Database Users

Does your Trinity/Dopod drop calls regularly?

My Dopod D810 from 3 drops calls regularly.
I think every single call will drop out after about 1-2 minutes. I also notice that when my phone is 'warm' from charging or other uses, the call can drop as quickly as 10 seconds into the call.
Initially it was suggested that the drop outs were due to my Phone > Band selection being set to 'Auto' but I have since changed this to Network Type=WCDMA and GSM/UMTS band=UMTS(2100+800).
But now I'm more inclined to think it has something to do with the device's temperature....
Any other ideas other than taking it back to 3?

Try changing the Radio ROM.
I had a similar problem after changing my Radio ROM from 1.41.00.11 to 1.46.00.11. Now I`m using 1.46.30.11 version and everything is OK. I even noticed a GPS signal level improvement.

I have the similar problem too. I m with 3 Australia. Upgraded to WM6 official ROM, still observing if call drop still happened.
If not, will take back for warranty repair

I am using a HTC-branded P3600 with the official HTC GPS-enabled WM5 ROM on the Vodafone UK network. With reasonable approximation I can say that I have 0 dropped calls (including calls made or received while in car).
My network type and band selections are both "auto".
Sometimes I make calls while the phone is charging via USB from a laptop (which makes it rather warm) but I haven't noticed any dropped calls in that situation either.

Radashka said:
Try changing the Radio ROM.
I had a similar problem after changing my Radio ROM from 1.41.00.11 to 1.46.00.11. Now I`m using 1.46.30.11 version and everything is OK. I even noticed a GPS signal level improvement.
Click to expand...
Click to collapse
Excellent idea. I'm currently using Radio version: 1.35.00.11...if I go to 1.4x - are these compatible with WM5?
anonimo said:
I am using a HTC-branded P3600 with the official HTC GPS-enabled WM5 ROM on the Vodafone UK network. With reasonable approximation I can say that I have 0 dropped calls (including calls made or received while in car).
Click to expand...
Click to collapse
Thank you anonimo - what radio version are you using?

BlackBeauty said:
Excellent idea. I'm currently using Radio version: 1.35.00.11...if I go to 1.4x - are these compatible with WM5?
Thank you anonimo - what radio version are you using?
Click to expand...
Click to collapse
I`m using a WM5 LVSW edition. Used it with 1.41.00.11 for 3 months without problems, changed to 1.46.00.11 for 2 days and encountered call drop issue, changed to 1.46.30.11 and not even a problem so far.

I am using my trinity with 1.41 and WM6 (AX3L) and I really never drop a call unless I step into an elevator. I am usually on UMTS or HSDPA living here in NYC and cannot complain about my service nor the phone.

BlackBeauty said:
Excellent idea. I'm currently using Radio version: 1.35.00.11...if I go to 1.4x - are these compatible with WM5?
Thank you anonimo - what radio version are you using?
Click to expand...
Click to collapse
I'm using version 1.35.00.11

Thanks for all the replies. Went ahead and upgraded ROM and Radio version to 3.00.707.16 and 1.46.30.11, respectively.
So far, no problems with call dropouts but I haven't made many long calls on it over the last 2 days but will keep assessing.
On the previous incarnation, I had also installed/uninstalled a LOT of programs over the 6 weeks I had had the phone so perhaps that contributed to the phone's instability too...

For me, it kinda worked the other way around...
I never experienced any call droppouts when I still had the original WM5 ROM with radio version 1.33.30.10 on my Dopod D810. (I'm with 3 in Australia)
After upgrading to the ANZ WM6 ROM with radio version 1.46.30.11, I can sometimes not even establish a connection as the call is dropped after the first ring or so. The other day I had to make a call 5 or 6 time to finish the conversation...
Is anybody else having similar issues AFTER upgrading?

