HEy guys! I have a small problem. I have a Kingston 1 GB microSD with miniSD adapter and I wanted to use it with my Wizard, but it's not working! (On my PC it works) Please help! I've tried several ROMs (thought that it's the failure of the software), but no effect. Maybe the device's slot turned dead?
you should first check if it accepts a regular MiniSD card and see. i heard about adapter compatibility issues so it might be that.. but again, check if it works with Regular miniSD... if it doesn't, it's probably a problem with your device. try a shortcircuit between the leg on the far left and the one before far right one.. (after putting it in your adapter)..
Thank you for your fast reply! I will do as you adviced and write when I got any news.
no prob.. just make sure you don't burn your card.. hope it helps.
Related
Hi.
I have tried to make two different WiFi SDIO cards work in my Qtek S100 now with no success despite following all advice on these forums and trying many different drivers etc.
My suspicion is that my S100 has a hardware fault and cannot read from the SDIO slot (although MMC cards work fine).
Does anyone know whether there is a way of checking this hypothesis?
Cheers,
Tom
Solved it!
The extra pin that SDIO uses had got pushed down. Use of cocktail stick to bend it back again solved the problem...
The answer to "is there an SDIO test" is yes - insert the card when the device is on standby. If the screen lights up, it's seeing the card.
Tom
Hmm... I sort of have the same problem. I got my new Wifi card today (PocketGear, or Spected mini card) and used it for 10 minutes. I took it out to replace my SD card, the screen lit up but nothing is recognising. Storage card doesn't appear and phone things nothing's connected when the Wifi card is in. Not good!
I'll check the pins when I get home, but since the screen is lighting up I'm not sure about that,
Any ideas, people?
Ok, well it seems it's fixed. 3 hard resets in 10 minutes fixed the issue! Good ole Microsoft, making nice and sturdy operating systems!
hello guys & gals, i bought a sandisk 1gb minisd for my wizard this morning, however whenever i put the card in the phone doesnt seem to read it.. any ideas on what one is ment to do? thanks in advanced!
Hi - you did not say which wizard or which rom. Occ they are a bit fussy with the minisd card but if you put it in and out a few times that may do it, check contacts are clean and no fluff in the slot! Check the disk on the pc to see if it will read it and all is well. Some people have had success formatting disk on pc to fat32. If all else fails its a dud and go and get a new one
Call me unlucky but after having had 3 repaired (reconditioned) vario 2 PDA's from T Mobile within 4 weeks, which all overheated, they finally gave me a brand new Vario 2 from the shop floor.
Problem is, when I insterted my brand new Micro SD 1Gb sandisk storage card, its not recognised. Also, I notice that when its been inserted for 10 mins, the little metal hook hole on the device (where you attach can a strap) got VERY hot, as well as the area around the storage card got hotter. I have tried a friend SD card and that too does not work. I have also tried soft resetting device with card in/out but no joy.
Has anyone heard of this before? and is there a fix so that it recognises it? Also, why the overheating?
Thanks
Al
Edinburgh
Forgot to say, my device info is;
ROM Version: 1.21.110.3
ROM date: 06/19/06
Radio version: 1.05.05.00
Protocol version: 32.36.7010.04H
WM5
One suggestion: exchange another MicroSD card.
Nghiem said:
One suggestion: exchange another MicroSD card.
Click to expand...
Click to collapse
Also worth trying to reformat the SD card with a PC. Some folks find too that they have to be very careful in inserting the card to make sure it is seated correctly.
Mike
Thanks gents. Well Ive reformated it with a PC and I already know the card works fine in other devices/PC so its not faulty.
Has anyone heard of this happening?
qbaser said:
Thanks gents. Well Ive reformated it with a PC and I already know the card works fine in other devices/PC so its not faulty.
Has anyone heard of this happening?
Click to expand...
Click to collapse
Other folk have had problems. I have seen debate about whether some brands eg Sandisk are not good etc. I use a Sandisk without problems but others do. There has been discussion in this forum - perhaps try the google search sticky post.
