Which Radio ROM? - Touch Cruise ROM Development

Which Radio ROM is the latest? And where can we get it?
THanks!

ulischultz said:
Which Radio ROM is the latest? And where can we get it?
THanks!
Click to expand...
Click to collapse
lates is this one v 1.58.25.14:
http://www.killou.net/mobile/cruise/Radio_1.58.25.14.zip

Mahmood said:
lates is this one v 1.58.25.14:
http://www.killou.net/mobile/cruise/Radio_1.58.25.14.zip
Click to expand...
Click to collapse
I have tried this but I cant get it to flash. I am already SPL'd. It goes into bootloader ok, then waits forever till it gives up and says connection error. I also tried disconnecting/reconnecting the usb cable when in bootloader (like the SPL procedure) to no avail. Any ideas?

How can i see which radio ROM is on my device pls ?

underzone said:
I have tried this but I cant get it to flash. I am already SPL'd. It goes into bootloader ok, then waits forever till it gives up and says connection error. I also tried disconnecting/reconnecting the usb cable when in bootloader (like the SPL procedure) to no avail. Any ideas?
Click to expand...
Click to collapse
Don't know if it can help but try with this package. It run on my TC.

geezar said:
How can i see which radio ROM is on my device pls ?
Click to expand...
Click to collapse
go to Start ==> Settings ==> Device Information

Try this - the update utility did not work. - Upload failed but I will try again
Don't panic stays on 99% for a little while
Check your radio start>settings>system>device information
hope this helps someone

nc35 said:
Try this - the update utility did not work. - Upload failed but I will try again
Don't panic stays on 99% for a little while
Check your radio start>settings>system>device information
hope this helps someone
Click to expand...
Click to collapse
I've forget a (important) detail. You've to manually put your device in bootloader mode (by pressing the camera button and push and do a soft reset).
As soon as you see the colored bootloader image, release the stylus from the soft reset hole. then release the camera button. Your device will stay in bootloader mode.
Run the ROMUpdateutility.exe (of course, your device must be connected to your PC ;-) )

underzone said:
I have tried this but I cant get it to flash. I am already SPL'd. It goes into bootloader ok, then waits forever till it gives up and says connection error. I also tried disconnecting/reconnecting the usb cable when in bootloader (like the SPL procedure) to no avail. Any ideas?
Click to expand...
Click to collapse
Put your device into bootloader mode first, then double click on the exe.

Rapidshare
http://rapidshare.com/files/95057124/Radio_1.58.25.14.html
Don't forget this will update your device so backup first pls

academic said:
I've forget a (important) detail. You've to manually put your device in bootloader mode (by pressing the camera button and push and do a soft reset).
As soon as you see the colored bootloader image, release the stylus from the soft reset hole. then release the camera button. Your device will stay in bootloader mode.
Run the ROMUpdateutility.exe (of course, your device must be connected to your PC ;-) )
Click to expand...
Click to collapse
This has worked fine... thanks matey

Yes well, I didn't put mine into bootloader mode first (cause I did it before this thread said to do that) and it failed at 99% and went though the HTC recovery instructions! Thankfully though it went through the 2nd time having launched from the bootloader.
Everything is working fine... any chance that something has got screwed up though?

Hi,
Can I have some infos on this new rom ?
What are the changes ?
Thx

Did the radio change will effect also my ROM ?
I want my rom to be left unchanged.
Also, what are the advantadges of this radio version ?

mattan said:
Did the radio change will effect also my ROM ?
I want my rom to be left unchanged.
Also, what are the advantadges of this radio version ?
Click to expand...
Click to collapse
1) Radio and O/S ROM's here may be flashed separately, so flashing this radio will not affect your current operating ROM, just update your radio ROM
2) I've just upgraded to radio 1.58.21.54 from 1.58.21.23. Everything works OK, I feel the WLAN is more efficient but too early to say what real differences may be
3) Instead of Async, I just use a FAT32 1Gb card with the *.nbh file on it with device in Bootloader mode

Is there any soulution to remove "Test Only Not For Sale" (Radio: 1.58.25.14), when the device starting?

