM like 'Wizard Love' (you can find it on this site somewhere, use search) or download the latest ROM from your provider. Use a NO_ID flash utility which means you don't have to have Activesync 'active'. My problem is slightly different as my device won't turn on at all. I've just bought a replacement battery just incase thats the problem. Otherwise I guess its gone for good.
If the flash finished successfully you can try first:
HOLD CON KEY (left side of the phone) + VOICE DIAL KEY (right side of the phone) + RESET. This will HARD RESET your device and re-initialize the ROM - might be that that can fix it! If not try to reflash it with the shipped ROM
BOOTLOADER MODE:
Power button + Camera button + Reset.
Junner2003 said:
If the flash finished successfully you can try first:
HOLD CON KEY (left side of the phone) + VOICE DIAL KEY (right side of the phone) + RESET. This will HARD RESET your device and re-initialize the ROM - might be that that can fix it! If not try to reflash it with the shipped ROM
BOOTLOADER MODE:
Power button + Camera button + Reset.
Click to expand...
Click to collapse
Thanks for the bootloader info....I had totally messed up my 8125 earlier...and now its back!!
THANK YOU!!!!!!!!!!!
Related
I having a problem with my Hermes, i am running WM6.1 CRC13.3 and my Power button simply refuses to work, i simply does nothing when i press it, i thought it could be a hardware problem, but if i turn off hermes(by taking the battery out, since the power button doesn't work) and put the battery back, it instantly turns on itself on without pressing power button... When the phone is in stand-by mode, i have to press the button next to the Power to wake it... the power button simply does nothing... However then i take the battery out, and press Power+OK and put the battery back, it goes to the booloader screen, so the Power button physically appears to work.... I haven't tried to hard reset it yet...
does this happen with other roms to?
i does not reflash you device with an original rom then flash you current rom, this kind of weird bugs appear when flashing wm6+++ roms.
mine used to self reset when i soft reseted.
No, i flashed this rom a couple of months ago and never experienced this issue...till now..
Mulder3 said:
No, i flashed this rom a couple of months ago and never experienced this issue...till now..
Click to expand...
Click to collapse
similar to my then.nevertheless , do what i posted above ,at the same time you can check if the power button works with the original rom.
Hi, I am having an issue getting my X2 into boot mode in order to update the firmware - even following the instructions on SE Update Service (press and hold volume down button and power button until white screen appears)
All that happens is the vibration feedback to indicate power on, then the phone loads up as normal.
I've updated another X2 and it worked correctly, the problem appears to be with this specific unit.
Does anyone have any suggestions on what may be causing this, or how to get this one into boot mode please?
Best to send it to service centre..
could it be because it's made in china? just a thought...
Just note that on the X2 you wont see the bootloader.
You know your in the bootloader when the phone stand on the SE Logo.
Then you can connect the phone and update it
Hi, thanks for the advice all
I can't send it to a service centre as I don't have a receipt unfortunately
I'm not sure what being built in China has to do with it not entering boot mode, most SE phones are and I've not had a problem with my other ones?
Thanks for the advice on boot mode - I successfully used SEUS an another X2 and the boot mode is essentially a white screen with the SE brand logo - sadly I don't get that white screen just the black screen with logo and vibration feedback then it powers on.
Any other suggestions or should I give up and sell as faulty/parts only?
Thanks
nonentity said:
could it be because it's made in china? just a thought...
Click to expand...
Click to collapse
And the X1 was made in Taiwan. What's your point?
bootloader phone stand on the SE Logo
hm, obviously missed that one after X2 subfora where created...
