I've had my Wallaby for a while, and for some weird reason it just stopped working (froze). I tried to format it (Hard Reset) to get it going again, but all it did was just hang at the logo screen.
Now, I've tried, and unsuccessfully, to get it to work by reflashing the ROM.
That hasn't worked. In fact, now I can no longer get to the boot-loader.
Please help!
This phone is a great phone!
Related
My HTC was flashed with TNT. It has 2.21.0001 and 2.21.Olip. I can boot it to boot loader. I can reset it, with switch or pulling the battery. Every time it boots showing the versions, then comes to a WM6 boot screen. This is normal. However it never comes out of this screen. The LEDs flash as if it were working, but the phone is unresponsive.
Is there any way to fix this?
Do I need to reset it in some way? If so, how?
i had a same problem with TNE. after it worked fine for a year.
then i changed the rom to a new 1 and fixed all my problems . just upgraded it in bootloader mode.
Same problem. I installed BlackDiamond2.0. At the begginning everything was ok, then Send button wouldn't work till I press the Start button on the querty keyboard.
Just playing, I tried to overlook with an application that came on the package and then it didn't work any longer. It stays at the BlackDiamond picture.
And I cannot make a hard reset since Send button don't work and cannot connect with Active Sync to flash the rom.
Any idieas?
also could be a bad battery. happened with my brothers phone. acted the same way.
our phones are old now. get a replacement 10 bucks.
Hi there , i recently tried to flash the rom of my vogu100,it didn't work well so i had to do a hard reset, everything is fine, it goes trough the reseting process fine,but when it restart , it stays at the bell blue screen.I tried to plug the usb to the pc to reflash the rom but nothing shows up !!!!!! What should i do!!!!!!!!
okay after a lot of researche i foud how to get in bootloader mode after restarting my unit,i then have pressed the power button camera button and tapped the reset button as if i was doin' a hard reset,i then got in bootloader mode and was able to install the new rom from bell . everythings work fine now.God i tought it was dead.
ya, my phone started hanging at the bell screen yesterday, had to reflash to get it back up and running. im not sure what caused this as i havent flashed in a few weeks.
Hi Guys,
I was in the middle of flashing my OMNIA 7 then suddenly my computer shutdown due to a blackout at our home. Now my phone is stuck on the OMNIA 7 logo during boot and keep going that way.
I could still manage to go to download mode and reflash but when I try to flash it there is an error that would indicate "WRITE MIBIB FAILED!"
Is my phone bricked? I need your help.
By the way, if I get still manage to go to the DOWNLOAD MODE would that mean that my phone is not bricked?
Thanks!
Have you tryed formating before you try? Just use the other volym button.
Tryed yet?
Yeah I tried it, but still not working. . I still manage to get to "download mode" though.
As I have read through the different posts in the forum I see people experiencing the same problem such as the phone which keep on restarting and stuck on the "OMNIA 7" startup logo. . I tried the fixes that other's recommended but still doesn't work.
I tried taking the battery out for a day then putting it back in, the phone managed to boot up and I was actually able to use it but if I try to restart it again or sync it to the computer, It suddenly resets then goes on the boot loop once again. .
Well then I guess there is only one way. Return it to the store. :'(
to flash, ALWAYS restart your computer before and use a laptop with charged battery to avoid this problem.
For your problem you can tried to flash only bootloader part, radio part, or only PDA part for testing.
hay man
I had the same problem and here is the solution
follow the this link http://support.microsoft.com/kb/2530409/en-us
it works 100%
I hope it works with you as well
Nice one Abd654. Hope that helps you bor. GL
I have a problem getting in to "Connect to PC" I followed the instructions on holding the power and camera buttons, etc. but it won't go to "connect to pc" screen. . it's just keeps on flashing the "Samsung Omnia 7 logo" on the screen everytime I turn it on.
I tried doing hard reset but I cant because once the hard reset screen shows up, the phone just restarts again then the start up loop happens again. .
try this one this is from microsoft answer
http://support.microsoft.com/kb/2547687/en-us
I loaded Yuki's ROM and updated to Mango via Zune. Had it running for about a week before I discovered that when I turn off the phone and then turn back on, it gets stuck at the point where it should be loading the home screen. I get the time at the top and that's it; the phone is completely unresponsive. The only fix I found was to do a hard reset and start over. I thought maybe an application caused this so after the reset, I turned off the phone before loading any other applications. It got stuck again at the same place. I suppose this could be linked to the sd card and I'll try a different one. Just wanted to see if anyone else has experienced this problem.
--Edit--
I've linked my issue to the sd unlock cab. As long as I don't install, mango restarts with no problems.
I've had this a few times.
Usually get the lockup at the SIM password screen.
Just reboot again and it will come back. Sometimes a couple of boots are needed.
I have a supported Sandisk card BTW.
Thanks. I've given it 2 tries before the reset but not more. I'll try to be more patient with it this time...or just avoid turning it off
I had the same problem as well, reflashed it with the same problem. after doing about 3 hard resets it finally worked.
I'm getting this continually, every time i reset i end up having to hard reset...
I've been using my tablet for 2 years. Yesterday, my tablet froze for the 3rd time. When I reboot it, it always stuck on logo screen. I used to solve this by pressing the volume buttons randomly. Unfortunately, by doing it for like 3 times, it doesn't work anymore, so I decided to do the hard reset. When I did the wipedata/factoryreset, it seems that it failed to do the wiping process because I was stuck with the boot loop but it loops the wiping process. After that, it stops to a green android that has a big red triangle inside of it. Believe me, I tried understanding the forums regarding to this, but it doesn't quite fit to my situation. I didn't tweak or change any firmware and application. It just had boot loops. Now, it's fully shutdown. I hope I can recover my tablet.
I hope the answers/guide can be somehow understandable to noobs like me.
Thank you for reading.
Lenova Ideatab A3000
Hello...
Same problem with my tab :crying:.. I have been using the tab for 3 years. Now It's stuck on the logo and when I tried rebooting it didn't work. Later when it's switched on, it's showing some countries symbol in the Chinese language. It is also no use because after selecting the country it says "Timeout, Failed". The tab is not detected after connect to PC. .. Somebody please help me with this.
hiddenathena said:
I've been using my tablet for 2 years. Yesterday, my tablet froze for the 3rd time. When I reboot it, it always stuck on logo screen. I used to solve this by pressing the volume buttons randomly. Unfortunately, by doing it for like 3 times, it doesn't work anymore, so I decided to do the hard reset. When I did the wipedata/factoryreset, it seems that it failed to do the wiping process because I was stuck with the boot loop but it loops the wiping process. After that, it stops to a green android that has a big red triangle inside of it. Believe me, I tried understanding the forums regarding to this, but it doesn't quite fit to my situation. I didn't tweak or change any firmware and application. It just had boot loops. Now, it's fully shutdown. I hope I can recover my tablet.
I hope the answers/guide can be somehow understandable to noobs like me.
Thank you for reading.
Click to expand...
Click to collapse
Flash your phone.
You can go to this thread if you want to flash an Original Jellybean Rom. All the tools you will need and a tutorial.
http://forum.xda-developers.com/len...000-h-call-t2441135/post45510235#post45510235
If you want to upgrade to a Kitkat Custom Rom, there is this thread. Also with all the tools and a tutorial.
http://forum.xda-developers.com/lenovo-a3000/orig-development/rom-lenovo-a3000-h-aosp-4-4-2-t3414278