Hi guys,
good to see that i'm not the only one that have call drop regularly.
Well, in fact, those are not always call drops.
Sometimes i miss calls and some other times, when i want to make a call, i see that my trinity's loosing the signal and starts to search for networks. Then i have to switch off the phone through the Connection Manager, then turn it on again so that i can make phone calls.
Are you experiencing the same on your device?
I'm still using Radio ROM 1.38.00.11
Do you guys have a link where to download the latest Radio ROM so that i can try it on my Trinity?
Thanks.

boy_in_oz said:
Is anybody else having similar issues AFTER upgrading?
Click to expand...
Click to collapse
Yep, I experience drops after upgrading... But the strange thing is... even after downgrading to the shipped rom... still drops... ARRGHHHHHH
I'm just going to try another rom I think... not sure yet. Have switched my band from auto to fixed. First gonna see what happens.

Some said it is due to 3G/3.5G trying to establish a data connection (most likely for push mail) and in doing so the phone function is disabled. I did not verify this claim.
If anyone wants to test it, you might want to try:
1. disabling 3G and 3.5G
2. disabling data connection
and tell us the results!

solitary said:
Some said it is due to 3G/3.5G trying to establish a data connection (most likely for push mail) and in doing so the phone function is disabled. I did not verify this claim.
If anyone wants to test it, you might want to try:
1. disabling 3G and 3.5G
2. disabling data connection
and tell us the results!
Click to expand...
Click to collapse
I will disable HSDPA. But I cannot disable my data connection because that's THE reason I bought my device for (using it for pushmail but I can use that with UMTS/GPRS connection also, don't need HSDPA for it).

I have found if I have network on AUTO i cant make calls, phone call drops straight away.
Switching to GSM allows me to make calls, but then I have no 3G

Found that radio rom 1.46.00.11 has no calls dropping for me. So I'm gonna stick with that one.
Cheers.

Arilexed said:
Found that radio rom 1.46.00.11 has no calls dropping for me. So I'm gonna stick with that one.
Cheers.
Click to expand...
Click to collapse
Just updated to radio rom 1.41.00.11, first few calls on UMTS dropped, then after a reset calls now working.

Arilexed said:
Found that radio rom 1.46.00.11 has no calls dropping for me. So I'm gonna stick with that one.
Cheers.
Click to expand...
Click to collapse
I have this ROM actually installed in my Trinity, and i still have call drops regularly
Once more today, it started to ring, then lost signal.
I'm wondering how much people has the same issue.

I used to have the same problem. I've reflashed my phone so many times coz of that.
But it seems like my problem's finally fixed
I'm using the most updated PDAVIET wm6 rom with Radio: 1.50.08.11
Been using that for about 2 weeks, haven't had a call drop since.
However I have had a few hangs here and there.
I run a lot of apps so the memory is pretty low most of the time. Yet for some reason I'm not getting any call drops so I'm happy. (Finally able to talk for like 15 mins without breaking up)
just fyi i'm also with 3, and don't have that band setting since I luv HSDPA yet certain areas only got Telstra reception...

Calls drop out
Hi, I'm in Sydney with 3 and haven't had any problems at all with the shipped WM5. After upgrading to the latest official WM6 ROM version 3.00.707.18 from the Dopd site things went bad with phone calls and weak signals.
Now upgraded the Radio to version 1.50.08.11 and everything's back to how it 's supposed to be.
Cheers and good luck.

Wireless Issue

Out of no where my wireless switch will not activate my wireless wifi connection. at all. I am using DCD 1.6.7. is anyone else having this problem?

pimpindexter said:
Out of no where my wireless switch will not activate my wireless wifi connection. at all. I am using DCD 1.6.7. is anyone else having this problem?
Click to expand...
Click to collapse
Yes!! I flashed the DCD rom on my friend's Mogul, and the wifi does not work. It activates, but it does not find any networks. I thought this was a hardware problem and suggested the HTC warranty or an insurance claim to my friend. But not, maybe not..

no, no...i think it is a hardware prob... it works sometimes for me with the OEM rom..and not other times.

what the hell is up with this!! it's the most annoying thing ever. I'm running dcd 1.6.10 and the signals (which are abundant) are only detected a small portion of the time and an even smaller portion of those times am I actually able to use the internet. so frustrating!