ianl8888 said:
1) Radio and O/S ROM's here may be flashed separately, so flashing this radio will not affect your current operating ROM, just update your radio ROM
2) I've just upgraded to radio 1.58.21.54 from 1.58.21.23. Everything works OK, I feel the WLAN is more efficient but too early to say what real differences may be
3) Instead of Async, I just use a FAT32 1Gb card with the *.nbh file on it with device in Bootloader mode
Click to expand...
Click to collapse
Another question: Can I use SpbBackup to restore all my data after the radio update ? I know that I can't do it with rom update, but what about radio update ?

i don't know about using backup software, but i performed the radio update today, and none of the installed programs and my configuration was changed. everything worked as if nothing was done at all.

cortezzi said:
i don't know about using backup software, but i performed the radio update today, and none of the installed programs and my configuration was changed. everything worked as if nothing was done at all.
Click to expand...
Click to collapse
Thanks.
So I don't have to run HSPL, just enter bootloader mode ?

mattan said:
Thanks.
So I don't have to run HSPL, just enter bootloader mode ?
Click to expand...
Click to collapse
1) I hope you have first flashed Olipro's HardSPL version2 (only needed once but first) !! Then you can update/regress ROM's as you wish
2) Using Spb Backup after ROM flashing (either radio or O/S) works ok. It does not backup the actual ROM, but rather the directories in root, registry, PIM databases etc ... this backup is something I do after major changes like ROM upgrades anyway

Related

Radio Problem !!!

--------------------------------------------------------------------------------
Hello,
i am having a frustrating problrems with my p3600
- the phone is not working ! it show that there is no singal and i can't get to the phone seetings
- i tried hard reset / soft reset / upgraded to wm6 , no difference
- tried to flash the radio , but it stops at 0% , and after one hour , it is still 0%?
please help!
Try updating to WM6 with this package:
Apoc said:
jesus, use this: http://rapidshare.com/files/2987211...y_WM6_v2.0.0.4_incl_HSPL___Radio1.41.0.11.exe
created a self-extracting archive so that you only need windows to do the upgrade(no 7zip or winrar), it should extract to a temporary folder and execute the updater, it will flash the hardspl, radio 1.41.0.11, and lsvw's 2.0.0.4.
Click to expand...
Click to collapse
Like it says, it's a total upgrade package which will also upgrade the radio, using harspl, so CID shouldn't be a problem...
Just connect to ActiveSync (preferably as a guest) and start the .exe you've just downloaded. It'll push SSPL by Des (modified bootloader) to the phone, execute it and start updating.
Let me know if this worked...
Did the upgrade and still not working ......
?
Time for a warranty repair!
Your symptoms stongly suggest a hardware fault with the Qualcomm radio chip.
Updating to the WM6 ROM's doesn't update the Radio, so you could try flashing just a Radio ROM (though by your 1st post you've already tried that?)
The instructions for LSVW and Mun-rus both state that the radio should be updated prior to applying the WM6 ROM itself.
osamanet said:
Did the upgrade and still not working ......
?
Click to expand...
Click to collapse
But did the whole upgrade process finish all well...? Is radio 1.41 installed now?
It's a bummer you still have problems, but just exclaming it's not working doesn't really help... Can you be a bit more specific please???
What went well, and what didn't, and what is the exact problem that has risen or didn't get solved? Did you get any specific error-messages? Are you in a good-coverage area? Etc,etc...
NeilM said:
Updating to the WM6 ROM's doesn't update the Radio....
Click to expand...
Click to collapse
Yes it does....the package i linked before does flash radio 1.41.
Moaske said:
Yes it does....the package i linked before does flash radio 1.41.
Click to expand...
Click to collapse
Ah- missed the significance of that one! Thanks
Problem is that this topic is split in 2 forums, so some info not consistent- his answers in the other thread stongly suggest hardware failure.
Hello,
thank you for answering
i did try all the updates in this forum , SAME PROBLEM !
when i press the green button nothing happins , when i go to Phone nothing happiens , when i go to phone settings , also nothing happiens
it used to work before , but it used to disconnect every hour or two , then it stopped working
is the device coverd by warranty in the U.S ? i bought it from eBay less than three months ago
I've no idea if it is likely to be covered- was it a new device, fully boxed?
If so, there should be an international warranty card inside, but I don't know HTC's policy on coverage in USA.
HTC's USA Home Page doesn't mention this model at all.

I think I bricked my phone...

