Bricked Herald - Wing, P4350 General

Hi there.
I am going to buy a very very cheap new Herald.. One bad thing. It's bricked. But bootloader (Tricolor) runs. My question is: How to flash official WWE ROM WM6.
(HTC_P4350_SPA_4.17.412.2_4.1.13.44_02.94.90_Ship.exe)

What IPL / SPL version does it have?
If its lower than 4, you may want to reconsider buying the phone since it may be permanently bricked, requiring being sent back to HTC which will only mean more $$$
TO check the IPL SPL version, you need to go into bootloader mode, which means hold down the camera button and soft reset the phone (sticking the stylus into the reset button the left side of the phone under the volume slider) while keeping the camera button pressed the whole time until you get a tri color screen with the version numbers. If they are less than 4something... you run the risk of permanently bricking the phone

ok..
Bootloader seems to be showing this:
IPL 1.11.0001
SPL 1.11.0001
USB
This is not good, or yes?

Ok, another way...
In attachment is picture of bricked Herald. Is any way to unbrick it - WM5/WM6?

Stock RUU ?

Are you guessing or you know what I have to do?

The problem with having an IPL/SPL thats less than 4x ... is that from my understanding, once its bricked ... there's no way to fix it without sending it to htc..
If you buy any chance have a stock ruu to try to run on it, but i don't know if that would work.
Try one of the htc roms from the herald wiki

HMmm.
To big risc for me. I don't know if that would be unbricked. I am go away from it. Sorry.

Related

Bootloader gone ???

I have a Herald 100, wanted to upgrade to WM6.1, Originally had IPL 1.08.001 and SPL 1.08.001, did Hard-SPL 4.7 as per Instructions, Phone switched off and never restarted, went into Bootloader and showed me IPL 1.08.001 and SPL 4.7 Yan then I soft-reset and now its dead wont even go into Bootloader anymore. Any one can help ???
you aren't supposed to HardSPL with an spl less than 4. You may also need a higher IPL, but i'm not sure.
I've also heard reports that even with the 1.08.001 IPL and SPL, HardSPL still works.
So... to answer your question
1. try charging your battery
or
2. keep trying you might get lucky someday
or
3. you've utterly destroyed your phone and theres nothing else you can do
I get into the Bootloader again, IPL is 1.08.001 SPL is 4.7 Yang, tried with RUU 5.4 but Phone dies after 1% and i get Error 262. Do I have to install RUU 1.8 which was on originally now ??
i'd try it, but i don't know if it'll work
hardspl modifies the SPL, which is what controls the cid lock. my guess is that the lower spl doesnt quite accept the same instructions, which is why it doesnt work.
there are some threads about people who've made the same mistake and recovered their phones. look at those.
I can help you, contact me by PM
ps. Thanks for erase my last post
hey tramuyo, how exactly did you do it? There's been an increase in the amount of people that this happens to, and i'd very much like to have an answer and you seem to be the expert on this.
ps. whats that about erasing your last post?
Did you tried remove HardSPL?
Almost forgot, what model? Language? and make? You may need to restore the original rom to unbrick your phone
Try to do a hard reset. Hit both side buttons... and post results
Hard Reset shows me a Screen Canon Yang with Vodafone Logo and in the bottom right Corner: Now you're HardSPL. When i try and RUU with the original ROM i get no Connection.
On the RUU 5.4 the update starts and after 1% The Phone dies and the Update breaks off.
The Way i see it can either:
1. Remove Hard SPL or
2. Try this with the right Files http://forum.xda-developers.com/showpost.php?p=1848145&postcount=5
Problem solved, flashed with SD Card the Image from this Rom RUU_Herald_HTC_WWE_5.4.405.1_4.1.13.34_02.79.90_Ship.exe according to this Thread http://forum.xda-developers.com/showpost.php?p=2148052&postcount=27
Now I have IPL 5.04.0001 and SPL 4.70 Yang
Just wanted to mention, I have not been playing with WM for long, actually only since I own a WM Phone the last couple of month and this was my first Herald Experience, but therefore I have been flashing and fixing all other Cellphones for many years. The Herald Section in this Forum and the Wiki are not to well organised, could the Mods here maybe think of making a few Sticky Threads explaining the Basics to noobs in a Nutshell. I will post a new Thread later when I have a bit of time with my little Experience.