I THink WMWiFiRouter perm-killed my WiFi

So, I've been through 2 Moguls and both have the same problem.
First time, i downloaded and installed one of the newer builds of WMWiFiRouter. I started running it, turned on the hardware switch, and found my iPod Touch unable to get signal, despite the being inches away from the phone. I reset the install, and uninstalled it. running a new ROM, and the WiFi still didn't work. Read as "Unavailable" when it was on. So I called Sprint, and got a replacement, since i just assumed it had already been a replacement, and I assumed they gave it to me with Bum WiFi.
So Today I got the replacement. In the store i turned the hardware WiFi switch on, and got networks listed. I was happy to get WiFi on, so I installed WMWFR.. Again I received no signal. My Laptop couldn't see it at all. I upgraded the ROM, AND hard-Reset the device, and WiFi isn't even searching for local networks.

The only version that works for my Mogul is 1.20 any other version new or old I've tried doesn't work for me.. If you need a link PM me.

Version .89 works perfectly on DCD's 3.2.6
What rom/radio are you working with? I was afraid from the horror stories to upgrade wifirouter so I stuck with this one and is working perfectly.

Version .89 works perfectly on DCD's 3.2.6
What rom/radio are you working with? I was afraid from the stories to upgrade wifirouter so I stuck with this one and is working perfectly.
I just also remebered that a long while ago I had a custom rom running and when I was first introduced to wmwifirouter, can't remember which version, wifirouter would work but then I could not seek any wifi networks on my titan. I had to revert back to stock rom then flash new and a new version of wifirouter came out which took care of the problem.

Well i think i was running the M2D Round 4 ROM, and what ever the newest Sprint radio is, and tried it again. It killed my WiFi, again. I reflashed to Stock ROM and I still can't recieve any signals.

Wow, I stumbled upon this thread and I have to say that I have used WMWifiRouter since it came out and I have not ever had a problem with it on my Mogul. I have the latest version 1.25, could be there is a new update already, anyways it should back up your wifi settings, registry and all, before it does its thing. It does have a recovery feature in the options menu. I don't really know how it could stop your wifi from working. A hard reset should fix the problem since from what I understand it changes some of the registry settings so that it can bind the radio to the wifi.

The Difference
My question is:
When using WmWiFi Router, for those that are using it...did they buy it or torrent it?
Perhaps those with success are bought, and without are torrenting / using initial free versions.

have you guys with broken wifi seen this?
http://forum.xda-developers.com/showpost.php?p=2016704&postcount=728
try it and see how it works.

aguas said:
have you guys with broken wifi seen this?
http://forum.xda-developers.com/showpost.php?p=2016704&postcount=728
try it and see how it works.
Click to expand...
Click to collapse
I installed that and my phone won't boot past the HTC screen. I have DCD 3.2.6 rom with 2.40 radio. Performing hard reset now.....
oh, and i forgot to turn my wifi switch on while installing the cab, maybe that's the reason....?
edit: after the hard reset, I tried the cab again with my wifi on, still no luck... oh, and i did a soft reset, and it won't boot past the HTC screen.. another hard reset required.

Wifi will not activate

After flashing with a new ROM etc..
When I go into communications, and tap on wifi.....it turns on for a sec and then turns back off. Any suggestions?
Here is what I have done so far.....
Started with: Radio v. 1.39.00, ROM V. 2.13.656.2, Bootloader 1.2
Went to bootloader 2.40(via Hard-SPL-MF.exe), Scrosler's Titan ROM 3.26 w/touchflow. and then Radio 3.42.30.
Thank you in advance for any suggestions or solutions.
Reply With Quote

upsett3r said:
After flashing with a new ROM etc..
When I go into communications, and tap on wifi.....it turns on for a sec and then turns back off. Any suggestions?
Click to expand...
Click to collapse
Try the hardware switch on the side of the unit. The software switch was never able to work under most ROMs that I have ever used.

I toggled that (WiFi switch), and it does the same thing for me.

Should I try another ROM or radio version? I don't want to do a bunch of flashing.......anyone know a good firmware version (and radio v.) with everything working and ready to go in terms of functionality? I don't mind putting all the carrier info in etc, just want all the radios to work afterwards (wifi, eV(cellular data), cell, bluetooth, IR)

Never heard of the problem. I say reflash because something happened.

