Database Users

My Wallaby GSM Error fixed! Finally!

Hi all,
Hope I may be of help to those who have GSM Error on their Wallabys. I have almost given up hope but I just searched the threads. This is basically what I did:
1. Download xda developers special rom and re-flash via sd card
2. Hard reset, press contact and calendar buttons (or a combination of both), volume button, and soft reset will bring you to the today homescreen (I cant remember exactly what buttons I pressed, I just pressed them all)
3. Re-boot phone, you will notice you still have no radio but you can now enter today homescreen (please take note the "start" menu is not there)
4. Align screen / stylus. You can do this by pressing Action Key then Calendar button.
5. Press Contact and Action Key (both) several times (I think around 20 times). You will hear clicking sound. This will bring out the "start" drop down menu. If it does not pop out, repeat again.
6. Download the correct RSU for your phone. Save into SD and copy to programs (same procedure as in wiki)
7. Run the RSU program, expect to fail at 1%. Re-boot. this time you will be able to active sync your phone again. (my wallaby did to my surprise)
8. I gave up on the RSU 4.16 (after countless tries) and I downloaded RSU 4.21 from xda-developers ftp (exe file) since I am now able to sync to my device.
9. Install RSU upgrade to your device, the phone will automatically re-boot.
10. Surprise! I was able to re-flash the RSU! (I think the problem is the RSU 4.16, try other 4.xx instead but be careful to use the correct version)
Now my Wallaby is up and running again! Thanks to xda-developers and Wiki and to Lumpi. There is no secret. I just did a lot of reading from the threads. It's all there. Good luck guys! Merry Christmas!

Stuck in Bootloader

Hello,
i tried to update my BA with wm6.
after flashing it stuck in bootloader(blue,green,red,white display) with the line "R 1.10.00" and nothing more...
even hard or softreset do nothing.
what can i do?

ok i even try the Stuck at startup method.
that's the output of Multiport TTY Version:
set 14 0
HTCST ÚÈÒHTCEUSB>task 28
DOC_format_HW+
DOCInfoTableinitHW+
Binary0:dwSize=80000
BINFS0:dwSize=0
FAT0:dwSize=1000000
FAT1:dwSize=2BA0000
All:dwSize=3C20000
USB>task 0
it always stuck in blue,green,red,white screen after run multiport tool. what can i do?
------------
i have this problem because of this flashing method:
i entered the grey screen (with serial/usb in first line). then i put my usb connection on and run the rom_update. after it is finished (succesfully) it stuck in the blue, green, red, yello screen! help please...

how did you hard reset?

hello,
i hold down the power-button and at same time put stylis in reset.

hard reset for both WM5 and WM6 is different from the one you're doing. here's the guide...
http://wiki.xda-developers.com/index.php?pagename=BlueAngel_WM5_For_Beginners
good luck!

ok thanks, i have tried this:
i do softreset. whenn the stripes came i push "records and "camera"(media player button because there is no camera)---> nothing happens. it stops with the line R 1.10.00 and the coloured stripes.
i dont knwo what to do.
the bootloader method is running. i hold power and record button while i softreset. but with color screen it wont work.
they is no camera button (it is media-player button) because there is no camera. its an german xda III (blue angel).
the next problem is i dont knwo what os is right now on it. befor flashing it was wm2003 and flashing says it was successfully. i dont know if its wm6 or wm2003!

ok now all is happen...
the xda says nothing. it dont go on, it dont work anymore. no lights when in cradle, nothing.
can i do anything?

1. Take the battery out, wait a moment, put it back, do not turn on. Put in the cradle and try to charge it. Use power connection (from power supply), disconnect USB from the computer for charging. Amber led should turn on.
2. When it will be fully charged (amber LED will turn off) try to turn it on and enter bootloader. Try to downgrade to WM2003. If it works fine, try again to flash WM5 or WM6.
What you did seems to be wrong update (wrong rom, wrong file, not fully flashed). But you still have bootloader, so it should be possbile to flash it. But you need full battery.

jakubd said:
What you did seems to be wrong update (wrong rom, wrong file, not fully flashed). But you still have bootloader, so it should be possbile to flash it. But you need full battery.
Click to expand...
Click to collapse
it was not unlocked befor i flashed with bootloader-method.
i charged the battery in cradle (withoud the blue-angel). the led first went orange, after a while turned green (fully loaded). put it back in BA an nothing happens. then put BA (with battery) in cradle and the led became red.
no action on devide, no feedback, nothing. it wont turn on but led is still working.!?

jakubd said:
2. When it will be fully charged (amber LED will turn off) try to turn it on and enter bootloader. Try to downgrade to WM2003. If it works fine, try again to flash WM5 or WM6.
Click to expand...
Click to collapse
ok i get it. in display is the "USB" & "v2.07". now i can flash. but my problem is the phone is not unlocked yet. what file can i flash now??

