ok
I was updating the radio, when the power went out....
did I ruin, my jasjar
what can I do, all the screen says is serial on the top and v1.00 on the bottom
now what ?????
Reconnect it and reflash the full rom for your device. It should connect and work ok. I think the roms for each network etc are all available on this site.
I had this recently when I updated my o2 rom. I downloaded the rom file and ran it but active sync kicked up and I got the screen like you said - couldn't get out of it at all, but when I tried running the rom install again it worked and went through ok.
You could try the radio reflash again, but it's looking like you need the full rom first.
well like everything else in my life, it not that easy
when I connect to active syn, it tell me unknown device connected
it is like a hi fi brian treaser
connect the device. You will see usb message on the screen and activesync WILL NOT connect. Then execute the update again....
I had this a few weeks ago, try a hard reset, press the two keys with the lines accross them at the top of the keyboard, and at the same time press the reset key. when it comes back up with the grey screen select the option to continue and re-dock the PDA to re-start the install, it worked for me - good luck - Mike
Hi Friends,
My new mobile phone SPV M600 got stuck whil starting showing four lines of messages as shown below.
IPL 2.10.0001
SPL 2.10.0001
GSM 02.07.20
OS 2.10.1.22
Can any one please help me in geting my phone to today's screen.
I also attached the screen shot for reference.
did you try a hard reset ?
Ya I tried both hard as well as soft reset but same screen is stuck again and agian.Can any one please help me in this regard as I am very new to PDA family.
Ok, first things first:
Since you are new to this, are you sure you preformed a hard reset?
It is done by holding power + camera + comm manager buttons (one on the right, two on the left) and pressing with stylus in the reset hole at the same time.
A message should appear asking you to press 'send' (green phone button) to confirm reset.
If this does not help, you may have a serious problem.
Please answer the following:
Is the device fully charged?
Phone will fail to boot if the battery is too low.
Did you install any software right before this happened?
This should have been resolved by hard reset, but just in case I am asking.
Did you change the ROM, attempted CID / SIM unlock?
This could require more serious measures than I can advise on.
I did exactly the same thing which you mentioned.But even then it is stuck at the same screen.
Ya u r right I unlocked my mobile using a software from eBay.The unlock was successfull and I tried to insert T-Mobile sim, it also captured the signal and I was able to make and recieve calls then after that I wantedly switched off the phone and then tried to start it, there got the problem.
Can any one help me in this regard please.
I am having the same problem, but my phone is not sim-locked.
I've got the same problem after attempting smart1_wm6_pp8mb.exe
I'm having the same problem with my G4 QTEK S200:
Attempted to upgrade to WM6 Rom using smart1_wm6_pp8mb.exe
After reboot the phone got stuck at the QTEK Screen
Tried Hard Reset (Camera+Power+Comm+Reset) followed the steps with the same results (bricked)
I also tried re-flashing the rom back to the factory one using RUU_Prophet_220734_2207114_024721_QtekWWE_Ship and ROMUpdateUtility-NoVendorID.exe in Windows Vista with WMDC (Windows Mobile Device Center v. 6.0.6873) and the phone in boot loader mode (tri color screen) with working USB cable, with windows firewall disabled and symantec AV disabled as well, RUU keeps saying error 260 "the update utilitiy cannot connect to your pda phone..." .
Do you think I should try this process using XP instead? No matter what i try i keep getting the error 260
Any help would be greatly appreciated
Got it fixed!
it was definately a Vista issue. once i tried it in XP with ActiveSync it worked like a charm and i got my phone back up and running. also used spb backup and restored all my settings.
ipl/spl screen
i got the same problem with new rom wm6, and the 260 eror, my problem is that i have xp and the activesync does`t connect ...
... means i cant redo the original rom ????
PLEAAASEEE HELPPPP !!
Again My phone SPV M600 got stuck at IPL/SPL screen
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
yekanth said:
Please Can some one advice me how to get my phone back.
I raised the same issue 7 months back after that my phone got recovered automatically and there were no issues till last month. Last month onwards it is again got the same problem and now it is permenantly stuck at that screen what ever you do.
Click to expand...
Click to collapse
A rom reinstall on xp solved my problems on that one. retry a couple of times! It may not work the first time! hard reset as well...
Try an official wm5 rom just in case
good luck
Can you please gimme step by step procedure
HI Phil,
I am new to these kind of installations . CAn you please Gimme step by step procedure for ROM installation.
mine is now also stuck, after trying to install new rom. wont connect to active sync either, have i fooked it? tried hard reset etc.
thanks
(with a turned off phone, press and hold camera button then insert USB cable)
then flash provider ROM
RECOVERING FROM ERROR IN STEP 8 WM5->WM6
1. Don't panic
2. Don't panic
3. Unplug the phone
4. Reset with stylus,and keep the Camera Button pressed.
5. A 3 color screen will appear(Bootloader Screen)
6. Connect your device with your PC,and run the NVID(no vendor) WM5 rom.
7. The device will be resetted after RUU(rom update utility)finishes
8. Repeat the WM6 upgrade,from STEP 5..
Click to expand...