Changed the battery power option under wireless to best performance.....everything works now

That's odd behavior. Post if it happens again.
upsett3r said:
Changed the battery power option under wireless to best performance.....everything works now
Click to expand...
Click to collapse

When I use the ppckitchen my wifi refueses to work. I'm actually about to reflash it right now to DCD to see if it fixes it

Same Problem Here
The Switch seems to be malfunctioning...WHen I turn it off, it turns on the software for a second, then shuts off. WHen I turn it in the same thing happens. Really weird.
THis happened BOTH TIMES i reloaded the ROM.

im using the Kaiser Comm Manager(10 Buttons), and on it it always appears that the wifi is turned off, but functions fine with the switch

upsett3r said:
After flashing with a new ROM etc..
When I go into communications, and tap on wifi.....it turns on for a sec and then turns back off. Any suggestions?
Click to expand...
Click to collapse
i have the exact same problem since a couple of month and i cant seem to find a fix for that. I dont even know if the problem is software on hardware related.
i have used dcd 3.2.6 and 4.1.2
and im currently running ryan 2.0 i think wm6.1
maybe i should try wm 6.5
the only thing i know is that i would REALLY like my wifi to work :'(

lebulbe said:
i have the exact same problem since a couple of month and i cant seem to find a fix for that. I dont even know if the problem is software on hardware related.
i have used dcd 3.2.6 and 4.1.2
and im currently running ryan 2.0 i think wm6.1
maybe i should try wm 6.5
the only thing i know is that i would REALLY like my wifi to work :'(
Click to expand...
Click to collapse
i am using the ryan 2.0 wm6.1 and my wifi does not work either, didnt work in wm6.5 and no available memory in 6.5 either so save your time.
my phone was a mix of 2 broken moguls, the only thing i dont have working is vibrate and wifi

cturnbull802 said:
i am using the ryan 2.0 wm6.1 and my wifi does not work either, didnt work in wm6.5 and no available memory in 6.5 either so save your time.
my phone was a mix of 2 broken moguls, the only thing i dont have working is vibrate and wifi
Click to expand...
Click to collapse
DO you see a MAC address in the WLAN advanced settings?
If not, you just need to write a new MAC address and your WIFI will work, or so I have heard.
so... how do we enter in a MAC address if it is missing?
Anyone?

guys
theres no fix take it to sprint and they will replace it happen to me twice

VERY Strange WIFI problem

Ok
so for the last couple of days I've noticed that when at home, if I turn on the HD2's Wifi, my entire home network stops working. The router can no longer be accessed, even by wired Ethernet.
I figure it was a router issue, so I bought a newer better one by a different company - and what do you know: The same problem persists! As soon as I enable WiFi in my HD2 the router becomes unaccessible - and as I turn it off, all is well again.
I'm a computer technician, an MCSA and usually pretty good with those things, yet this issue baffles me. What on earth could cause that?
No other WIFI devices cause this issue, only my HD2.

Ambious said:
Ok
so for the last couple of days I've noticed that when at home, if I turn on the HD2's Wifi, my entire home network stops working. The router can no longer be accessed, even by wired Ethernet.
I figure it was a router issue, so I bought a newer better one by a different company - and what do you know: The same problem persists! As soon as I enable WiFi in my HD2 the router becomes unaccessible - and as I turn it off, all is well again.
I'm a computer technician, an MCSA and usually pretty good with those things, yet this issue baffles me. What on earth could cause that?
No other WIFI devices cause this issue, only my HD2.
Click to expand...
Click to collapse
What is the radio firmware version on the phone and what is the make, model and firmware revision of the router.
2 IT engineers are always better the one

My older router (with same problem) was 3Com 3CRWER200-75.
I replaced it with an Edimax BR-6524N. Same weird issue.
Both have latest firmwares.
My phone radio version... To be honst, I don't know how to check. My ROM version is 1.48.405.2 (71294) WWE - which is the stock rom of the Israeli version as supplied by Newpan.
Also worth mentioning, this didn't happen until a couple of days ago. Everyting was fine for months with the same exact configuration. SOMETHING must've changed, but what?
And how is it possible for my phone to kill two different routers?