This message tells you are in bootloader mode. Now you can perform normal flash - I would propose you to use tested&working rom (WM2003?). If this works fine, try again to upgrade to WM5/WM6.
BTW: if you disconnect USB (take out BA from cradle) it should show Serial instead of USB.

ok big tanks to the forum. i finally get it. wm6 german on blue-angel!

Same thing here... but worst..
My 9090 is stuck at bootlader...
When i try to update, (i press the power, record and reset), it says:
SERIAL (or USB)
DOC VERSION IS ERROR!
v2.08
Any idea???

that's normal...
try to flash/update your BA in that screen.

the easy way to go into bootloader mode is to execute a file called Enter Bootloader.exe ..it comes with the rom u download..( well it came with xplodes )
Note:- you have to execute this file directly on your deive not on your desktop PC...and i have only tested this on WM 2003..maybe it will work with wm6 also

SilverSamurai said:
that's normal...
try to flash/update your BA in that screen.
Click to expand...
Click to collapse
I there...
I just updated to BA_TMNL_14200_119_11300_Ship, but only with Maupgrade, couldnt do it with baupgrade...
The problem is that i cant put extended rom, whem i try to upgrade is allways an error... and in the settings i dont have extended rom instaled...
Besides that the batery only last 1hour and the PDA is always freezing... i'm always doing resets...
any idea??
Sorry for my bad english by the way...

HTC Polaris/Cruise (XDA Orbit 2) bricked.

Hi everyone,
I recently received an XDA Orbit 2, literally, charged it for 2 hours, and when it was full charged, I started using it, I had it for about 2 months now, and recently I changed my home Internet connection to wireless (It's a B & G connection) so my laptop connects fine, and when I tried to connect my XDA Orbit 2, it connected and then soft-reset itself, and now it just loads the O2 screen, then Windows Mobile screen with the volume controller and I can't do anything else so here's what I have tried so far:
- Soft reset
- Removed battery and SIM
- Since I can't access phone's menu at all, I tried to Hard Reset method by holding the 2 soft key, reset, and the power button - So I get the warning that everything will be lost and to press 'Send' to continue, so I press the green key, and soft resets and goes back to the same situation again.
- The latest thing I tried is to load the Hard-SPL into the SDCard which has been formatted to FAT32, so loaded the POLAIMG.nbh into the root. and loaded the phone into BootLoader mode (Camera and reset buttons). It loads the memory card and just says 'Loading ... ' I left it for about an hour, until the battery died completely (I'm sure it's not supposed to take that long). And still the same problem.
I'm not sure if this phone is now bricked, can anyone help me plesae. I really need this to start working again, I don't have any info. on it. (Everything was sync. previously).
Kind regards,

Since you havent really messed with SPL, i would say to take it back, since its still into warranty.

Thanks for the reply, I'm not actually in the UK and will be overseas for a while. I don't really mind experimenting so I would appreciate any advise on this matter. Thanks again.

htctytnowner said:
Thanks for the reply, I'm not actually in the UK and will be overseas for a while. I don't really mind experimenting so I would appreciate any advise on this matter. Thanks again.
Click to expand...
Click to collapse
I assume just boots into bootloader and then stays there?
If yes you culd try searching out a thread on MTTY and recovery from boot loader but I dont know how well that would work on polaris as I have not tried it yet.
HTH
Leon

Thanks for the reply, I heard about the MTTY process, but I've no clue on how to do it, since the phone can't connect in ActiveSync mode. Is there a thread or WiKi guide out there?

htctytnowner said:
Thanks for the reply, I heard about the MTTY process, but I've no clue on how to do it, since the phone can't connect in ActiveSync mode. Is there a thread or WiKi guide out there?
Click to expand...
Click to collapse
Only in the ELF forum
Here:
I'm pretty sure you can download MTTY from here and read through how to use it.
http://forum.xda-developers.com/showthread.php?t=347700
Also it is worth checking the wiki and searching
http://forum.xda-developers.com/showpost.php?p=2054848&postcount=38
Please do some research! I have not done this before and I have no idea what the commands do!!!
pqillu said:
You can try this:
Originally Posted by christonge
1. Stop ActiveSync
2. Open Task Manager (press Ctrl + Alt + Delete) on your PC and
stop these two processes rapimgr.exe and wcescomm.exe
3. Plug in your device via USB. Your computer should be asking install a driver. Install and continue.
4. Now Run mtty and choose USB in 'PORT'
4. type "set 16 0" without the quotes to tell bootloader to boot the OS after reset.
5. type "task 8" to get your device formatted.
6. Now unplug your device and manually reset it.
THX to christonge
Good luck.
PQillu
Click to expand...
Click to collapse

Please Heeelp!
I wa installing a rom from todopdas.es an my Polaris doesn´t pass from the screen where´s said "smart mobility", and R1.58.21.23 G 25.65.30.04H D 1.52.00.00, please what I can do?