So I installed the updated ROM and Radio to see if I could get the GPS working...
Everything went fine, I had to call Verizon to get the AKEY, but everything worked after that. Then I decided to downgrade because I thought it was running a little slow, and I didn't like all the added programs.
That was where I messed up. I did everything like I thought I was supposed to. I used the RELOCKER, and flashed the older version of the VZW rom... well atleast I attempted to. My phone is stuck at 0% flashed.
Any ideas?
ajshah said:
So I installed the updated ROM and Radio to see if I could get the GPS working...
Everything went fine, I had to call Verizon to get the AKEY, but everything worked after that. Then I decided to downgrade because I thought it was running a little slow, and I didn't like all the added programs.
That was where I messed up. I did everything like I thought I was supposed to. I used the RELOCKER, and flashed the older version of the VZW rom... well atleast I attempted to. My phone is stuck at 0% flashed.
Any ideas?
Click to expand...
Click to collapse
It is really tough to brick a phone.
Just pull the battery and wait 3s. Then replace. It should boot back up to the last ROM installed.
The only problem with that is that it doesn't... its stuck on the bootloader screen...
ajshah said:
The only problem with that is that it doesn't... its stuck on the bootloader screen...
Click to expand...
Click to collapse
1) To get the Tricolor Bootloader Screen to come up (actually this may be where you are already - if so, skip to #2). You must simultaneously: (a) hold down the power button; (b) hold down the camera button; and (c) use your stylus to press the little reset button in the hole at the bottom of your 6800. This should pop up the Tricolor Bootloader screen if you'd installed this first, as instructed.
(2) Then plug it into the computer's USB port. Make sure that USB is NOT enabled in "Windows Mobile Device Center" (should be in your start->programs menu). Click on connection settings and turn off the checkbox for USB connection.
(3) Then run the 3.17 Rom loader. This will get you back up and running.
(4) Then start again and run the 2.09 or 2.17 Rom loader. It should load without a hitch.
(5) Then you will have to re-setup your your MSID and MDN. You will need your EPT.
3.17 Rom Loader? which one is that?
I know I am asking a lot, but I have been searching all day, and I am a relative n00b...
so Thank you soo much for helping me out...
I have the same problem as you. Relocked the phone and now I can't do anything. Tried flashing to different radios, different roms and nothing. I did get 1 rom to go to 1% complete but it told me I had the wrong vender(sic) or something
ajshah said:
3.17 Rom Loader? which one is that?
I know I am asking a lot, but I have been searching all day, and I am a relative n00b...
so Thank you soo much for helping me out...
Click to expand...
Click to collapse
Hmm -- well maybe I need more info.
Which ROM did you 'upgrade' to?
I upgraded to the new one with GPS... I did everything in the steps, the way it said to do it...
Then I wanted to downgrade, and I saw how some1 else did it with relocking it and downgrading it, so now my bootloader reads:
TITA100
SPL-1.06.0000
CPLD-9
and it still says RUUNBH in the right corner...
Oh, and the SD card TITAIMG.nbh thing doesn't work either, unless I am doing it wrong...
The error I get is a 262 error, if that helps...
ajshah said:
I upgraded to the new one with GPS... I did everything in the steps, the way it said to do it...
Then I wanted to downgrade, and I saw how some1 else did it with relocking it and downgrading it, so now my bootloader reads:
TITA100
SPL-1.06.0000
CPLD-9
and it still says RUUNBH in the right corner...
Click to expand...
Click to collapse
Oh -- then just run the Official Released version of 2.17. You should be golden.
quantumforce1 said:
Oh -- then just run the Official Released version of 2.17. You should be golden.
Click to expand...
Click to collapse
Where can I find the official version?
do i need to go through all of this if i want to go back from the gps rom to the dcd kitchen/rom 2.0 or can i just flash back and you only have to relock if you want to go back to the stock rom?
friguy33 said:
do i need to go through all of this if i want to go back from the gps rom to the dcd kitchen/rom 2.0 or can i just flash back and you only have to relock if you want to go back to the stock rom?
Click to expand...
Click to collapse
I reflashed back to the 2.0 rom and I got stuck at the vzw logo screen so I tried to get the radio flashed back. I ended up trying to lock the spl and thats where i got screwed
quantumforce1 said:
Oh -- then just run the Official Released version of 2.17. You should be golden.
Click to expand...
Click to collapse
Tried that... Didn't work... I tried re-installing radio 1.40 first and then 2.17 and nothing, then i tried the other way... I still am stuck at 0% and then I get the 262 error...
friguy33 said:
do i need to go through all of this if i want to go back from the gps rom to the dcd kitchen/rom 2.0 or can i just flash back and you only have to relock if you want to go back to the stock rom?
Click to expand...
Click to collapse
Think of it this way ...
There are 'basically' three parts to the software that runs your phone.
1. There is the SPL / bootloader.
2. There is the Radio ROM.
3. There is the System ROM.
2 and 3 above will not load or work correctly if #1 above is bad or the wrong version.
Therefore, if you want to go back to 2.17 then the easiest way to do this is to:
1a. Get the ReLocker (which is SPL v1.06)
1b. *Don't worry that it stays in the boot loader mode.
2. Run your offical carriers released ROM, Sprint 2.17 (which will include both the System and Radio ROMs).
3. Reload your custom apps.
4. Sync.
5. *Remember from the previous article above, you will still need your EPST, MDN and MSID codes.
That's it.
If I reset, right before I get the tri color screen, it flashed a grey screen that says "no image file" for a second.
dagnasty said:
If I reset, right before I get the tri color screen, it flashed a grey screen that says "no image file" for a second.
Click to expand...
Click to collapse
Do you have the tri-color screen up? If so - what version?
Screen says:
TITA100
SPL-1.06.0000
CPLD-9
dagnasty said:
Screen says:
TITA100
SPL-1.06.0000
CPLD-9
Click to expand...
Click to collapse
Mine says the same ****....
Does yours flash "no image file" right before you get the tricolor screen?