Mod. edit: moved to correct forum, X2 General
try this:
read all steps first
turn off phone
pull out battery wait ten seconds
put battery back in (leave cover off)
hold the power button + hold volume down
press the soft restart button* (while still holding the power button + volume down)
keep buttons held down till you see the white screen and green logo.
note* push the button with stylus it is hidden under where the stylus goes in next to the camera.
plug into the computer and run SUES it'll say already have latest version update anyways? click yes
i had to do this when i bricked my phone, (my computer crashed while i was doing the update) it really saved my day.
x2 dead
I have same problem in my phone , during update with SEUS computer hang and now
my phone shows only vibrate.
i have tried volume down+power+reset
but it can't go to white screen or sonyericsson logo.
any other solution
harveydent said:
And the X1 was made in Taiwan. What's your point?
Click to expand...
Click to collapse
his point is if this Xperia is the one that's fake.. the one from China..
10X
yummy-fun said:
try this:
read all steps first
turn off phone
pull out battery wait ten seconds
put battery back in (leave cover off)
hold the power button + hold volume down
press the soft restart button* (while still holding the power button + volume down)
keep buttons held down till you see the white screen and green logo.
note* push the button with stylus it is hidden under where the stylus goes in next to the camera.
plug into the computer and run SUES it'll say already have latest version update anyways? click yes
i had to do this when i bricked my phone, (my computer crashed while i was doing the update) it really saved my day.
Click to expand...
Click to collapse
10x dude. u saved my x1
extracted rar archive directly in task29 folder, dono how, but didnt replace the ruu_sign.. and flashed whit the 3MB ruu file in the folder..
i found your post 1st, and managed to boot and install from sd.. many 10x
Just bought my Advent Vega today and was all running fine. Charged it too 100% then turned off and booted into the stock recovery. I then waited for it to show up on the computer as i have already got the drivers installed as i have jjust today flashed someone elses vega on the computer. mine didnt show up and then unplugged it and now it wont turn on at all. Tried charging it and then try booting. Unplug charger nothing. The thing is that the charging light still shows.
Any Help would be great. Dont want to have to send it back for repair. it may take weeks.
Thanks
Alex
Hmmm.... it could be a faulty unit, but my guess would be that you need to try at least 10x to try to turn it on.
I know some people complained that the buttons are very poorly designed and sometimes don't even work.
It's the same for my tablet, the "power/home" button doesn't always work like it should.
Once, I had to retry five times in order to power on the device.
If it's not that it could be some other minor issue, try holding the power button for a long time (8 sec), or try to go into recovery again, or something like that.
a sighn its trying to boot is the blue led under the camera tilt the vega away from you and look at the edge of the LCD it will glow when powering on
have you tried push back button, hold it, then press power button 2 second, the release the power button while still pressing the back button? it should be recognized and can be flashed
pramanta said:
have you tried push back button, hold it, then press power button 2 second, the release the power button while still pressing the back button? it should be recognized and can be flashed
Click to expand...
Click to collapse
Some times this can take several attempts.. and i mean several!
I actually had Audi running and had it connected to the pc so could tell if it had worked or not... not the correct way i know but it worked for me.
Interested to know if you ever got this sorted alcurtis93? I'm having the same issue with a vega where it won't even bring up the backlight. No life in it whatsoever.
A bit of a late reply, but try to wipe your device and maybe even flash a newer custom rom
Hi All,
I need your quick help, I dont know why but I cannot start my Samsung focus v1.3.
I tried to flash it by pressing power button + volume down + camera button but can't do hard reset.
When I am trying to remove battery and reattach battery again, then phone just showing "SAMSUNG" screen and again goes switched off.
Even I tried to press power button + volume UP + camera button then it shows only "Download Mode" screen only nothing happens after this.
Please need your help!
Many thanks in advance,
Since you just flashed it, I assume that it started up by displaying 'SAMSUNG" and seems to be stuck there.
If that is the case, you need to be patient. It takes a few minutes to get past that point. Every time I flash, I feel like I have done something wrong and the phone is bricked. But it always moves past that point after a few minutes.
wildbilll said:
Since you just flashed it, I assume that it started up by displaying 'SAMSUNG" and seems to be stuck there.