Mike
Also, when the card is inserted, as well as the heat increasing in the device, the battery runs down at 5 times the normal rate. It just lost 20% in the last hour....sitting doing nothing.
Hi guys!
I've read several threads here regarding which cards work and don't work in our machines. One of the main threads is ridiculously long, and describes various reg hacks that do NOT solve the problem.
In my opinion, there is NOTHING worse than a PDA that needs to be rebooted every day or several times a day.
I am starting this thread just to bring the basic information into one place.
I can tell you right now:
I have two 2GB Sandisk MicroSD cards, and one 512MB card.
Not surprisingly, all three have problems in two 8525 devices, with two different WM5 ROM.
I know that the 1GB Made in Japan Kingston seems to work flawlessly.
Can anyone else please share their experiences in this thread? Let's keep it nice and clean, so that people wanting to understand what works and what doesn't.
How are the 2GB Kingston cards? Anyone have any luck?
I have used the SanDisk 2GB with no known issues.
I also have a 2g Sandisk with no issues over nearly 11 months.
I'm not sure you will prove much here as I have seen folks who swear Sandisks are bad and Kingstons (typically 2gig) are flawless. Equally I have seen exactly the reverse views reported. It may have more to do with physical connections (contacts) between device and the card.
But lets see how it pans out.
Mike
bkeenan said:
I have used the SanDisk 2GB with no known issues.
Click to expand...
Click to collapse
I have as well and love it. Only issue I have is getting the little sucker out! I just leave it in. The only way I have found to get it out is by opening the back, and using an eye glasses screw driver to slide it out.
sandisk 2g and 1 g here and no issues with either work perfect. um you do know if you push it in it releases the catch and it pops out like its suppose to right?
austinsnyc said:
sandisk 2g and 1 g here and no issues with either work perfect. um you do know if you push it in it releases the catch and it pops out like its suppose to right?
Click to expand...
Click to collapse
If only it was that easy. For some reason, mine doesn't do that. I push in, it doesn't pop out
Not AKU2.3?
Hands up those of you who have microSD card problems with AKU2.3 ROMs!
Using a SanDisk 1Gb here no problems. Also using WM5 Build 14955.2.3.0, which is AKU 2.3 is it not?
Mine is the HERM300 (MDA Vario 2).
help
hi I am usin 1gb kingston with hermes.and its speed is too slow like 30kpbs via wm5 storage.I think I need to format my card correctly.any help?
and can any body tell me any tweak to have programs install on folders of my own choice?
thx in advance.
it is a pleasure to write from hermes .....hehe
Kingston 2GB made in Taiwan
Often not responding after loading for a few times. Need to be inserted into the device again.
Toshiba 2GB made in Japan
No problem until now.
Wow, I've got something different!
1GB Corsair MicroSD in my Imate JasJam.
Worked flawlessly for 6 months until I became the new owner of both phone & card, it then had card detection issues for a couple of days, but came good on it's own.
Now on WM6 and still working fine. I'm wondering if larger than 2GB cards will work.
Cheers! Oggy.
I purchased a SanDisk 4gb microSDHC and it DID NOT work!!!
I am now back to using my 2gb A-data microSD (which works fine).
No problems with my A-Data MyFlash 1GB, although once or twice I did have to use a tweezers or a needle to extract it. Just FYI, I bought my card on NewEgg.com, and people there usually leave feedback on if the card worked or not on their particular mobile device.
Very interesting.
So it looks like some people have 2GB Sandisks with NO problems.
Mine pops in and out quite nicely, actually. Although on my dad's unit, you need a tweezers.
Typical......!
jeffreyj900 said:
If only it was that easy. For some reason, mine doesn't do that. I push in, it doesn't pop out
Click to expand...