[Need Help]ROMs won't boot after initial setup

I hope someone here can help me to make my LEO work again.
Im having huge problems with my HD2 after flashing a ROM with Extendir. While setting up the device with Preset Installer my PDA went to deep sleep and failed installing all cabs.
After reboot it hung on the screen where Radio Version etc. is shown. That is why i made another Hard Reset. That let my phone boot again but after initial setup it hangs again at that place.
I tried another ROM and experienced the same problem. After that i went back to shiped with spl and radio. Not even that fixed the problem.
I tried MTTY with task 29 and reflash stock. It stays the same! After initial setup my phone sometimes hangs before or after boot animation. sometimes it boots till sense is started and hangs there.
Does anyone have a smart idea how i can make my leo run propper again?
Thanks for help.
edit: im not sure if its Extendir. It could be something else, too. I tried flashing via usb and storage card.
Ultimaex said:
I hope someone here can help me to make my LEO work again.
Im having huge problems with my HD2 after flashing a ROM with Extendir. While setting up the device with Preset Installer my PDA went to deep sleep and failed installing all cabs.
After reboot it hung on the screen where Radio Version etc. is shown. That is why i made another Hard Reset. That let my phone boot again but after initial setup it hangs again at that place.
I tried another ROM and experienced the same problem. After that i went back to shiped with spl and radio. Not even that fixed the problem.
I tried MTTY with task 29 and reflash stock. It stays the same! After initial setup my phone sometimes hangs before or after boot animation. sometimes it boots till sense is started and hangs there.
Does anyone have a smart idea how i can make my leo run propper again?
Thanks for help.
edit: im not sure if its Extendir. It could be something else, too. I tried flashing via usb and storage card.
Click to expand...
Click to collapse
to specify that rom you used in this moment and to specify that RADIo is used
I used the Lost in Asia Regular Version V0.8 and Radio 2.08.50.05 and HSPL.
At the moment i have a lover Radio version.
Ultimaex said:
I used the Lost in Asia Regular Version V0.8 and Radio 2.08.50.05 and HSPL.
At the moment i have a lover Radio version.
Click to expand...
Click to collapse
to assess that rom V.0.8 it has rom 2.0x base
radio 2,08 to enable 576 MB
the rom that it uses, it could not be compatible with the version radius
try to chnge a version radio or try to change version rom
if you use radio 2.08 from rom 2.07,try to flash rom cooked with 576 Mb enable
sorry for my poor english,i'm Italian
Sorry mate
the problem is other
I have since the rom of bob qualified V.08 is for 576 mb
You tried booting up with the SD card taken out of the device?
WB
You need to have a radio that supports the 576 mb. But I don't think this is your problem. It sound like to me your storage card is the problem. If you have another storage card format it to FAT 32 and try again. I bet your problem is solved. Also Don't use a 16gb card until you know for sure it is working. Even then there are problem with some people using them.
I dont have a Storage Card inserted now. Still the same problem
Btw. Using Laurentius V1.2 now. Same error here. i try to flash a lower Radio now.
As i said before i flashed stock 1.66 via storage card with radio and spl and still had the same Problem.
Ultimaex said:
I dont have a Storage Card inserted now. Still the same problem
Btw. Using Laurentius V1.2 now. Same error here. i try to flash a lower Radio now.
As i said before i flashed stock 1.66 via storage card with radio and spl and still had the same Problem.