Hard Restart for MDA

I attempted a hard restart for my MDA using the comm and photo button technique, but all that comes up is 3 wide horizontal bands colored red, green, and blue with IPL 1.08 and SPL 1.08 printed at the top. Can anyone help?
You're stuck in bootloader mode. Possibly a corrupted extended ROM, but more likely just a bad flash, entirely. Connect it to the computer you usually flash from via USB. As long as you see "USB" in the lower right corner, you can flash and fix this.
IMPORTANT: Is your phone G3 or G4? If G3, was it CID unlocked?
If your phone was not CID unlocked, or if it's a G4 (and apparently doesn't have HardSPL installed), you're going to need to load the original T-Mobile ROM to the phone.
I'm not as well versed in the G3, but I THINK, if you are CERTAIN it was CID unlocked and is a G3, you can probably safely flash any of the cooked ROMs in the Wizard Mobile 6 boards.

error 260 update error [HardSPL upgrade] newb question

I am trying to do the HardSPL upgrade on an orange spv m3100 as per http://www.mrvanx.org/thg/index.php?option=com_content&task=view&id=16&Itemid=26 I have the lates version of WMDC running on windows vist and can sync etc no problem
When i go through the process it shows current image as 1.23.61.4 When i carry on in brings upenter bl.exe on the phone. The phone then goes into the bootloader screen and the WMDC shows disconnected
The programme hows verifying the information on your hermes Then I get error 260 update error cant connect
The current bootloader says.
HERM100
1PL-SSPL by Des
HERM100
SPL-1.09.ds
Any ideas and help would be grately appreciated
thanks in advance....steve
Plz help
my phone shows following details
SPL-1.09.ds
when i upgrade to HardSPL 2.60, it does upgarde but when after restarting it again shows the same version of SPL
i am now unable to soft reset my phone
and one more problem i am facing is that my phone shows HERM200while before this problem it was HERM100
this problem arose after i tried to downgrade to MFG bootloader
before that i had SPL 2.30
plz help
fcwdadmin, as you have sspl.exe already running (known as soft SPL - 1.09 des) format 2Gb or less sd card FAT32, put the .nbh file of Hard SPL V7 on and rename to hermimg.nbh . Reset to bootloader - hold power, ok button above flywheel and reset with stylus. Follow the prompts. This should put Hard SPL V7 on your phone. ONLY DO THIS IF YOU HAVE Soft SPL INSTALLED...
Go to bootloader to check, it should read IPL - 1.04 and SPL - 2.10 oli.
You should now be able to put any rom on from the Hermes section. I recommend using the sd card method for that too.
Cheers...
the bootloader says:
HERM100
IPL-1.01
HERM100
SPL-1.04
Is that the same thing again ??
Many thanks in advance
No, you don't have Hard SPL V7. I'd suggest going to the upgrade section and downloading the right Hard SPL. Its a sticky at the top.
Hard SPL V7 is the safest SPL to use as it offers a measure of safety that you don't otherwise have, making it at least possible to fix up your os if something goes wrong during a flash.
Read post 1160 on page 116 of the Hard SPL thread to find instructions on how to install it using the sd card method.
If you try to upgrade your os at the moment you stand a greater chance of ending up with a non recoverable brick or, at the very least, an agonizing amount of reading to just recover the os.
Hard SPL WON'T stop things going wrong but it offers a chance of recovery. V7 is the best for the person just interested in flashing roms occasionally (daily) so I'd suggest you get it.
It should read when you finish IPL - 1.04 and SPL - 2.10 oli.
No exceptions...
Cheers...
ultramag69 said:
No, you don't have Hard SPL V7. I'd suggest going to the upgrade section and downloading the right Hard SPL. Its a sticky at the top.
Hard SPL V7 is the safest SPL to use as it offers a measure of safety that you don't otherwise have, making it at least possible to fix up your os if something goes wrong during a flash.
Read post 1160 on page 116 of the Hard SPL thread to find instructions on how to install it using the sd card method.
If you try to upgrade your os at the moment you stand a greater chance of ending up with a non recoverable brick or, at the very least, an agonizing amount of reading to just recover the os.
Hard SPL WON'T stop things going wrong but it offers a chance of recovery. V7 is the best for the person just interested in flashing roms occasionally (daily) so I'd suggest you get it.
It should read when you finish IPL - 1.04 and SPL - 2.10 oli.
No exceptions...
Cheers...
Click to expand...
Click to collapse
I've been trying to find help with this everywhere, but none of the steps seem to work for me. Should I consider the phone brick now cuz I can't get Hard SPL v7 on? I was able to go up to 1.40 using CID unlocker, but have been stuck since then.
Can you get the Hermes back into today screen?
ultramag69 said:
Can you get the Hermes back into today screen?
Click to expand...
Click to collapse
No brick. I was able to get to SPL 1.40 and have been able to flash other ROMs. I've just read too many posts that says v7 is the way to go for stability sake.
Download Hard SPL V7 from the Hard SPL thread, go to page 116, post 1160 of the same thread for instructions on how to install using the sd card. YOU NEED TO FOLLOW THESE STEPS EXACTLY... One thing wrong & it won't work.
Afterwards, you can use these steps, dropping the steps using SSPL.exe (Soft SPL) to install roms. I find it much easier & safer than using the pc.
Cheers...

