Hello,
yesterday i was doing the hardspl thingy
it was complete but then the RUU thing gave
ma an error 276 (or 267 cant remember).
so i followed the steps for revocery .. it told
me to unplug the usb . put off the phone and then
put it on again the prob is i cant put it on again ..
when i hold power butten folr 3 seconds or longer
it doesnt do anything..
could anyone help me ?
thanks in advance !
Related
Hey Guyz ..
i need help here ma phone is totally dead nuthing repond in it
i tried 2 setup an old WM5 source & after da installation finished ma ppc was dead & nuthing in it respond & it dont want 2 open
sooo if any1 can help i'll be pleased :X
try this
hi
i briked my phone a few days bak ie phone totally dead no screen action if this is ur problem try this
switch phone off take battery out hold power buttom for a few mins then put batt back holD camera button and then power on u will get tricolor screen use usb and flash new ROM or hold camera and do soft rest with stylus this will also give u try color boot screen ( also see my thread at gene upgrading it says hone dead )
goodluck
dallos said:
Hey Guyz ..
i need help here ma phone is totally dead nuthing repond in it
i tried 2 setup an old WM5 source & after da installation finished ma ppc was dead & nuthing in it respond & it dont want 2 open
sooo if any1 can help i'll be pleased :X
Click to expand...
Click to collapse
still nuthing happens ??? if u can tell me wht i should do in steps
1. Remove battery
2. Press and hold the power button for 5 seconds.
3. Replace battery
4. Press and hold the camera button & power button.
5. Poke "reset" with the stylus, you will get the tri color screen.
BTW flashing WM 5 was a bad idea . The gurus have suggested against it repeatedly.
u flashed ur SPL
what i knw from this is that u have flashed ur SPL using the WM5 ROM...try ti get tricolor screen as explained by Haree and see what SPL is showing on the screen....
after that we can see which ROM is suitable for u or how to flash new SPL on ur phone....
From the serial number it can be guessed (nor confirm) that ur is new gene...so read sticky's post of unbricking....
tell me wheher ur gene came with windows 6 preloaded?
the problem is i tried all this but i dont get to the boot screen
nuthing happened when i do this ... some ppl told me 2 try the JTAG method but i dunno how 2 do it ??
if Any1 could explain 2 me how 2 do the JTAG Method it'll be gr8 ....
ma mail is [email protected] ...
thx for ur help in advance
dear all experts ...
I tried to update my Shadow by the new wm6.1 rom.. the first time it went to 100% and restart with an error 270 : the image is corrupt . After, when I boot loader, it go to 2% and restart every time ( many) :
I'm stucked at bootloader mode and tried many roms but no one sucsess ... all of them reach 2% and then stopped.
even I tried the original one (Shadow_Software_Update_1.11.531.5.exe) from t-mobile official site but also same result.
so can any one help me and give me any solution to try?
try to install this on your phone
http://forum.xda-developers.com/showthread.php?t=394478
after that try installing a cooked ROM
Dear sir;
thanks a lot for attention to my problem and ur kind reply.
I already tried to do this but...
* How can I upload sspl/uspl to my phone from bootloader because it's the only mode I can work my phone?
* when I tried to do USPL + RUU it go to 100% and then the phone restart and the RUU program says corrupted image...
then the phone stays in it's state (only can go to bootloader mode).
can I use MTTY program to flash sspl/uspl and USPL and then the new rom? if yes .. how I can do it?
Or what may I do my friend..
thnx a lot again
if you can only get to the bootloader then try flashing to the t mobile rom, then start over
Mee toooooo
I installed this ROM and it doesn't work!!
the screen is freeze with the Windows 6.5 Logo, and thats it!!!!
what can i do for do a hard reset?????? (i already do that thing, power it on, and then push the 2 soft buttons, and didn't work!),
HEEEEEEEEEEEEEELP!!!!
isfected said:
I installed this ROM and it doesn't work!!
the screen is freeze with the Windows 6.5 Logo, and thats it!!!!
what can i do for do a hard reset?????? (i already do that thing, power it on, and then push the 2 soft buttons, and didn't work!),
HEEEEEEEEEEEEEELP!!!!
Click to expand...
Click to collapse
Power off the phone
Press and hold the camera and voice keys
Insert the USB cable, Keep holding the camera and voice keys until you get the bootloader screen
Then flash an original ROM.