Click to expand...
Click to collapse
have you try flash rom with activeSync???
Are you able to flash HSPL again? Can you confirm on the Tri Color screen it says HSPL 1.42?
bobsbbq said:
Are you able to flash HSPL again? Can you confirm on the Tri Color screen it says HSPL 1.42?
Click to expand...
Click to collapse
Everything flashes as usual. HSPL, Radio and ROMs. The software just isnt running stable after flash.
If it would be a Radio/SPL/ROM problem the stock rom should fix it.
Not wanting to be the one to say it but maybe your device is defective or damaged. Or maybe the problem was caused ny the failure going to sleep, but I don't think so. I have accidentally unplugged mine before during flash and still got it back. If you reflash the ROM it should work again. If you don't have any luck I would flash back to the Stock ROM and take it in for repair.
To bad noone can help. I will do some research and if i have no success i will send it back.
Some weeks of waiting
bobsbbq said:
Also Don't use a 16gb card until you know for sure it is working. Even then there are problem with some people using them.
Click to expand...
Click to collapse
Any sources for that?
I never read anything backing this up.
pathologo said:
Any sources for that?
I never read anything backing this up.
Click to expand...
Click to collapse
Yes there have been many. There have been some in my threads. There is also a thread posted here with lots of discussions and it was determined the the lock ups and freezes with Manila 19222911 was the 16gb cards. It seems there was only one ROM that did not have the problem and unfortunately this cook doesn't share with others.
im making improvements. after flashing stock i found out that i can change more and more settings and install programs without the need to hard reset. when i damage the filesystem with a program or setting i hardreset the device. after restart i can install that program without problems and can try another one.
seems that my device is repairing magically
Ultimaex said:
im making improvements. after flashing stock i found out that i can change more and more settings and install programs without the need to hard reset. when i damage the filesystem with a program or setting i hardreset the device. after restart i can install that program without problems and can try another one.
seems that my device is repairing magically
Click to expand...
Click to collapse
So the stock ROM is working then.
Ultimaex said:
im making improvements. after flashing stock i found out that i can change more and more settings and install programs without the need to hard reset. when i damage the filesystem with a program or setting i hardreset the device. after restart i can install that program without problems and can try another one.
seems that my device is repairing magically
Click to expand...
Click to collapse
try using the energy Rom...it works for me...all i can say, it's more stable than any other roms that i use before....
bobsbbq said:
So the stock ROM is working then.
Click to expand...
Click to collapse
I think you didn't understand. after EACH program or setting i need to hardreset.
after hardreset i can install that program as usual as all programs i did that with before.
sseems that i 'gain' more and more storage back.
Ultimaex said:
I think you didn't understand. after EACH program or setting i need to hardreset.
after hardreset i can install that program as usual as all programs i did that with before.
sseems that i 'gain' more and more storage back.
Click to expand...
Click to collapse
I guess I don't understand. You have to have a working ROM to install a program? For a stock ROM you should not have to install anything. It either works or it doesn't.