Click to collapse
I have a 8525, had that issue on day 1 and it was driving me crazy. then I thought let's put a needle down there and see what happens!! the thing lost its virginity, now pops in & out just fine
BTW I have Sandisk 2GB microSD card (Made in Taiwan) which works fine, I just have to eject and reinsert it in sleep mode.. else i'll have to SR so that the device would recognize it.
micro SD not reading
My unlocked M3100 has stopped seeing the storage card - nothing wrong with the card (tested elsewhere), and it used to work (on M3100). How might I rectify this?
juann said:
My unlocked M3100 has stopped seeing the storage card - nothing wrong with the card (tested elsewhere), and it used to work (on M3100). How might I rectify this?
Click to expand...
Click to collapse
Check this thread.
http://forum.xda-developers.com/showthread.php?t=294324
Mike
My SanDisk 2GB Taiwan card would disappear every other day or so. It wasn't a huge problem as I'd just have to pop it out and push it back in to get everything working again, but I needed another microSD card for another device so I bought a Kingston 2GB hoping to get a Japan card. I ended up with a 2GB Kingston Taiwan card, but it works just fine (a month now) without disappearing *knocks on wood*
Michael_514 said:
I know that the 1GB Made in Japan Kingston seems to work flawlessly.
Click to expand...
Click to collapse
I have occasional problems with a 1GB Made in Japan Kingston, so I have to disagree with your statement.
I am convinced that this problem is hardware related. Either a connector fit problem as Michael Channon believes, and/or a motherboard problem as I believe. Earlier Hermes motherboards were manufactured by Hitachi, HTC now uses a different supplier for their motherboards. Rumour has it that the Hitachi mobo's have a problem with the mSD card hardware (could be the same problem I s'pose).
John
Sandisk 2GB card
I also have a Sandisk 2GB.
It had trouble ejecting the first few times and I had to use tweezers or the tip of a razorblade to get it to slide out but after a very short time it started moving normally.
My 8525 does lose site of the card from time to time and I sometimes have to re-insert it several times before it is recognized but I have not had to reset the phone to get it to come back.
Hello guys, i've just bought a vodafone v1605 Hermes, after having a bit of fun with it i've bought a microSDHD 4GB cause i wished to install TomTom...
I've inserted it, and after going on settings/memory or file explorer, i couldn't see the extended memory =(
I've tried shutting down the device and turning it back on... but nothing to do... (i've also tried to remove and insert it several times)
After that i've tested it with the adaptor on my PC and it works! =/
Strange thing...
Than i remembered that somewhere someone was talking about the fact that it's needed WM6 to see microSDHD on the device, so i've installed blacksatin, last radio version and last spl but nothing to do... my device can't see the SD card... =(
Now i'm guessing if it may be possible that my device microSD reader is broken... but i really hope not!
Has someone else had this issue?
Is there something i forgot to do? some setting, or something to flash on the device?
Just to assure that it isn't a microSD reader problem, today i'm going to buy a microSD 256mb, let's hope it will see the extended memory card..
All suggestions are appreciated... Thanks!
I had a similar problem after first buying a micro sd. The cause is from pushing it too far in. The hermes micro sd slot is deeper than the sd card is supposed to be put in (by about 1mm). If you insert it until around half a mm is still pertruding it should be ok.
Thanks for the suggestion OdeeanRDeathshead i've tried also this solution... but nothing to do... =(
Just for curiosity, when i insert the microSD and i'm in memory page, should i see it immediatly if the device recognize it? or i've to reboot or "reload" the page?
Ty!
Ok, yesterday afternoon i went to buy a new microSD 1Gb (great offer, i've paid it 13 euros for a promotion) and it works without any problem... so now i really can't understand why the device can't read the 4Gb...
It is an orginal SanDisk MicroSDHC 4Gb... =/
My only doubt is that the device can't recognize this high capacity SD... =(
Am sure I read elsewhere that you need to format the card in a PC card reader (SDHC capable) and then put it in the phone and format again - or something like that.
crazyC said:
Am sure I read elsewhere that you need to format the card in a PC card reader (SDHC capable) and then put it in the phone and format again - or something like that.
Click to expand...
Click to collapse
at this point i think that this is the missing passage...
i'll try this soon and report...
thanks crazyC!
MicroSDHC cards are not compatible with some WM5 ROMS. What ROM are you using?