If that is the case, you need to be patient. It takes a few minutes to get past that point. Every time I flash, I feel like I have done something wrong and the phone is bricked. But it always moves past that point after a few minutes.
Click to expand...
Click to collapse
Thanks for your reply,
But I haven't flashed my phone..
and from yesterday it is showing same 'SAMSUNG' name screen and then again goes switched off..
dont know what is going wrong.. or is it due to battery issue?
please help!
nah, it's the power button switch which somehow got stuck, it's a relatively common issue with the focus it seems
some people have reported that cleaning the button helps, others simply have replaced the whole switch at a local repair center... do what you think is best
Saiyaku said:
nah, it's the power button switch which somehow got stuck, it's a relatively common issue with the focus it seems
some people have reported that cleaning the button helps, others simply have replaced the whole switch at a local repair center... do what you think is best
Click to expand...
Click to collapse
Thanks Saiyaku,
But how power button works when I press (Powerbutton + Volume UP + Camera button), screen shows me "Download Mode" nothing happens after that. Yesterday whole I tried these options..
help
To flash magldr, you need that combo , press power button + volume UP + camera button then it shows only "Download Mode". To flash a ROM, you go Vol DOWN, and then reset your phone, or format, and then go back to the same menu, and when you see the do you want to format your phone stuff, you hit the back button and you'll see the magldr screen where you'll connect your USB and go forward with the flashing process. Perhaps try flashing an actual ROM to your phone. You can't really do squat from from the download screen but add magldr really. Hope that helps you.
Please need your help!
DACHEF81 said:
To flash magldr, you need that combo , press power button + volume UP + camera button then it shows only "Download Mode". To flash a ROM, you go Vol DOWN, and then reset your phone, or format, and then go back to the same menu, and when you see the do you want to format your phone stuff, you hit the back button and you'll see the magldr screen where you'll connect your USB and go forward with the flashing process. Perhaps try flashing an actual ROM to your phone. You can't really do squat from from the download screen but add magldr really. Hope that helps you.
Please need your help!
Click to expand...
Click to collapse
Thank you for your comment, but I haven't installed magldr.
[email protected] said:
But how power button works when I press (Powerbutton + Volume UP + Camera button), screen shows me "Download Mode" nothing happens after that.
Click to expand...
Click to collapse
because download mode disables the power switch (it even says "do not turn off"), that's why it seems to "work". power switch is active at the format prompt, however, so when you enter that mode the phone turns off immediately afterwards
do a little experiment: remove the battery, then put it on again while you're pressing volume down plus camera... you'll probably see a little surprise there
it's the switch. go repair that nao
i have the same problem, and many unfortunate people out there , but my phone on service center now, and i just wanna tell you about this thread this http://forum.xda-developers.com/showthread.php?t=2007946, maybe can make you calm for a while... look at his problem solution
Hi every one,
I come to you because i dont find a way to get in to my oneplus 6t.
My oneplus is Unlocked since last year so everything was fine until yesterday when i ran out of battery, and when i tried to torn it on it didnt wanted to.
It show this on the screen:
----------------------------------------------------------------------------------------------
<!>
The boot loader is unlocked and software integrity cannot be guaranteed.
Any data stored on the device may be available to attackers.
Do not store any sensitibe data on the device.
visite this link on another device:
g.co/ABH
PRESS POWER KEY TO PAUSE BOOT
--------------------------------------------------------------------------------------------
I have tried to press power + up botton for 7 seconds and it start again in the same screen.
I also have tried to press power + down botton and nothing happen.
And also the power botton alone but nothing.
Does any one have any idea of what to do?
Thanks and sorry for my english.
You need to unlock the device bootloader or restore the software using the msmdownload tool.
You need to hold the power button longer. Be patient it will boot.
bladestonez said:
You need to hold the power button longer. Be patient it will boot.
Click to expand...
Click to collapse
Yes what he said. First plug it in for a few minutes to get it charged and then hold power button +vol up for at least 20 to 30 seconds. It will turn on you just have to hold button longer