BA doesn't recognize SDs after WM6 upgrade - MDA III, XDA III, PDA2k, 9090 ROM Development

Hello,
since I'm running Helmi's WM6 on my BA I can't use any (non-SDHC) SD Cards anymore. The storage card is neither shown in explorer nor in settings\storage\storage cards ("Card storage: not installed").
Do I have to install any drivers first? Where can I get them?
Edit:
Okay, a reset solved the problem - everything works fine now!
thx, bj_b4

Related

Memory card problem

After using my vario 2 for a while the mem card becomes unusable.
It's shows no free space at all. I have a 1 gb memory that came with my t-mob vario 2.
My mp3 ring tone doesn't work anymore. I have to remove and reinsert the memory card or soft reset the device.
Radio 1.20.31.10
Rom: 1.21.114.3
Any idea's what could be the problem?
Thanks
The smilar problem occured with one of my XDA-II (Himaliya), Even though I have hard reseted the device. Finnaly I have backuped the card through the pc and format the card (on PC) and it wasn't working, even though I have tried 3 other cards and they were working absolutely fine with the device. What I did was to leave the card inside the device for overnight and it was recognisable in the morning, then I took out the card from the device to put the data back from the PC and once I have put the card back in the device the card wasn't recognisable again, So finaly I left the card again in the device overnight and it was recognisable again, then I left the card in the device and put the data back through the syncronisation.
I haven't taken out the card since then because I know there is some recognising problem between the device & the card, its working since then.
My Advice is : To check another card and if that would work then try to sell your current card and buy another.
My advice 02: Try to backup your device, leave the card inside the device and HARD Reset the device & once the device will install newly it should configure the card as well.
I have got very usefull software "storagetools" (trial) by which you can scan, format & defrag the card, you can try it.
GoodLuck
Sidd
Use chkdsk on the PC to check your storage card (instead of any PPC-based software, including Storage Tools). I also recommend the thread at http://www.pocketpcthoughts.com/forums/viewtopic.php?t=39583 on all these q's.
On a related issue concerning problems with microSD cards and the TyTn, I have a problem which I hope you can help me with:
I have a new TyTn (ROM Ver. 1.18.255.3) with a 512mb miniSD card. In the course of my usual usage, the device hanged and after a few minutes of unresponsiveness, I reset the device using the reset button. When it rebooted, the card is no longer recognized by the phone. I used a card reader and WinXP and Mac OSX cannot also recognize it. If I try to format it (XP), XP says that the card cannot be formatted. I tried using it in my Samsung D820 and it cannot also be formatted. I then concluded that the card was defective and bought a new one (512mb).
After using the new card for a week, my TyTn hanged while accessing a program installed in the card. Again after a few minutes of unresponsiveness, I rebooted the phone using the reboot button. When the device booted-- Bam!!! the card can no longer be recognized by my phone! Windows and Mac OSX cannot mount it. I tried the unrecognized card in my Samsung D820 and it is recognized! I inserted the miniSD card (128mb) originally in my D820 in my TyTn and it is recognized/read by the TyTn. I formatted the defective card in the D820 and copied a few files in it and the D820 can read those files but my TyTn can't! I tried the other 128mb card on my TyTn, formatted it and copied files into it and everything's fine.
How come then that the 512mb card can be read by my Samsung phone and not by the TyTn? My TyTn is certainly not defective because It can access the 128mb card that was originally in my D820. As I stated earlier, I have already formatted the 512mb card in my Samsung phone and have transferred files into it (The Samsung phone can read the files written on it).
I have re-inserted the 512mb card numerous times in my TyTn to no avail. I have also rebooted my TyTn several times and still it cannot recognize/read the 512mb card. I am now using the 128mb card that I originally use in my Samsung D820.
If it can help, I have enabled and unlocked my TyTn's extended ROM. I have a few programs that are installed in my Ext ROM.
Thanks!
Similar card problem
I recently purchased the T Mobile MDA Vario2 with the CoPilot 6 software. worked fine for about a week and then the CoPilot software which was running from the memory card started to hang intermittently. The first couple of times a soft reset cured it. Then after about the third soft reset, the memory card was no longer recognised. Tried reading the card via my pc and that couldn't recognise it either.
Took both the phone and card back to T Mobile where a new card was tried, this was recognised immediately so I now have to take the whole CoPilot package back to be replaced.
I have also just orderd a new 1GB sandisk card from Amazon and am now concerned that this is going to be a repeating issue. I wonder how many other owners have had this problem and if it is actually a fault with the Vario2 or wether I have just been unlucky with a dodgy memory card.
Would appreciate other thoughts on this.
Cheers
Matt
I think that enabling the "Advance network functionality" causes the corruption of memory cards.
amf said:
I think that enabling the "Advance network functionality" causes the corruption of memory cards.
Click to expand...
Click to collapse
How did you work that one out?
Elwyn M3100 said:
How did you work that one out?
Click to expand...
Click to collapse
Because when I enabled it, the corruption started.
amf said:
Because when I enabled it, the corruption started.
Click to expand...
Click to collapse
Hmm, yes, I can see where you worked that one out

