I updated the rom to this folowing this thread
NEW ROM: RUU-Prophet-AKU2.2-2.20-2.47.21-Jester-r1 and can be seen on this link. http://forum.xda-developers.com/showthread.php?t=284578
but after running the programm and doing a hard reset appears the black screen where it says"
Code:
Press SEND to restore factory defaults, or other key to quit.
then a pressed SEND and appears this "FORMAT FAT something" and then "FORMAT INVALID" and just appears the bootloader screen and two lines.
one with the IPL
and the other with the SPL
but none information about the GSM or OS
I've tried reinstaling the official rom from Imate site, but the appears this message
Code:
"ERROR [326]: The NBF file cannot be used for your pda phone please check your NBF file."
I hope you can help me. Thanks for your support.
Did you use the right ROM for your device? G3 or G4?
On the bootloader screen there are these:
IPL 1.00
SPL 2.20.0001
So, if I'm not wrong my device is a G4, right?
I hope I didn't screw up.
Thanks for your attention.
I'm not an expert, but it definitely looks like you flashed it with a G4 ROM.
I hope that your SPL ended with 0001 also before the upgrade. Otherwise you flashed a G3 chip with a G4 ROM.
So, what can I do If I flashed a G3 chip witha G4 rom, is there anything to do?
arg0 said:
I'm not an expert, but it definitely looks like you flashed it with a G4 ROM.
I hope that your SPL ended with 0001 also before the upgrade. Otherwise you flashed a G3 chip with a G4 ROM.
Click to expand...
Click to collapse
you are right, try the gold card, it is the only slution known for now, I did post the offset for the spl.nbf file, and the spl.nbf file using l command, but jezters tells that didn't work???? but I think it should work
check the whole threads please http://forum.xda-developers.com/showthread.php?t=285346 and this http://forum.xda-developers.com/showthread.php?p=1336250#post1336250
HI,
Thanks for POF and other forum members.
I upgraded my DOPOD C800 with WM6. Used POF HARD-SPL and Official HTC P4350 ROM.
Thanks
Jose
Can you mention the ipl and spl of your c800 before you had gone about with Hard-spl?
murali509 said:
Can you mention the ipl and spl of your c800 before you had gone about with Hard-spl?
Click to expand...
Click to collapse
Hi mine is- before upgrade
SPL 1.09.0001
IPL 1.09.0001
ROM 1.7.707.3 WWE
ROM Date 11/01/06
Radio 2.69.90
protocol 4.1.13.30
Ext rom 1.7.707.106
OS 1.7.0.0
I also have a Dopod C800 with the same ipl & spl. Can you direct me to the POF Hard-Spl files that you used? I have the HTC P4350 WWE WM6 RUU. Any help is greatly appreciated...scared to death I'll brick the phone!
How i upgraded My DOPOD C800
STEP I:
Download the following files
1) USPL --- Flah centre.rar file from
http://www.mediafire.com/?axtm5qlmbli
2) Official RUU -HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe
3) Make sure ur computer is always power on...not hibernated
Step II:
1) Create 2 folders eg:flash and rom.
2) Extract flash centre.rar in flash folder
3) Extract HTC_P4350.... ship.exe in rom folder .
( Use winrar or simply double click the file. It will start the upgrade window ,click next, then hold.Go to the temp folder, u will find all the extracted content there.Copy all the content to the new rom folder. After that cancel the upgrade window.)
4)After extracting the content in the rom folder ,*****delete the SPL.nbh file ****
Step III:
Connect your phone to the computer, make sure activesync is enabled (green icon)
Step IV
1)Open the flash folder --- follow the read me file in this folder
ie
2)Run herald-uspl.exe on your computer and follow the instructions on screen.
- it will run in command window and ask u to enter the values..follow the screen
After 2/3 steps if will ask u to chk the device-- the activesync green icon in ur computer will become grey and the screen of ur mobile will be blank-white.
!!! now u have sucessfully hard spl ur device!!!
**** dont touch or remove the connection or close any program****
3)After this it will start the RUU program ,follow the instruction ,click update ( u wont find any previous ROM installed),it may or will show ERROR [240] : FILE OPEN
clik finish/cancel and exit **this program only**.
4)Now without removing anything open the rom folder and clik the ROMUpdateUtility.exe file and follow the instruction.
thats it. ur mobile will be upgraded. dont get panic...it will take some time and the mobile will be white in colour.