cant flash rom !

while trying some roms i stupidly removed hard spl
and now i cant install or flash any rom some local repair shops advised me to change motherboard do i realy have to???
mdrcute said:
while trying some roms i stupidly removed hard spl
and now i cant install or flash any rom some local repair shops advised me to change motherboard do i realy have to???
Click to expand...
Click to collapse
did you try to reinstall hard spl again?
check this out http://forum.xda-developers.com/showthread.php?t=381600
yes i tried it didnt work
i tried to hard reset too
the installing of the original rom is the only one can be started and will stop in the middle to give me an error
Hhmmmm
mdrcute said:
yes i tried it didnt work
i tried to hard reset too
the installing of the original rom is the only one can be started and will stop in the middle to give me an error
Click to expand...
Click to collapse
how did you uninstall hard spl in first place...
by putting back original spl
What error you get when you hard spl?
it stays on 0% and never move then it asks me to make a recover
1. Unlock your polaris
2. Than Hard-spl your device
PS: Only use the hard spl in the link provided. Disable your antivirus before procedure.
this might work.
thanks at first
but the first link cant be downloaded
and i think it is just an earlier version of hard spl 2.0
so i think it wont be usefull
From what I've read on a while ago on XDA, if your rom flash progress hangs in the middle of the process, it may be because of the fact that your current radio is too new for your 'old', original rom. You should try to flash an earlier radio before you flash the complete original (6.0?) rom.
And if you get it flash half of your rom, you probably didn't remove HardSPL, but correct me if I'm wrong, I'm not that familiar with it.
pola100
spl-1.25.0000
cpld-2
this is on my boot loader or whatever you call it
ok here it is what i need:
I just need to know the how to down grade my radio if i have no windows working in my pda and no hard spl
could any one help me???
mdrcute said:
pola100
spl-1.25.0000
cpld-2
this is on my boot loader or whatever you call it
ok here it is what i need:
I just need to know the how to down grade my radio if i have no windows working in my pda and no hard spl
could any one help me???
Click to expand...
Click to collapse
As I recall, the figures above indicate that you do have the original SPL. You should try to flash an original rom (if you don't have one, i have a dutch one here (wm6.0). If that doesn't work you should try to flash hardspl (hold the camera button while softresetting to enter bootloader) ( http://forum.xda-developers.com/showthread.php?t=351964 ) and then try to flash a newer rom.
Where are you from?
Btw. I forgot to tell you that you need to flash an old radio too if you're going to flash the original rom. (if you don't have one already).
And when you have hardspl on your device, it'd be wise to flash a rom which include a radio.
I'll be away for a couple of hours, so I've put the original (dutch WM6.0) rom (incl. the original spl, but I think (dont know for sure) you need hardspl2.0 just to flash anything.) online here, let me know if your figured it out.
well thank you for all the help
but i am sadly informing it didnt work if the problem is the radio the i just need to flash another one .
it is just i cant or i dont know the right method to flash the necessary radio
would any one please tell how to flash radio from the boot loader when i dont have hard spl
Maybe a stupid question, but why can't you flash hardspl2? And do you have an unlocked device? You don't live in the Netherlands by any chance right?
why I can't flash hard spl 2 ?
actually I don't know
maybe because I am stuck in the boot loader
and sadly I am living in Saudi Arabia so we don't have much programmers around here nor people who have PDA
that's why I can't find someone to help
Can you describe exactly what you do step by step on your pc and pda and how your hardware is connected?
update: and tell me what messages are on your screen and if you get any errors
well first i connect usb so the pda directly starts boot loader (the screen with three colours)
after that whatever (ROMUpdateUtility.exe) i use the installing stops to give me this messege:
the rom update utility has encountered communication errors during the update process . the program will guide you step by step to recover from the errors so you can continue with the update.
this happens with every rom i tried including the har spl exept for the original rom it advance untill 38% then stops and give me the same messege.
if i try the (step by step ) process it ends up the same way .
anyway what i understand that my problem will end once i put (hard spl)
or if flashed another radio all i need to know is how to do either of them from the boot loader.
i have been so needy but sorry for that i am just sad about my pda i like it alot
I dont think it changes anything, but you do keep the camera button pressed while softresetting your device to get into the bootloader?
Usually your device only gets to the bootloader when you do that, but i can imagine that when your rom update failed and the device cannot boot a rom, it stays in the bootloader, but not in flash mode? Worth a try..
Tell me what appear in your PDA screen during boot. I want to know the information on the first screen like below:
R:
G:
D:
These information usually appear on the right bottom corner or your screen when you boot your device.