memory card problem.. not installed

I use atom with sandisk 2gb memory card. i have formated my card with pocket mechanical Pro. software with it's default settings.
now in file explorer and storage place it says memory card is not installed.
i did soft and hard both reset. upgraded my rom again as well.
but helpless..
any solution guys?
Try using Resco Explorer or SKTools to format the Card in your Atom
problem solved.. i did install memory card in computer and formated it with FAT system... n it worked for me...
^does file explorer show its correct size?^
Hey guys I have also developed a problem with my memory card Sandisk 2 GB. I upgraded my Atom Exec today in the morning to the great WM6 AKU 7a of chartreux after install when I inserted the card my atom did not respond. I tried the card through card reader on my PC and it was working perfectly. Then I tried another 2 GB card of Kingstone (one of my friends) but my Atom Exec did not read it. I flashed the old original ROM from O2 but even then my Atom Exec is not reading the card please Help.

Storage Card is not detected?

Guys,
I have use my BA w/ several roms from WM6.0 to WM6.1 but suddently about a week ago, my phone is 'freezed' and need to be hard reset...and since then my storage card is NOT idenfitied. It said no storage card detected eventhough the MMC is there.
Any idea why?
did this problem occured with 2003 rom, have you tryed your MMC/SD card in card reader ?
never tried in in 2003 rom since i went to 6.1 rom ...was OK when i use it in 2003 rom
well i tried in my card reader and sait it need to be formatted...that might be the problem, isn't it?
Format the card in the card reader and this will solve your problem

Problens 2Gb card A9100 !!!

A9100 does not recognize my 2GB card i install this supplement "SDHighCapacity" but he will recognize the device turns off the WIFI.
how to solve this?
he recognized the card and run the WIFI?
VLW
Note I have the ROM BlackDiamond 3.1 Touch
Qtek A9100 G4
thanks !!!
my Wizard is able to read 2GB MiniSD card without any program.. Have you formatted it with PC before?
yes, my Qtek A9100 recognizes MiniSD CARD 2GB,but i have a 4GB SDHC Card
which is not recognizes.
i have alredy installed the "SDHighCapacity" and it is working now(he reads the 4Gb SDHC card).But when I intall it my wifi is desable and i can not enable more.
I have done a soft reset its nothing dont work wifi
What could be causing this problem?

SDHC Card Driver

Hello,
when I plug in my 8GB SDHC Card in my Touch 2 Phone, I can't see it :-(
I remember....with WM6.1 I installed a SDHC driver, then it worked perfect.
Is there any driver for WM6.5 available?
Or how can I fix this problem?
Kind regards,
Philadou
htc mega recognizes 32gb sdhc by default. i think ur card is faulty
Empty your card and re-formatting may help.....
ok, thanks.....i tried another card....sandisk works fine

Categories

Resources