I flashed a ROM (HTC_TyTN_WWE_3.54.255.3_6275_1.48.00.10_108 aka Official WM 6.0) and now when i want to put back the original ROM (RUU_Hermes_QTEK_WWE_2.11.255.1_102_6275_1.38.00.10_108_Ship) i cant do it because the RRU is remaining blocked at 13% and now i cant do anything because every time i power on the phone, it goes in bootloader i think .... any help ?
I tried recovery mode, 3 sec battery removed and then soft reset but i still get ERROR 262.....
Can anyone help me?
sorry for my bad english!
Hi to all ,
I have the msn account:[email protected] .Once again,just to make the resume of the whole story if I remember well:The trinity was with the initial sfr 300+ software(wm5);I installed the oli1.20 flashed it with some other ROM software,did not like it and returned to the original one.Then I tried to flash it with the ROM software where all went wrong...After 1 % the screen went blank and all I can do with the device is to put it into the boot-loader mode where it says:
TRIN100
IPL-0.50
TRIN100
SPL-1.07.0000
When I extracted the file,I discovered that it has 2 nbh-files.I think that is the reason of my defete.Afterwords I have tried all sorts of the first aid solutions : splxploit-windows cannot connect to the device;it says that there is no WCEUS-file and therefore it cannot continue.I have tried to re-flash it through the sd-card:I re-formatted the card on fat32,without any name,put the original ROM and tried to let it boot that way.No success,it marks:loading ... and after 3-4 secs it returns into the boot-loader mode with the same message mentioned above ...
Salutations frm Luxembourg , Goran Stevanovic.
Thx all of ya , problem solved.
sir me too have same probelems, but ma 2 htc trinity dnt stuck at bootloaders, its to to operator logo and stuck there, i have 2 phones with this probelem.
please help me to solve this probelem sir.
gurnek said:
sir me too have same probelems, but ma 2 htc trinity dnt stuck at bootloaders, its to to operator logo and stuck there, i have 2 phones with this probelem.
please help me to solve this probelem sir.
Click to expand...
Click to collapse
1: Boot into BL (camera + power + reset hole)
2: Download the GPS enabled ROM from HTC Support, NOT from a rapidshare/megaupload/4shared etc.. mirror.
3. Flash the ROM, but use the hardspl flasher.(For some reason, it doesn't go error 270 if I use this flasher).
4. Hard Reset again.
Hello,
I have a HTC P3600 and after i make a hard reset the screen goes all black, i already try flash the phone but don't result.
If i try to make a hard reset again the screen shows "press ok to make hard reset" after that goes black again.and its completing %100 but when i want restart its still doesnt work just black screen. just working light =(
So i think not display problem.
Any solution? help me plss
Any chance of sharing the solution, guys, my SPV M700 has similar problems. I tried to flash it with the TRIN-SSPL rom, but it kept saying I need a newer version of the update software.
Now all I have is it gets stuck on the green Windows load up screen and when I reset (Camera-PWR Button-Reset) it goes onto the bootloader tri-color screen, similar to what Goranchen had on his. What do I do now, I would really like to use the phone on another network, and I have looked after it really well, I think, so would be a shame to throw it away. Please help!!
Hi ,
I was flashing my jasjam using sspl-herm and a 6.1 rom ,
While upgrading the progress bar reached the end but it stayed saying upgrade in progress , it took too longer than normal and i knew it wouldnt continue so i soft resetted the phone ,
now it's stuck in the splash screen before even the windows loading.
Plz plz plz help....
if you can access bootloader
a) if you dont have hardspl installed already, install it or you're going to be screwed soon.
if you can access bootloader, pop the nbf file onto your microsd <2gb as HERMIMG.NBH insert it into the phone and follow onscreen instructions.
flashing via SD is always a safer bet anyway.
Hey ,
Thnx guys 4 help
1st I tried hard resetting and it didnt work
2nd I DONT have hard spl
3rd I get into bootloader , i plug the usb cable but i cant flash , the ruuwrapper program says error during upgrade , i think it cant access the phone first coz the mobile device icon in my computer is emtpy , second activesync says not connected(although it tries to) and device manager reads an " htc usb sync " drive but no letter or something
Still no luck , any help ??
I think I've got same problem..
It can't run again after splash screen..