Thanks
Jose
C800 upgrade success
Upgraded Dopod C800 with same IPL/SPL/RADIO parameters as mjose using his directions and it worked like a charm. Am WM6 with no issues now.
Thanks POF and mjose and everyone else on the forum for your help!
WHen using Herald-USPL - it is NOT permanently HARD-SPL!!!!
Please check the SPL now - and report....
if it doesn´t show 4.70.yang - then it is only USPL = temporarly CIDunlocked= NOT HARD-SPL
thx.
How much free memory did you get by upgrading to official HTC WM6? I got only 25mb free with no extended rom install!
C800 USPL vs Hard SPL
Poppamopps, you are quite correct. The update I performed was NOT Hard-SPL. I would prefer Hard-SPL but my understanding is that it should not be used on a device with IPL/SPL below 4.0. I am 1.9 both IPL/SPL.
Is there now a HARD-SPL that is safe to use on the Dopod C800 that is below 4.0 ?
billy-the-t said:
Poppamopps, you are quite correct. The update I performed was NOT Hard-SPL. I would prefer Hard-SPL but my understanding is that it should not be used on a device with IPL/SPL below 4.0. I am 1.9 both IPL/SPL.
Is there now a HARD-SPL that is safe to use on the Dopod C800 that is below 4.0 ?
Click to expand...
Click to collapse
nope. BUT try USP for falshing an official HTC rom with higher SPL and then HArd-SPL....
NICE! I successfully upgraded my C800 to wm6 using mjose instructions. Thanks to mjose and to all those involved.
Thanks to mjose, UPGRADED
Followed exactly what mjose said. Successfully upgraded. Thanks to everybody
Any idea how to install touch flo now?
C800
ROM: 4.17.405.2 WWE
need help please!
tried updating following mjose's listed method exactly, but failed after the screen went blank, and now my c800 seems to be dead (or bricked?!). can't even power on now. is there any way to revive it, or do i now have an expensive doorstop?
longj49 said:
need help please!
tried updating following mjose's listed method exactly, but failed after the screen went blank, and now my c800 seems to be dead (or bricked?!). can't even power on now. is there any way to revive it, or do i now have an expensive doorstop?
Click to expand...
Click to collapse
managed to do a hard reset but failed to restore, the screen now is green in color and showing:
IPL 1.09.0001
SPL 1.09.0001
then it's stuck there unless i remove the battery.
can anyone help please?
longj49 said:
managed to do a hard reset but failed to restore, the screen now is green in color and showing:
IPL 1.09.0001
SPL 1.09.0001
then it's stuck there unless i remove the battery.
can anyone help please?
Click to expand...
Click to collapse
i'm assuming nobody was awake. when you were posting....but i could be wrong.
i have no idea what a green screen means other than it's green hehe... and have never flashed a dopod.. but i'll pretend it's a herald?
can you put it in bootloader mode????
soft reset(put stylus in the hole)... and hold down the camera button..
you should get the tri-color screen..
mv3 said:
i'm assuming nobody was awake. when you were posting....but i could be wrong.
i have no idea what a green screen means other than it's green hehe... and have never flashed a dopod.. but i'll pretend it's a herald?
can you put it in bootloader mode????
soft reset(put stylus in the hole)... and hold down the camera button..
you should get the tri-color screen..
Click to expand...
Click to collapse
hey thanks! yes. i've got the asian herald. i got into bootloader mode as per your suggestion - is that the one with red/green/blue horizontal bands with a thinner white band at the bottom? ok what should i do next?
i was able to run the ROM Update utility after that, but got an error 300. checked the documentation and found out that i used the wrong version for my phone, which was RUU -HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe. would you know which one i should use?
i'm guessing your phone is not an English phone?
you need to find the native RUU for your phone.. Taiwanese Mandarin> HK Traditional? Japanese?.... if you can find it, then put your phone into bootloader and run the RUU file from your pc.
other than that, I don't know if anyone here has access to asian RUU's
doesn't look good, can't seem to find my region's wm6 rom anywhere. even tried to restore using the original wm5 rom from htc website, but still getting error 300. i think running herald-uspl.exe initially could have somehow caused some corruption.
well, i might have to visit dopod's service center soon.
thanks for your help, mv3, greatly appreciated.
did you try looking for official ruu from asia.htc.com
I suggest you load that before going to the repair centre
ok ive managed to brick my phone...
ive made a goldcard and im pretty sure that everything is correct.
if i have only the goldcard file and heraimg.nbh on my card and insert it it says "checking sd" but then goes to the normal tricolor screen.
so i went and but heradiag.nbh on the card aswell.
it then starts checking but then comes up with the error:
sercurity level not cleared!
can someone help me?!
my ipl and spl is: 1.09.001
all help will be really apreciated!
thanks a lot
pseudo
same problem with me
Same!
