Bluetooth Address book sync with Ford Mondeo Handsfree - Touch Dual, MDA Touch Plus General

Hi,
Having problems with Address book sync with my new Touch Dual (orange Rom) and my Ford Mondeo Convers+ Bluetooth Handsfree kit. I did have the same problem with my work Hermes (also Orange M3100 Rom) until I did a Rom update to Schap’s 4.20+ Full Rom a couple months ago. Since then all works fine even without ‘JETware Hands-free Extension’ being loaded.
Checked for ‘SAP Access’ /’ Push Obex’ and both units are set the same.
I’ve checked both devices and they are both running the Microsoft stack shown by looking at the Bluetooth ‘HKLM\Drivers\Active’ driver registry area.
Does anyone know of a fix or have a idea?
Thanks in advance,
Crammy

I have a Focus, with the same Ford car kit.
My Hermes also couldn't transfer contact info to the car kit. I tried a variety of ROMs, enabling BT SAP and OBEX on each. It was only when I changed to Schaps 4.30 that it worked.
I can only assume that the Ford system is very picky about the BT SAP version, and only the very latest versions will work.
I suspect you will have to wait until someone releases a Niki ROM with a compatible BT SAP in it.

Related

Bluetooth and GPS problem

Hi all, I bought a Qtek S100 and tried to connect it with my BT GPS receiver (Falcom Navi 1). It didn't work properly and I suddely lost te BT icon on the lower right hand side of the S100. It hasn't re-appeared even after several soft resets?
Does the S100 have the sae BT problems with GPS as the xdaII had?
I use BT GPS and the only problem so far is that I have to re-pair them sometimes.
Try Start->Settings->Connections->Bluetooth to get to the same screen as you would get to by clicking the BT icon.
THanks for the reply. Which BT GPS do you use? and with what Navigation program?
Holux GR-231 and TomTom3.
I am having problem with Bluetooth GPS as well. I have 2, one is iTrek Bluetooth GPS and one is ArcoreTech Bluetooth GPS.
Since I have tried both GPS units, I am pretty sure it's i-Mate JAM's Bluetooth problem.
Instead of upgrading my ROM to 1.06.00 WWE, I should have tried it out with version 1.03 first. I upgraded from 1.03 to 1.06 as soon as my JAM finished charging. BIG MISTAKE!
I ended up usiing "Pocket Bluetooth Tool" to designate COM8 (for example) for my GPS. However, if I happen to soft reset or turn of Bluetooth, I would have to pair it again.
I read many article's on the internet and the problem seems to point to the MS Bluetooth stack (instead of Widcomm used in my i-Mate PDA2K - and by the way PDA2K works perfectly with my GPS units).
Hopefuly i-Mate will address this problem during the next ROM update.
So how come Loboman's holux works ok?
Loboman are you using a different BT stack?
I would like to guess that he uses ROM version 1.03...
Jazzedout said:
So how come Loboman's holux works ok?
Loboman are you using a different BT stack?
Click to expand...
Click to collapse
I use 1.06.00. All i do is that I tap on the BT icon, choose 'Devices', tap 'New...' and waits until the phone finds the GPS. Then I add it and pair it with the passkey. Then I had to scan all serial ports using a program that Holux supplies (I bet it works with any BT reciever though) to find out that my port was COM5 and finally I set my programs to use COM5. As I previously stated, I do have to re-pair them sometimes for some reason, but I can live with that.
I previously had an Acore unit which worked ok with my iPAQ 5450 (also MS BT stack) in WM2003. It took me all the way from northern Sweden to Barcelona in Spain last summer
I have not used Pocket Bluetooth Tool, but I have read about it. I think that it works without it so far. I also leave my BT on 24/7 since I don't think that it uses too much battery.
I hope things work out for you.
Absolutley no problems with Rom 1.01.01 Ger and Navilock BT-308 GPS-Mouse
I am not sure if the following has anything to do with Bluetooth but at least it cured my Bluetooth vs. GPS problem, for now.
On Club i-Mate's ROM update page, I found out that if the radio version is 1.10, then I am NOT suppose to apply the camera patch. After I uninstalled it, my JAM seems to work better with Bluetooth GPS units. My biggest problems were:
1. Once I soft reset my JAM, I have to re-pair my GPS units.
2. PrymeNav software took a long time to scan for GPS - and crashes sometimes when I designate already-scanned port.
3. Unable to hold two paired GPS units in Bluetooth Device List (though only used on at a time).
I have played with it after I uninstalled the camera patch and to this morning my GPS units still function well. Another key is to turn on the GPS unit and make sure it is linked (as indicated by its LED) - then turn on the GPS software. That way the hardwares are ensured to be linked.
As a side bonus, now I can perform Bluetooth Activesync on my Mac (via PocketMac software). However, I still require Pocket Bluetooth Tool installed on my JAM.
Weird!