HTC P3300 stuck in boot screen

hi.
i got this p3300 and it doesnt fully turn on.After i press power in remains stuck on the boot screen : the one with the HTC logo and info about the rom:
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 1.12.0.0
I tried to flash rom but it fails at 2 or 3% saying image file corruputed which i think its right because i dont think it was unlocked so you can write any rom you want.
I also tried USPL but that i get "NO devive connected" so i cant unlocked my device to write a proper rom into it.
I did all the above with the device in boot mode (record button+reset).
Any ideea?Pls help.
Thank you!
?
tried flashing with HTC_1.12.405.01_026790_WWE_SHIP says invalid model...
T-Mobile dead loop ?
I have similar problem with my artemis. I have a HTC P3300 from T-Mobile. It started with switching itself out, then it didn't want to boot, then it began to hang on bootscreen and at the moment i cannot start it at all (even the battery is fully charged and it is pluggen in my PC).
I suspect that T-mobile build in a dead loop somewhere in the software or hardware. It looks very suspicious to me that both mdas i had from T-Mobile start to make problems exactly a month or or two after the warranty is expired. and the problems develop in the same way in deteriorating manner.
It could be that the hardware cannot take it anymore and it starts to deteriorate exactly after the second year (handy for two years contracts).
Does anyone similar experiences or anyone solved that problem.
Sorry mates I cannot provide you with any info about my PPC (radio, rom version etc.) because I simply cannot get so far to be able to see that information.
Looking forward hearing from you
Cheerz
Hi, my problem is similar, but I need the ROM in ITAlian.
Information about my cellphone:
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 1.12.0.0
Any ideea how to download this ROM? Pls help.
Thanks, Fernando.
Here the same...any one help?
kappp13 said:
hi.
i got this p3300 and it doesnt fully turn on.After i press power in remains stuck on the boot screen : the one with the HTC logo and info about the rom:
IPL 1.12.0001
SPL 1.12.0000
GSM 02.67.90
OS 1.12.0.0
I tried to flash rom but it fails at 2 or 3% saying image file corruputed which i think its right because i dont think it was unlocked so you can write any rom you want.
I also tried USPL but that i get "NO devive connected" so i cant unlocked my device to write a proper rom into it.
I did all the above with the device in boot mode (record button+reset).
Any ideea?Pls help.
Thank you!
Click to expand...
Click to collapse
Have you tried the CMON USPL? It's on Shady's ROM (the lite one) run this first! Be in Bootloader. Hold the Record Key (left key) and by holding that press Power key to switch on! Then try to Update your ROM

Categories

Resources