You need to do Hard Reset, all information will be wiped off. To do hard reset, hold down the:
1.Press and hold the GPS/MESSAGING and INTERNET EXPLORER
buttons, and at the same time, use the stylus to press the RESET
button at the bottom of your device.
2. Release the RESET button, but
continue pressing the GPS/
MESSAGING and INTERNET
EXPLORER buttons until you
see this message on the
screen:
This operation will delete
all your personal data,
and reset all settings
to manufacturer default.
Press Send to restore
manufacturer default, or
press other keys to cancel.
3. Release the buttons, and then press SEND on your device to perform
the hard reset, or press any other button to cancel the reset.
Good luck.

Hi,
I'm using an HTC TC POLARIS100. Today I upgraded my ROM and SPL successfuly. If you're still in trouble and believe the same process will help, I will let you know the process followed.
GUY

qtek 9000 doesn't turn on

first i'm sorry for my english i try to explain my problem in best language
i have a qtek 9000 and one hour ago i flashed my phone with Ranju_v76_WM61_19209_19209_1_0_2.exe (sticky topic) and this operation finish correctly.I used wm6 for abouy 5 minutes. suddendly my ppc turn off and doesn't power up but if i press keys for hard reset it power up with press 0 to restore factory or X...
If i press 0 my ppc turn down and doesn't power up.
If i try to connect in my pc windows xp write "Periferica non riconosciuta".
how can i do?

Hi Alex, well, have you tried to enter in bootloader mode and re-flash with your prior rom?
Also, you might want to try a full hard reset to your device first.
Let me know if you need italian directions for this.

battery
Also check if your battery is old or try getting a new one and charge it and boot it up.
Mine was some what of the same problem, until i got a new battery and now it's working.

My XDA with the ranju rom did this over the weekend. Was working fine for weeks then turn it on after 2 days non use and its dead. Could the rom have an issue?

All sorted now via bootloader.

HTC hangs in bootloader after attempt to flash rom

Hi!
I have a HTC P3300.
I bought a 4Gb SDHC card, and it won't work. I read at the forum that I would need a different rom, so I downloaded "Artemis_Touch_4.02_Full_with_no_cube", which would have sdhc-support.
Then I executed "STEP 1 - activesync then uspl cid unlocking.bat", that finished ok, and then "STEP 2 - activesync then flash artemis touch rom.bat", which stopped with an error 302.
After a restart all that came up was the boot loader. I then tried to flash the original rom (HTC WM6 Dutch) from the computer, but that ended also in an error.
I tried the SD upgrade (rename .nbh file to ARTEIMG.nbh, put it on a formatted sd-card and load it in my phone), and it finished without errors, saying I should press any key.
After pressing a key, the bootloader popped up again.... :S
Can anyone help me? I have been searching the forum and trying to get my phone to work since 21:00 and I haven't got any progress at all!

well sorry for that
did you tried to make hard reset?
and once i had a completely dead artemis.. no sign of life..but it fixed by the following..(and maybe this may help you cuz the flasheng goes not like usual)
while your mobile is off.. press the record botton and the camera and it should starts with usual sd card flashing.
for me this what happens.
the setup was in three phases as i saw... and it took about 30 mins .
maybe it will works for you

I also tried a hard reset, wouldn't work.
I pressed and hold the camerabutton, but nothing happend...
Maybe the battery is empty, so I pressed and hold the camera button while plugging in the usb-cable.
It started the SD-upgrade, and is still busy.

The update ended with a "press any key to continue".
But when I pressed a key, the boot loader popped up :S
When I tried to flash another rom (NLD-FINAL), an error occurred (I believe it was error 270, not sure).
But then the normal startup screen appeared!
I don't know how, but the problem seems to be fixed!

sorry i mentioned the wronge button before..
try to start flashing by pressing the RECORED button and the power.. while your mobile is off.
and be sure that you copied the original shipped ROM to your device (NOT elese)

As you can see in my previous post, I managed to flash the original rom.
I'm gonna try to upload an other rom some other time...
And with a patch I got the SDHC working too!
Thnx for your help!

y_bother said:
sorry i mentioned the wronge button before..
try to start flashing by pressing the RECORED button and the power.. while your mobile is off.
and be sure that you copied the original shipped ROM to your device (NOT elese)
Click to expand...
Click to collapse
Hey, thanks a lot, I tought, my HTC-Cruise is ready for sending to repair, but with your info, it works again. I could install the WM 6.1 again, after System hangs up while booting every time. He found USB connection on a colored sreen. Thank you very much.
Jupeli