MDA Compact (MDAc) and BMW Bluetooth Module (SA633)

Hi
I just got my new BMW 330 (E90) with Navigation and Bluetooth. I can pair my MDAc but that's it.
When a call comes in, My BMW signals it. Sometimes I can get the call with the button in the steering wheel. Sometimes not. Sometimes I can but the connection breaks down in the middle of the call.
I see the reception of my MDAc in the display and when a call comes I also see the number of the caller.
I cannot make a call (dial out).
I read a lot but did not find a solution yet. Has anyone experience with BMW carkits or any advice what to change in order to get it going. I sort of refuse to have another handy...
BTW I have the latest T-Mobile Update (1.12) but I did not install everything from the extended ROM.
I have exactly the same problem with Audi bluetooth, with my Nokia 6230 works perfectly, with my S100 I have the same problems you have experienced. I have an old ROM 1.06, but I see that even with 1.12 the problems are not solved.
I tell what I tried: I've installed various BT stacks (Toshiba, Widcomm, Bluesoleil also with crack). Toshiba pairs but does not find any service, Widcomm does not run, Bluesoleil does not have the needed profiles.
I have installed the CAB from VCABT project (see the thread in this forum), I can answer from the car I can call using the car voice command but I can't use the S100 buttons.
Hope that somebody could help us.
dgv
fdigianv, have you tried the new A2DP Stereo BT Tool to see if it works better with your Audi.
I just upgraded my JAM to 1.12 and have yet to try it with my Audi A6 4.2 2005 MMI BT System.
I'm tired of waiting for Audi to fix anything. It seems like the only fixes or upgrades they offer come in the form of a new car release.
I like you can call out from the Audi, but those on thger other end of the call complain about sound quality.
I'm getting ready to make a move to the new Treo MS Mobile device, or a smartphone that works better with my Audi.
I spoke to BMW this morning and they claim has more to do with the version of Bluetooth installed on the phone than BMW's implementation of Bluetooth.
BMW supports Bluetooth verson 2 and up.

Problems with BMW Bluetooth car kit

I've just got a Orange SPV M3100 and paired it with my BMW OEM bluetooth carkit, all goes fine and paired no problems.
It manages to connect to the phone and display contact details on the radio display and make calls.
But leaving it a couple of hours and coming back, the phone will not reconnect back to the car. I've tried resetting the phone without success.
The only way to get the connection back is to re-pair the devices.
I had a Imate Jamin before and it worked without a problem, connects every time.
Is anyone else experiencing problems with their carkits?
Do you think the problem is specific to the Orange ROM, would flashing it to a Imate or TyTN ROM help or resolve the problem?
Any advice would be greatly appricated.
Hi, I got a problem similar like yours...
I´m from Spain and I have an ´06 Opel Astra(Vauxhall in UK) with the BT handsfree carkit from factory.
If I make a hard reset to my Vodafone S200 (Orange SPV M600) and leave the machine with the factory settings it works fine with the carkit, but it recognice the carkit like a headset handsfree. But if i restore a back up with the TomTom 6 installed... wow, then start the problems... the handsfree conect with the S200 but after a few seconds the connection is over...
I don´t know if have you got some kind of navigation system, but in my case the problems starts when I install the TomTom... I´m sure it changes some drivers of the BT and this makes the don´t works propertly.
I don´t know what to do...
PArrot Car Kit
I have the same problem with Parrot Car Kit and I have the latest TYTYN ROM
2006 BMW 3-Series Bluetooth
My car doesn't have bluetooth, but I had a loaner car while my car was under the knife. The loaner car was a 2006 3-series w/ Bluetooth. The first pair was perfect, but after a few hours.. What a POS.
I have the latest ROM on my phone, and that didn't make a difference.
No issues on my 5 series, but I have one of the first ULF modules in mine.
From reading TyTN Bluetooth issues around the net and on this forum, it seems to be an issue with the TyTN having some kind of power save mode which turns the bluetooth off after some time.
Kinda stupid, anyone know some registry crack to turn any power saving off?
I have a Parrot CK3100 in a BMW and a brand new SPV M3100. All was working well with my M600 but as soon as I swapped the phone for the M3100 last week I've had problems as described by the OP. Bluetooth keeps switching itself off on the SPV. It works well enough to start with and then suddenly it disconnects. Re-pairing works and it's worth going to bluetooth settings and turning it back on again before you try re-pairing.
Surely there must be an easy fix for this problem - I'm just really pleased I'm not the only one with this fault.
............
Your all quite lucky it works at all..mine doesn't do anything
My Ford Fiesta has been waiting for an 'software upgrade' since October !!
Promised it would be available before Xmas but nothing happened.
lifterus said:
Try and replicate the problem with a different phone if possible. One that BMW supports. If can replicate it, then they'll update the firmware on the BT unit in the car. This happened to me. But I had to prove my case using my girlfriend's RAZR before they'd listen and stop blaming my phone as the cause.
Click to expand...
Click to collapse
I dont think it is a problem with the BMW carkit as it worked fine with my SPV M600 (Prophet)

Tytn & Sap Problem With Mercedes

Hi my friends, I have problems to connect my Tytn with my Mercedes Benz bluetooth UHI interface system.
Have you notice about this bug ? I have installed Jetware test build but the problem is the same.
Thank you for your courtesy
A friend of mine had the same problem, seems you need upgrade to WM6 to fix the connection with your Benz.
Bye
I have WM6 but the problem is the same. Do you know if your friend has operated other operation ?
I have just purchased a TyTN II which won't connect with the Mercedes SAP car kit. It gets as far as finding the device but when the car kit tries to send the pairing code it fails.
Go to http://www.benzworld.org/forums/audio-telematics-forum/ and/or look on the site for your specific vehicle group such as W163 or whatever yours is.
Mercedes - Tytn integration
So it looks like one of the few options is by sending virtural cards to the mercedes thing...
Problem is that you need to do this one by one... any way to automate this? a script or something?
I would be happy already if i could synchronize, copy all my contacts to the mercedes memory every now and then...

Problem with BMW BLUETOOTH

Hello have this pHone and it can not connect witha 2005 BMW X5 his Bluetooth modul. As soon it starts connecting and load the phonebook the Cruise resets himself .
Any tip on this
Do you try the bluetooth update for cruise available on htc e-club ?
there is no update for this
thanks for this but i looked there first amd the updates bare for differnt problems. anyway tried it, didn't helped.
BMW bluetooth
I installed the jetware something app in order to synv with my bMW, works fine

Categories

Resources