I have the same problem with my laptop when running windows 7 but not linux....seems too me at least my problem is a driver issue.could be the damned for you too possibly. Was there a possible divert update on your phone?
I do not have an hd2 so I am not sure.
Edited for auto correct mistake

Ambious said:
My older router (with same problem) was 3Com 3CRWER200-75.
I replaced it with an Edimax BR-6524N. Same weird issue.
Both have latest firmwares.
My phone radio version... To be honst, I don't know how to check. My ROM version is 1.48.405.2 (71294) WWE - which is the stock rom of the Israeli version as supplied by Newpan.
Also worth mentioning, this didn't happen until a couple of days ago. Everyting was fine for months with the same exact configuration. SOMETHING must've changed, but what?
And how is it possible for my phone to kill two different routers?
Click to expand...
Click to collapse
You check your phone radio revision the same way you check your rom version. Go to settings, about phone, software information and look for the line "radio version".
Your actual rom version is quiet old and if you are still using a stock rom then you may want to have a look at the htc website for your country and see if you can get 1.66 rom or newer.
I personally have never experienced this problem but i always use linksys or netgear networking equipment. The linksys router i have at home i've had for many years (it's a wrt54g v2.0) and it still works perfectly even though it's cpu and networking chipsets are overclocked and it runs a custom firmware.

Well, the ROM is the latest available for my country :-(
But anyway, I managed to solve it by deleted all my wireless preferences and just 'rediscovering' my home network from scratch. Surprisingly that worked and solved the problem, even on my old router.
Now I'm wondering if I should return the new one and stick to my trust good old one, or stick with the new one? It was pretty expensive, and I don't really use an N wireless connection anywhere anyway, so... What do you think, XDA?

Ambious said:
Well, the ROM is the latest available for my country :-(
But anyway, I managed to solve it by deleted all my wireless preferences and just 'rediscovering' my home network from scratch. Surprisingly that worked and solved the problem, even on my old router.
Now I'm wondering if I should return the new one and stick to my trust good old one, or stick with the new one? It was pretty expensive, and I don't really use an N wireless connection anywhere anyway, so... What do you think, XDA?
Click to expand...
Click to collapse
You have no need for it, get your money back.

the hd2 is capable of N speeds. You just need to enable it in the registry. Personally i would use the old one till it dies and keep the newer one in a box till then but the choice is yours

The newer one is a lot of money I spent for something I didn't even need eventually. I'll be turning it back, I think.
Thanks to all who helped You guys rock!

Ambious said:
Well, the ROM is the latest available for my country :-(
But anyway, I managed to solve it by deleted all my wireless preferences and just 'rediscovering' my home network from scratch. Surprisingly that worked and solved the problem, even on my old router.
Click to expand...
Click to collapse
great to hear that you've found a solution!
A thought came to mind while reading this thread.
Wonder if it's possible that a certain radio file/setting on your HD2 might've been corrupted and instead of generating the usual wifi signal, it could've generated a signal on the same frequency that completely jammed you're router signal?
Similar to the radio jammer units available in some countries that can be used for GSM, Wifi, etc... just a thought!

Im glad you brought this up because I had the exact same problem (accept I could connect via ethernet just wifi went dead), almost brought a new router after spending 2 days trying to set it up :/ It wouldnt allow anything to see the router wifi wise let alone connect to it via wifi. I havent turned my wifi on the phone since then but ill try reseting my settings later to see if that works. I didnt wanna risk screwing the router over lol. Im on stock 1.48 rom and radio on o2 as well

bobbified said:
great to hear that you've found a solution!
A thought came to mind while reading this thread.
Wonder if it's possible that a certain radio file/setting on your HD2 might've been corrupted and instead of generating the usual wifi signal, it could've generated a signal on the same frequency that completely jammed you're router signal?
Similar to the radio jammer units available in some countries that can be used for GSM, Wifi, etc... just a thought!
Click to expand...
Click to collapse
That's an interesting thought, and if it's true - reversing it could be a tool for evil - just imagine being able to shut down networks just like that...
Anyway, I'm glad my issue was solved. That Edimax N router is really expensive, and I like my trusty old 3Com way better.

My N*kia n95 used to f*ck up the router like this sometimes