Click to collapse
from here http://forum.xda-developers.com/showthread.php?t=310452
hi jay
i seen your post in n00b guys one, i fixed it!!!!, thank you so much, i couldnt remember how to get it to those 3 colours.
thanks again
Colin
Hi Iam unable to get the NVID ROM
Hi,
I am unable to get the NVID ROM. The Rapidshare link that has been provided in the other thread is not working. Can some one tell where can i get the ROM.
collywog19 said:
i seen your post ...
Click to expand...
Click to collapse
no problem mate.
..and yekanth i see what u mean about the dead links. i have the files on my computer at home but i'm posting from my prophet right now, so i can't upload. Try using the "pdaviet temp" from one of the wm6 threads?
(http://rapidshare.com/files/54265407/Prophet_PV_Temp.zip)
Hi Iam able to update the Rom but no use
Hi,
To mention my phone is from orange-UK. I got the orange rom from our FTP site and did the flashing/update what ever you say.But still it is getting stuck at the same IPL/SPL screen. Iam very much worried that I will not get a proper solution for my problem.It will be very grate full if some one resolve my problem.
just seems strange...how did you fix it last time? did it just start working again? A random guess would be that the camera button got liquid spilled on it or is stuck in.
If the camera button is pressed in the phone will go to 3 colour screen every time it is turned on.
It won't do any harm if you try to press/move that button to see if u can "unstick" it, not likely I think but u never know...
Hi my friends. I hope you help me in my problem. I have a prophet. For a long time i had installed wm6 touch evolution rom. This afternoon i had the phone closed and when i turned iit on it didn't load windows but when the windows mobile screen appeared i heard a sound and the phone turned off. I restarted and restarted for many times but nothing... I did a hard reset but the same problem. The bootscreen appears and when the screen changes to windows mobile bootscreen i hear a sound and then the device stuck. I installed the same rom i already had but the same problem. Then i decided to install the original rom O2 Germany but for one time again i had the same and the same problem. What can i do? Can this problem be fixed?
Hi guys. I think that i have find what is going wrong. I reinstalled O2 Germany rom and when the installation finished the phone is restarting. That time i didn't discinnected from usb cable and the phone didn't restarted or stuck. Is it possible that the batterrie has problem? The phone is starting only if it is connected to current via usb or via electric charger. Is this possible? My batterrie didn't have problem since this afternoon. When the batterrie was fully charged its duration was 2-3 days. Please give me a reason
Hi there,
I've got an XDA Orbit that used to be on an O2 contract (I now use TMobile).
I've currently got HTC Home installed but I'd like to flash the ROM using the Armetis Touch 4 ROM.
I've tried running start_uspl.exe but it doesn't reboot the phone so I can't connect to ActiveSync to continue onto the flashing part of the process.
I've tried a couple of times and it just gets to a point where the only thing I can do is a soft boot.
Is there something I'm not doing right or is there a different process I should be doing?
Cheers,
YP
Hi, I am also having the same problem as this with my O2 XDA Orbit - it seems that when the phone reboots, it shows a white screen and cannot continue the process. Any help would be great please
The white screen is normal.
You do not need the activesync to continue the process.
Just wait a while at the white screen. That's for updating your SPL.
After uspl finishes I get RUU, but then phone allready has wtite screen and it can't continue flashing cuz RUU is telling that there is no phone connected.
I flashed it once (WM 6.1 with cube) lost tons of nerves cuz of that, but it slowed down few days ago, gwes in task Mgr has "X" so I guess that is the cause of its slowlyness.
Hi there, I've been reading the forum for about a week trying to find a fix for my deceased orbit xda.
Problem started when the phone started crashing, the screen was going white and needed re-starting. Eventually it failed to load and froze at the blue screen with the red writing!
so I started reading and tried soft and hard re-booting to no avail.
I have managed to get the phone into bootloader and connected a USB
it recognises the usb and installs as a mobile device on my laptop but here's where it gets tricky. I dunno alot about phone's and am struggling to understand some of the processes. I have tried booting off the SD card but it said invalid certificate (i used the artiemg.nhb file from rapidshare)
I have all the original paperwork and cd's for the phone but dont know what or how to flash a ROM.
what do I need and more important how do I do it without all the tech talk.
Its a WM5 phone - thanks
EDIT - Just to clarify, have just tried the romupdateutility on raving_nanza's sig but recieve an error - am running vista on my laptop
Update, I managed yesterday to get the phone to boot from the SD card and indeed it flashed it and WM5 is back up and running, the new problem is its network locked (to O2 i presume). I was using this phone on orange previously without an issue????
any Idea's other than paying imei check?
...
danv6saxo said:
just tried the romupdateutility on raving_nanza's sig but recieve an error - am running vista on my laptop
Click to expand...
Click to collapse
what link was it?
what error did you have?