Same here!!!
i made a goldcard, using a tutorial i found on here, and i'm positive i did it correct.
But still have a security warning!
Can can't get any further with my device.
I have IPL 4.23.0001
SPL 4.23.0000
I Can boot in OS, but then the OS hangs and can't press any buttons.
the only button i can press is the power off, and they i can choose YES/NO
And that works fine.
But the rest is just FROZEN!!
WHO CAN HELP ME PLEASE??
But it doens't sync in windows, so i can't do a FLASH, No flash can't be done from SD CARD?
THE GOLDCARD has no effect?
So who can help me out?
same prob - no solution until now...
nevermind didnt check the dates, old thread...
but still problems!
Any solution for this problem???????????????????
Hi guys,
my Orbit failed in the middle of a flash (in Windows with RomUpdateUtility).
Now I can only get to the bootloader, nothing else.
I think the CID unlock must have failed somehow, because using the SDcard method I cannot flash any cooked ROM. In fact I cannot flash ANY ROM now! I have tried the default shipped 02 ROM's but they all fail at 5% in RomUpdateUtility.exe thru windows, and also fail via the SDcard method (it sits there forever saying reading SD card).
Any ideas? Any other O2 ROM's I should try? Or can I send it for repair to any one off this forum? Should I bin it, maybe the flash chip is faulty?
IPL 1.25.0001
SPL 1.25.0000
Tried (and failed) ROM list:
HTC_P3300_WWE_3.13.405.1_4.1.13.44_02.94.90_Ship_R.exe
RUU_Artemis_O2_UK_3.4.206.2_4.1.13.28_02.67.90_Ship.exe
HTC P3300_SPA_3.13.412.1_4.1.13.44_02.94.90_Ship_R.exe g
Arteimg.nbh from http://rapidshare.com/files/41614347/OrbitO2UK.rar
art_htcwwe_11240501_026790_wwe_ship from http://www.expansys.com/ft.aspx?k=79618
Vanilla 4.01
Black & Blue 5.0
Thanks for reading, underzone
I have the exact same problem only mine is stuck with IPL 3.04.0001 and SPL 3.04.0000
When i try the original rom (o2 factory) it goes at 4% into Error 226 (something with the Extrom), any other rom wont work since no USPL... damn it.
Any Ideas on this?
Hi
Big problem.
1. CID Unlock - has worked
2. Flashed new ROM - has worked
After 100% the RUU says, Congrats... But too late i saw it was an ELFI ROM with 74MB but my Touch is an ELF 64/128.
But it booted! Once...
After the device has rebooted i made the screen settings and after windows has configured the device rebooted again.
After reboot the device doesnt come back.
I got the boot logo and then the screen will be black.
Hardreset doesnt work.
After FORMAT FAT & FORMAT IS COMPLETED the screen is always black.
Holding CAM Button and Softreset brings the Colored-Display.
IPL 2.24.0002
SPL 1.11.0000
A new CID unlock doesnt work because there is no active sync connection.
Flashing any other ROM works but it seems to have no effect.
RUU can connect but dont shows any installed image version.
If i click update the progressbar in the HTC display appears and goes to 100%.
After finished the update the device reboots and the screen is black.
Did i have erased my htc? Is there any solution for this problem?
*** EDIT ***
I tried this ht*p://forum.xda-developers.com/archive/index.php/t-359413.html
Now i have IPL 1.11.0002 an SPL 1.11.0000
Step G3/7 says:
Download T-Mobile 2.26 rom (ht*p://rapidshare.com/files/38880130/ruu_prodigy_226102_22610105_022511_tmous_wwe_ship. exe.html)and flash it to your device! Done? Go to step G3 / 8
But the link is invalid. (yes ive seen the space at the . exe)
Does anyone have this file so i can try this step.
Ecosys
try upgrading the IPL/SPL to some 2.2X version. and next time post in an appropriate thread related to unbricking, u dont have to start a new thread.