Problem Flashing ROM

Hi, I have just flashed my handset with: RUU_Leo_Dopod_CHS_1.70.706.0_Radio_CRC_Signed_15.3 2.50.07U_2.07.51.22_2_Ship.exe
I now get the message 'your OS ROM isn't customized for your hardware.
Please reflash the proper ROM Code or contact the service centre.'
I'm trying to reflash RUU_Leo_HTC_WWE_1.66.405.2_Radio_Signed_15.30.50.0 ΒΆ
7U_2.06.51.07_Ship.exe, but it fails to communicate with the device.
Any ideas how I can fix this?
Thanks
Try downloading the relevant radio version from this link (note that download only contains the .nbh file):
http://forum.xda-developers.com/showthread.php?t=611787
Then download the CustomRUU.exe file from here:
http://forum.xda-developers.com/showpost.php?p=4798017&postcount=1
Put both files in the same folder and run the CustomRUU.exe file and it should hopefully work.
Mastoid said:
Try downloading the relevant radio version from this link (note that download only contains the .nbh file):
Then download the CustomRUU.exe file from here:
Put both files in the same folder and run the CustomRUU.exe file and it should hopefully work.
Click to expand...
Click to collapse
Okay, tried that and it's exactly the same - gets to the stage 'verifying data on your pda' then gets connection error as it hasn't been able to connect through mobile device centre
blue sabre said:
Okay, tried that and it's exactly the same - gets to the stage 'verifying data on your pda' then gets connection error as it hasn't been able to connect through mobile device centre
Click to expand...
Click to collapse
Did you try this?
Go to Start > Settings > Connections > USB to PC > Uncheck "Enable advanced network functionality"
Mastoid said:
Did you try this?
Go to Start > Settings > Connections > USB to PC > Uncheck "Enable advanced network functionality"
Click to expand...
Click to collapse
I'm not able to get into any menus - I just have a black screen with the above error message in red text.
blue sabre said:
I'm not able to get into any menus - I just have a black screen with the above error message in red text.
Click to expand...
Click to collapse
Have you checked your HSPL version? there must be SPL 1.42.0000 on your device otherwise the installation will fail.
To check your SPL version, hold the Volume Down button and do a reset. It is possible to downgrade to this SPL, by just flashing to an Official ROM with this SPL version.
Mastoid said:
Have you checked your HSPL version? there must be SPL 1.42.0000 on your device otherwise the installation will fail.
To check your SPL version, hold the Volume Down button and do a reset. It is possible to downgrade to this SPL, by just flashing to an Official ROM with this SPL version.
Click to expand...
Click to collapse
Well I had hspl on there from this site. I was changing ROMS this morning as I wasn't massively impressed with the custom one I flashed it with. It wont let me flash with any ROM as the Update Utility Cannot connect to the phone.
blue sabre said:
Well I had hspl on there from this site. I was changing ROMS this morning as I wasn't massively impressed with the custom one I flashed it with. It wont let me flash with any ROM as the Update Utility Cannot connect to the phone.
Click to expand...
Click to collapse
Try take the battery out for about 2 minutes and then power it back on.
From the troubleshooting notes section found via this link, it stated the following:
"Your OS ROM isn't customized for your hardware. Please reflash the proper ROM code or contact the service center", !!! Problem NOT related to HSPL !!! ... this means that you flashed a region protected rom... flash any other rom that has your region ID... or patch it
Mastoid said:
Try take the battery out for about 2 minutes and then power it back on.
Click to expand...
Click to collapse
Had no joy with that either! Will try to flash from SD Card- hopefully that'll do it!
As far as I understand the issue, it is not the ROMs that are region protected, so that is not what is causing the problem. I believe the problem is that some phones (like yours) have encoded firmware that possibly restricts the type of ROMs that can be installed? So, some people can only install ROMs that are designed for their region.
Flashing from SD Card seems to be doing the trick nicely. Phew.
blue sabre said:
Flashing from SD Card seems to be doing the trick nicely. Phew.
Click to expand...
Click to collapse
I am also relieved lol.
Btw, where are you from?

HTS HD2 - Cooked ROM Bricked

I tried to cook my own ROM and when I installed, the installation was successful. But after that my phone does not start. when I click the power button, the phone does not boot.
My ROM size was close to 300 MB.
Any help is appreciated.
mukesh_thiru said:
I tried to cook my own ROM and when I installed, the installation was successful. But after that my phone does not start. when I click the power button, the phone does not boot.
My ROM size was close to 300 MB.
Any help is appreciated.
Click to expand...
Click to collapse
Phone doesn't boot? What do you mean doesn't do anything or gets stuck?
If your device turns on you could try to get in bootloader by holding volume down when turning on the device. If that works you can connect to usb and flash another rom
When I hit the power button nothing happens, the screen is black, the device does not start. No bootloader, no led light nothing, I tried hard reset, I tried the reset button.
When I was installing the custom ROM the battery was full. When I connect to USB, the computer says some Qualcomm device thats it.
If you cant boot in bootloader, then its screwed. But you said your pc sees it as qualcom device...so it probably ok.
Just put it in bootloader, and flash a stock ROM.
PC shows as "qualcomm cdma technologies msm". But nothing else not going to bootloader
Did your ROM had a radio in it or only the OS?
I guess only OS, I think I did not have Radio
Did you tried to leave the battery?
Which Original stock rom did you used for cooking your own? Have you a link?
Did you already searched in forum for a possible fix?
i found some links http://www.google.com/cse?cx=partne...mqefhnf&ie=ISO-8859-1&q=hd2+bricked&sa=Search
Give us as more infoes as you can.
HD2: Tmous or Htc brand?
HDSPL? Have you installed one?
It a tmobile. I used the Oskitchen and downloaded a stock ROM to start. I removed some of the items that I did not want, then after I did "start building". I took the "RUU_Signed_0409" from the output folder. I flashed this to my device.
HDSPL - http://forum.xda-developers.com/showthread.php?t=611433 I followed this tutorial.
Can you please let me know what you mean by "Did you tried to leave the battery?"
Leave the battery means Take out the battery for some times and then return it inside.
Did you dump a TMOUS Stock rom, right?
mukesh_thiru said:
It a tmobile. I used the Oskitchen and downloaded a stock ROM to start. I removed some of the items that I did not want, then after I did "start building". I took the "RUU_Signed_0409" from the output folder. I flashed this to my device.
HDSPL - http://forum.xda-developers.com/showthread.php?t=611433 I followed this tutorial.
Can you please let me know what you mean by "Did you tried to leave the battery?"
Click to expand...
Click to collapse
Yes tmobile stock ROM
mukesh_thiru said:
It a tmobile. I used the Oskitchen and downloaded a stock ROM to start. I removed some of the items that I did not want, then after I did "start building". I took the "RUU_Signed_0409" from the output folder. I flashed this to my device.
HDSPL - http://forum.xda-developers.com/showthread.php?t=611433 I followed this tutorial.
Can you please let me know what you mean by "Did you tried to leave the battery?"
Click to expand...
Click to collapse
Can you please compress the ROM and upload it somewhere so we can take a look? If you didn't select splash screen or radio the ROM should contain only the OS section and therefore be safe to flash.
MOD EDIT: removed link because not safe,PM OP for link. thanks.
@ Airxtreme:
Did you see his prvious post? See below, he hisnt totaly sure by Radio.
Most TMOUS mobiles Rom upgrade failure are due to flash a non compatible RADIO , its not safe to flash the rom linked.
Im removing the link, if someone wanna try what Airxtreme suggested, please share it by PM....sorry but i do not want some noobs complaining for his phone bricked.
mukesh_thiru said:
I guess only OS, I think I did not have Radio
Click to expand...
Click to collapse
airxtreme said:
Can you please compress the ROM and upload it somewhere so we can take a look? If you didn't select splash screen or radio the ROM should contain only the OS section and therefore be safe to flash.
Click to expand...
Click to collapse
mukesh_thiru said:
MOD EDIT: removed link because not safe,PM OP for link. thanks.
Click to expand...
Click to collapse
Sorry but the archive seems to be corrupted however from the part I could extract it looks like the ROM file except for the fact that it's 400mb big (but it shouldn't be a problem if yours is a TMOUS phone) has only the OS section and that means it should have been safe to flash. Try removing the battery as suggested, unless you have issues with your computer's USB or some other application messing up the RUU updater the phone shouldn't have been permanently bricked also when you turn it on to enter the bootloader mode try doing it with the phone not connected to the computer maybe it just doesn't like the USB port.
af974 said:
@ Airxtreme:
Did you see his prvious post? See below, he hisnt totaly sure by Radio.
Most TMOUS mobiles Rom upgrade failure are due to flash a non compatible RADIO , its not safe to flash the rom linked.
Im removing the link, if someone wanna try what Airxtreme suggested, please share it by PM....sorry but i do not want some noobs complaining for his phone bricked.
Click to expand...
Click to collapse
From what I saw there is no radio in there and the archive wouldn't even extract so I don't think there is any risk about somebody flashing that file.
Yeah i see that it is corrupted, but you know ....i have seen some recent post in Kaiser forum with people with Different phones then the Kaiser, asking in Spl thread how to install it on their phone....so better dont risk imo
airxtreme said:
From what I saw there is no radio in there and the archive wouldn't even extract so I don't think there is any risk about somebody flashing that file.
Click to expand...
Click to collapse

Categories

Resources